Scanning Electron Microscopy-energy Dispersive Spectroscopy Research Articles

High-Temperature Cyclic Oxidation Behavior and Microstructure Evolution of W- and Ce-Containing 18Cr-Mo Type Ferritic Stainless Steel

Due to the recurrent starting and stopping operations of automobiles during service, their engines’ hot ends are continually subjected to high-temperature cyclic oxidation. Therefore, it is crucial to develop ferritic stainless steels with better high-temperature oxidation resistance. This study focuses on improving the high-temperature cyclic oxidation performance of 18Cr-Mo (444-type) ferritic stainless steel by alloying with high-melting-point metal W and the rare earth element Ce. For this purpose, a high-temperature cyclic oxidation experiment was designed to simulate the actual service environment and investigate the high-temperature cyclic oxidation behavior and microstructure evolution of 444-type ferritic stainless steel alloyed with W and Ce. The oxide structure and composition formed during this process were analyzed and characterized using scanning electron microscopy/energy dispersive spectroscopy (SEM-EDS) and electron probe X-ray micro-analyzer (EPMA), in order to reveal the mechanism of action of W and Ce in the cyclic oxidation process. The results show that 18Cr-Mo ferritic stainless steel alloyed with W and Ce exhibits an excellent resistance to high-temperature cyclic oxidation. The element W can promote the precipitation of the Laves phase between the matrix and the oxide film, and the small-sized Laves phase can inhibit the interfacial diffusion of oxidation reaction elements and prevent the inward growth of the oxide film. The element Ce can refine oxide particles and reduce the thickness of the oxide film. CeO2 particles within the oxide film can serve as nucleation sites for the formation of oxide particles from reactive elements, and they also contribute to pinning the oxide film, thereby enhancing its adhesion.

Direct carbonation of porous materials produced from self-hardened paper mill fly ash

A high-Ca fly ash generated from a paper mill using a fluidized bed boiler was used as the potential medium to sequester CO2 via the direct carbonation process. In this study, the fly ash samples were exposed to accelerated carbonation to produce hardened pastes. The influence of the porosity controlled by the amount of foam in the matrix for maximizing CO2 sequestration was determined. The effect of porosity on carbonation was evident. The samples prepared with 40 % foam and a water-to-fly ash ratio of 0.79 recorded porosities of 56.1 % (carbonated) and 66.8 % (naturally carbonated (NC)) with the lowest mechanical strength of 2.1 and 1.1 MPa, respectively. These naturally carbonated (NC) samples have been cured naturally without using high CO2 pressure. Meanwhile, the samples prepared with 10 % foam and a water-to-fly ash ratio of 0.5 recorded porosities of 41.1 % (carbonated) and 52.9 % (NC) with the highest strength at 10.2 and 4.6 MPa, respectively. The highest carbonation efficiency determined by thermogravimetric analysis was obtained from the carbonated samples with 40 % foam. Scanning electron microscopy–energy-dispersive spectroscopy depicted the areas with high Al/Si content but low Ca–O content (dark areas) and carbonated areas with high Ca–O content (bright areas). Mercury intrusion porosimetry was used to determine the pore size distribution, whereby the samples were dominated by large capillary pores, resulting in their high porosity in this study.

In-Situ Synthesis of CuO/TiO2 Nanocomposite Onto Amine Modified Cotton Fabric for Antibacterial Durability and UV Protection

ABSTRACT In this research work, we explore antibacterial activity and the UV-protection of cotton fabric functionalized with copper oxide-titanium dioxide nano composites particles (CuO+TiO2 NCPs). Cotton fabrics (Cot) were treated with L-methionine (Am) and functionalized with bimetallic CuO+TiO2 NCPs by pad and rolling technique. Cu(NO3)2 and titanium isopropoxide (TIP) were used as sources of Cu(OH)2 and TiO2 colloid respectively, which were then converted into CuO and TiO2 nanoparticles (NPs) for making antibacterial and UV-protective cotton. The method yielded a crystallite size of CuO and TiO2 NPs of 18.09 and 32.5 nm, respectively. FTIR, Raman spectroscopy, High-resolution scanning electron microscopy-Energy dispersive Spectroscopy (HRSEM), (EDS), X-ray photo spectroscopy (XPS), thermal gravimetric analysis (TGA), and XRD were used to analyze the functional group, morphology, chemical composition, thermal stability and crystalline structure of the functionalized cotton fabric samples. The results showed that an esterification reaction occurred between Am and OH in cotton fabric, which further enhanced the binding of NCPs. AmCot-CuO+TiO2 NCPs exhibit outstanding antibacterial activity against gram-positive S. aureus and gram-negative E. coli. The UV protection factor (UPF) for AmCot-CuO+TiO2 NCPs reached 50+; thus, multifunctional cotton fabrics with excellent antibacterial and anti-ultraviolet properties were obtained.

