Scratch Behavior Research Articles

Scratch load and indenter type dependent scratch evaluation of milled carbon fiber filled basalt fiber/epoxy composites with factorial design

AbstractThis work investigates the addition of milled carbon fiber reinforcement and its effect on scratch resistance and mechanical durability for basalt fiber/epoxy composites, assessed under varied loading conditions with the aid of different indenter types according to a factorial design. Composites with MCF content from 0 to 10 wt% were prepared. Scratch behaviors under Vickers and Rockwell indenters were studied for loads of 5, 10, and 15 N. The addition of 10 wt% MCF has resulted in scratch hardness increase from 13.255 N/mm2 up to 47.952 N/mm2, depending on the type of indenter used. Precisely, in conditions of a 5 N load and when a Rockwell‐type indenter was used, a scratch hardness maximum of 47.952 N/mm2 was achieved, while for a Vickers‐type indenter under the same conditions, the maximum value of its equivalent was 23.327 N/mm2. Profilometric and SEM analyses evidence that matrix cracks and surface deformation have been reduced with higher MCF content, at least for the application of lower scratch test loads. The mechanical and surface performances of the basalt fiber composites were found to be considerably improved by the reinforcement with MCF.Highlights Scratch resistance for milled carbon fibers increases and peaks at 10 wt% reinforcement. The Rockwell indenter indicates a steady increase in hardness up to 47,952 N/mm2. Peak hardness of 10 wt% is observed under the Vickers indenter for the 5 N load. Higher milled carbon fiber content reduces matrix cracking and surface deformation. There is a clear correlation between scratch performance, milled carbon fiber content, and indenter type.

Simultaneous effect of microwave sintering and TiO2 addition on sinterability, mechanical properties, and scratch resistance of zirconia toughened alumina ceramics

This paper delves into the transformative impact of varying titanium dioxide (TiO2) content on the sinterability, physical, and mechanical properties, as well as scratch behavior, of zirconia-toughened alumina (ZTA) ceramic composites. By adjusting TiO2 content from 0 wt% to 5 wt% and employing advanced microwave sintering at 1150 °C, the study aims to lower the sintering temperature of ZTA. Microwave sintering, known for its efficiency and rapid processing, enables significant enhancements in material properties at reduced temperatures. Notably, incorporating TiO2 into ZTA yields remarkable improvements in physical and mechanical attributes, with the optimal TiO2 content determined to be 3 wt%. At this concentration, the composite achieves exceptional properties: a relative density of ∼99 %, microhardness of ∼2002 HV, and an indentation fracture toughness of ∼6.13 MPa m0.5. These enhancements represent increases of over 120 % in hardness and 61 % in toughness compared to TiO2-free ZTA. Additionally, the highest scratch resistance is observed at 3 wt% TiO2, evidenced by a minimal scratch depth of ∼7.53 μm. However, exceeding the 3 wt% solubility limit results in the formation of secondary phases, such as tialite (Al2TiO5) and zirconium titanate (ZrTiO4), which degrade the composite's properties. This research underscores the potential of TiO2 doping and microwave sintering to elevate the performance of ZTA ceramics, offering a pathway to superior materials for advanced applications.

Resolving high-strain-rate scratch behavior of Ti6Al4V in experiment and meshless simulation

The outstanding strength-to-weight ratio and corrosion resistance of titanium have made it the material of choice in the aerospace industry and medicine. The alpha–beta alloy Ti6Al4V is particularly preferred for its excellent mechanical and bio-compatible properties. Despite its advantages, the low thermal conductivity and poor tribological performance of titanium pose significant challenges during manufacturing and in operation. This research offers deep insights into the high strain rate behavior of Ti6Al4V under abrasive load, such as e.g. experienced in machining, by modifying the standard scratch test setup and using optimized Johnson–Cook material parameters to perform Material Point Method (MPM) simulations. The MPM simulations provide accurate predictions of the data gathered through high strain rate scratch experiments. We found an increase in the von Mises stress distribution as well as the normal and tangential forces required to perform a scratch of the same depth as the strain rate increases. The morphology of the scratch profiles also showed an increase in the height of the ridges that form as the scratching speed increases. These findings are in line with the increase in yield strength and work hardening with growing strain rate. This study bridges the gap between simulation models and experimental observations by providing insights for improved machining strategies and surface treatments that can enhance the performance of Ti6Al4V in demanding applications.

