Silicon Photomultipliers Research Articles

Spaceborne COTS-Capsule hodoscope: Detecting and characterizing particle radiation

The COTS-Capsule Spaceborne hodoscope was launched into low Earth orbit aboard the International Space Station and operated from 2021 to 2022. The primary objectives of the payload are measuring and characterizing the radiation environment within the space station, serving as a technology demonstrator for the COTS-Capsule radiation mitigation apparatus, and testing the interaction of high-energy cosmic particles on-orbit with our detectors. The payload features a particle hodoscope equipped with an array of novel detectors based on polyvinyl toluene scintillators and silicon photomultiplier sensors that are used for radiation detection and characterization employing 2D intensity-based triangulation. This paper provides a comprehensive account of the COTS-Capsule payload’s construction, preflight performance, testing, qualification, and on-orbit calibration. The hodoscope, sensitive to ionizing cosmic particles, facilitates impinging particle track reconstruction by multi-detector 2D position estimation, energy deposition estimation, and linear energy transfer estimation.

Performance evaluation of a small-animal PET scanner with 213 mm axis using NEMA NU 4-2008.

Long-axis positron emission tomography (PET) has emerged as one of the recent research directions in PET due to its ability to significantly enhance sensitivity and counting performance for low-dose imaging, rapid imaging, and whole-body dynamicimaging. The PET system presented in this study is a long-axis animal PET based on lutetium-yttrium orthosilicate and silicon photomultiplier, designed for whole-body imaging in rats. It features a diameter of 143 mm and an axial length of 213.3 mm. This study evaluated the performance of this PET system in accordance with the National Electrical Manufacturers Association (NEMA) NU 4-2008standards. The performance evaluation was conducted according to the NEMA NU 4-2008 standards in terms of spatial resolution, sensitivity, counting rate performance, scatter fraction (SF) and image quality. In addition, a rat imaging study was conducted to assess the imaging capability of this PETsystem. The average energy resolution of the PET system was 12.87%, the average coincidence timing resolution was 751 ps. The FWHM of spatial resolution reconstructed by filtered back projection and 3D-OSEM-PSF algorithm at 5 mm radial offset from the axial center were 1.65 and 0.88 mm. The peak absolute sensitivity measured by a point source at the center of the field of view was evaluated as 6.71% (361-661keV) and 10.31% (250-750 keV). For the mouse-like phantom, the SF was 11.0% and the peak noise equivalent counting rate (NECR) was 1193 kcps at 94.2 MBq (2.54 mCi). For the rat-like phantom, the SF was 26.8% and the NECR was 682.5 kcps at 78.6 MBq (2.12 mCi). The performance measurement results demonstrate that this PET system exhibits high sensitivity and count rate performance, making it potential for high-quality whole-body dynamic imaging ofrats.

A study method using early dynamic acquisition of [18F]fluorodopa positron emission tomography for the differential diagnosis between progression and radionecrosis of brain metastases after radiotherapy

BackgroundIt is difficult to distinguish between the brain metastasis progression (BMP) and brain radionecrosis (BRN) on the basis of 18F-3,4-dihydroxyphenylalanine positron emission tomography/computed-tomography (18F-FDOPA PET/CT) data. The advent of silicon photomultiplier (SiPM) PET technology makes it possible to study dynamic volumes and potentially improve diagnostic accuracy. We developed a method for processing 18F-FDOPA PET/CT in the differential diagnosis between BMP and BRN. The method involves a short (3-second) sampling time during a 4-minute acquisition on a SiPM-PET/CT machine. We prospectively included 15 patients and 19 metastases. All acquisitions were performed in list mode acquisition for 25 min on a four-ring SiPM PET/CT system. We calculated the ratios between the maximum activity in the lesion’s voxel and the mean activity in the contralateral region (VOImax/CLmean) or the mean activity in the white matter (VOImax/WMmean).ResultsSeven lesions were classified as BMP and twelve were classified as BRN. Statistically significant intergroup differences in the VOImax/CLmean and VOImax/WMmean activity ratios were observed for both the clinical volume and the early acquisition. The best performing quantitative variable was the VOImax/CLmean ratio on early acquisition, with a diagnostic accuracy of 94.7%, a sensitivity of 100%, and a specificity of 91.7%.ConclusionThe 18F-FDOPA PET/CT data acquired a few minutes after the bolus injection confirms its value in differentiating between BMP and BRN, compared to the much longer classic clinical protocol.