Preparation, characterization and photocatalytic studies of defect pyrochlore, KMn0·33Te1·67O6 and its composite with g-C3N4

Skeletal materials belonging to the defect pyrochlore family have been the subject of considerable interest due to their remarkable properties. In this work, a highly efficient, stable and visible light active composite photocatalytic system consisting of defect pyrochlore of composition KMn0·33Te1·67O6 (KMnTeO) and g-C3N4 (g-CN) has been successfully prepared by simple physical mixing of pre-prepared KMnTeO and g-CN components synthesized in solid state and thermal treatment of low-cost melamine, respectively. Structural, morphological and optical properties of as-prepared catalysts were deduced from powder X-ray Diffraction (XRD), Fourier Transform Infrared (FT-IR), Raman, Field Emission Scanning Electron Microscopy-Energy Dispersive X-ray Spectroscopy (FESEM-EDX), Transmission Electron Microscopy-High Resolution Transmission Electron Microscopy (TEM-HRTEM), Ultraviolet–Visible Diffuse Reflectance Spectroscopy (UV–Vis DRS), X-ray Photoelectron Spectroscopy (XPS) and Photoluminescence (PL) measurements. The lattice parameter “a” of parent KMnTeO was obtained from Rietveld refinement of its powder XRD pattern. The FT-IR and Raman spectra of KMnTeO gave characteristic bands belonging to the defect pyrochlore structure. The photocatalytic activities of KMnTeO and composite KMnTeO-g-CN were evaluated by the degradation of methylene blue (MB). Scavenger experiments were carried out to identify the reactive species responsible for the degradation of MB. Furthermore, the reusability and stability of the photocatalysts were explored. The probable photocatalytic mechanism for MB degradation over the composite KMnTeO-g-CN was surmised according to the scavenger experiments. The work provides a new approach for the development of novel defect pyrochlore based composite photocatalysts to treat industrial wastewater containing organic pollutants.

Catalytic upgrading of Naomaohu coal pyrolysis volatiles over NiAl and NiLiAl oxides

Catalytic upgrading of volatiles is an essential technology to improve the product distribution of pyrolysis for the clean and efficient utilization of low-rank coals. In this work, novel acid-base bifunctional catalysts composed of Ni/Li/Al oxides were designed and prepared using LDH precursors with tunable chemical composition and structural properties. The catalysts were systematically characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), physisorption, NH3-temperature programmed desorption (NH3-TPD), CO2-temperature programmed desorption (CO2-TPD), H2-temperature programmed reduction (H2-TPR), and scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS). A two-stage fixed bed reactor was employed to evaluate the performance of the catalysts. Characterization results suggest that the crystal size of NiO and the surface area of the catalyst decreased with increasing Li content and decreasing Ni content in the catalyst, while the pore volume and pore diameter were positively correlated with Li content. Moreover, the addition of Li reduced the amount of weak acid sites and raised the amount of total basic sites. Consequently, the bifunctional catalysts boosted the yield of light tar and the contents of aromatics and phenols in tar. Specifically, with the highest total acid sites (569 μmol/g) promoting the cracking of heavy pitch components, Ni2.5Li0.5Al1 decreased the content of pitch in tar to 23.8 wt%, representing a 42.7 % drop from the corresponding non-catalytic pyrolysis. Accordingly, it improved the light tar yield to 7.2 wt%, which was 18 % higher than non-catalytic pyrolysis. 450 °C is identified as a suitable temperature for the catalytic upgrading of volatiles from Naomaohu coal; higher catalysis temperatures at 500 °C and 550 °C led to lower tar yield and lower phenols content, along with higher gas yield and more carbon deposition.