Structural, mechanical, corrosion, and early biological assessment of tantalum nitride coatings deposited by reactive HiTUS

This study examined microstructure, mechanical, corrosion properties and initial biological evaluation of the tantalum nitride (Ta-xN, where x – nitrogen flow rate during deposition) coatings prepared by reactive High Utilization Sputtering (HiTUS) at various nitrogen flow rates (x = 0, 2, 4, 6, and 8 sccm). Coatings were deposited on a novel Mg alloy (Mgbal.-Zn0.9-Y2.05-Al0.25 at. %) containing long-period stacking ordered (LPSO) phases. The coatings' structure was analyzed using a combination of SEM/FIB/TEM techniques, while XRD determined the phase composition. The mechanical parameters investigated included hardness, indentation modulus, and scratch behavior. The corrosion resistance of the coatings with respect to the bare substrate was evaluated in chloride-containing solutions. The wettability and early biological assessment of the coatings were also examined. The phase evolution strongly influenced the hardness and indentation modulus. The Ta-xN coatings made at x = 2 sccm nitrogen corresponding to HCP-Ta2N exhibited the highest hardness and indentation modulus. An increase in nitrogen flow rates resulted in the formation of FCC structure with slightly reduced hardness and indentation modulus. In addition, Ta-xN coatings (x ≥ 4sccm) showed superior corrosion resistance compared to BCC structured α-Ta, enhancing the corrosion performance of the Mg-LPSO bulk substrate. Finally, at the early incubation stage (24 h), L929 fibroblasts exhibited better cell attachment to the Ta-6N coating than to the bare Mg-LPSO substrate.

Effect of physical aging on scratch behavior of polycarbonate

AbstractPhysical aging refers to relaxation of the polymer glassy state toward the amorphous state and this phenomenon affects their physical‐mechanical properties. This work investigates the effect of physical aging on polymer scratch behavior and visibility. It was shown that mechanical properties were significantly modified over the aging time, especially the yield stress, in turn affecting polymer scratch behavior. As a matter of fact, the critical load for the onset of scratch visibility was shown to increase with the aging, thus improving sensitivity of polymer to scratches. Such behavior was strictly related to the yield stress increase with the aging time. The usefulness of the present work is highlighted, and some future perspectives are discussed.

The effects of the angle between the indenter edge and the scratch direction on the scratch characteristics of Ti–6Al–4V alloy

Ti–6Al–4V alloy has become a crucial raw material in aerospace and other industries owing to its exceptional mechanical properties. However, it is also a typical difficult-to-machine material, and its removal process and mechanism have been widely investigated by scratch testing. Nevertheless, the inherent non-rotational symmetry of the Vickers indenter introduces a crucial parameter, i.e., the angle λ between the indenter edge and the scratch direction, which affects not only the mechanical response of materials but also its surface formation mechanism during scratch. This study systematically characterized the micro/nano scratch characteristics of Ti–6Al–4V alloy under three typical angles λ (0°, 22.5°, 45°) as well as various normal forces and scratch speeds. The coefficient of friction (COF), scratch depth, scratch width, residual scratch morphology, and specific scratch energy were comparatively analyzed. Finite element simulations confirmed that the direction of material flow changed with the change in angle λ. The corresponding deformation mechanisms during scratch were discussed accordingly. The results revealed a significant influence of the angle λ on the scratch behaviors and surface quality of Ti–6Al–4V alloy.

High-temperature hardness and scratch behaviour of differently strengthened iron aluminide laser claddings

Fe3Al-based iron aluminides provide notable high-temperature properties at a comparatively low overall ecological impact. To improve their wear resistance, different strengthening strategies are studied for which Fe3Al-based laser claddings (30 at.% Al) are alloyed either with Si, C, or Ti and B. Detailed microstructural investigations after laser metal deposition (LMD) including X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD) were performed. Results show that Si-alloyed claddings are single-phase with equiaxed grains of average sizes from ∼350 μm (1 at.% Si) decreasing with increasing Si content to ∼50 μm at 3 and 5 at.% Si. Contrary, the C-alloyed claddings microstructures are dendritic and ledeburite-like with perovskite-type carbides Fe3AlC0.6. The Ti- and B-alloyed cladding exhibits finely dispersed TiB2-type precipitations; at low contents in the sub-micron range and mainly present at the grain boundaries, at higher additions are quite large (3–5 μm) and present within individual grains. The individual hardphases, as quantified via nanoindentation, of Fe3AlC0.6-type carbides or TiB2-type borides exhibit average hardness values of ∼7.5 GPa and ∼ 45.5 GPa, respectively. Therefore, the hardness of C- and Ti & B-alloyed claddings increases from ∼260 HV10 (Fe3Al) to 405 HV10 (Fe3Al plus 5 at.% C) and to 340 HV10 (Fe3Al plus 3 at.% and 6 at.% B). The higher hardness of the C-alloyed cladding stems from the s higher hardphase content; the matrix hardness ranges between 4 and 5 GPa for all precipitation-strengthened claddings. Contrary, the Si-alloyed cladding exhibits a pronounced increase to 5.7 ± 0.8 GPa upon adding up to 5 at.% Si. Thus, an overall hardness of ∼350 HV10 is quantified on the expense of ductility (relaxation cracking after LMD). High-temperature hardness and scratch tests as well as wear investigations prove that the C- as well as Ti and B-alloyed claddings are superior to the plain Fe3Al and Si-alloyed ones, making them promising alternatives to other wear protection materials based on Co, Ni or Cr.

