Spectrum Scanning Research Articles

Dynamic distributed Brillouin sensing based on pump frequency-agile quadrupling modulation

We propose a dynamic distributed Brillouin sensing based on a frequency-agile quadrupling method. A common low-bandwidth direct digital frequency synthesizer (DDS) is employed to generate a few hundred MHz of frequency-agile pump pulses for Brillouin gain spectrum (BGS) scanning, and polarization multiplexing technology is utilized to further decrease the bandwidth requirement for the frequency-agile microwave signal to one-quarter. This method has low requirements for electronic devices and significantly reduces costs in systems. Static and dynamic measurement capabilities of 2 km fiber were demonstrated experimentally, the vibration frequencies of 183 Hz were measured with a sampling rate of 400 Sa/s.

A Chirped Characteristic-Tunable Terahertz Source for Terahertz Sensing.

In broadband terahertz waves generated by femtosecond lasers, spatial chirp will be simultaneously produced with the introduction of angular dispersion. The chirp characteristics of the terahertz wave will directly affect the frequency response, bandwidth response, and intensity response of the terahertz sensor. To enhance the capability of terahertz sensors, it is necessary to control and improve the chirped characteristics of broadband terahertz sources. We generate a chirped terahertz wave via optical rectification in a LiNbO3 prism using the technique of pulse front tilt. The effect of the pump-beam spot size on THz generation is systematically studied. The pump's spot size is manipulated using a telescope system. With a pump spot diameter of 1.8 mm, the scanning spectrum of the THz pulse is narrower and is divided into multiple distinct peaks. In contrast, using a pump spot diameter of 3.7 mm leads to increased efficiency in the generation of THz pulses. Also, we investigate the underlying properties governing the generation of chirped terahertz pulses using varying pump pulse spot diameters.

LSPR-susceptible metasurface platform for spectrometer-less and AI-empowered diagnostic biomolecule detection

In response to the growing demand for biomolecular diagnostics, metasurface (MS) platforms based on high-Q resonators have demonstrated their capability to detect analytes with smart data processing and image analysis technologies. However, high-Q resonator meta-atom arrays are highly sensitive to the fabrication process and chemical surface functionalization. Thus, spectrum scanning systems are required to monitor the resonant wavelength changes at every step, from fabrication to practical sensing. In this study, we propose an innovative dielectric resonator-independent MS platform that enables spectrometer-less biomolecule detection using artificial intelligence (AI) at a visible wavelength. Functionalizing the focused vortex MS to capture gold nanoparticle (AuNP)-based sandwich immunoassays causes the resulting vortex beam profiles to be significantly affected by the localized surface plasmon resonance (LSPR) occurring between AuNPs and meta-atoms. The convolutional neural network algorithm was carefully trained to accurately classify the AuNP concentration-dependent focused vortex beam, facilitating the determination of the concentration of the targeted diagnostic biomolecule. Successful in situ identification of various biomolecule concentrations was achieved with over 99 % accuracy, indicating the potential of combining an LSPR-susceptible MS platform and AI for continuously tracking various chemical and biological compounds.

Antivenom potential of the latex of Jatropha mutabilis baill. (Euphorbiaceae) against Tityus stigmurus venom: Evaluating its ability to neutralize toxins and local effects in mice