Ski S. V. Influence of gamma irradiation on the reverse current-voltage characteristics of silicon photomultipliers

The study investigated the effect of Co60 gamma-quanta on the reverse current-voltage characteristic (IV) of silicon photomultiplier (SiPMs) with 1004 cells, which themselves were optically isolated from each other n+ –p–p+ -structures. The cells were optically isolated from each other by trenches filled with tungsten after passivation of the walls with SiO2 and Si3N4 layers. Two variants of structural design of SiPMs were studied. Two variants were tested for the trench metal connection in the SiPMs: variant BI connected the trench metal to the n+-region of the cell through a quenching polysilicon resistor, while variant BII connected it to the p+-region. The breakdown voltage of the investigated SiPMs was Ubr = 34 ± 1.0 V. The samples were irradiated in both the active electrical mode (avalanche breakdown mode) and the passive mode (reverse bias Ub = 0 V). It was discovered, that at dose of D = 106 rad, the dark current for SiPM (BI) and (BII) increased by 6–7 times when irradiated in passive mode and by 15–16 times for SiPM (BII) when irradiated in active mode. For SiPM (BI) irradiated in the avalanche breakdown mode, the dark current increased by 104 times at D = 105 rad. The research demonstrates that the radiation-induced degradation of the dark current in the SiPMs under study is due to an increase in the generation and, primarily, surface components. This is a result of the accumulation of positive charge in the insulating layer of the separating trenches.

LArRI — A new setup for Liquid Argon Refractive index measurement

Liquid argon (LAr), widely used as the active target in neutrino and dark matter experiments, is a scintillator with a light yield of approximately 40 photons/keV. The scintillation spectrum is centered at 128 nm, and the attenuation length is of the order of meters, depending on the purity. The addition of small amounts of dopants allows for shifting the scintillation peak simplifying the light detection and opening the possibility to the development of imaging systems. There is no precise knowledge of the optical properties of LAr in the VUV range, but it could be exploited to improve the performances of liquid argon-based experiments, especially when the involved mass is in the ton scale. LArRI (Liquid Argon Refractive Index) aims to directly measure the refractive index of LAr in the VUV spectrum, using an interferometric technique. The refractive index is obtained by comparing two interference patterns, created in vacuum and liquid, acquired with cryogenic silicon photomultipliers. This work primarily presents the methodology, the preliminary tests, and the analysis strategy, which are intended to be applied to real data shortly.

SiPM-based LiDAR with multipulse sequence modulation and multithreshold signal processing.

A light detection and range technology (LiDAR) system that enables rapid ranging under extremely low signal-to-noise ratios (SNRs) during daylight conditions based on a SiPM (silicon photomultiplier) detector is proposed. The system emits a sequence of modulated laser pulses by controlling the semiconductor laser and then processes the SiPM response signals using dynamic multithreshold. The experimental result shows that, under extremely low SNR of daylight, the system achieves a 100% success rate in continuous ranging of a low reflectivity target at 125 m, with a ranging precision of less than 20 cm and a ranging time of less than 10 µs. Our system provides a significant reference value for achieving high-speed, noise-resistant, miniaturized, practical, and low-cost LiDAR based on a SiPM.

