Silicon Photonic Wire Waveguides Research Articles

Hybrid laser diode with ultrawide wavelength-tunable range using curved directional couplers.

Wavelength-tunable laser diode with a wide tuning range is required for optical communication systems and optical sensing. External cavity laser diodes with silicon-photonic wire waveguides and ring resonators have small footprint because of high refractive index contrast between Si. However, power coupling efficiency κ of conventional straight directional coupler between ring and bus waveguides have large wavelength dependence, which lowers tunable range. In this study, we demonstrate a hybrid wavelength-tunable laser diode using curved directional couplers, whose wavelength dependence on κ is low. The wavelength-tunable range record of 120.9 nm has been achieved. In addition, curved directional couplers are tolerant of waveguide width fabrication error.

Novel Low-Loss Fiber-Chip Edge Coupler for Coupling Standard Single Mode Fibers to Silicon Photonic Wire Waveguides

Fiber-to-chip optical interconnects is a big challenge in silicon photonics application scenarios such as data centers and optical transmission systems. An edge coupler, compared to optical grating, is appealing to in the application of silicon photonics due to the high coupling efficiency between standard optical fibers (SMF-28) and the sub-micron silicon wire waveguides. In this work, we proposed a novel fiber–chip edge coupler approach with a large mode size for silicon photonic wire waveguides. The edge coupler consists of a multiple structure which was fulfilled by multiple silicon nitride layers embedded in SiO2 upper cladding, curved waveguides and two adiabatic spot size converter (SSC) sections. The multiple structure can allow light directly coupling from large mode size fiber-to-chip coupler, and then the curved waveguides and SSCs transmit the evanescent field to a 220 nm-thick silicon wire waveguide based on the silicon-on-insulator (SOI) platform. The edge coupler, designed for a standard SMF-28 fiber with 8.2 μm mode field diameter (MFD) at a wavelength of 1550 nm, exhibits a mode overlap efficiency exceeding 95% at the chip facet and the overall coupling exceeding 90%. The proposed edge coupler is fully compatible with standard microfabrication processes.

Numerical simulation of low loss silicon photonic wire waveguide with multiple cladding layers

A different silicon photonic wire waveguide is proposed, which uses multiple thin cladding layers in order to reduce the index contrast between core and cladding interface. The reduced index contrast in the proposed waveguide has led to reduction in the scattering losses by 37% as compared to silicon wire waveguide for 400 nm × 220 nm waveguide dimension. The proposed waveguide has shown significant reduction in bending losses. It offers the bending loss of 0.0118 dB at the radius of 1 μm and 0.0063 dB for a radius of 2 μm at 1.55 μm wavelength as compared to 0.086 and 0.013 dB at the radius of 1 and 2 μm, respectively, offered by silicon photonic wire waveguide at 1.5 μm wavelength. The use of polymer material as top cladding layer resulted in decreasing the sensitivity of effective index against temperature for the designed waveguide by a factor of 2 as compared to silicon wire waveguide.

Fiber-chip edge coupler with large mode size for silicon photonic wire waveguides.

Fiber-chip edge couplers are extensively used in integrated optics for coupling of light between planar waveguide circuits and optical fibers. In this work, we report on a new fiber-chip edge coupler concept with large mode size for silicon photonic wire waveguides. The coupler allows direct coupling with conventional cleaved optical fibers with large mode size while circumventing the need for lensed fibers. The coupler is designed for 220 nm silicon-on-insulator (SOI) platform. It exhibits an overall coupling efficiency exceeding 90%, as independently confirmed by 3D Finite-Difference Time-Domain (FDTD) and fully vectorial 3D Eigenmode Expansion (EME) calculations. We present two specific coupler designs, namely for a high numerical aperture single mode optical fiber with 6 µm mode field diameter (MFD) and a standard SMF-28 fiber with 10.4 µm MFD. An important advantage of our coupler concept is the ability to expand the mode at the chip edge without leading to high substrate leakage losses through buried oxide (BOX), which in our design is set to 3 µm. This remarkable feature is achieved by implementing in the SiO2 upper cladding thin high-index Si3N4 layers. The Si3N4 layers increase the effective refractive index of the upper cladding near the facet. The index is controlled along the taper by subwavelength refractive index engineering to facilitate adiabatic mode transformation to the silicon wire waveguide while the Si-wire waveguide is inversely tapered along the coupler. The mode overlap optimization at the chip facet is carried out with a full vectorial mode solver. The mode transformation along the coupler is studied using 3D-FDTD simulations and with fully-vectorial 3D-EME calculations. The couplers are optimized for operating with transverse electric (TE) polarization and the operating wavelength is centered at 1.55 µm.