Effect of ZrO2 on the phase relations for CaO-SiO2-TiO2 system related to efficient extraction of titanium from titania-bearing slag

The selective crystallization and phase separation process has been regarded as a promising process for the recycling of titanium from titania-bearing furnace slag, however, the composition modification mechanism still remains unclear due to the lack of fundamental thermodynamic data. In the present work, the influence of ZrO2 addition on the equilibrium phase relations and the 1400 °C isotherm for CaO-SiO2-TiO2 system were experimentally determined by using the high temperature equilibration-quenching technique, and Scanning Electron Microscopy-Energy Dispersive X-ray Spectrometry, and X-ray diffraction analysis. The equilibrium solid phases of rutile (TiO2), perovskite (CaTiO3), and tridymite (SiO2) are determined to be coexisting with the liquid phase. In addition, comparisons of present results with thermodynamic calculation by FactSage show significant discrepancies. The present work is important for enriching the thermodynamic database of titania-bearing slag oxide systems as well as optimizing the selective crystallization and phase separation process.

Mining Metal‐Biomolecular Framework/PANI Composite CO Sensor: Material Synthesis, Gas Sensing Performance and Mechanism

AbstractIn addressing the issue of poor gas sensitivity in semiconductor CO sensor materials used in mining, such as pure PANI. This study utilized an ice‐water bath in combination with an in‐situ polymerization method to synthesize a new composite material consisting of Cu(II)‐racemic glutamate nanofibers and PANI. The morphology, structure, and chemical bonds of the composite material were analyzed using scanning electron microscopy‐energy dispersive spectroscopy (SEM‐EDS) and spectral analysis. The material's ability to detect CO (100–500 ppm) at room temperature was investigated, revealing a response value of up to 6.8 % for 400 ppm CO detection when the composite material was deposited on a ceramic interdigital electrode. The material exhibited good selectivity and responsiveness to CO detection at room temperature, attributed to the heterojunction formed between Cu(II)‐racemic glutamate nanofibers and PANI, which enhanced carrier migration. Consequently, the Cu(II)‐racemic glutamate nanofiber/PANI composite(Cu(II)‐RGlu/PANI) material shows promise as a high‐performance sensing material for CO detection at room temperature and as a low‐power, integrable sensor material for underground coal mines. This research contributes to the development of a theoretical framework for such applications.

Exploring the provenance of a Byzantine excavated assemblage of textile and leather finds by the application of instrumental analysis

Stereomicroscopy, Scanning Electron Microscopy-Energy Dispersive Spectroscopy (SEM–EDS), Fourier Transform Infrared spectroscopy with Attenuated Total Reflectance probe (FTIR-ATR), High Performance Liquid Chromatography with a Photodiode Array system (HPLC–PDA), X-ray Fluorescence spectroscopy (XRF), Zooarchaeology by Mass Spectrometry (ZooMS), and 14C dating were applied to an assemblage of textile and leather fragments that belong to the collection of the Byzantine & Christian Museum of Athens in Greece and lacked inventory information.The analyses applied, along with bibliographical research, yielded information on the materials, techniques and provenance of the find. The assemblage of finds consists of a gold thread embroidered silk satin, dyed with shellfish-purple; a gold strip-drawn wire embroidered silk tabby; a gold strip-drawn wire and red silk thread tapestry; a gold-thread embroidery on a tabby background; fragments of braided cord; and leather fragments. The material components could have been produced locally, in the area of the Byzantine Empire, though some of them indicate connections with India and/or China. The assemblage, dated between the mid AD 10th and mid eleventh century, was probably found in 1924 by Andreas Xygopoulos during the excavation of a tomb inside the church of Agia Sophia in Thessaloniki, Greece.

Simple distance-based thread analytical device integrated with ion imprinted polymer for Zn2+ quantification in human urine samples.