The CRILIN calorimeter: gamma radiation resistance of crystals and SiPMs

The Crilin calorimeter is a semi-homogeneous calorimetric system based on Lead Fluoride (PbF2) crystals with UV-extended Silicon Photomultipliers (SiPMs) proposed for the Muon Collider. This study investigates the radiation resistance of crystals and SiPMs, subjected to 10 kGy gamma irradiation, equivalent to a 10-year service life in the Muon Collider. Our findings indicate that while PbF2 crystals exhibit a decrease in transmittance post-irradiation with partial recovery over time, the alternative PbWO4-Ultra Fast (PWO-UF) demonstrates exceptional radiation hardness, maintaining stable transmittance. SiPMs showed an increase in dark current and breakdown voltage post-irradiation, with less degradation observed in the SiPM biased during the exposure to radiation compared to the unbiased component. These results underscore the viability of PbF2 for radiation-tolerant calorimeters, though improvements in production homogeneity are needed. The superior performance of PWO-UF crystals suggests they are a promising alternative for high-radiation applications, but their higher cost must be carefully considered.

4D-tracking with digital SiPMs

Silicon Photomultipliers (SiPMs) are the state-of-the-art technology in single-photon detection with solid-state detectors. Single Photon Avalanche Diodes (SPADs), the key element of SiPMs, can now be manufactured in CMOS processes, facilitating the integration of a SPAD array into custom monolithic ASICs. This allows implementing features such as signal digitization, masking, full hit-map readout, noise suppression, and photon counting in a monolithic CMOS chip. The complexity of the off-chip readout chain is thereby reduced.These new features allow new applications for digital SiPMs, such as 4D-tracking of charged particles, where spatial resolutions of the order of 10µm and timestamping with time resolutions of a few tens of ps are required.A prototype of a digital SiPM was designed at DESY using the LFoundry 150nm CMOS technology. Various studies were carried out in the laboratory and at the DESY II test-beam facility to evaluate the sensor performance in Minimum Ionizing Particles (MIPs) detection. The direct detection of charged particles was investigated for bare prototypes and assemblies coupling dSiPMs and thin LYSO crystals. Spatial resolution ∼20µm and a full-system time resolution of ∼50ps are measured using bare dSiPMs in direct MIP detection. Efficiency >99.5%, low noise rate and time resolution <1ns can be reached with the thin radiator coupling.

Measurement of muon flux behind the beam dump of the J-PARC Hadron Experimental Facility

A muon-flux measurement behind the beam dump of the J-PARC Hadron Experimental Facility was performed with a compact muon detector that can be inserted into a vertical observing hole with 81 mm in diameter which was dug underground. The detector consists of 12 plastic scintillation strips with a length of 80 mm each, which are arranged with cylindrical shape and contained inside an aluminum housing with an outer diameter of 75 mm. A silicon photomultiplier is coupled to the end of each strip to collect the scintillating light. The flux of the muons penetrating the beam dump was scanned vertically at intervals of 0.5 m, showing a wide distribution with a maximum at the beam level. The muon flux was consistent with the expectation from a Monte-Carlo simulation at more than 1 m away from the beam axis, which is expected to be used for signal-loss evaluation in the future KOTO II experiment for measuring rare kaon decays. The data can also be used in improving the accuracy of shielding calculations in the radiation protection.

Study on Characteristics of Epoxy Resin-Based Plastic Scintillators for Detectors with Simulation Using Monte Carlo Code

Abstract To determine the presence of radioactive materials emitting gamma rays entering or exiting nuclear facilities, ports, airports, international borders, or other strategic locations, radiation portal monitors (RPMs) capable of detecting such gamma radiation need to be installed in these places. National Research and Innovation Agency of Indonesia (BRIN) is currently developing RPMs with detector components made of plastic scintillator based on epoxy resin and augmented with aromatic fluorescent materials to produce visible light, which is the working range of the photomultiplier tube (PMT) or silicon photomultiplier (SiPM). This research aims to study the characteristics of the gamma photon radiation energy spectrum from Co-60, Cs-137, and Ir-192 sources in an epoxy resin plastic scintillator and study the absorbed dose of the scintillator to gamma photon radiation energy from Co-60, Cs-137, and Ir-192 sources as a function of source distance and incidence angle of gamma rays with simulations using the MCNPX code. The scintillator is modeled in the form of a cylinder with a diameter of 5 cm and a height of 5 cm. To simulate the gamma photon radiation energy spectrum in the scintillator, the F4 tally was used and to simulate the scintillator absorbed dose, the F6 tally was used. This simulation used gamma sources of Co-60, Cs-137, and Ir-192 of 1 mCi each. These characteristics of the epoxy resin plastic scintillator have been successfully simulated. Data on the characteristics of epoxy resin plastic scintillators is important to know and study as supporting data in making plastic detectors as part of the manufacture and development of RPM.