A two-stage photonic crystal fiber / silicon photonic wire short-wave infrared wavelength converter/amplifier based on a 1064 nm pump source.

We demonstrate a two-stage wavelength converter that uses compact near-infrared sources to amplify and convert short-wave infrared signals. The first stage consists of a photonic crystal fiber wavelength converter pumped by a Q-switched 1064 nm pump source, while the second stage consists of a silicon photonic wire waveguide wavelength converter. The system enables on-chip amplification and conversion of up to 30 dB . We demonstrate amplification in a broad wavelength range around 2344 nm using temporally long pulses (>300ps).

Vertically coupled plasmonic slot waveguide cavity for localized biosensing applications

We propose and study an integrated refractive index sensor which is based on a plasmonic slot waveguide cavity. In this device, a guided mode supported by a silicon photonic wire waveguide is vertically coupled to a metal-dielectric-metal cavity separated by a silicon oxide spacer. We perform an in-depth study that links the geometrical parameters of the sensor to the coupling mechanism and sensitivity of the plasmonic slot waveguide cavity. Simulation results promise that local changes of refractive index can be measured with a high sensitivity of around 600 nm/RIU in a femto-liter volume. These results are obtained with three-dimensional time and frequency domain simulations. Thanks to the high field enhancement in the slot of the plasmonic cavity, a high local sensitivity to changes of refractive index is obtained. Moreover, the high level of achieved decoupling between the bulk and the local sensitivity complies well with the requirements of biomolecular sensing.

Pulse compression in adiabatically tapered silicon photonic wires

We present a comprehensive analysis of pulse compression in adiabatically tapered silicon photonic wire waveguides (Si-PhWWGs), both at telecom (λ ∼ 1.55 μm) and mid-IR (λ ≳ 2.1 μm) wavelengths. Our theoretical and computational study is based on a rigorous model that describes the coupled dynamics of the optical field and photogenerated free carriers, as well as the influence of the physical and geometrical parameters of the Si-PhWWGs on these dynamics. We consider both the soliton and non-soliton pulse propagation regimes, rendering the conclusions of this study relevant to a broad range of experimental settings and practical applications. In particular, we show that by engineering the linear and nonlinear optical properties of Si-PhWWGs through adiabatically varying their width, one can achieve more than 10× pulse compression in millimeter-long waveguides. The inter-dependence between the pulse characteristics and compression efficiency is also discussed.

Photonic wire biosensor microarray chip and instrumentation with application to serotyping ofEscherichia coliisolates

A complete photonic wire molecular biosensor microarray chip architecture and supporting instrumentation is described. Chip layouts with 16 and 128 independent sensors have been fabricated and tested, where each sensor can provide an independent molecular binding curve. Each sensor is 50 μm in diameter, and consists of a millimeter long silicon photonic wire waveguide folded into a spiral ring resonator. An array of 128 sensors occupies a 2 × 2 mm2 area on a 6 × 9 mm2 chip. Microfluidic sample delivery channels are fabricated monolithically on the chip. The size and layout of the sensor array is fully compatible with commercial spotting tools designed to independently functionalize fluorescence based biochips. The sensor chips are interrogated using an instrument that delivers sample fluid to the chip and is capable of acquiring up to 128 optical sensor outputs simultaneously and in real time. Coupling light from the sensor chip is accomplished through arrays of sub-wavelength surface grating couplers, and the signals are collected by a fixed two-dimensional detector array. The chip and instrument are designed so that connection of the fluid delivery system and optical alignment are automated, and can be completed in a few seconds with no active user input. This microarray system is used to demonstrate a multiplexed assay for serotyping E. coli bacteria using serospecific polyclonal antibody probe molecules.

Single silicon wire waveguide based delay line interferometer for DPSK demodulation

We experimentally demonstrate a high-quality phase shift keying demodulator based on a silicon photonic wire waveguide. Since the birefringence of the waveguide generates extremely huge differential group delay, an ultra-compact and high-extinction-ratio delay line interferometer is devised in TE and TM modes. We firstly calculated and simulated the requirements for propagation length and waveguide's dimensions. Then, we measured the interference spectrum, eye pattern, bit error rate, and temperature dependence to ascertain its feasibility for DPSK demodulation. For a 2.8 cm-long wire waveguide, a free spectral range of 9.6 GHz and an error-free DPSK demodulation around 10 Gb/s are obtained.