Ethnopharmacological relevanceSpecies of the Jatropha genus (Euphorbiaceae) are used indiscriminately in traditional medicine to treat accidents involving venomous animals. Jatropha mutabilis Baill., popularly known as “pinhão-de-seda,” is found in the semi-arid region of Northeastern Brazil. It is widely used as a vermifuge, depurative, laxative, and antivenom. Aim of the studyObtaining the phytochemical profile of the latex of Jatropha mutabilis (JmLa) and evaluate its acute oral toxicity and inhibitory effects against the venom of the scorpion Tityus stigmurus (TstiV). Materials and methodsThe latex of J. mutabilis (JmLa) was obtained through in situ incisions in the stem and characterized using HPLC-ESI-QToF-MS. Acute oral toxicity was investigated in mice. The protein profile of T. stigmurus venom was obtained by electrophoresis. The ability of latex to interact with venom components (TstiV) was assessed using SDS-PAGE, UV–Vis scanning spectrum, and the neutralization of fibrinogenolytic and hyaluronidase activities. Additionally, the latex was evaluated in vivo for its ability to inhibit local edematogenic and nociceptive effects induced by the venom. ResultsThe phytochemical profile of the latex revealed the presence of 75 compounds, including cyclic peptides, glycosides, phenolic compounds, alkaloids, coumarins, and terpenoids, among others. No signs of acute toxicity were observed at a dose of 2000 mg/kg (p.o.). The latex interacted with the protein profile of TstiV, inhibiting the venom's fibrinogenolytic and hyaluronidase activities by 100%. Additionally, the latex was able to mitigate local envenomation effects, reducing nociception by up to 56.5% and edema by up to 50% compared to the negative control group. ConclusionsThe latex of Jatropha mutabilis exhibits a diverse phytochemical composition, containing numerous classes of metabolites. It does not present acute toxic effects in mice and has the ability to inhibit the enzymatic effects of Tityus stigmurus venom in vitro. Additionally, it reduces nociception and edema in vivo. These findings corroborate popular reports regarding the antivenom activity of this plant and indicate that the latex has potential for treating scorpionism.

A comparative study of the biosynthesis of CuNPs by Niallia circulans G9 and Paenibacillus sp. S4c strains: characterization and application as antimicrobial agents

BackgroundBiosynthesis of metallic nanoparticles using microorganisms are a fabulous and emerging eco-friendly science with well-defined sizes, shapes and controlled monodispersity. Copper nanoparticles, among other metal particles, have sparked increased attention due to their applications in electronics, optics, catalysis, and antimicrobial agents.ResultsThis investigation explains the biosynthesis and characterization of copper nanoparticles from soil strains, Niallia circulans G9 and Paenibacillus sp. S4c by an eco-friendly method. The maximum reduction of copper ions and maximum synthesis CuNPs was provided by these strains. Biogenic formation of CuNPs have been characterized by UV–visible absorption spectroscopy, X-ray diffraction, Fourier transform infrared spectroscopy, X-ray analysis and transmission electron microscopy analysis. Using UV-visible spectrum scanning, the synthesised CuNPs’ SPR spectra showed maximum absorption peaks at λ304&308 nm. TEM investigation of the produced CuNPs revealed the development of spherical/hexagonal nanoparticles with a size range of 13–100 nm by the G9 strain and spherical nanoparticles with a size range of 5–40 nm by the S4c strain. Functional groups and chemical composition of CuONPs were also confirmed. The antimicrobial activity of the biosynthesized CuNPs were investigated against some human pathogens. CuNPs produced from the G9 strain had the highest activity against Candida albicans ATCC 10,231 and the lowest against Pseudomonas aeruginosa ATCC 9027. CuNPs from the S4c strain demonstrated the highest activity against Escherichia coli ATCC 10,231 and the lowest activity against Klebsiella pneumonia ATCC 13,883.ConclusionThe present work focused on increasing the CuNPs production by two isolates, Niallia circulans G9 and Paenibacillus sp. S4c, which were then characterized alongside. The used analytics and chemical composition techniques validated the existence of CuONPs in the G9 and S4c biosynthesized nano cupper. CuNPs of S4c are smaller and have a more varied shape than those of G9 strain, according to TEM images. In terms of antibacterial activity, the biosynthesized CuNPs from G9 and S4c were found to be more effective against Candida albicans ATCC 10,231 and E. coli ATCC 10,231, respectively.

Pyrogallol intermediates elicit beta-amyloid secretion via radical formation and alterations in intracellular trafficking, distinct from pyrogallol-generated superoxide

This study unveils a novel role of pyrogallol (PG), a recognized superoxide generator, in inducing beta-amyloid (Aβ) secretion in an Alzheimer's disease (AD) cellular model. Contrary to expectations, the analysis of dihydroethidium fluorescence and UV-VIS spectrum scanning reveals that Aβ secretion arises from PG reaction intermediates rather than superoxide or other by-products. Investigation into Aβ secretion mechanisms identifies dynasore-dependent endocytosis and BFA-dependent exocytosis as independent pathways, regulated by tiron, tempol, and superoxide dismutase. Cell-type specificity is observed, with 293sw cells showing both pathways, while H4sw cells and primary astrocytes from an AD animal model exclusively exhibit the Aβ exocytosis pathway. This exploration contributes to understanding PG's chemical reactions and provides insights into the interplay between environmental factors, free radicals, and AD, linking occupational PG exposure to AD risk as reported in the literature.