Studies of GAGG:Ce scintillators for space missions dedicated to Terrestrial Gamma-Ray Flashes and Gamma-Ray Bursts observation

Fast Gamma ray Spectrometer (FGS) is an on-going detector development for the observation of transient gamma ray events such as Terrestrial Gamma ray Flashes (TGFs) produced in Earth’s thunderstorms and Gamma Ray Bursts (GRBs) produced in the far Universe. In this work, we compare different Cerium-doped Gadolinium Aluminium Gallium Garnet (GAGG:Ce) scintillators, associated with Silicon Photo-Multipliers (SiPMs), quantifying their performances at atmospheric pressure and under vacuum, with different surface finitions. We also study their afterglow following proton irradiation, similar to what will be observed in space environment. Our measurements with GAGG:Ce scintillators after proton irradiation confirm that GAGG:Ce can be used in space.

New readout system of the FATIMA detectors based on Silicon Photomultipliers arrays

We present a new readout system based on large area Silicon Photomultipliers arrays coupled with cylindrical 1.5 × 2” LaBr3(Ce) FATIMA-type crystals. This achieves the fast-timing capabilities of such crystals coupled to the usual Photomultiplier Tubes. Energy calibration was measured with 137Cs and 152Eu standard radioactive sources, while the timing performances were investigated with a 60Co radioactive source. We benchmark our results against the corresponding results obtained with the fast R9779 Photomultiplier tubes and highlight the importance of achieving similar energy and timing performances for nuclear structure experiments. The FWHM energy resolution for the 1.5 × 2” LaBr3(Ce) crystal coupled with the SiPM and PMT was found to be 3.31(2)% and 3.85(1)%, respectively, for the 661.6 keV transition of the 137Cs source. The timing resolution was measured between a conical crystal known for its fast response and a cylindrical crystal coupled to a SiPM or PMT readout. We obtain values of FWHM = 230(1) ps and 232(1) ps, respectively, between the 1173.2-1332.5 keV transitions of the 60Co source. In addition, a temperature effect compensation circuit was developed to maintain a good stability of the gain during long measurements, typical for in-beam/off-beam experiments in nuclear physics.

Application of the VMM ASIC for SiPM-based calorimetry

Highly integrated multichannel readout electronics is crucial in contemporary particle physics experiments. A novel silicon photomultiplier readout system based on the VMM3a ASIC was developed, for the first time exploiting this chip for calorimetric purposes. To extend the dynamic range the signal from each SiPM channel was processed by two electronics channels with different gain. A fully operational prototype system with 256 SiPM readout channels allowed the collection of data from a prototype of the ALICE Forward Hadron Calorimeter (FoCal-H Prototype 2). The design and the test beam results using high energy hadron beams are presented and discussed, confirming the applicability of VMM3a-based solutions for energy measurements in a high rate environment.