Silicon microring resonators

AbstractAn overview is presented of the current state‐of‐the‐art in silicon nanophotonic ring resonators. Basic theory of ring resonators is discussed, and applied to the peculiarities of submicron silicon photonic wire waveguides: the small dimensions and tight bend radii, sensitivity to perturbations and the boundary conditions of the fabrication processes. Theory is compared to quantitative measurements. Finally, several of the more promising applications of silicon ring resonators are discussed: filters and optical delay lines, label‐free biosensors, and active rings for efficient modulators and even light sources.

Temperature-independent silicon subwavelength grating waveguides

We demonstrate, by experiment and numerical calculations, temperature-independent subwavelength grating waveguides with a periodic composite core composed of alternating regions of silicon and SU-8 polymer. The polymer has a negative thermo-optic (TO) material coefficient that cancels the large positive TO effect of the silicon. Measurements and Bloch mode calculations were carried out over a range of silicon-polymer duty ratios. The lowest measured TO coefficient at a wavelength of 1550 nm is 1.8×10(-6) K(-1); 2 orders of magnitude smaller than a conventional silicon photonic wire waveguide. Calculations predict the possibility of complete cancellation of the silicon waveguide temperature dependence.

Loss reduction in silicon nanophotonic waveguide micro-bends through etch profile improvement

Single mode silicon photonic wire waveguides allow low-loss sharp micro-bends, which enables compact photonic devices and circuits. The circuit compactness is achieved at the cost of loss induced by micro-bends, which can seriously affect the device performance. The bend loss strongly depends on the bend radius, polarization, waveguide dimension and profile. In this paper, we present the effect of waveguide profile on the bend loss. We present waveguide profile improvement with optimized etch chemistry and the role of etch chemistry in adapting the etch profile of silicon is investigated. We experimentally demonstrate that by making the waveguide sidewalls vertical, the bend loss can be reduced up to 25% without affecting the propagation loss of the photonic wires. The bend loss of a 2μm bend has been reduced from 0.039dB/90° bend to 0.028dB/90° bend by changing the sidewall angle from 81° to 90°, respectively. The propagation loss of 2.7±0.1dB/cm and 3±0.09dB/cm was observed for sloped and vertical photonic wires respectively was obtained.

Refractive-Index Engineering of Planar Waveguides with Subwavelength Gratings

I integrated photonic circuits, the refractive-index contrast is usually set by the choice of the material platform. For example, for silicon photonic circuits operating at a wavelength near l= 1.55 μm, the waveguide core and the cladding indices are given by the material constants of silicon (n = 3.5) and silicon dioxide (n = 1.44), and waveguide devices must be designed within the constraint of these fixed values. From free-space optics, we know that periodic dielectric structures with a periodicity smaller than one half of the wavelength do not diffract any light. Instead, such so-called subwavelength gratings (SWGs) act as homogeneous effective media with spatially averaged refractive index.1 We have recently demonstrated the first use of SWGs for refractive-index engineering in microphotonic waveguides, providing a powerful method for controlling the refractive index of a waveguide core in any specific location of a photonic chip. Importantly, our method only relies on standard fabrication techniques and can be implemented without any modifications to the chip fabrication process flow. The structure shown in (a) exemplifies refractive-index engineering of a silicon photonic wire waveguide. By etching periodic gaps of a well-defined width w and pitch L into a standard silicon photonic wire, an SWG waveguide is formed with an effective core index determined by the duty ratio w/L. Calculation of the dispersion relation of the segmented waveguide and comparison with the dispersion of an equivalent photonic wire waveguide with identical cross section and a core index of n = 2.65, as shown in (b) confirms theoretically the concept of spatial refractive-index averaging. Experimentally, we have observed waveguiding in such SWG structures with a propagation loss as low as 2.1 dB/cm, comparable to the best photonic wire waveguides reported, and with a low and nearly wavelengthindependent group index, as predicted by theory.2 Although consistent with Bloch theory, it is fascinating to observe light propagating almost unperturbedly through so many strong discontinuities.3 Among the applications of SWG waveguides4 is an SWG slab waveguide structure that simultaneously acts as a lateral cladding for a photonic wire waveguide in a novel microspectrometer design and an efficient in-plane fiberchip coupling structure. The coupler structure works by gradual modification of the waveguide core index, leading to mode-size transformation between a high-index photonic wire and the lowindex optical fiber. Measured coupling loss is 0.9 dB for TE and 1.2 dB for TM polarization. SWG waveguides were also implemented for highly efficient waveguide crossings,5 such as those shown in (c). (a) SEM image of an SWG waveguide. (b) Dispersion relation of an SWG waveguide and an equivalent photonic wire waveguide with core refractive index of 2.65 (TE polarization). (c) SWG waveguide crossings. (a)

Entanglement Generation Using Silicon Photonic Wire Waveguide

This paper reviews recent progress on telecom-band entangled photon-pair sources based on spontaneous four-wave mixing (SFWM) in a silicon photonic wire waveguide. Thanks to the large third order nonlinearity of nano-scale silicon waveguides, we can generate photon pairs efficiently. Moreover, the use of silicon waveguides enable us to avoid the noise photons caused by spontaneous Raman scattering, which has been a serious problem with entanglement sources based on SFWM in dispersion shifted fiber. We successfully demonstrated high-purity time-bin and polarization entanglement generation using 1-cm long silicon waveguides.