Tailoring the physicochemical properties of starch: impact of integrated ultrasonic and ethanol pretreatment on the oil uptake of infrared fried ginkgo seeds.

The structural changes of starch would have a more crucial impact on oil absorption and quality changes in starch-rich fruits and vegetables during frying process with enhanced heat transfer (such as infrared frying). In the present study, the influence of integrated ultrasonic and ethanol (US + ethanol) pretreatment on oil uptake in infrared fried (IF) ginkgo seeds was evaluated regarding modifications in the physicochemical properties of starch. The pretreatment was performed with ultrasonic (40 kHz, 300 W) and ethanol osmotic (95%, v/v) treatment individually or integrated for 40 min. The mass transfer in the pretreatment was facilitated by combined ultrasound and ethanol. The swelling power, solubility, and gelatinization degree of starch was significantly increased. Low-frequency-NMR curves and images revealed that the bound water fraction in ginkgo seeds was increased and the water distribution was homogenized. The results of Fourier transform-infrared spectrum and differential scanning calorimeter revealed that the crystalline regions of starch were reduced and the thermal enthalpy was decreased after US + ethanol pretreatment. The total, surface and structural oil content in IF ginkgo seeds with US + ethanol pretreatment was reduced by 29.10%, 34.52% and 29.73%, respectively. The US + ethanol pretreatment led to a thinner crust layer with increased porosity and smaller-sized pores in the IF ginkgo seeds as observed by stereo microscopy and scanning electron microscopy. The changes in structural and physicochemical properties of starch by combined ultrasound and ethanol affect the crust ratio and pore characteristics in fried high-starch fruits and vegetables, thereby reducing oil absorption. © 2024 Society of Chemical Industry.

Electron paramagnetic resonance study of the paramagnetic centers in gamma-irradiated 4-Nitrobenzaldehyde single crystal

4-Nitrobenzaldehyde (C7H5NO3) (4NB) single crystals were obtained by slow evaporation technique. Single crystals were made paramagnetic by irradiation with a 60Co-gamma rays. Electron Paramagnetic Resonance (EPR) Spectroscopy method was used to detect the radiation damage center formed in the single crystals. As a result of temperature scanning of EPR spectra at different temperatures between 120 and 470 K, it was found to be independent of temperature. That's why the EPR study was done only at 300 K. The radiation effect caused the formation of the 4NB anion radical in the 4NB single crystal. All the protons in the structure created hyperfine structure splittings. The principal values of the hyperfine structure constants resulting from the interaction of the unpaired electron with protons, the principal values of the g-tensor and their direction cosines were calculated.

Fe2+-NTA synergized UV254 photolytic defluorination of perfluorooctane sulfonate (PFOS): Enhancing through intramolecular electron density perturbation via electron acquisition

Perfluorooctane sulfonate (PFOS) is a persistent organic pollutant posing a risk in environmental persistence, bioaccumulation and biotoxicity. This study was to reach a comprehensive and deeper understanding of PFOS elimination in a UV254 photolytic treatment with the co-presence of Fe2+ and nitrilotriacetic acid trisodium salt (NTA). PFOS defluorination was noticeably enhanced in the UV/Fe2+-NTA treatment compared with UV/NTA, UV/Fe2+ and our previously studied UV/Fe3+ treatments. UV–vis, FTIR, and UPLC/MS-MS results indicated the formation of PFOS-Fe2+-NTA complex in PFOS, Fe2+ and NTA mixture. The transition energy gap of PFOS-Fe2+-NTA decreased below the excitation energy supplied by UV254 irradiation, corresponding with red shift appearing in UV–vis scanning spectrum. This favored intramolecular electron transfer from Fe2+-NTA to PFOS under UV254 irradiation to form electron-accepting PFOS. Molecular electrostatic potential and atom charge distribution analyses suggested electron density rearrangement and perturbation in the perfluorinated carbon chain of electron-accepting PFOS, leading to the decrease in bond dissociation energies. Intermediate products detection suggested the parallel defluorination pathways of PFOS desulfonation, middle carbon chain scission and direct C-F cleavage. NTA exhibited crucial functions in the UV/Fe2+-NTA treatment by holding Fe2+/Fe3+ in soluble form as a chelant and favoring water activation to generate hydrated electrons (eaq−) under UV irradiation as a photosensitizer. Fe2+ acting as the conduit for electron transfer and the bridge of PFOS anion and NTA was thought functioning best at 200 µM in this study. The degree of UV/Fe2+-NTA -synergized PFOS defluorination also depended on eaq− yield and UV254 photon flux. The structure dependence on the electron transfer process of PFOS and PFOA was explored incorporating molecular structure descriptors. Because of possessing greater potential to acquire electrons or less likeliness to donate its electrons than PFOA, PFOS exhibited faster defluorination kinetics in the published “reduction treatments” than “oxidation” ones. Whereas, PFOA defluorination kinetics were at similar level in both “reduction” and “oxidation” treatments.

