Side-emitting Optical Fibers Research Articles

Triple Spectral Line Imaging of Whole-Body Human Skin: Equipment, Image Processing, and Clinical Data.

Multispectral imaging can provide objective quantitative data on various clinical pathologies, e.g., abnormal content of bio-substances in human skin. Performance of diagnostics increases with decreased spectral bandwidths of imaging; from this point, ultra-narrowband laser spectral line imaging is well suited for diagnostic applications. In this study, 40 volunteers participated in clinical validation tests of a newly developed prototype device for triple laser line whole-body skin imaging. The device comprised a vertically movable high-resolution camera coupled with a specific illumination unit-a side-emitting optical fiber spiral that emits simultaneously three RGB laser spectral lines at the wavelengths 450 nm, 520 nm, and 628 nm. The prototype's design details, skin spectral image processing, and the obtained first clinical data are reported and discussed.

Silver nanoparticle-decorated reduced graphene oxide/ nanocrystalline titanium metal-organic frameworks composite membranes with enhanced nanofiltration performance and photocatalytic ability

Nanofiltration (NF) has garnered significant attention for removing persistent dyes from industrial wastewater. However, limited membrane separation efficiency and performance deterioration due to membrane fouling are the primary challenges hindering the broader application of NF technology. Herein, we developed high-performance silver nanoparticle-coated reduced graphene oxide/nanocrystalline MIL125(Ti) composite NF membranes (nAg-rGO/n-MIL), which feature self-cleaning capabilities through photocatalytic activity. This was achieved by intercalating nanocrystalline MIL-125(Ti) (n-MIL) metal-organic frameworks between graphene oxide (GO) nanosheets, followed by reducing the GO nanosheets and decorating them with silver nanoparticles (nAg) via UV exposure. The nAg-rGO/n-MIL demonstrated high water permeability (21.7 LMH/bar) and achieved excellent removal efficiencies for targeting dyes with relatively small molecular weights ranging from 300 to 500 Da. Additionally, when operated in an NF system equipped with a UV side-emitting optical fiber, the nAg-rGO/n-MIL exhibited significantly reduced water flux decline and enhanced removal efficiencies, achieving up to 97.5 % for methylene blue. Moreover, the nAg-rGO/n-MIL demonstrated high durability under the tested operating conditions, indicating its potential for long-term use in industrial applications. The GO composite membrane, with nanosized MOF-intercalated nanochannels and photocatalytic activity via nAg decoration and GO reduction, offers a promising solution to performance limitations and fouling issues in current nanofiltration membranes.

Experimental evaluation of wearable LED strip and side-emitting fiber for optical camera communications systems.

This paper presents an experimental evaluation of two types of light-emitting diode (LED)-based distributed transmitters, namely an LED strip and an LED-coupled side-emitting optical fiber, in both laboratory and wearable optical camera communication (OCC) systems. We study the system performance in terms of success of reception (SoR) with regard to the transmission distance. The best value of SoR is achieved when the camera is facing directly to the transmitter (Tx) from a close distance of 1 m. Additionally, we compare the power consumption, the signal-to-noise ratio performance (SNR) and all the obtained values under optimal conditions are better than the forward error correction (FEC) limit in OCC systems.

UV-C side-emitting optical fiber-based disinfection: a promising approach for infection control in tight channels.

The growth of pathogenic bacteria in moist and wet surfaces and tubing of medically relevant devices results in serious infections in immunocompromised patients. In this study, we investigated and demonstrated the successful implementation of a UV-C side-emitting optical fiber in disinfecting medically relevant pathogenic bacteria (Pseudomonas aeruginosa and Methicillin-resistant Staphylococcus aureus [MRSA]) within tight channels of polytetrafluoroethylene (PTFE). PTFE is a commonly used material both in point-of-use (POU) water treatment technologies and medical devices (dental unit water line [DUWL], endoscope). For a 1-m-long PTFE channel, up to ≥6 log inactivation was achieved using a 1-m-long UV side-emitting optical fiber (SEOF) with continuous 16-h exposure of low UV-C radiation ranging from ~0.23 to ~29.30 μW/cm2. Furthermore, a linear model was used to calculate the inhibition zone constant (k`), which enables us to establish a correlation between UV dosage and the extent of inactivated surface area (cm2) for surface-bound Escherichia coli on a nutrient-rich medium. The k` value for an irradiance ranging from ~150 to ~271.50 μW/cm2 was calculated to be 0.564 ± 0.6 cm·cm2/mJ. This study demonstrated the efficacy of SEOFs for disinfection of medically relevant microorganisms present in medically and domestically relevant tight channels. The impact of the results in this study extends to the optimization of operational efficiency in pre-existing UV surface disinfection setups that currently operate at UV dosages exceeding the optimal levels.IMPORTANCEGermicidal UV radiation has gained global recognition for its effectiveness in water and surface disinfection. Recently, various works have illustrated the benefit of using UV-C side-emitting optical fibers (SEOFs) for the disinfection of tight polytetrafluoroethylene (PTFE) channels. This study now demonstrates its impact for disinfection of medically relevant organisms and introduces critical design calculations needed for its implementation. The flexible geometry and controlled emission of light in these UV-SEOFs make them ideal for light distribution in tight channels. Moreover, the results presented in this manuscript provide a novel framework that can be employed in various applications, addressing microbial contamination and the disinfection of tight channels.