Low cycle fatigue of doped tetrahedral amorphous carbon coatings by repetitive micro scratch tests

In contrast to the conventional progressive scratch testing where load is increased up to a critical damage level, the repetitive scratch testing is an assessment of coating behavior under repeatedly applied subcritical load. It often represents a better approximation to actual application conditions of well-designed coating systems where overcritical conditions typically do not occur. In this work, the cyclic micro scratch behavior of differently doped amorphous carbon coatings with similar coating thicknesses were studied using repetitive scratch tests at loads that correspond to 40 %, 60 % and 80 % of the critical loads from progressive scratch testing. Depending on the doping element, the structural and mechanical properties changed, in some cases considerably, which also had a clear effect on the test results. The damage progression was examined using optical microscopy, friction coefficient, and residual depth measurements. The progression of failure phenomena was categorized into different stages. Furthermore, the critical number of cycles for coating failure was recorded at the various load levels. For the identification of the critical cycles, the use of the deviation of the friction coefficient from its mean value has proven to be a valuable parameter. The approach of testing at different load levels allows the creation of low cycle fatigue curves to evaluate the coating behavior. It was found that the hardness and residual stresses of the coatings had different effects on the lifetime of the coatings at the various load levels, i.e. higher hardness and residual compressive stresses were only beneficial for moderate stress levels with low plastic substrate deformation. The results demonstrate that the cyclic scratch test is a powerful tool for comparative damage assessment at different load scenarios.

Effect of grain boundary on scratch behavior of polycrystalline copper

The anisotropy in the elastoplastic response of crystalline solids influences substantially their scratch resistance at the microscale. While grain boundaries typically act as obstacles to the motion of dislocations at the grain level, the scratch behavior in the vicinity of the grain boundary is influenced by other factors such as crystallographic orientation and pile-up topography. We performed a systematic set of nano-scratch simulations using the mechanism-based strain gradient crystal plasticity to study the evolution of scratch force and depth near grain boundaries. To validate our model, we conducted a nano-scratch test on a polycrystalline copper sample and compared the scratch depth profile for a specific grain boundary with the simulated result, where a good qualitative agreement was achieved. Our simulations showed that the scratch depth, force, and hardness vary between the corresponding values for the individual constitutive grains, and the variation decreases by reducing the grain size. Additionally, we analyzed the scratch response in terms of the pile-up topography and subsurface stresses and distinguished different regimes when the indenter approaches and scratches across the boundary. Our findings offer a new direction to optimize the scratch resistance of polycrystalline metals by tailoring the size and orientation of grains near the surface. Additionally, it introduces scratching as a robust material characterization method.

Understanding the effect of solid lubricants on scratch behavior in epoxy resins: An experimental and statistical approach

AbstractEpoxy resins inherently have low resistance to scratching. To increase the scratch resistance of epoxy resins, reinforcing solid lubricants into the resin is an option. For this purpose, in this study, polytetrafluoroethylene (PTFE) and graphite were reinforced in two different epoxy resins (rigid and toughened) at different reinforcement ratios (5, 10, and 15 wt%). The effects of solid lubricant reinforcement on the scratch behavior of rigid and toughened epoxy resins were examined both experimentally and statistically. Scratch tests were performed throughout a distance of 10 mm using a test apparatus under a load of 15 N and a scratch speed of 30 mm/min. Following the scratch tests, the COF (Coefficient of Friction) values, scratch hardness, scratch width, and depth of all samples were determined and compared to neat epoxy for each resin. In general, it has been determined that solid lubricant reinforcement at higher reinforcement ratios has a positive effect on the COF value (15 wt%). In the case of 15 wt% graphite reinforced rigid and toughened epoxy, a decrease of 15.90% and 17.77%, respectively, was obtained in the COF value compared to the neat epoxy. After the scratch tests, statistical analysis was performed according to RSM to support the experimental results, and ANOVA tables were obtained.Highlights Epoxy adhesives exhibit low scratch resistance. Examining the impact of PTFE and graphite reinforcement on scratch behavior. Two types of epoxy and varied reinforcement ratios (5, 10, and 15 wt%) were studied. Solid lubricant reinforcement to epoxy positively affected scratch behavior.