Chemotaxonomic classification of closed-related sweet oranges (Citrus sinensis L.) using principal component and cluster analysis of color and bi-oactive compounds in the orange peels

Chemotaxonomy is a systematic approach to plant classification based on discernible variations and similarities in their biochemical compositions, with a particular emphasis on secondary metabolites that often exhibit specificity within taxonomically related plant species. In the context of our investigation, we conducted a comprehensive chemotaxonomic analysis of sweet oranges utilized in concentrated juice production. This involved a thorough examination of antioxidant activities, characterization of flavonoid and phenolic profiles, UV-visible spectra scanning, and the implementation of color analysis. The results from cluster analysis demonstrated the superior efficacy of color analysis in discerning subtle distinctions among orange varieties. Further refinement in the analytical process requires the application of supplementary techniques after an exhaustive and precise extraction facilitated by organic solvents. Notably, all employed methodologies successfully discriminated between distinct orange types. While the compilation of extensive datasets presents inherent challenges, the incorporation of Principal Component Analysis (PCA) and Hierarchical Cluster Analysis (HCA) enhances the interpretability of the obtained results. Considering that existing methodologies for assessing fresh fruit quality rely on subjective human visual inspection or orange juice analysis by ratio, which may lack precision in quantifying chemical constituents, there exists a growing demand for expedited techniques that can reliably ensure the quality of orange juice within the industry.

Drying shrinkage mitigation of alkali-activated blast furnace slag-copper slag by polyether-based shrinkage reducing admixture and MgO-based expansion agent

Volume stability is a critical challenge for the practical applications of alkali-activated materials. To mitigate the drying shrinkage of alkali-activated blast furnace slag-copper slag (AAS-CS), different contents of polyether-based shrinkage reducing admixture (PSRA) and MgO-based expansion agent (MEA) are used in this study. The effects of PSRA and MEA on the hydration process, mechanical property and drying shrinkage are investigated. Meanwhile, the mechanisms for drying shrinkage compensation of PSRA and MEA are deeply analyzed by nuclear magnetic resonance (NMR), Fourier transform infrared spectrum (FTIR), thermogravimetry and differential scanning calorimetry (TGA/DSC), X-ray diffraction (XRD) and scanning electron microscope (SEM). Results show that the drying shrinkage rate and the compressive strength of AAS-CS gradually decrease with the PSRA content increases from 0 to 2.0 wt%. This is mainly attributed to the coarser pore size and the lower surface tension caused by PSRA. When the content of MEA is 4.0 wt%, AAS-CS exhibits the lower drying shrinkage rate and the higher compressive strength in comparison with the reference sample. The addition of MEA promotes the formation of hydrotalcite (Ht). As an expansive product, an appropriate amount of Ht can exert the filling effect and the shrinkage compensating effect.