Side-emitting fiber-based distributed receiver for visible light communication uplink.

We present a distributed receiver for visible light communication based on a side-emitting optical fiber. We show that 500 kbps data rate can be captured with a bit-error rate below the forward-error correction limit of 3.8·10-3 with a light-emitting diode (LED) transmitter 25 cm away from the fiber, whereas by increasing the photodetector gain and reducing the data rate down to 50 kbps, we improve the LED-fiber distance significantly up to 4 m. Our results lead to a low-cost distributed visible-light receiver with a 360° field of view for indoor low-data rate, Internet of Things, and sensory networks.

Subtractive Engineering of Polymer Cladding Induces Tunable UV-C Irradiation from Flexible Side-Emitting Optical Fibers for Biofilm Control in Curved Piping

Subtractive Engineering of Polymer Cladding Induces Tunable UV-C Irradiation from Flexible Side-Emitting Optical Fibers for Biofilm Control in Curved Piping

Phenotypic and Transcriptional Responses of Pseudomonas aeruginosa Biofilms to UV-C Irradiation via Side-Emitting Optical Fibers: Implications for Biofouling Control.

Biofilms give rise to a range of issues, spanning from harboring pathogens to accelerating microbial-induced corrosion in pressurized water systems. Introducing germicidal UV-C (200-280 nm) irradiation from light-emitting diodes (LEDs) into flexible side-emitting optical fibers (SEOFs) presents a novel light delivery method to inhibit the accumulation of biofilms on surfaces found in small-diameter tubing or other intricate geometries. This work used surfaces fully submerged in flowing water that contained Pseudomonas aeruginosa, an opportunistic pathogen commonly found in water system biofilms. A SEOF delivered a UV-C gradient to the surface for biofilm inhibition. Biofilm growth over time was monitored in situ using optical conference tomography. Biofilm formation was effectively inhibited when the 275 nm UV-C irradiance was ≥8 μW/cm2. Biofilm samples were collected from several regions on the surface, representing low and high UV-C irradiance. RNA sequencing of these samples revealed that high UV-C irradiance inhibited the expression of functional genes related to energy metabolism, DNA repair, quorum sensing, polysaccharide production, and mobility. However, insufficient sublethal UV-C exposure led to upregulation genes for SOS response and quorum sensing as survival strategies against the UV-C stress. These results underscore the need to maintain minimum UV-C exposure on surfaces to effectively inhibit biofilm formation in water systems.

Inhibition of biofouling on reverse osmosis membrane surfaces by germicidal ultraviolet light side-emitting optical fibers

Biofouling of membrane surfaces poses significant operational challenges and costs for desalination and wastewater reuse applications. Ultraviolet (UV) light can control biofilms while reducing chemical usage and disinfection by-products, but light deliveries to membrane surfaces in spiral wound geometries has been a daunting challenge. Thin and flexible nano-enabled side-emitting optical fibers (SEOFs) are novel light delivery devices that enable disinfection or photocatalytic oxidation by radiating UV light from light-emitting diodes (LEDs). We envision SEOFs as an active membrane spacer to mitigate biofilm formation on reverse osmosis (RO) membranes. A lab-scale RO membrane apparatus equipped with SEOFs allowed comparison of UV-A (photocatalysis-enabled) versus UV-C (direct photolysis disinfection). Compared against systems without any light exposure, systems with UV-C light formed thinner—but denser—biofilms, prevented permeate flux declines due to biofouling, and maintained the highest salt rejection. Results were corroborated by in-situ optical coherence tomography and ex-situ measurements of biofilm growth on the membranes. Transcriptomic analysis showed that UV-C SEOFs down-regulated quorum sensing and surface attachment genes. In contrast, UV-A SEOFs upregulated quorum sensing, surface attachment, and oxidative stress genes, resulting in higher extracellular polymeric substances (EPS) accumulation on membrane surfaces. Overall, SEOFs that deliver a low fluence of UV-C light onto membrane surfaces are a promising non-chemical approach for mitigating biofouling formation on RO membranes.