This article presents the development of a distance-based thread analytical device (dTAD) integrated with an ion-imprinted polymer (IIP) for quantitative monitoring of zinc ions (Zn2+) in human urine samples. The IIP was easily chemically modified onto the thread channel using dithizone (DTZ) as a ligand to bind to Zn2+ with methacrylic acid (MAA) as a functional monomer and ethylene glycol dimethacrylate (EGDMA) as well as 2,2-azobisisobutyronitrile (AIBN) as cross-linking agents to enhance the selectivity for Zn2+ detection. The imprinted polymer was characterized using Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) spectroscopy and Scanning Electron Microscopy-Energy Dispersive X-ray Spectroscopy (SEM-EDS). Under optimization, the linear detection range was from 1.0 to 20.0 mg L-1 (R2 = 0.9992) with a limit of detection (LOD) of 1.0 mg L-1. Other potentially interfering metal ions and molecules did not interfere with this approach, leading to high selectivity. Furthermore, our technique exhibits a remarkable recovery ranging from 100.48% to 103.16%, with the highest relative standard deviation (% RSD) of 5.44% for monitoring Zn2+ in human control urine samples, indicating high accuracy and precision. Similarly, there is no significant statistical difference between the results obtained using our method and standards on zinc supplement sample labels. The proposed method offers several advantages in detecting trace Zn2+ for point-of-care (POC) medical diagnostics and environmental sample analysis, such as ease of use, instrument-free readout, and cost efficiency. Overall, our developed dTAD-based IIP method holds potential for simple, affordable, and rapid detection of Zn2+ levels and can be applied to other metal ions' analysis.

Microstructural characterization and corrosion behaviour of heat treated standard stainless steels in tar sand

This paper aims to investigate the corrosion behaviour of heat-treated standard duplex stainless steel (UNS S32205) in the recovery of bitumen from Nigerian-rich tar sand, using sodium hydroxide (NaOH) as the process solution. Appropriate material family needs to be identified for the exploitation of tar sand resources to ensure sustainable extraction of bitumen. UNS S32205 offers exceptional mechanical properties and excellent corrosion resistance which makes it a great material choice for demanding applications, including offshore platforms and construction projects. Samples of UNS 32205 were heat-treated and immersed in the digested tar sand, maintaining a process temperature of 90°C. The microstructure of the corrosion coupons was studied using SEM/EDS (Scanning Electron Microscope/Energy Dispersive Spectroscope), and the corrosion rate of the samples was derived using gravimetric technique following ASTM G31 standard. The SEM micrographs indicated varying degrees of pits associated with the passivity of UNS 32205 and an imbalance between its ferrite and austenite phases due to the presence of secondary precipitates formed during heat treatment.The normalized sample, having a corrosion rate of 0.053 mm/year, exhibited the best corrosion resistance, followed by oil quenching (0.054 mm/year), then annealing (0.076 mm/year), and water quenching (0.077 mm/year), where they all showed improved corrosion resistance over the as-received sample having a corrosion rate of 0.078 mm/year.

Provenance of the Bronze Age lapis lazuli pieces from the Early Urban Center of Konar Sandal, Jiroft, Southern Iran

The sources of lapis lazuli objects found in the Bronze Age of the Iranian Plateau and its trade routes have been a subject of interest and a research question. Four archaeological pieces of lapis lazuli recovered from a stone-working workshop in the Bronze Age site of Konar Sandal South (Jiroft Plain), southern Iran, were analyzed using X-ray diffraction (XRD) and scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS) techniques to characterize the mineralogical composition and the possible provenance of raw materials. Results showed that these objects are identical based on their composition, presenting diopside and specific trace element proportions as provenance markers. Comparison with available data from Iranian archaeological sites and ancient resources from Central Asia revealed that these finds may have been imported from lapis lazuli mines located at Badakhshan in Afghanistan, as they were supplied raw materials for ancient lapis lazuli objects of Iran.

Effects of pyrite, quartz and sodium sulfite on roasting of a refractory sulfide concentrate and gold, silver, copper leaching during cyanidation

The oxidation roasting pretreatment process, which is a mature and dominant industrial practice for treating complex polymetallic gold deposits, has a low recovery of associated silver and exhibits an unclear reaction sequence. This study takes a silver-containing gold ore as the research object and investigates the effect of (i) sodium sulfite as an additive, (ii) main gold-bearing mineral pyrite, and (iii) gangue mineral quartz, on silver during the roasting process in roasting and leaching tests. Characterization techniques included scanning electron microscopy–energy dispersive spectroscopy analysis, and thermogravimetry–differential scanning calorimetry analysis. The results based on thermodynamic calculations and characterization show that the main reason for the low extraction of silver is that the calcined product (i.e., iron silicate) formed by the reaction between pyrite and quartz during the roasting process is mutually absorbed and wrapped with silver oxide. In addition, silver minerals decompose some iron sulfides and iron oxides under high-temperature conditions, promoting the reaction of iron and quartz to form iron silicate while strengthening the secondary encapsulation of silver by products of roasting, thus deteriorating the extraction of silver. The addition of sodium sulfite reduces the formation of iron silicate and increases the extraction of silver by directly promoting the conversion of pyrite to iron oxide. This study provides a theoretical basis for further improving the roasting and leaching of silver.