Cracking behavior during scratching brittle materials with different-shaped indenters

The cracking behavior greatly influences the material removal and surface integrity during the abrasive machining of brittle materials. The abrasive machining can be simplified as a series of scratching by different-shaped indenters. In this paper, a scratch-induced stress field model is built to analyze the cracking behavior during scratching brittle materials. The model considers conical, pyramidal, and spherical (CPS) indenters and correlates the scratch-induced principal stress with workpiece material properties, indenter geometries, and scratch behavior parameters (e.g., scratch normal load, tangential load, friction coefficient, scratch depth). With the model, the effects of scratch depth and indenter geometries on the scratch behavior and cracking behavior are investigated. The results show that the scratch load decreases when a sharper indenter or a spherical indenter with a smaller radius is used. The larger the scratch depth, the easier it is for radial, median, and lateral (RML) cracks to initiate. There is an optimal indenter half-apex angle at which it is most difficult to initiate radial and median cracks. The lateral crack easily initiates when the indenter becomes sharp. The initiation position of radial crack changes from being in front of the indenter to being behind it as the scratch depth increases or the half-apex angle decreases. The propagation angle of radial crack decreases, while that of median crack increases with an increase in scratch depth. The sizes of RML cracks increase with an increasing scratch depth or half-apex angle. Finally, the model is validated through scratching experiments on fused silica using CPS indenters and by referencing previous research. It demonstrates that the model can accurately determine the sizes of RML cracks, with an average relative error of less than 11%. This research provides guidance on selecting suitable process parameters or indenter geometries to increase the material removal rate and mitigate the crack damage during the abrasive machining of brittle materials.

Scratch and wear resistance of interstitial-free steel subjected to severe shot peening

Surface integrity in terms of scratch and wear resistance is the major concern of any engineering component, which is attributed to most of the surface damages. A popular way of improving such behaviours is the mechanical treatment of the surface. The current investigation studied the improvement of scratch and wear properties by performing shot peening on the Ti–Nb stabilised interstitial free steel, a popular choice in automotive industries. The samples were shot-peened at different coverages. It was found that the shot-peened samples showed a superior scratch and wear behaviour as compared to as-received samples. The scratch hardness was improved by 2.4 times, the wear volume was decreased by 59.6%, and the wear rate was minimal for the 2000% peened sample.

Effect of substituting Na2O with B2O3 on the crystallization and properties of MgO–Al2O3–SiO2 transparent glass-ceramics

MgO–Al2O3–SiO2 (MAS) transparent glass-ceramics were prepared with ZrO2 as a nucleating agent, and the substitution of B2O3 for Na2O on the properties of the MAS glass-ceramics was investigated systematically. The results show that the substitution of B2O3 increased the glass transition temperature, crystallization temperature, and crystallization activation energy. Additionally, there was no change in the main crystal phase of the glass-ceramics, which were ZrO2 (JCPDS PDF#.50-1089) and Al0.52Zr0.48O1.74 (JCPDS PDF#.53-0294). The crystal growth mode shifted from three-dimensional growth to two-dimensional growth, and the crystal morphology transformed from a spherical appearance to a star-shaped appearance. Moreover, the mechanisms of the property changes induced by B2O3 substitution are revealed and discussed. The transmittance of MAS glass-ceramics without B2O3 decreased from 88 % to 32 % as the crystallization temperature increased from 800 °C to 920 °C, and decreased from 90 % to 8 % when B2O3 was added. Additionally, the Vickers hardness of MAS glass-ceramics decreased from 6.37 GPa to 6.13 GPa, after the introduction of B2O3, while, the fracture toughness increased from 1.48 MPa m1/2 to 1.55 MPa m1/2. The scratch behaviour of glass-ceramics exhibits a negative correlation with the applied load, but a positive correlation with the crystallization temperature. In particular, the incorporation of B2O3 substantially enhances the scratch resistance of glass-ceramics. The conclusions provide researchers with the roles of B2O3 in crystallization kinetics, microstructure, transmittance, and mechanical properties of MAS transparent glass-ceramics for various applications such as covers.