Non-resonant luminescence enhancement in sol-gel coatings for broadband UV-light conversion on side-emitting optical fibers

Photoluminescence (PL) is a key mechanism for many light conversion applications but often provides only low yield and poor efficiency due to a small interaction cross-section and a relatively narrow range of spectral activity. Here, we present a simple technique to enhance the PL of europium(III) (Eu3+) from sol-gel coatings on the surface of a side-emitting optical fiber. We use small clusters of Ag to boost the emission of Eu3+ by an energy transfer mechanism. The coating's performance is studied as a function of Ag concentration and annealing time. We report a substantial enhancement in Eu3+ emission under resonant and non-resonant excitation with UV light. However, this enhancement vanishes when the Ag clusters grow into larger nanoparticles with plasmon activity: we demonstrate that silver clusters produce stronger amplification with a broader excitation range than metallic nanoparticles. Moreover, these clusters are easily generated and stabilized in a coating using standard sol-gel techniques, suitable for deposition on the surface of side-emitting fibers. Such fibers can then be employed as line-shaped emitters, for example, for structured illumination purposes.

Weaving light - [Past Forward

Textile artist Suzanne Tick is known for incorporating unusual materials into her weaving: recycled dry cleaner hangers, Mylar balloons washed up on the beach, documents from her divorce. For this work, called Crossform Pendant Lamp, she used industrial fiber-optic yarn, a technology that was more than 150 years in the making. Back in 1841, the Swiss physicist Jean-Daniel Colladon first demonstrated that light could travel along a curved path defined by a stream of water; in 1960, Narinder Singh Kapany coined the term "fiber optics"; and 50 years ago this month, engineers at Corning demonstrated low-loss optical fiber. Tick combines in her sculpture 21st-century side-emitting optical fibers with the millennia-old practice of weaving to allow her lamp to glow from within.

Germicidal glowsticks: Side-emitting optical fibers inhibit Pseudomonas aeruginosa and Escherichia coli on surfaces

This paper investigates using UV-C side-emitting optical fibers (SEOFs) to prevent growth of pathogenic bacteria (Pseudomonas aeruginosa and Escherichia coli) on nutrient-rich surfaces. Attaching a SEOF to a single 265 nm light emitting diode (LED) increases irradiation area by >1000x and provides continuous low-irradiance of UV-C light to a large surface area. A zone-of-inhibition protocol was developed to quantify bacterial growth prevention on an agar plate around one SEOF. The inhibition zone increased linearly with irradiance time until achieving a maximum inhibition zone of 2.5 to 3 cm, which received ~ 4.3 mJ/cm2 of 265 nm light in 2 hours. The surviving lawn edge bacterial colonies did not develop UV resistance after two generations of exposure. The agar plate remained bio-available after UV exposure, and bacteria could be grown on pre-illuminated area in the absence of UV-C light. Whereas we previously demonstrated SEOFs can inactivate planktonic bacteria, herein we show the ability of SEOFs to prevent bacteria growth on surfaces. This is the first step towards developing technologies with multiple SEOFs to inhibit biofilm growth on surfaces, which is a ubiquitous challenge across multiple applications from membrane surfaces to surfaces in pipes or water storage systems.