Effect of ligand interactions within modified granular activated carbon (GAC) on mixed perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) adsorption

A new adsorbent based on commercial granular activated carbon (GAC) and loaded with Cu(II) (GAC-Cu) was prepared to enhance the adsorption capacity of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS). The surface area (SA) and pore volume of GAC-Cu decreased by ∼15% compared to those of pristine GAC. The scanning electron microscopy–energy dispersive spectrometry (SEM-EDS) and leaching test results indicated that, compared with GAC, the Cu atomic ratio and Cu amount in GAC-Cu increased by 2.91 and 2.43 times, respectively. The point of zero charge (PZC) measured using a salt addition method obtained a pH of 6.0 (GAC) and 5.0 (GAC-Cu). According to the isotherm models obtaining highest coefficient of determination (R2), GAC-Cu exhibited a 20.4% and 35.2% increase for PFOA and PFOS in maximum uptake (qm), respectively, compared to those of GAC. In addition, the adsorption affinity (b) for GAC-Cu increased by 1045% and 175% for PFOA and PFOS, respectively. The pH effect on the adsorption capacity of GAC-Cu was investigated. The uptake of PFOA and PFOS decreased with an increase in pH for both GAC and GAC-Cu. GAC-Cu exhibited higher uptake than GAC at pH 6 and 7, but no enhanced uptake was observed at pH 4.0, 5.0, and 8.5. Therefore, ligand interaction was effective at weak acid or neutral pH.

Shear strength characterization and sustainability assessment of coal bottom ash concrete

The present study investigated the synergistic influence of coal bottom ash (CBA) on the shear strength of concrete. CBA was milled for 2, 6, and 10 h to form grinded CBA (GCBA). “L” shaped specimens were prepared with 10%–30% GCBA and 25%–50% CBA as alternative of Portland cement and natural fine aggregates. Concrete containing 20% GCBA (grinded for 6 h) and 25% CBA reported the highest shear strength owing to pozzolanic reactiveness and filler action. X-ray diffraction, scanning electron microscopy–energy-dispersive spectroscopy and Fourier transform infrared also supported the experimental outcomes. Well fitted mathematical models were derived followed by optimization using desirability function approach recommending 5.71 h of grinding, 26.27% GCBA, and 36.69% CBA as the optimum amount for its successful utilization in concrete. This approach further leads to significant reduction of about 22% in carbon footprints and eco-costs in comparison to conventional concrete.

Synthesis and characterization of chitosan-based pH-sensitive biofilm: An experimental design approach for release of vitamin B12

Hydrogels because of their unique potentials, such as highwater content and hydrophilicity, are of interest for the controlled release of drug molecules. In the present study, a biofilm was produced using chitosan, a natural polymer. Characterization analyses of the synthesized biofilm were performed using Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis-differential thermal analysis, x-ray diffraction, and scanning electron microscopy-energy dispersive x-ray spectrometry. The analysis results of the film before loading were compared to the analysis made after adding vitamin B12 to the film. The release percentage of vitamin B12 was investigated by using ultraviolet-visible spectrophotometery. The FT-IR bands of vitamin B12 were in the range of 2,800-3,500 cm-1 and 1,000 cm-1-1,750 cm-1. When pH increased from 3 to 7, release of vitamin B12 from the biopolymer increased up to pH 5. While examining the release potential, parameters, such as pH, initial concentration of vitamin B12, release time, and solution volume, were optimized by using response surface methodology. It was determined that with the increase in release time and the initial concentration, pH contributed positively to the release of vitamin B12. The following conditions were determined for release of vitamin B12 from the biofilm: pH: 4.2, initial concentration of vitamin B12: 54.0 mg L-1, the release time: 117 min, and volume of solution: 2.1 mL. The analysis of variance results showed that the determination coefficients for the use of synthesized biofilm in vitamin B12 release were high and R2 =0.9704.