Chemokine receptor CXCR2 in primary sensory neurons of trigeminal ganglion mediates orofacial itch.

The CXCR2 chemokine receptor is known to have a significant impact on the initiation and control of inflammatory processes. However, its specific involvement in the sensation of itch is not yet fully understood. In this study, we aimed to elucidate the function of CXCR2 in the trigeminal ganglion (TG) by utilizing orofacial itch models induced by incision, chloroquine (CQ), and histamine. Our results revealed a significant up-regulation of CXCR2 mRNA and protein expressions in the primary sensory neurons of TG in response to itch stimuli. The CXCR2 inhibitor SB225002 resulted in notable decrease in CXCR2 protein expression and reduction in scratch behaviors. Distal infraorbital nerve (DION) microinjection of a specific shRNA virus inhibited CXCR2 expression in TG neurons and reversed itch behaviors. Additionally, the administration of the PI3K inhibitor LY294002 resulted in a decrease in the expressions of p-Akt, Akt, and CXCR2 in TG neurons, thereby mitigating pruritic behaviors. Collectively, we report that CXCR2 in the primary sensory neurons of trigeminal ganglion contributes to orofacial itch through the PI3K/Akt signaling pathway. These observations highlight the potential of molecules involved in the regulation of CXCR2 as viable therapeutic targets for the treatment of itch.

Study of Heat Input Effects on the Microstructure of Lean Duplex 2101 Shielded Metal Arc Weld and Its Effect on Mechanical Properties, Corrosion, and Scratch Behavior

Study of Heat Input Effects on the Microstructure of Lean Duplex 2101 Shielded Metal Arc Weld and Its Effect on Mechanical Properties, Corrosion, and Scratch Behavior

An atopic dermatitis-like murine model by skin-brushed cockroach Per a 2 and oral tolerance induction by Lactococcus lactis-derived Per a 2.

Atopic dermatitis (AD) is a complex, chronic inflammatory skin disease. An estimated 57.5% of asthmatic patients and 50.7% of rhinitis patients are allergic to cockroaches in Taiwan. However, the role of cockroaches in the pathogenesis of AD is undetermined. Oral tolerance might be another strategy for protecting against AD and allergic inflammation by regulating T helper 2 (Th2) immune responses. Aim to examine the underlying immunologic mechanism, we developed an AD-like murine model by skin-brushing with cockroach Per a 2. We also investigated whether the systemic inflammation of AD in this murine model could be improved by specific tolerance to Lactococcus lactis-expressing Per a 2, which was administered orally. Repeated painting of Per a 2 without adjuvant to the skin of mice resulted in increased total IgE, Per a 2-specific IgE, and IgG1, but not IgG2a. In addition, epidermal thickening was significantly increased, there were more scratch episodes, and there were increases in total white blood cells (eosinophil, neutrophil, and lymphocyte) and Th2 cytokines (Interleukin (IL)-4, IL-5, IL-9, and IL-13) in a dose-dependent manner. The results revealed that oral administration of L. lactis-Per a 2 ameliorated Per a 2-induced scratch behavior and decreased the production of total IgE, Per a 2-specific IgE, and IgG1. Furthermore, L. lactis-Per a 2 treatment also suppressed inflammatory infiltration, expressions of thymic stromal lymphopoietin (TSLP) and IL-31 in skin lesions, and downregulated splenic IL-4 and IL-13 in Per a 2-induced AD mice. This study provides evidence supporting that repeated brushing of aeroallergens to the skin leads to atopic dermatitis phenotypes and oral allergen-specific immune tolerance can ameliorate AD-like symptoms and systemic inflammation and prevent progression of atopic march.

