Scanning Fiber Probe Research Articles

A miniaturized pre-calibration based Lissajous scanning fiber probe for endoscopic optical coherence tomography

In this paper we present a miniaturized pre-calibration based forward-viewing Lissajous scanning fiber probe for endoscopic optical coherence tomography (OCT). The probe is based on an asymmetric fiber cantilever driven by the piezoelectric bender to realize the two-dimensional (2D) Lissajous scanning, which can realize a relatively large scanning range under a low driving voltage. A capillary metal tube is mounted at the end of the main fiber to reduce the resonant frequency of the fiber cantilever. The relationship between the filling rate and the side-lobe number of the Lissajous scanning pattern is studied, and a method of selecting the orthogonal resonant frequency of the Lissajous scanning is proposed. Through the numerical simulation by COMSOL software, the structural parameters of the asymmetric fiber cantilever are determined. The orthogonal resonant frequencies of the asymmetric fiber cantilever are 169 Hz and 122 Hz. The lengths of the main imaging fiber, the auxiliary fiber and the metal capillary tube are 15.94 mm, 4.49 mm and 2 mm, respectively. The probe is fully packaged in a metal tube for endoscopic imaging. The focal spot and the working distance are 25 µm and 5 mm, respectively. The field of view is larger than 1.5 mm × 1.5 mm. The total rigid length and the outer diameter of the probe are 35 mm and 3.5 mm, respectively. The stability and repeatability of the Lissajous scanning trajectory, and the imaging stability with the rotation of the probe are investigated and verified. The probe is incorporated into a 50 kHz swept source OCT system. The axial resolution of the endoscopic OCT is 10.3 μm, and the imaging frame rate is 1 FPS (frames per second). The maximum signal-to-noise ratio of the imaging system is 110 dB. The imaging performance of the probe is validated by the 2D <i>en-face</i> and three-dimensional volumetric OCT imaging of the high scattering sample and the biological tissue. The probe can be used for the endoscopic imaging of the human tooth. From the result we can distinguish the dental enamel, dental essence and the dental calculus. The developed forward-viewing Lissajous scanning fiber probe is expected to be used in dental applications such as early calculus detection.

Early-photon reflectance fluorescence molecular tomography for small animal imaging: Mathematical model and numerical experiment.

The paper presents an original approach to time-domain reflectance fluorescence molecular tomography (FMT) of small animals. It is based on the use of early arriving photons and state-of-the-art compressed-sensing-like reconstruction algorithms and aims to improve the spatial resolution of fluorescent images. We deduce the fundamental equation that models the imaging operator and derive analytical representations for the sensitivity functions which are responsible for the reconstruction of the fluorophore absorption coefficient. The idea of fluorescence lifetime tomography with our approach is also discussed. We conduct a numerical experiment on 3D reconstruction of box phantoms with spherical fluorescent inclusions of small diameters. For modeling measurement data and constructing the sensitivity matrix we assume a virtual fluorescence tomograph with a scanning fiber probe that illuminates and collects light in reflectance geometry. It provides for large source-receiver separations which correspond to the macroscopic regime. Two compressed-sensing-like reconstruction algorithms are used to solve the inverse problem. These are the algebraic reconstruction technique with total variation regularization and our modification of the fast iterative shrinkage-thresholding algorithm. Results of our numerical experiment show that our approach is capable of achieving as good spatial resolution as 0.2 mm and even better at depths to 9 mm inclusive.

Miniaturized precalibration-based Lissajous scanning fiber probe for high speed endoscopic optical coherence tomography.

We present a miniaturized precalibration-based forward-viewing Lissajous scanning fiber probe for high speed endoscopic optical coherence tomography (OCT). The probe is based on an asymmetric fiber cantilever driven by the piezoelectric bender to realize two-dimensional (2D) Lissajous scanning. The stability and repeatability of the Lissajous scanning trajectory of the probe is tested by a position sensitive detector (PSD)-based position calibration setup. The two orthogonal resonant frequencies of the cantilever are measured to be 167.2 and 121 Hz. A 25 µm focal spot is formed at the working distance of 5 mm by the graded-index (GRIN) lens, and the field of view of the imaging probe is around ${1.5}\;{\rm mm} \times {1.5}\;{\rm mm}$1.5mm×1.5mm. The probe is fully packaged in a hypodermic tube for endoscopic imaging. The total rigid length and outer diameter are 35 mm and 3.5 mm, respectively. The probe is incorporated in a 50 KHz swept source OCT system with the axial resolution of 14 µm, and its imaging performance is validated by the 2D en face and 3D volumetric OCT imaging of the phantom and the biological tissue.