Heterologous overexpression of heat shock protein 20 genes of different species of yellow Camellia in Arabidopsis thaliana reveals their roles in high calcium resistance

Yellow Camellia (Camellia sect. chrysantha) is a rare ornamental plant and an important germplasm resource globally. Camellia nitidissima thrives in normal acidic soils, while Camellia limonia can adapt to the calcareous soils found in karst areas. Our previous study on the karst adaptation of yellow camellias revealed that the expression levels of heat shock protein 20(HSP20) were higher in Camellia limonia than in Camellia nitidissima. However, the functions of the HSP20 gene of Camellia limonia remain unclear to data. In this study, the HSP20 genes of Camellia limonia (ClHSP20-OE lines) and Camellia. nitidissima (CnHSP20-OE lines) were cloned and overexpressed heterologously in Arabidopsis thaliana. Additionally, we overexpressed the HSP20 gene of Arabidopsis (AtHSP20-OE lines) was also overexpressed, and the T-DNA inserted mutants (athspmutant lines) were also used to determine the functions of HSP20 genes. Under high calcium stress, the chlorophyll, nitrogen, water content and humidity of leaves were increased in ClHSP20-OE lines, while those of other lines were declined. The size of the stomatal apertures, stomatal conductance, and the photosynthetic efficiency of ClHSP20-OE lines were higher than those of the other lines. However, the accumulation of H2O2 and O2− in the leaves of ClHSP20-OE lines was the lowest among all the lines. Energy spectrum scanning revealed that the percentage of calcium on the surfaces of the leaves of ClHSP20-OE lines was relatively low, while that of athspmutant lines was the highest. The ClHSP20 gene can also affected soil humidity and the contents of soil nitrogen, phosphorus, and potassium. Transcriptome analysis revealed that the expressions of FBA5 and AT5G10770 in ClHSP20-OE lines was significantly up-regulated compared to that of CnHSP20-OE lines. Compared to that of athspmutant lines, the expressions of DREB1A and AT3G30460 was significantly upregulated in AtHSP20-OE lines, and the expression of POL was down-regulated. Our findings suggest that the HSP20 gene plays a crucial role in maintained photosynthetic rate and normal metabolism by regulating the expression of key genes under high-calcium stress. This study elucidates the mechanisms underlying the karst adaptation in Camellia. limonia and provides novel insights for future research on karst plants.

Influences of Graphene Oxide on Mechanical Properties and Mesoscopic Deformation and Failure Process of Concrete

In this research, graphene oxide (GO) was integrated into concrete to assess its effectiveness as an additive. Triaxial compression permeability experiments, variable‐angle (30°, 45°, and 60°) shear experiments, and dynamic compression experiments were conducted on graphene oxide concrete (GOC) and normal concrete (NC). The Holmquist–Johnson–Cook model and LS‐DYNA software were utilized to simulate the mesoscopic failure of NC and GOC under impact loading. The mechanism of GO was examined through scanning electron microscope (SEM) microscopic scanning and energy dispersive spectroscopy (EDS) energy spectrum testing. The findings demonstrate that the contain of GO significantly enhances the destruction resistance of concrete under triaxial compression. The permeability of both NC and GOC exhibits a negative exponential decrease with increasing confining pressure, and carbon fiber reduces concrete permeability by 17.79%–60.9%. Compared to NC, the cohesion and internal friction angle of GOC increased by 7.80% and 8.55%, respectively. GO also improves energy conversion and storage capacity during the elastic stage of concrete, reducing inelastic energy loss during shear processes. Although, both NC and GOC exhibit strain rate sensitivity, the DIF value of GOC surpasses that of NC and the disparity between the two intensifies with increasing impact pressure. Simulation results indicate that the number of crushing units in GOC is significantly lower than in NC, maintaining integrity. Analysis of SEM microscopic test results reveals that the distribution of cement hydration products in NC is uniform, whereas in GOC, it displays regional characteristics, a phenomenon corroborated by EDS energy spectrum test results.