High entropy (HfTiZrVNb)B2 ceramic particulate reinforced Al matrix composites: Synthesis, mechanical, microstructural and thermal characterization

This study aims to introduce a novel type of particulate reinforced Al matrix composite. High entropy (HfTiZrVNb)B2 ceramic particulate reinforced Al matrix composites were produced via a combined process of different powder metallurgy methods. Firstly, boride compounds (HfB2, TiB2, ZrB2, VB2, NbB2) were synthesized in the laboratory scale using the related metal oxide, boron oxide, and magnesium by mechanochemical synthesis (MCS) and leaching processes under optimum conditions. Secondly, the synthesized and purified boride powders were mixed in equimolar ratios using a planetary ball mill for 72 h, and they were sintered at 2000 °C under 30 MPa via spark plasma sintering (SPS). Thirdly, equimolar high entropy (HfTiZrVNb)B2 bulks were crushed, converted into powder forms, and added into Al powders at different amounts as 1, 2, 5, 10, and 15 wt %. Lastly, these powder blends were mechanically alloyed in a vibratory ball mill for 6 h, cold pressed and pressureless sintered at 630 °C for 2 h. For characterization techniques, X-ray diffractometry (XRD), thermal analysis, scanning electron microscopy/energy dispersive spectrometry (SEM/EDS), density measurements using pycnometer and Archimedes' methods, microhardness and dry sliding wear tests were conducted on the sintered composites. The highest hardness (∼1.5 GPa) and the lowest wear rate (∼0.0012 mm3/Nm) were obtained in the Al-15 wt % (HfTiZrVNb)B2 sample.

High Valency of Charge Compensator (Mo6+) to Substitute Ti Site in REE Doped Zirconolite (REE=Nd, Sm, Gd, Ho and Yb): Solid Solubility, Phase Evolution and Structural Analysis

Zirconolite ceramics have been proven to be a promising matrix for high-level waste immobilization, especially for minor actinides. In this study, a series of CaZr1-2xREE2xTi2-xMoxO7 (REE = Nd, Sm, Gd, Ho, Yb) samples were prepared to investigate the formation of zirconolite REE as surrogates of minor actinides and Mo6+ as charge compensator. Synchrotron and in-house powder X-ray diffraction (XRD), X-ray absorption near edge spectroscopy (XANES), and scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX) were used to study their solid solubility, phase evolution, and structural details. XRD results show that the formation of zirconolite-2M can be up to x=0.15 in the CaZr1-2xNd2xTi2-xMoxO7 samples when co-existence of 2M and 4M was observed at x=0.20 and 0.25. The “yellow phase” appears when x exceeds 0.4. The phase evolutions of CaZr1-2xSm2xTi2-xMoxO7, CaZr1-2xGd2xTi2-xMoxO7, CaZr1-2xHo2xTi2-xMoxO7 and CaZr1-2xYb2xTi2-xMoxO7 solid solutions are similar to each other: (1) zirconolite-2M in x=0.05 and 0.10; (2) co-existence of 2M and 4M and then formation of 4M phase from x=0.15 to 0.25; (3) formation of “yellow phase” and pyrochlore when x≥0.30. Interestingly, perovskite exits in all the ceramic samples, and its lattice parameters slightly change when increasing the dopants. Rietveld refinement results reveal that Sm/Ho mainly incorporates into 8f (Wyckoff position) Zr-sites while Mo replaces the 8f (Wyckoff position) Ti-sites. XANES results further confirm the occupation of Mo in TiO5 coordination environments. Furthermore, there is a considerable amount of Sm/Ho incorporated into 8f Ca-sites, demonstrating a different substitution mechanism from the preliminary design.

Performance of pulsed plasma thruster at low discharge energy

As the size of satellites scales down, low-power and compact propulsion systems such as the pulsed plasma thruster (PPT) are needed for stabilizing these miniature satellites in orbit. Most PPT systems are operated at 2 J or more of discharge energy. In this work, the performance of a PPT with a side-fed, tongue-flared electrode configuration operated within a lower discharge energy range of 0.5‒2.5 J has been investigated. Ablation and charring of the polytetrafluoroethylene propellant surface were analyzed through field-effect scanning electron microscopy imaging and energy-dispersive X-ray spectroscopy. When the discharge energy fell below 2 J, inconsistencies occurred in the specific impulse and the thrust efficiency due to the measurement of the low mass bit. At energy 2 J, the performance parameters are compared with other PPT systems of similar configuration and discussed in depth.

