Series Connection Research Articles

High-performance supercapacitor of ZnO-incorporated structurally modified g-C3N4 with circular mesoporous channels attained via a template-free approach

Abstract Here, the superior structural features of graphitic carbon nitride (g-C3N4) in combination with integrated mesoporous channels have been explored for its use as a supercapacitor electrode material. A facile template-free strategy is adopted for the preparation of ZnO-incorporated modified g-C3N4 nanocomposite, where material characterization via x-ray difraction, Fourier transfrom infrared spectroscopy, field-emission scanning electron microscopy, transmission electron microscopy and x-ray photoelectron spectroscopy analysis revealed the presence of structurally modified g-C3N4 having uniform circular mesoporous channels with well-dispersed ZnO with strong Zn–C and Zn–N interactions. The electrical double-layer capacitance together with the pseudocapacitance of the ZnO/g-C3N4 electrode material resulted in improved performance, leading to a specific capacitance of 146.3 F g−1 at a current density of 0.5 A g−1; an increased capacitance is observed in 5000 repeated charge–discharge cycles. A symmetric coin cell supercapacitor fabricated from the material displayed an energy density of 38.8 mWh kg−1 at a power density of 4259 mW kg−1. Additionally, the long life of 6000 cycles (retaining 100% specific capacitance) exhibited by the coin cell supercapacitor further indicates the promising energy storage nature of the ZnO-incorporated modified g-C3N4 mesoporous nanoarchitecture. Real life application of the ZnO/g-C3N4-derived supercapacitor is illustrated by lighting up a green LED with a series connection of four coin cells.

ISOS-SAB DC/DC Converter for Large-Capacity Offshore Wind Turbine

This study offers a modular isolated grid-connected DC/DC medium-voltage DC aggregation converter to support offshore full DC wind farms’ need for lightweight and highly efficient power aggregation and transmission. The converter can simultaneously have a smaller transformer size and lower switching frequency during operation through the dual-voltage stabilization three-loop control strategy and phase-shift modulation strategy, which greatly reduces the space occupied by the converter and lowers the switching loss, Additionally, the use of a two-level structure at a lower switching frequency has lower loss, which effectively reduces the cost of the power device compared with the commonly used three-level converter. The input series output series connection between the converter sub-modules effectively lowers the voltage stress on each power switching device and facilitates expansion into a multi-module structure, expanding its application in high-voltage and large-capacity environments. This study analyzes the two working modes of the DC/DC converter and its control approach, in addition to providing a detailed introduction to the application scenarios of this converter. Ultimately, the efficacy and practicability of the suggested topology and control scheme are confirmed by simulations and experiments.

Simulation Study on Factors Affecting the Output Voltage of Extended-Range Electric Vehicle Power Batteries

The power battery configuration of an extended-range electric vehicle directly affects the overall performance of the vehicle. Optimization of the output voltage of the power battery can improve the overall power and economy of the vehicle to ensure its safe operation. Factors affecting the output voltage of power batteries under different operating conditions, such as nominal voltage and the number of series and parallel connections of the battery cells, have been studied. This study uses AVL Cruise to establish an overall model of an extended-range electric vehicle to simulate the output voltage characteristics under the different operating conditions of the NEDC (New European Driving Cycle), WLTC (World Light Vehicle Test Cycle) and CLTC (China Light Duty Vehicle Test Cycle). The influence of the output voltage of the power battery under different operating conditions is studied to ensure that the power battery can output energy with high efficiency. The operating conditions have an impact on the output voltage with an idle voltage fluctuation of the operating conditions. The nominal voltage variation and the number of series and parallel connections of the battery cells affect the frequency and time of breakdown.

Fabrication and performance evaluation of large–scale luminescent and plasmonic luminescent solar concentrator modules

This study presents the detailed fabrication and performance evaluation of large–scale luminescent solar concentrator (LSC) and plasmonic luminescent solar concentrator (PLSC) modules. Individual LSC, PLSC, and reference devices have been fabricated with dimensions of 10 x 10 x 0.5 cm. Five devices of each type were connected in series, ensuring correct photovoltaic cell polarity, to form cohesive modular groups with minimal mismatch. These solar concentrators were subsequently integrated into an outdoor panel designed to accommodate the modules for outdoor performance evaluations. Outputs of 240 mW, 213 mW, and 46 mW were observed for the individual PLSC, LSC and reference devices respectively from an indoor solar simulator test outputting 900 W/m2. Outdoor performance analysis has highlighted that the inclusion of metal nanoparticles within the PLSCs enhanced the outputs by 65% on average with a maximum enhancement of 88.6% observed over the course of a single day. The series connection within the LSC modules demonstrated enhanced scalability and potential for practical application in solar energy systems. This innovative module configuration provides valuable insights into the advancement of luminescent solar concentrators through plasmonic enhancement, contributing to the broader goal of optimising solar energy harvesting.