Developing an alternative calorimeter solution for the future Muon Collider: The Crilin design

The Crilin calorimeter represents a novel approach in the development of electromagnetic calorimeters for future colliders, especially for a Muon Collider. This paper details the design and performance of the innovative semi-homogeneous Crilin calorimeter, highlighting its capabilities in mitigating beam-induced backgrounds (BIB) while maintaining excellent time resolution (less than 50 ps), longitudinal segmentation, and fine granularity. These performances are achieved throughout a series of stackable and interchangeable lead fluoride (PbF2) crystal matrices readout by surface-mount UV-extended Silicon Photo-multipliers. Simulated and experimental results demonstrate the Crilin design’s potential to work as an efficient and cost-effective alternative to traditional electromagnetic calorimeters. Crilin radiation tolerance is discussed, as measured in several irradiation campaigns, as well as timing performances during a beam test at CERN-H2 with 120 GeV electrons for the latest prototype, Proto-1. Additionally, a description of the results from a recent beam test conducted at the LNF Beam Test Facility with 450 MeV electrons is provided, aiming to measure light yield losses due to irradiation.

Feasibility study of YSO/SiPM based detectors for virtual monochromatic image synthesis.

The development of photon-counting CT systems has focused on semiconductor detectors like cadmium zinc telluride (CZT) and cadmium telluride (CdTe). However, these detectors face high costs and charge-sharing issues, distorting the energy spectrum. Indirect detection using Yttrium Orthosilicate (YSO) scintillators with silicon photomultiplier (SiPM) offers a cost-effective alternative with high detection efficiency, low dark count rate, and high sensor gain. This work aims to demonstrate the feasibility of the YSO/SiPM detector (DexScanner L103) based on the Multi-Voltage Threshold (MVT) sampling method as a photon-counting CT detector by evaluating the synthesis error of virtual monochromatic images. In this study, we developed a proof-of-concept benchtop photon-counting CT system, and employed a direct method for empirical virtual monochromatic image synthesis (EVMIS) by polynomial fitting under the principle of least square deviation without X-ray spectral information. The accuracy of the empirical energy calibration techniques was evaluated by comparing the reconstructed and actual attenuation coefficients of calibration and test materials using mean relative error (MRE) and mean square error (MSE). In dual-material imaging experiments, the overall average synthesis error for three monoenergetic images of distinct materials is 2.53% ±2.43%. Similarly, in K-edge imaging experiments encompassing four materials, the overall average synthesis error for three monoenergetic images is 4.04% ±2.63%. In rat biological soft-tissue imaging experiments, we further predicted the densities of various rat tissues as follows: bone density is 1.41±0.07 g/cm3, adipose tissue density is 0.91±0.06 g/cm3, heart tissue density is 1.09±0.04 g/cm3, and lung tissue density is 0.32±0.07 g/cm3. Those results showed that the reconstructed virtual monochromatic images had good conformance for each material. This study indicates the SiPM-based photon-counting detector could be used for monochromatic image synthesis and is a promising method for developing spectral computed tomography systems.

Characterization of neutron-irradiated SiPMs down to liquid nitrogen temperature

Photodetectors used in future high-energy physics experiments will need to keep sufficient performance during a few years of data-taking despite radiation load, which, for example, in the planned upgrade of the Ring Imaging Cherenkov detectors in Large Hadron Collider beauty (LHCb) experiment is estimated at about 1013\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{13}$$\\end{document} 1-MeV neutron equivalent per cm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{2}$$\\end{document} (neq/cm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{2}$$\\end{document}). Silicon photomultipliers (SiPMs) are considered as candidates for photodetectors for this application. However, their sensitivity to neutron irradiation may seriously compromise their operation, with the increase in dark count rates being the primary limitation after the irradiation. In this work, 1 ×\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\ imes $$\\end{document} 1 mm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{2}$$\\end{document} 15 μ\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\mu $$\\end{document}m pitch NUV-HD-RH silicon photomultipliers developed by the Fondazione Bruno Kessler were characterized before and after the irradiation. In total, 5 SiPMs were irradiated at the Jožef Stefan Institute TRIGA nuclear reactor with different fluences from 109\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{9}$$\\end{document} neq/cm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{2}$$\\end{document} up to 1013\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{13}$$\\end{document} neq/cm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{2}$$\\end{document}. The SiPMs were also annealed at high temperatures and re-characterized after the annealing. For the SiPM characterization in all the cases, current–voltage (I-V curve) measurements, dark count rate measurements, and waveform analysis, including single photon time resolution, were carried out at different controlled temperature steps from room temperature down to the liquid nitrogen temperature. While cooling to − 20∘\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{\\circ }$$\\end{document}C was enough for the SiPM irradiated at 109\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{9}$$\\end{document} neq/cm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{2}$$\\end{document} to recover the ability to resolve single photons, by 1013\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{13}$$\\end{document} neq/cm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{2}$$\\end{document}, cooling to liquid nitrogen temperature was necessary. With sufficient cooling, the measured single photon time resolution was around 90 ps FWHM for all irradiation levels.