Effects of ethylenediaminetetraacetic acid, citric acid, and etidronic acid on root dentin mineral content and bond strength of a bioceramic-based sealer: A scanning electron microscopy-energy dispersive spectroscopy study

<strong data-sider-select-id="1257eba3-eefa-4e8c-96e6-f0f31f2d1932">Background. This study assessed the impact of chelating agents, 17% ethylenediaminetetraacetic acid (EDTA), 10% citric acid (CA), and 18% etidronic acid (HEDP), on root dentin mineral content. Scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) was applied to analyze changes, and the push-out bond strength test was used to measure dentin adhesion of Well-Root ST, a bioceramic root canal sealer. <strong data-sider-select-id="85a7b117-9f07-4687-bf87-608e92d5c2a7">Methods. A total of 80 extracted single-rooted lower premolar teeth were included in this study and randomly divided into four groups (n=20): group 1 (17% EDTA), group 2 (10% CA), group 3 (18% HEDP), and group 4 (distilled water, control). After irrigation and drying, SEM-EDS was applied to analyze eight samples from each group at coronal, middle, and apical root regions for mineral content and SEM images. The remaining 12 samples underwent a push-out bond strength test using Well-Root ST sealer and gutta-percha. Kruskal-Wallis and Dunn’s tests were used for statistical analyses. <strong data-sider-select-id="38615864-5e07-45cb-afc3-76a3e40032ee">Results. Statistically significant differences were found between groups (<em data-sider-select-id="99a01d49-b02c-4857-9312-f2d6463e687e">P<0.05). SEM-EDS showed significant differences in C, O, Ca, P, and Ca/P content, with no significant differences in Na and Mg. Push-out bond strength was significantly higher in the 17% EDTA, 10% CA, and 18% HEDP groups compared to the control group, with no significant differences between chelating agents. <strong data-sider-select-id="ff8577d5-0e96-425d-96b9-6d7885e00899">Conclusion. Chelating agents altered root dentin mineral content and improved the adhesive properties of the bioceramic sealer. These findings highlight the importance of considering the selection and use of chelating agents in the clinical practice for root canal treatment.

Study on the effectiveness of sulfate-reducing bacteria to remove Pb(II) and Zn(II) in tailings and acid mine drainage.

In view of water and soil getting polluted by Pb(II), Zn(II), and other heavy metals in tailings and acid mine drainage (AMD), we explored the removal effect of sulfate-reducing bacteria (SRB) on Pb(II), Zn(II), and other pollutants in solution and tailings based on the microbial treatment technology. We used the scanning electron microscope-energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), and X-ray fluorescence (XRF), to reveal the mechanism of SRB treatment of tailings. The results showed that SRB had a strong removal capacity for Zn(II) at 0-40 mg/L; however, Zn(II) at 60-100 mg/L inhibited the growth of SRB. Similarly, SRB exhibited a very strong ability to remove Pb(II) from the solution. At a Pb(II) concentration of 10-50 mg/L, its removal percentage by SRB was 100%. SRB treatment could effectively immobilize the pollutants leached from the tailings. With an increase in the amount of tailings added to each layer, the ability of SRB to treat the pollutants diminished. When 1 cm of tailingssand was added to each layer, SRB had the best effect on tailing sand treatment. After treatment, the immobilization rates of , Fe(III), Mn(II), Pb(II), Zn(II), Cu(II), and total Cr in the leachate of #1 tailing sand were 95.44%, 100%, 90.88%, 100%, 96.20%, 86.23%, and 93.34%, respectively. After the tailings were treated by SRB, although the tailings solidified into a cohesive mass from loose granular particles, their mechanical strength was <0.2 MPa. Desulfovibrio and Desulfohalotomaculum played the predominant roles in treating tailings by mixing SRB. The S2- and carbonate produced by mixing SRB during the treatment of tailings could metabolize sulfate by combining with the heavy metal ions released by the tailings to form FeS, MnS, ZnS, CuS, PbS, Cr2S3, CaCO3, MnCO3, and other precipitated particles. These particles were attached to the surface of the tailings, reducing the environmental pollution of the tailings in the water and soil around the mining area.