High-performance and ultra-robust triboelectric nanogenerator based on hBN nanosheets/PVDF composite membranes for wind energy harvesting

Triboelectric nanogenerator (TENG) is a novel energy technology that converts high-entropy mechanical energy from the environment into electrical energy using triboelectrification and electrostatic induction effects. However, the low surface charge density and easy wear of traditional triboelectric materials are bottlenecks for their practical applications. Here, a remarkable triboelectric properties, superior mechanical properties, exceptional wear resistance, and high thermal conductivity hexagonal boron nitride nanosheets (hBNNS)/ polyvinylidene difluoride (PVDF) composite negative triboelectric material is developed. The inclusion of hBNNS as an electron acceptor and nucleating agent not only effectively boosted the surface charge density (711 μC/m2) and mechanical characteristics of the composite membrane, but also the friction coefficient (COF) and thermal conductivity of the 2 wt% hBNNS/PVDF composite membrane decreased by 28.6 % and increased by 22.2 % compared to the PVDF matrix, respectively. The optimized TENG delivers a peak voltage of 434 V, a current of 53 μA, and a power of 4.84 mW. Furthermore, it exhibits exceptional ultra-robust, enabling continuous operation for 72 h at a wind speed of 17.5 m/s while maintaining performance above 90.6 %. Additionally, the TENG is capable of effectively powering a smart hygrothermograph and realizing wireless real-time monitoring, or directly lit up 102 white LEDs in a serial connection. This work addresses the challenges of low output performance and limited lifespan in TENG from a material perspective, providing a valuable reference method for the design of negative triboelectric materials with high surface charge density, good mechanical properties, low COF, and high thermal conductivity.

The Eye and Nose Identification Chip Controller-Based on Robot Vision Using Weightless Neural Network Method

Increasingly advanced image analysis in computer vision, allowing computers to interpret, identify, and analyze pictures with accuracy comparable to humans. The availability of data sources in decimal, hexadecimal, or binary forms enables researchers to take the initiative in applying their study findings. Decimal formats are typically used on traditional computers like desktops and minicomputers, whereas hexadecimal and binary formats were utilized on single-chip controllers. Weightless Neural Network is a method that can be implemented in a single chip controller. The aim of this research is to develop a facial recognition system, for eye and mouth identification, that works in a single chip controller or also called a microcontroller. The suggested method is a Weightless Neural Network with Immediate Scan approach for processing and identifying eye and nose patterns. The data will be handled in many memory locations that are specifically designed to handle massive volumes of data. The data is made up of primary face data sheets and face input data. The data sets utilized are (x,y) pixels, and frame sizes range from 90x90 pixels to 110x110 pixels. Each face shot will be processed by selecting the region of the eyes and nose and saving it as an image file. The eye and nose will identify the face frame. Next, the photos will be converted to binary format. A magazine matrix will be used to transmit binary data from a minicomputer to a microcontroller via serial connection. Based on a known pattern, the resultant similarity accuracy is 83,08% for the eye and 84,09% for the sternum. In contrast, the similarity percentage for an eye ranges from 70% to 85% for an undefined pattern.

دراسة عملية لاداء سخان ماء شمسي ذو الدوران الطبيعي المتصل على التوالي

This research paper presents an experimental study on the performance of a natural circulation solar water heater system with two typical collectors connected in series. The paper provides a comprehensive analysis of the system's thermal performance under different load conditions, including no-load, intermittent, and continuous load. Mean storage tank, solar collector means plate (the left) temperature and thermosyphon flow rate in a vertical tank were measured. Results showed that there was variation in solar water tank and collector plate temperature under load and no-load conditions. Analysis of thermal performance of the system was conducted for each condition. The highest plate temperature (100 ˚C or even more) with no circulation of both collector and load conditions, indicate the high quality of the solar collectors even during the cold season. The collector’s arrangement in series connection is of highest gain in energy and higher storage tank mean water temperature. Several characteristic equations obtained to represent the performance of the present natural circulation system under collector connection arrangement in series. In fact, when large amount of hot water was required for a certain purpose (Industrial sector for example - MSF plant or central heating), multiple collectors are to be deployed in series and in parallel to produce the required amount (quantity) and desired temperature (quality) at the same time. Key words: Thermosyphon solar water heater, storage tank profile temperature, Solar Water Heaters (SWHs), instantaneous efficiency, collector flow factor, collector efficiency factor, collector heat removal factor