Assessing a binary quantum channel exploiting a Silicon photomultiplier based hybrid receiver

Assessing a binary quantum channel exploiting a Silicon photomultiplier based hybrid receiver

Improving Compton camera imaging of multi-energy radioactive sources by using machine learning algorithms for event selection

Event selection and background reduction for Compton camera imaging of multi-energy radioactive sources has been performed by employing neural networks. A Compton camera prototype with detectors made of LaBr3 crystals coupled to silicon photomultiplier arrays was used to acquire experimental data from a circular array of 22Na sources. The prototype and two arrays of 22Na sources were simulated with GATE v8.2 Monte Carlo code, to obtain data for neural network training. Neural network models were trained on simulated data for event classification. The optimum models were found by using Weights & Biases platform tools. The trained models were used to classify simulated and real data for selecting signal events and rejecting background prior to image reconstruction. The models performed well on simulated data. The image obtained with experimental data showed an improvement with respect to event selection with energy cuts. The method is promising for Compton camera imaging of multi-energy radioactive sources.

Optimization of the Pixel Design for Large Gamma Cameras Based on Silicon Photomultipliers.

Most single-photon emission computed tomography (SPECT) scanners employ a gamma camera with a large scintillator crystal and 50-100 large photomultiplier tubes (PMTs). In the past, we proposed that the weight, size and cost of a scanner could be reduced by replacing the PMTs with large-area silicon photomultiplier (SiPM) pixels in which commercial SiPMs are summed to reduce the number of readout channels. We studied the feasibility of that solution with a small homemade camera, but the question on how it could be implemented in a large camera remained open. In this work, we try to answer this question by performing Geant4 simulations of a full-body SPECT camera. We studied how the pixel size, shape and noise could affect its energy and spatial resolution. Our results suggest that it would be possible to obtain an intrinsic spatial resolution of a few mm FWHM and an energy resolution at 140 keV close to 10%, even if using pixels more than 20 times larger than standard commercial SiPMs of 6 × 6 mm2. We have also found that if SiPMs are distributed following a honeycomb structure, the spatial resolution is significantly better than if using square pixels distributed in a square grid.

Measurement of energy resolution with the NEXT-White silicon photomultipliers

The NEXT-White detector, a high-pressure gaseous xenon time projection chamber, demonstrated the excellence of this technology for future neutrinoless double beta decay searches using photomultiplier tubes (PMTs) to measure energy and silicon photomultipliers (SiPMs) to extract topology information. This analysis uses 83mKr data from the NEXT-White detector to measure and understand the energy resolution that can be obtained with the SiPMs, rather than with PMTs. The energy resolution obtained of (10.9 ± 0.6)%, full-width half-maximum, is slightly larger than predicted based on the photon statistics resulting from very low light detection coverage of the SiPM plane in the NEXT-White detector. The difference in the predicted and measured resolution is attributed to poor corrections, which are expected to be improved with larger statistics. Furthermore, the noise of the SiPMs is shown to not be a dominant factor in the energy resolution and may be negligible when noise subtraction is applied appropriately, for high-energy events or larger SiPM coverage detectors. These results, which are extrapolated to estimate the response of large coverage SiPM planes, are promising for the development of future, SiPM-only, readout planes that can offer imaging and achieve similar energy resolution to that previously demonstrated with PMTs.