Quantification of observable behaviors following oral administration of oxycodone and nalfurafine in male rhesus monkeys

BackgroundRecent preclinical studies have investigated the atypical kappa-opioid receptor (KOR) agonist, nalfurafine, as a co-formulary with mu-opioid receptor (MOR) agonists as a potential deterrent for misuse. However, no study has investigated effects of nalfurafine combined with a MOR agonist using an oral route of administration. The objective of the current study was to measure behavioral effects of orally administered oxycodone and nalfurafine, alone and combined, in rhesus monkeys using a quantitative behavioral observation procedure. MethodsAdult male rhesus monkeys (N=5) were orally administered vehicle, oxycodone (0.56-1.8mg/kg), nalfurafine (0.001-0.0056mg/kg), or mixtures (1.0mg/kg oxycodone/0.001-0.0056mg/kg nalfurafine) in a Jell-O vehicle at multiple timepoints (10-320min). Species-typical and drug-induced behaviors were recorded by observers blinded to conditions. ResultsOxycodone alone significantly increased scratch and face-rub behaviors without affecting other behaviors. Nalfurafine decreased baseline levels of scratch without affecting other behaviors, and oxycodone-nalfurafine combinations resulted in reduced oxycodone-induced scratching at a dose (0.001mg/kg) that did not produce sedation-like effects. Oxycodone combined with larger nalfurafine doses (0.0032-0.0056mg/kg) also reduced oxycodone induced scratch that were accompanied with sedation-like effects (i.e., increased lip droop). ConclusionsNalfurafine was orally active in rhesus monkeys, and it reduced oxycodone-induced pruritus at a dose that did not produce sedation-like effects that are commonly observed with prototypical KOR agonists. Combinations of low doses of nalfurafine with MOR agonists such as oxycodone may be well-tolerated by humans who are prescribed MOR agonists for the treatment of pain.

Improving cold sprayed Ti-6Al-4V coatings controlling processing parameters: Effect on microstructure and scratch behaviour

In this work, the local wear properties of cold-sprayed (CS) Ti-6Al-4V coatings were studied to evaluate their application for aeronautical components repair. Two different CS conditions were used, and one condition was also heat-treated. A thorough microstructural study was first done to correlate the microstructure with the wear properties. Then, microscratch tests were performed. The wear rates were calculated analytically, and this method was validated with confocal microscopy. Similar wear rates to that of the material to be repaired (substrate) were obtained for the CS coating sprayed at higher temperatures and for the heat-treated one. The wear resistance was related to the ability of the coating to plastically deform and thus, with the arrangements of different dislocations observed in the coatings.

Solid particle erosion and scratch behavior of novel scrap carbon fiber/glass fabric/polyamide 6.6 hybrid composites

AbstractThis study investigated the tribological performance of hybrid composites composed of scrap carbon fiber (CF), glass fabric (GF), and polyamide 6.6 (PA6.6) through an innovative approach for reusing scrap CFs in high‐value composite structures. The experimental setup included CF/GF/PA6.6 hybrid composite laminates with varying CF contents and surface‐modified GFs, as well as PA6.6 sheets and GF/PA6.6 composite laminates. Solid particle erosion and scratch tests were conducted to assess the influence of scrap CF hybridization and GF surface modification on the tribological properties of the composites. The results demonstrated that neat PA6.6 sheets exhibited the lowest erosion rate, while the incorporation of CF and GF reinforcements had a detrimental effect on erosion resistance. The highest erosion rate was observed within the impact angle range of 15°–30° for pure PA6.6 sheets, whereas for composite laminates, it occurred within the range of 30°–45°. In contrast, CFs positively affected scratch hardness despite their negative impact on erosion resistance. Additionally, the silane treatment of GFs, which enhanced interfacial strength, improved the erosion resistance and scratch hardness of GF/PA6.6 composite laminates without CF. Profilometer‐based topographic analysis revealed a correlation between the average surface roughness of the eroded surfaces and the weight loss resulting from solid particle erosion.

Exploring the effects of thermal aging on scratch resistance of carbon fiber reinforced composite materials: A comprehensive study

AbstractThis paper investigates the scratch behavior of carbon fiber reinforced composites (CFRCs) under thermal aging conditions. Scratch depth was analyzed with respect to three parameters: velocity, thermal cycle, and direction of the scratch. The results showed that thermal aging has a significant effect on the scratch behavior of CFRCs, with an increase in thermal cycle leading to an increase in scratch depth. The scratch depth was also found to be greater in the weft direction compared to the warp direction, which can be attributed to the difference in fiber arrangement and orientation in the CFRC material. The analysis of variance (ANOVA) was performed to investigate the effect of thermal aging on the scratch behavior of CFRCs. The ANOVA results revealed that the direction of the scratch has a significant effect on scratch depth, with the weft direction showing greater scratch depth compared to the warp direction. The surface roughness of CFRCs was analyzed under thermal aging conditions and with an increase in thermal cycle leading to an increase in surface roughness. The roughness values were found to be higher in the weft direction compared to the warp direction, which can be attributed to the difference in fiber arrangement and orientation in the CFRC material.