Tip effect of NiCo-LDH with low crystallinity for enhanced energy storage performance of yarn-shaped supercapacitors

Layered double hydroxides (LDHs) are considered promising materials for supercapacitor applications. However, the development of yarn-shaped supercapacitors (YSCs) with high electrochemical performance utilizing LDHs remains challenging. In this study, the NiCo-LDHs with various morphologies (nano-needles, nano-sheets, needle-sheet composites, and nano-flowers) were grown on carbon nanotubes (CNTs)-functionalized cotton yarn via a co-precipitation technique for YSC applications. Among these, the yarn incorporating nano-needle NiCo-LDHs exhibited reduced crystallinity yet demonstrated a superior areal capacitance compared to other morphologies, following a diffusion-controlled process. Finite element simulations were subsequently conducted to investigate this phenomenon, revealing that the lower-crystallinity nano-needle NiCo-LDHs accumulated a greater charge at their tips, thereby enhancing redox reactions and achieving higher energy storage capacitance. Subsequently, the yarns with nano-needle NiCo-LDHs were assembled into flexible quasi-solid-state symmetric YSCs, achieving a peak areal capacitance of 124.27 mF cm−2 and an exceptionally high energy density of 39.4 μWh cm−2 at a current density of 0.2 mA cm−2. Furthermore, our YSCs can be scaled up through serial or parallel connections and integrated into fabrics, making them suitable for wearable energy storage applications. This work provides an efficient method for fabricating high-performance YSCs and demonstrates significant potential for wearable energy storage devices.

Binary Biomass-Based Electrolyte Films for High-Performance All-Solid-State Supercapacitor.

Solid-state electrolytes have received widespread attention for solving the problem of the leakage of liquid electrolytes and effectively improving the overall performance of supercapacitors. However, the electrochemical performance and environmental friendliness of solid-state electrolytes still need to be further improved. Here, a binary biomass-based solid electrolyte film (LSE) was successfully synthesized through the incorporation of lignin nanoparticles (LNPs) with sodium alginate (SA). The impact of the mass ratio of SA to LNPs on the microstructure, porosity, electrolyte absorption capacity, ionic conductivity, and electrochemical properties of the LSE was thoroughly investigated. The results indicated that as the proportion of SA increased from 5% to 15% of LNPs, the pore structure of the LSE became increasingly uniform and abundant. Consequently, enhancements were observed in porosity, liquid absorption capacity, ionic conductivity, and overall electrochemical performance. Notably, at an SA amount of 15% of LNPs, the ionic conductivity of the resultant LSE-15 was recorded at 14.10 mS cm-1, with the porosity and liquid absorption capacity reaching 58.4% and 308%, respectively. LSE-15 was employed as a solid electrolyte, while LNP-based carbon aerogel (LCA) served as the two electrodes in the construction of a symmetric all-solid-state supercapacitor (SSC). The SSC device demonstrated exceptional electrochemical storage capacity, achieving a specific capacitance of 197 F g-1 at 0.5 A g-1, along with a maximum energy and power density of 27.33 W h kg-1 and 4998 W kg-1, respectively. Furthermore, the SSC device exhibited highly stable electrochemical performance under extreme conditions, including compression, bending, and both series and parallel connections. Therefore, the development and application of binary biomass-based solid electrolyte films in supercapacitors represent a promising strategy for harnessing high-value biomass resources in the field of energy storage.