Stability Improvement of the TDLAS-Based CO Monitoring Module in a Coal Mine by Using a Spectral Denoising Algorithm Based on SVR

CO gas is not only lethal but also a significant forecasting indicator for the spontaneous combustion of coal mines. It is imperative that monitoring modules for CO gas that work well in the coal mine environment are available. A feasible solution is the detection of CO by using monitoring modules based on tunable diode laser absorption spectroscopy (TDLAS) over a mid-infrared waveband near 4.6 μm. However, in most cases, the mid-infrared TDLAS-based CO monitoring module tends to introduce severe interference fringe noise into the TDLAS spectral backgrounds which is difficult to filter out using traditional spectral filtering methods, reducing the detection performance of the module. In order to filter out the noise and improve the stability of the module in complex coal mine environments, this work proposed an algorithm based on support vector regression (SVR) to extract the TDLAS spectral backgrounds. Spectral analysis indicates that the TDLAS spectral background can be predicted over the entire scanning spectrum range by using this algorithm, and the noise in the spectral background can be effectively filtered out when calculating the absorbance spectrum based on the Lambert–Beer law. Compared to extracting spectral backgrounds using the traditional least square polynomial fit, the obtained correlation coefficients between regression models of spectral backgrounds and corresponding training point datasets were increased from below 0.998 to above 0.999. The peak-to-peak value of the obtained N2 absorbance spectrum was suppressed below 0.022 from nearly 0.045. The signal-to-noise ratio of the obtained 25 ppm CO absorbance spectrum was increased to 13.35 from 6.95. A CO monitoring module polluted by dust was used to conduct experiments to further test the SVR-based algorithm. The experiment results showed that after programming the SVR-based algorithm to the module, the estimated limit of detection of the module was reduced to 5.46 ppm from 29.08 ppm, and all the absolute measuring errors of the standard CO gases with different low concentrations were reduced to less than 4 ppm from a majority of the errors of more than 10 ppm, compared to least square polynomial fit. The CO monitoring module could still maintain the performance of high-precision quantitative detection when using the SVR-based algorithm even if it had been polluted severely. So, the CO monitoring module has good adaptability to harsh field environments, and its operation stability can be effectively improved by using the algorithm proposed in this work.

Direct quantification of 1,1-dimethylhydrazine transformation products in sandy soil by thermal desorption gas chromatography – Tandem mass spectrometry

The use of rocket propellants based on unsymmetrical dimethylhydrazine (UDMH) in launch vehicles and boosters poses a threat to the environment due to the release of UDMH into soils and its subsequent transformation into a variety of nitrogen-containing compounds, including toxic and carcinogenic ones. The present proof-of-concept study proposes a novel approach to screening and simultaneous determination of a wide range of nitrogen-containing UDMH transformation products in soils, based on direct thermal desorption (TD) as a solvent-free sample extraction technique coupled with GC–MS/MS analysis.Optimal TD conditions consisting of the incubation of 5 mg sample at 300 °C for 30 min, allowed attaining high recoveries (80–100 %) for the most tested compounds and developing the method for quantification of fifteen acyclic and heterocyclic UDMH transformation products in sandy soil with LODs of 0.3–7.8 µg kg−1. The matrix matched calibration and introduction of the internal standard (pyridine‑d5) ensured high accuracy (75–100 %) and precision (RSD < 15 %) of the analysis. Along with high sensitivity and accuracy, the main advantages of the developed method are exceptional simplicity of sample preparation, low amount of toxic sample, high automation degree, and environmental friendliness.The developed method was successfully tested in the analysis of seven real soil samples taken from the Baikonur cosmodrome operational zone (Kazakhstan). The use of TD-GC–MS analysis in full spectrum scanning mode allowed for tentative identification of 62 UDMH transformation products including several compounds not yet described in the literature.

Fiber Bragg grating scanning spectral distortion caused by vibration in a rotor temperature monitoring system

To improve the accuracy of the rotor temperature monitoring system using the spatial coupling method, the vibration distortion of the scanning spectra was investigated theoretically and experimentally. Vibration causes a shifted reflection peak and a narrower 3 dB bandwidth. The maximum scanning error of the FBG center wavelength plummetes, decreases slowly, and finally stabilizes with increasing g (the ratio of the coupling loss period between the collimators to the scanning spectrum time). Coordinating the vibration frequency with the demodulator scanning frequency so that the g-value is greater than 10 is the key to improving the accuracy. The scanning error increases slowly and then rapidly as the radial vibration amplitude or the shaft tilt amplitude increases. As the axial ratio of the rotor trajectory increases, the error first soars and then stabilizes when the ratio reaches 2.5. It's also been found that using the centroid peak method helps reduce errors.