Textile Based Three-Layer Robust Flexible and Stable Electrochromic Display

The textile-based electrochromic (EC) display which has been developed and presented in this article, is very compact, robust, flexible, stable, efficient, economical, and inclined to biocompatibility. The developed textile display is having only three-layer over conventional seven layers patented electrochromic structures. It is also very efficient, as it can perform its functionality even after 2500 cycles of a run and 1500 times of bending. The innovative and simplified structure of the EC device has been developed with only 3 layers, including the displaying electrode, the electrolyte container, and the counter electrode. The conductive polymer PEDOT:PSS used here as a conductive and electrochromic material, is coated on the textile substrate to perform as one side of the electrode for the asymmetric arrangement of the electrochromic device. The experiment has also been done to find out the best possible textile fabric to serve as the optimal electrochromic container. The biocompatible H3PO4 gel drenched in the semi-permeable membrane has been used as an ion transfer medium for the electrochromic display. This biocompatible ion transfer medium is sandwiched in between the electrochromic displaying electrode (PEDOT:PSS coated on fabric) and aluminum sheet (counter electrode) for making this handmade crude electrochromic display. The investigation of the EC display functioning has been observed through cyclic voltammetry within the life cycle run. The performance of the device has also been investigated in real-life conditions, by providing just ±2.0 V DC power. The other possibility is shown in our article to deposit the PEDOT:PSS compound on the textile substrate was to coat directly the yarns and then to use them into the weaving process to produce the displaying electrode. By this technique, it would also be possible to develop hybrid displays made of structures containing knitted or woven side-emitting optical fibers and our electrochromic display structure, locally.

Nanoparticle and Transparent Polymer Coatings Enable UV-C Side-Emission Optical Fibers for Inactivation of Escherichia coli in Water.

Pathogenic bacteria pose a health threat and operational challenge in drinking water. UV-C light-emitting diodes (UV-C LEDs) are becoming a competitive disinfection technology but are limited by their small irradiation area. Side-emitting optical fibers (SEOFs) can serve as a UV-C LED light delivery technology for reactors or tubing. Modifying the surfaces of conventional optical fibers with scattering centers allows for side emission of 265 nm radiation from an LED for microbial inactivation in water. Solid-material absorbance and flux measurements differentiated light absorption from scattering for all materials. Silica spheres >200 nm in diameter achieved higher scattering than smaller silica. A critical discovery was that treating the silica-coated optical fiber in a solution of high ionic strength increased UV-C side emission by greater than 6-fold. Additionally, the cladding polymer Cytop had negligible absorbance at 265 nm wavelength. A scalable four-step treatment process was developed to fabricate the novel SEOF. Attached to a 265 nm LED, the side-emitting optical fiber achieved 2.9 log inactivation of Escherichia coli at a delivery dose of 15 mJ/cm2. The results illustrate proof of concept that UV-C SEOFs can inactivate E. coli and should be further explored for delivering LED light into water.

Biomimetic light dilution using side-emitting optical fiber for enhancing the productivity of microalgae reactors

Photoautotrophic microbes present vast opportunities for sustainable lipid production, CO2 storage and green chemistry, for example, using microalgae beds to generate biofuels. A major challenge of microalgae cultivation and other photochemical reactors is the efficiency of light delivery. In order to break even on large scale, dedicated photon management will be required across all levels of reactor hierarchy – from the harvesting of light and its efficient injection and distribution inside of the reactor to the design of optical antenna and pathways of energy transfer on molecular scale. Here, we discuss a biomimetic approach for light dilution which enables homogeneous illumination of large reactor volumes with high optical density. We show that the immersion of side-emitting optical fiber within the reactor can enhance the fraction of illuminated volume by more than two orders of magnitude already at cell densities as low as ~5 104 ml−1. Using the green algae Haematococcus pluvialis as a model system, we demonstrate an increase in the rate of reproduction by up to 93%. Beyond micoralgae, the versatile properties of side-emitting fiber enable the injection and dilution of light with tailored spectral and temporal characteristics into virtually any reactor containment.

A Colorimetric Multifunctional Sensing Method for Structural-Durability-Health Monitoring Systems.

A colorimetric multifunctional phototransmittance-based structural durability monitoring system is developed. The system consists of an array with four indium gallium zinc oxide (IGZO)-based phototransistors, a light source at a wavelength of 405 nm through a side-emitting optical fiber, and pH- and Cl-selective color-variable membranes. Under illumination at the wavelength of 405 nm at corrosion status, the pH- and Cl-responsive membrane, showing a change in their color, generates a change in the intensity of the transmitted light, which is received by the phototransistor array in the form of an electrical current. Ids and R (Ids /IpH 12 ) are inversely proportional to the pH, which ranges from 10 to 12. When the pH drops from 12 to 10, the magnitude of Ids and R increases to ≈103 . In the case of Cl detection, Ids and R (Ids /ICl 0 wt% ) increase nearly 50 times with an increase in Cl concentration of 0.05 wt%, and when the Cl concentration reaches 0.30 wt%, Ids and R increase to ≈103 times greater. This multifunctional colorimetric durability sensing system demonstrates considerable potential as a novel smart-diagnostic tool of structural durability with high stability, high sensitivity, and multifunction.