Research on Conduction Delay Time Characteristics of Double-Gap Surface Flashover Triggered Multistage Vacuum Switch

Due to the insulation saturation effect of a vacuum gap, the series connection is the main method to improve the capability of the triggered vacuum switch (STVS) to withstand voltage. In this paper, a double-gap surface flashover triggered multistage vacuum switch (DMVS) is constructed based on a removable vacuum chamber. The DMVS consists of a surface flashover triggered vacuum gap (STG) and a self-breakdown vacuum gap (SBG) in series. The trend in DMVS conduction delay time under different operating parameters and gap distances is firstly measured through experiments, and then the conduction delay time characteristics of DMVS and single-gap STVS compared. The test results show that increasing the trigger current and operating voltage and decreasing the gap distance of each vacuum gap can optimize the conduction delay time of the DMVS, but the voltage division ratio between the STG and the SBG has no obvious influence on the conduction delay time. The comparison result between the DMVS and the STVS shows that increasing the number of series gaps increases the conduction delay time but, for a certain vacuum gap distance, DMVS exhibits superior conduction delay time characteristics compared to STVS.

Investigation of the Effects Caused by Current Interruption Devices of Lithium Cells at High Overvoltages

A faulty voltage measurement can lead to the overcharging of a Li-Ion cell, resulting in gas formation and heating inside the cell, which can trigger thermal runaway. To mitigate this risk, cylindrical cells are equipped with a Current Interrupt Device (CID), which functions as a pressure relief valve, disconnecting the electrical circuit within the cell when internal pressure rises. However, this disconnection causes the cell to suddenly become highly resistant, posing a significant issue in series-connected cells. In such configurations, a portion or even the entire system voltage may drop across the disconnected cell, substantially increasing the likelihood of an electric arc. This arc could ignite any escaping flammable gases, leading to catastrophic failures. In a series of tests conducted on three different cell chemistries—NMC (Nickel Manganese Cobalt), NCA (Nickel Cobalt Aluminum), and LFP (Lithium Iron Phosphate)—it was found that the safe operation of the CID cannot be guaranteed for system voltages exceeding 120 V. Although comparative tests at double the nominal cell voltage did not exhibit the same behavior, these findings suggest that current safety standards, which recommend testing at double the nominal voltage, may not adequately address the risks involved. The tests further revealed that series connections of cells with CIDs are inherently dangerous, as, in the worst-case scenario, the entire system voltage can be concentrated across a single cell, leading to potential system failure.

Asymmetric lithium supercapacitors with solid-state hybrid electrolytes containing zeolite particle and water-soluble polymer

Here we demonstrate that high-performance solid-state hybrid electrolytes are prepared via environment-friendly water-based processes of zeolite Y (Zy) particle, branched-poly(ethylene imine) (bPEI), and lithium hydroxide (LiOH). The hybrid Zy:bPEI:LiOH electrolytes (ZyPL) were successfully applied to fabricate asymmetric-type lithium supercapacitors consisting of graphite-based active electrodes and indium-tin-oxide (ITO) counter electrodes. Results showed that the ion conductivity of electrolytes was greatly dependent on the Zy content and reached the highest value (ca. 0.28 mS/cm) at Zy = 30 wt% due to the formation of interfacial ion transport channels between Zy particles and bPEI chains. The galvanostatic charging/discharging (GCD) test revealed that the ZyPL supercapacitors could deliver the highest potential of 2.28 V at Zy = 30 wt% compared to 1.86 V at Zy = 0 wt%. In particular, the ZyPL supercapacitors, after charging at 0.1 mA/g, exhibited a long-lasting high-potential level of > 1.0 V at Zy = 30 wt% compared to 0.5 V at Zy = 0 wt%. The long-term GCD cycle test disclosed that the ZyPL supercapacitors could work stably with a capacitance retention of 91.7 % even after 3000 cycles. The series connection of six ZyPL supercapacitors delivered ca. 10.94 V with consistent charging/discharging characteristics.

Utilizing Connection of Multiple Peltier Cells to Enhance the Coefficient of Performance

Peltier cells are commonly used in low-power cooling applications, such as automotive refrigerators and electronics temperature regulation systems. These applications are typically low-energy in nature. There is currently a growing emphasis on energy conservation and waste heat utilization in the energy industry. This paper explores the possibility of improving the heating or cooling coefficient of performance (COP) of Peltier cells through intelligent serial and parallel connections. The purpose of this work is to raise the question of whether it would be possible to reconsider the concept of harnessing the “energy” potential of Peltier cells. The utilized model is in line with the current state of the art, and the case study is based on parameters measured on a commercially available Peltier cell. The resulting COP, when considering current materials, remains inferior to the COP of compressor-based heat pumps. For low-power devices, it can represent a technically and economically comparable solution.