Silicon photonic wire biosensor array for multiplexed real-time and label-free molecular detection

We demonstrate a silicon photonic wire waveguide biosensor array chip for the simultaneous monitoring of different molecular binding reactions. The chip is compatible with automated commercial spotting tools and contains a monolithically integrated microfluidic channel for sample delivery. Each array sensor element is a 1.8-mm-long spiral waveguide folded within a 130 microm diameter spot and is incorporated in a balanced Mach-Zehnder interferometer with a near temperature independent response. The sensors are arranged in a 400 microm spacing grid pattern and are addressed through cascaded 1x2 optical power splitters using light from a single input fiber. We demonstrate the real-time monitoring of antibody-antigen reactions using complementary and mismatched immunoglobulin G receptor-analyte pairs and bovine serum albumin. The measured level of detection for each sensor element corresponds to a surface coverage of less than 0.3 pg/mm(2).

Compact, lower-power-consumption wavelength tunable laser fabricated with silicon photonic-wire waveguide micro-ring resonators

A wavelength tunable laser with an SOA and external double micro-ring resonator, which is fabricated with silicon photonic-wire waveguides, is demonstrated. To date, it is the first wavelength tunable laser fabricated with silicon photonic technology. The device is ultra compact, and its external resonator footprint is 700 x 450 microm, which is about 1/25 that of conventional tunable lasers fabricated with SiON waveguides. The silicon resonator shows a wide tuning range covering the C or L bands for DWDM optical communication. We obtained a maximum tuning span of 38 nm at a tuning power consumption of 26 mW, which is about 1/8 that of SiON-type resonators.

Compact four-channel reconfigurable optical add-drop multiplexer using silicon photonic wire

We designed and fabricated a four-channel reconfigurable optical add-drop multiplexer based on silicon photonic wire waveguide, which is controlled through the thermo-optic effect. The effective footprint of the device is about 1000 × 500 μm 2. The minimum insertion loss including the transmission loss and coupling loss is about 10.7 dB. The tuning bandwidth is about 17 nm, the average tuning efficiency about 6.11 mW/nm and the tuning speed about 24.5 kHz.

Compact and low power thermo-optic switch using folded silicon waveguides

By exploiting the small bend radius achievable using high-index-contrast silicon photonic wire waveguides, we demonstrate a new low power thermo-optic switch arranged in a dense, double spiral geometry. Such a design permits the waveguide length to be extended for increased phase shift, without the need for increased heated volume. This provides an effective means to reduce the power consumption of thermo-optic switches, as well as a compact geometry desirable for the development of switch arrays. A low switching power of 6.5 mW was obtained for a spiral-path Mach-Zehnder interferometer device having a 10% - 90% rise time of 14 micros. The switching power is shown to be reduced by more than 5 times compared to a Mach-Zehnder interferometer employing a conventional straight waveguide geometry.

Waveguide grating coupler with subwavelength microstructures

We propose a silicon waveguide-fiber grating coupler that uses a subwavelength microstructure to achieve a continuously variable grating strength yet can be fabricated using only a single etch step. By adjusting the subwavelength microstructure at every point along the grating, the grating coupler can be optimized to give high field overlap with the optical fiber mode and also minimize backreflections along the incident waveguide path. Our design example is optimized for quasi-TM mode in a silicon photonic-wire waveguide, as required for waveguide evanescent-field-sensing applications. A field overlap of up to 94% with a standard single-mode optical fiber (SMF-28) is achieved by coupler apodization. Backreflection from the grating is reduced to ~0.1%, and the total predicted photonic wire to fiber coupling efficiency is 50%.

Four-channel reconfigurable optical add-drop multiplexer based on photonic wire waveguide

We designed and fabricated a four-channel reconfigurable optical add-drop multiplexer based on silicon photonic wire waveguide controlled through thermo-optic effect. The effective footprint of the device is about 1000 x 500 microm(2). The minimum insertion loss is about 10.7 dB and the tuning bandwidth about 17 nm. The average tuning power efficiency is about 6.187 mW/nm and the tuning speed about 24.4 kHz. The thermo-optic polarization-rotation effect is firstly reported in this paper.