Pressure in the Cochlea During Infrared Irradiation.

The purpose of the study is to demonstrate laser-evoked pressure waves in small confined volumes such as the cochlea. Custom-fabricated pressure probes were used to determine the pressure in front of the optical fiber in a small dish and patch pipettes to measure temperature changes. Pressure probes were inserted into scala tympani (ST) or vestibuli during laser stimulation. With a sensitive microphone the pressure was measured in the outer ear canal. Heating was spatially confined. The heat relaxation time was 35 ms. During laser stimulation in the cochlea at 17 μJ/pulse, the pressure in the outer ear canal (EC) was 43.5 dB (re 20 μPa). The corresponding intracochlear pressure was calculated to be about 78.5 dB (re 20 μPa) using the middle ear reverse transfer function of -35 dB. At 164 μJ/pulse, the pressure in the EC was on average 63 dB (re 20 μPa) and the intracochlear pressure was estimated to be 98 dB (re 20 μPa), which is similar to the value obtained with the pressure probe, 100 dB (re 20 μPa). Side-emitting optical fibers were used to steer the beam path. The pressure values were independent of the orientation of the beam path. Evoked compound action potentials of the auditory nerve were maximum when spiral ganglion neurons were in the beam path. Pressure waves are generated during infrared laser stimulation. The intracochlear pressure was independent from the orientation of the beam path. Neural responses required the spiral ganglion neurons to be directly irradiated.

Light emitting fabric technologies for photodynamic therapy

Photodynamic therapy (PDT) is considered to be a promising method for treating various types of cancer. A homogeneous and reproducible illumination during clinical PDT plays a determinant role in preventing under- or over-treatment. The development of flexible light sources would considerably improve the homogeneity of light delivery. The integration of optical fiber into flexible structures could offer an interesting alternative. This paper aims to describe different methods proposed to develop Side Emitting Optical Fibers (SEOF), and how these SEOF can be integrated in a flexible structure to improve light illumination of the skin during PDT. Four main techniques can be described: (i) light blanket integrating side-glowing optical fibers, (ii) light emitting panel composed of SEOF obtained by micro-perforations of the cladding, (iii) embroidery-based light emitting fabric, and (iv) woven-based light emitting fabric. Woven-based light emitting fabrics give the best performances: higher fluence rate, best homogeneity of light delivery, good flexibility.

The Design of Jacquard Fabric with Optical Fiber for Effect of Leaves Falling

The optical jacquard decorative fabric which had patterns in dynamic display was woven with side-emitting polymer optical fibers (POF) and common textile fibers. The side-emitting POFs were designed as surface wefts in luminous parts of the fabric, and the POFs were back in other parts. These POFs were divided into different groups according to luminous sequence. Then the POFs were connected with light sources and a specific circuit. Finally the patterns of fabric could display like animation. When POFs didnt emit light, the fabric kept the effect of traditional jacquard fabric.

Novel light-leaking optical fiber liquid-level sensor for aircraft fuel gauging

We present a novel light leaking optical fiber liquid level sensor for aircraft fuel measuring systems that is based on the side-emitting optical fiber. In operation, the fiber is bent as a spiral and inserted into the liquid, then the conducting light in the fiber will be scattered and transformed to be cladding mode and radiation mode. The radiation mode power in the scattering light is determined by the ambient refractive index. Since more power is lost in liquids than in the air, the output power of the sensor will monotonically decrease while the liquid level increases. The fiber is bent as a spiral to increase the sensor’s sensitivity. A laboratory prototype with a range of 1 m, a radius of 14 mm, and a screw pitch of 15 mm has been built and successfully demonstrated in water level measurement. The sensor’s response to liquid level is presented and shown to be consistent with the theory.

Continuous Fuel Level Sensor Based on Spiral Side-Emitting Optical Fiber

A continuous fuel level sensor using a side-emitting optical fiber is introduced in this paper. This sensor operates on the modulation of the light intensity in fiber, which is caused by the cladding’s acceptance angle change when it is immersed in fuel. The fiber is bent as a spiral shape to increase the sensor’s sensitivity by increasing the attenuation coefficient and fiber’s submerged length compared to liquid level. The attenuation coefficients of fiber with different bent radiuses in the air and water are acquired through experiments. The fiber is designed as a spiral shape with a steadily changing slope, and its response to water level is simulated. The experimental results taken in water and aviation kerosene demonstrate a performance of 0.9 m range and 10 mm resolution.