Spectral anomalies and Gouy rotation around the singularity of ultrashort vortex pulses.

Spectral anomalies of femtosecond pulses with orbital angular momentum were studied in the vicinity of singularities. Bessel-Gauss (BG) beams were generated with mode-locked Ti:sapphire oscillators and dispersion-compensated diffractive axicons acting as spiral phase plates (SPPs). High-resolution two-dimensional spectral mapping was performed with a scanning fiber probe. Progressive rotation of the most pronounced features, known as "spectral eyes", in the maps of spectral moments was found at increasing propagation distance. The phenomenon is explained by a wavelength-dependent Gouy phase shift of interfering spectral components in the twisted wavefront. Spatial "spectral switching" was detected for few-cycle pulses. Possible improvements of selectivity are proposed.

内窥式二维光纤扫描探头及其驱动方法

An endoscope scanning fiber probe was designed to perform two-dimensional(2D) scanning for optical coherence tomography based on the PZT.Two piezoelectric ceramic and a thin conductive substrate were used to drive the optical fiber probe.The probe used the cantilever resonance of optical fiber cantilever,imposed the mixing signals which closed to the resonant frequency of optical fiber on the piezoelectric ceramic,and also stimulated two orthogonal directions vibration of fiber cantilever to achieve two-dimensional scanning.Theoretical model was established and took the finite element simulation analysis was carried out.A practical model was made to carry out experiments and otain the scan pattern.The experimental results realize the optical fiber cantilever two dimensional scanning,and the scanning scope reaches(500×500)μm,adjusting drive signal amplitude can change the scanning range.The theoretical analysis and the simulation was consistent,and verified the feasibility of the scheme.

Distance Dependent Spectral Tuning of Two Coupled Metal Nanoparticles

The spectral properties of two spherical metallic nanoparticles of 80 nm in diameter are examined with regard to the interparticle distance and relative polarization of the excitation light. One Au nanoparticle is attached to a scanning fiber probe and the second to a scanning substrate. This configuration allows three-dimensional and arbitrary manipulation of both distance and relative orientation with respect to the incident light polarization. As supported by numerical simulations, a periodic modulation of the coupled plasmon resonance is observed for separations smaller than 1.5 microm. This interparticle coupling affects the scattering cross section in terms of spectral position and spectral width as well as the integral intensity of the Mie-scattered light.

Laser Terahertz Emission Microscope

Developments of laser terahertz (THz) emission microscope (LTEM) systems are reviewed. Femtosecond lasers can excite the THz wave emission from various electronic materials, such as semiconductors, high-temperature superconductors, manganites, multiferroic oxides, etc., due to ultrafast current modulation. Limiting the topic to semiconductors, the current modulation is realized by acceleration or deceleration of photoexcited carriers due to the local electric field extrinsically or intrinsically induced at the laser illumination spot. Thus, LTEM has a potential to visualize the local electric field distribution and photoresponse without any contacts or damages. We have ever constructed prototype free-space type and scanning fiber-probe (SFP) type LTEM systems with transmission or reflection mode. The system performance of the SFP-LTEM has been greatly improved compared with that for the prototype one. The spatial resolution of the SFP-LTEM system has a minimum spatial resolution less than 3 mum , which is defined by the laser beam diameter. The compact SFP-LTEM system, in particular the reflection system, has the potential to be utilized for wide applications as well as various materials. In this review paper, we introduce the details of the LTEM systems and example applications for the evaluation of electric field distribution in integrated circuits and supercurrent distribution in high-temperature superconductors.

Direct observation of self-focusing near the diffraction limit in polycrystalline silicon film

We present direct observation of self-focusing near the diffraction limit by measuring the beam-spot size with a scanning fiber probe tip. We have used the polycrystalline silicon film, which exhibits a reverse-saturation (Im χ(3)≈8×10−3 esu) and self-focusing (Re χ(3)≈2×10−2 esu), as measured by the conventional z-scan method with He–Ne laser. It is observed that the beam radius of about its wavelength becomes smaller as the input laser intensity is increased, which indicates that the self-focusing effect dominates over the reverse saturation in the 300-nm-thick sample.