Submersible solar powered pump system design for sustainable agriculture using

Current climate change has many implications for people's livelihoods, one of which is the lack of seasonal rainfall, leading to drought, which in turn reduces agricultural yields. Therefore, people have to plant dry season crops, and in the dry season, crops have to rely on water from rivers and streams. But some areas where there is no stagnant water or stagnant water are very dry. So, our team did experimental research and studied the feasibility of using solar groundwater pumping systems in agriculture. It will cover the design, control, and know the strengths and weaknesses of the system, and its suitability to be used in our country, especially in the eight Northern provinces. In this research, we designed and used a Submersible solar-powered pump system, after installation, the system will work automatically without the need to turn it on and off. The panel size used is 330 watts, two panels serial connection for a total of 660 watts; the Submersible solar-powered pump is 400 watts, 48 voltages, Automatic control system, Groundwater depth 68 meters, the diameter of the surface pipe 0.1 meters, The diameter of the suction pipe has a cross-sectional area of 0.025 meters. Experimentation shows the water pump deep at 30 m can absorb more water than 25 m deep. The capacity of the system to be used for agriculture in one day can use 6.13 m3 of water, which is enough for cultivation in an area of 8,000 m2 or more, depending on the type of crop grown. The power generated per day is 3,142 W and is used at 3.14 kWh per day as well or 94.24kWh per month which is sufficient for the use of the system. In cash compared to the electricity consumption from the Electricity du Laos is 39,000 LAK per month. The maximum amount of water collected is 6.13 m3 per day or 184 m3 per month, which is 646,644 LAK per month compared to the water supply system, in the analysis of the cost of installation is 31 months or 2 years and 7 months.

Bipolar Textile Composite Electrodes Enabling Flexible Tandem Solid-State Lithium Metal Batteries.

A majority of flexible and wearable electronics require high operational voltage that is conventionally achieved by serial connection of battery unit cells using external wires. However, this inevitably decreases the energy density of the battery module and may cause additional safety hazards. Herein, a bipolar textile composite electrode (BTCE) that enables internal tandem-stacking configuration to yield high-voltage (6 to 12V class) solid-state lithium metal batteries (SSLMBs) is reported. BTCE is comprised of a nickel-coated poly(ethylene terephthalate) fabric (NiPET) core layer, a cathode coated on one side of the NiPET, and a Li metal anode coated on the other side of the NiPET. Stacking BTCEs with solid-state electrolytes alternatively leads to the extension of output voltage and decreased usage of inert package materials, which in turn significantly boosts the energy density of the battery. More importantly, the BTCE-based SSLMB possesses remarkable capacity retention per cycle of over 99.98% over cycling. The composite structure of BTCE also enables outstanding flexibility; the battery keeps stable charge/discharge characteristics over thousands of bending and folding. BTCE shows great promise for future safe, high-energy-density, and flexible SSLMBs for a wide range of flexible and wearable electronics.

Research on a New Inverter Control Strategy of Induction Heating Power Supply

To achieve “high voltage, low current” in the induction heating power circuit, enhance the flexibility of component selection in the circuit, and improve the quality of the inverter’s output waveform, a new control strategy of a single-phase NPC three-level inverter with unipolar frequency-doubling SPWM method is proposed. With the series connection of IGBTs in a single-phase NPC three-level inverter, the voltage withstand requirement of IGBT is reduced by half. The middle four IGBTs are controlled using unipolar frequency-doubling SPWM, while the outer four IGBTs are turned on later and turned off earlier to address the neutral point voltage imbalance issue in the inverter. Simulation results show that, compared with the traditional bipolar SPWM-controlled single-phase full-bridge inverter, the DC-side input voltage of the inverter can be double, and the current flowing through the entire circuit can be halved under the same output power using the proposed method.