Effects of Tremella polysaccharide on frost resistance of frozen dough considering water state, physical property and gluten structure

To explore the effects of Tremella polysaccharide (TP) on frost resistance in dough, different concentrations of TP (0, 0.2, 0.4, 0.6, 0.8, and 1.0 %) were added to frozen dough, and the effects on the water state, physical property, and gluten structure of the dough were studied. The results showed that 0.6 % TP concentration caused a reduction in the freezable water content and growth rate of free water, and inhibited the recrystallization of ice in dough during frozen storage. The tensile test and rheological analysis results showed that 0.6 % TP concentration could significantly protect the tendons of dough and thus maintain its dominant elasticity. Free sulfhydryl group content determination and infrared spectrum scanning confirmed that 0.6 % TP concentration yielded the lowest transition of the ordered structure to a disordered structure in the dough and maintained the integrity of the dough gluten structure with minimal porosity. These findings indicate that TP can be used as a potent food cryoprotectant to mitigate the deterioration of frozen dough quality and has promising application prospects in the food industry.

Curing properties study on sucrose-melamine-formaldehyde resin

Melamine formaldehyde resin (MF) has a long history of about 90 years since its birth. Its industrial application, however, has been limited by the high cost of raw materials, high content of free formaldehyde and easy cracking of adhesive layer after curing. These problems can be solved by making use of biomass resources to modify MF in theory. Sucrose, melamine and formaldehyde were noted as the main raw materials for synthesizing sucrose-melamine-formaldehyde copolymer resin (SMF) under alkaline conditions. The effect of sucrose content and curing agent on the curing properties have been carried out through Fourier transform-infrared spectroscopy (FT-IR), nuclear magnetic resonance spectrum (NMR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The findings show that the SMF curing behavior was an exothermic process, which was achieved by the dehydration synthesis between hydroxymethyl groups. The sucrose content had a large effect on the thermal stability and the curing behavior of SMF, and the addition of curing agent promoted the resin curing. Not only was the thermal stability decreased, but also the curing reaction was more difficult to occur with the sucrose addition. The sucrose molecules participated in the curing process through chemical bonding, and then formed a stable network structure for the resin system.

Adsorption and Degradation of Organics in Wastewater on Municipal Sludge.

Adsorption and degradation of organic compounds on sludge were investigated by comparing activated and inactivated sludge at various dosages, pH values, and temperatures. The organic compounds in wastewater were identified and evaluated through fluorescence spectra. The results show that optimum adsorption occurred as the activated and inactivated sludge concentration was 4000 mg/L at a pH of 7.99 and a temperature of 30 °C. The fluorescence scanning spectrum indicated that activated sludge could remove protein-like organic matter, fulvic acid-like organic matter, and humic acid-like organic matter by 22.1, 9.4, and 41.2%, respectively, via adsorption only or by 25.9, 9.8, and 74.3%, respectively, via adsorption and degradation. Under optimum conditions, by using the good adsorption performance of sludge combined with other sewage treatment technologies, the treatment of high-content organic wastewater can be achieved.

The hydrothermal performance and corrosion resistance of MgO@Nb2O5 composite coatings on Mg–7Y alloy in natural seawater

MgO@Nb2O5 composite coating was prepared on the surface of Mg–7Y alloy by micro-arc oxidation technique. The microstructure of the composite coatings was tested by scanning electron microscopy, energy spectrum analysis, X-ray diffraction and scanning kelvin probe force microscope. The hydrothermal performance and corrosion resistance of MgO@Nb2O5 composite coatings were analyzed by electrochemistry tests and laser confocal. The results showed that microspore diameter, porosity and roughness of the composite coatings were all decreased with the increasing of Nb2O5 concentration. The micro-arc oxidation composite coatings were mainly composed of MgO and Nb2O5. Compared with the micro-arc oxidation coating without Nb2O5, the corrosion voltage of the micro-arc oxidation coating with Nb2O5 was increased and the corrosion current was reduced. The corrosion resistance of Mg–7Y alloy was effectively improved by the MgO@Nb2O5 composite coatings, and the best corrosion resistance of the micro-arc oxidation coating was achieved when the Nb2O5 concentration was 2 g/L. The hydrothermal test demonstrated that the hydrothermal resistance of the coatings was significantly improved due to the addition of Nb2O5.