Harvesting Energy from Rainfall: Initial Study by Exploring Diverse Piezoelectric Array Configurations for Enhanced Electricity Generation in Proteus Software

This paper presents an innovative approach to designing and analyzing a simulated piezoelectric energy harvesting system for electricity generation, employing various array connections using Proteus software. The ingenious concept of harnessing energy from rainfall through piezoelectric technology has become an exciting way to turn a common natural occurrence into a possible power source. The rainfall energy harvesting introduces a novel approach that capitalizes on the mechanical energy imparted by raindrops as they strike surfaces, such as rooftops, pavements, or specially designed structures. This study explores distinct piezoelectric connection types to determine their impact on output voltage, focusing on applications such as rechargeable battery and LEDs. The system begins by harvesting vibration and applying it to the piezoelectric disc. The investigation prioritizes identifying the optimal array connection design. Array configurations of series (S), parallel (P), and combination of series-parallel (SP) are assessed in the simulation. Notably, the series connection of 10 units of piezoelectric elements yielded the highest output voltage at 8.5V. The findings provide valuable insights into finding the optimal array connections in enhancing piezoelectric electricity generation. This research contributes to the leading of potential applications of piezoelectric energy harvesting from rainfall, offering insights into a greener and more self-sufficient energy future.

A compact motorized end-effector for ankle rehabilitation training.

This paper introduces a compact end-effector ankle rehabilitation robot (CEARR) system for addressing ankle range of motion (ROM) rehabilitation. The CEARR features a bilaterally symmetrical rehabilitation structure, with each side possessing three degrees of freedom (DOF) driven by three independently designed actuators. The working intervals of each actuator are separated by a series connection, ensuring they operate without interference to accommodate the dorsiflexion/plantarflexion (DO/PL), inversion/eversion (IN/EV), and adduction/abduction (AD/AB) DOF requirements for comprehensive ankle rehabilitation. In addition, we integrated an actuator and foldable brackets to accommodate patients in varied postures. We decoded the motor intention based on the surface electromyography (sEMG) and torque signals generated by the subjects' ankle joints in voluntary rehabilitation. Besides, we designed a real-time voluntary-triggered control (VTC) strategy to enhance the rehabilitation effect, in which the root mean square (RMS) of sEMG was utilized to trigger and adjust the CEARR rehabilitation velocity support. We verified the consistency of voluntary movement with CEARR rehabilitation support output for four healthy subjects on a nonlinear sEMG signal with an metric of approximately 0.67. We tested the consistency of triggering velocity trends with a linear torque signal for one healthy individual with an metric of approximately 0.99.

Two Birds with One Stone: Impedance-Voltage Dual-Mode Low Humidity Sensor Based on LiBr-MOF-801 with High Response.

Dual-mode humidity sensors have received wide attention in recent years due to their great potential in multifunction applications. Herein, following a "two birds with one stone" strategy, a dual-mode and self-powered low humidity sensor based on LiBr-MOF-801 with high response and power generation is proposed. The optimized LiBr-MOF-801-based sensor exhibits impedance-voltage dual-mode sensitivity in the low humidity range of 0-23% relative humidity (RH) with high response (57.1 and 0.61V), small hysteresis (0.3% RH) and good long-term stability at room temperature (20°C). Moreover, an integrated humidity power generator is obtained by series connection of the self-powered humidity sensor within 15cm2, and the output voltage reaches 2.6V with an output power density of 110 nW cm-2, and can be used as energy, supplying power to commercial electronic equipment even in low humidity. This work provides a new sight for fabricating high-performance, dual-mode, and self-powered low-humidity sensors.

Fabrication of high performance BaSnO3/PVDF piezoelectric nanogenerator through high surface area BaSnO3 nanoparticle assisted β-phase stabilization of PVDF

Piezoelectric nanogenerators (PENGs) are becoming increasingly popular for energy generation and their use in smart electronics. In this study, a barium stannate (BaSnO3)-doped polyvinylidene fluoride (PVDF)-based PENG has been fabricated for the first time. The β-phase of PVDF was stabilized by optimizing the doping of BaSnO3 nanoparticles without the need for external electrical poling. The high surface area of the BaSnO3 nanoparticles promotes the nucleation of the polar β-phase in PVDF through electrostatic interaction. A low-cost solution casting method was used to prepare flexible BaSnO3/PVDF nanocomposite containing 5 wt% BaSnO3, which was then shaped and sandwiched between copper electrodes and protected with a thin PDMS layer to create the final PENG. The fabricated PENG can generate up to ∼41 V of voltage, ∼1.51 µA of current and ∼18.1 µW/cm2 of power density when ∼15.7 kPa pressure is applied by a human finger. The PENG can also charge capacitors, power up 16 LEDs in a series connection, and power other small electronics such as wristwatches, speakers, and calculators. Additionally, the PENG can activate the electrochromic material methyl viologen, which is commonly used in smart window applications.