Scanning Electron Microscopy Backscatter Research Articles

Sputtering of silver nanoparticles bombarded with 3–100 keV Ar ions

Rutherford backscattering spectrometry and scanning electron microscopy were applied to obtain sputtering yields of Ag nanoparticles (5–30 nm in diameter) under 3–100 keV Ar+ ion irradiation. For low-energy ion irradiation, the diameter dependence of the sputtering yield was approximately 1.5 times higher than that of the bulk at diameters of a few nanometers, and then approached the bulk value at larger diameters. Under high-energy ion irradiation, especially for 100 keV Ar+ irradiation, the sputtering yields of Ag nanoparticles with diameters as small as a few nanometers were extremely higher than those predicted by the theoretical calculations. We concluded that such high sputtering yield originated in Ag cluster emission.

Adaptation of a heat-treatment condition to a precipitation-hardened nickel-based superalloy produced by laser powder bed fusion

This study evaluated the microstructural evolution and mechanical properties of a novel printable nickel-based superalloy subjected to a solution aging treatment. The microstructures of the alloys in as-fabricated and solution-treated states were characterized using a combination of electron backscatter diffraction analysis and scanning electron microscopy. The findings indicate that the cellular crystals gradually transitioned into equiaxed grains with increasing solution temperature. The grain orientation shifts from the <001> orientation perpendicular to the building direction to a random orientation. The average grain size increased, the proportion of low-angle grain boundaries (LAGBs) decreased, and the percentage of annealing twin boundaries (TBs) increased from 0.18% in the as-fabricated state to 65.68% at 1230 °C solution treatment (ST). After lower-temperature ST, a large amount of primary γ′ and η phases precipitated in the as-fabricated alloy, with spherical and needle-like shapes, respectively. As the solution temperature increased, the quantity of the primary γ′ phase gradually decreased, and the η phase became relatively more elongated. At 1130 °C ST, both phases dissolved; following aging treatment, γ′ phase precipitated fully. High strength (1493 MPa) was achieved after direct aging treatment, attributed to the combination of cellular structures and numerous LAGBs produced during deposition with the complete precipitation of γ′ phase during aging. This study demonstrated that laser powder bed fusion alloys can achieve excellent mechanical performance through direct aging without needing ST.

In-situ investigation on the carbonation behaviors of various mineral phases in steel slag: The role of RO phase

Exploring the mineral compositions of steel slag and the microstructure evolutions of its carbonation products is very important for deeply understanding the carbonation mechanism of steel slag, which can promote the application of steel slag in carbon capture and storage. In this paper, the carbonation behaviors of various mineral phases in steel slag were investigated by using an ingenious in-situ observation method through combing laser scanning confocal microscopy (LSCM), backscattered scanning electron microscopy (BSEM) and focused ion beam-transmission electron microscope (FIB-TEM). It is shown that dicalcium silicate (C2S) and free lime (f-CaO) had high carbonation reactivity, while the calcium aluminoferrite with different Al/Fe ratios and mayenite (C12A7) exhibited extremely poor carbonation reactivity. The carbonation reactivity of RO phase was positively correlated with its Mg/(Fe + Mn) ratio. RO phase with a Mg/(Fe + Mn) ratio below 0.5 owned almost no carbonation reactivity, while the Mg2+ would leach from RO phase with a Mg/(Fe + Mn) ratio higher than 2.0 during the carbonation process, inhibiting the precipitation of CaCO3, changing the micro morphology of CaCO3, and generating spheroidal aragonite. The ingenious in-situ observation method developed in this study provides a very visual information, which can be further extended to more fundamental research.

Experimental study and crystal plasticity modeling of additive manufacturing IN718 superalloy considering negative strain rate sensitivity behavior

Revealing underlying mechanisms of IN718 superalloy's negative strain rate sensitivity behavior at elevated temperatures is significantly important for its further applications in extreme conditions. This work investigates the microstructural mechanisms of the temperature-dependent strain rate sensitivity using experimental methods and crystal plasticity characterization model. Firstly, Electron backscatter diffraction (EBSD) and scanning electron microscopy (SEM) techniques are utilized to observe microstructural characteristics of additively manufactured IN718 alloy at different temperatures. The influence of solute precipitation and dislocation slip interaction on the mechanical properties is discussed. Subsequently, the representative volume element (RVE) model is constructed by using acquired orientation, grain size, and dislocation density data. Finally, the crystal plasticity model incorporating dynamic strain aging and dislocation density evolution is developed to characterize the relationship between strain rate sensitivity and temperature. The model can effectively simulate the transition of strain rate sensitivity of additive manufacturing materials. The results indicate that the increase in dislocation pinning caused by intensified carbon element precipitation at high temperatures is the primary reason of the strain rate sensitivity change observed in IN718 metal materials. The carbon precipitated at the dislocation nucleus induces serration flow in IN718 superalloy under high strain. This study contributes to understanding and characterizing the microscopic mechanisms of deformation in metal materials subjected to thermal environments.

Multi-scale characterization of fatigue crack tip deformation and propagation in QP steel

A novel measurement method for multi-scale characterization of fatigue crack tip deformation and propagation behaviors in high strength and plasticity, multi-phase, fine-grain Quenching and Partitioning (QP) steel was proposed. The fatigue crack propagation (FCP) test system with the macro/micro images acquisition devices was built to measure the FCP rate and crack tip deformation simultaneously. First, at the mesoscale, the evolution characteristics of the crack tip deformation fields, plasticity induced crack closure (PICC) behaviors and plastic zone during the FCP process were analyzed using the sub-image stitching and matching digital image correlation (DIC) method. Then, the FCP models were established with special emphasis on the model considering the PICC effect based on the obtained crack opening load at the mesoscale. Moreover, the corresponding microscale surface crack and fracture morphologies, microstructure phase transformation and deformations were observed and analyzed by electron backscatter diffraction (EBSD) and scanning electron microscope (SEM) techniques.

Improved concrete ITZ and performance via pre-soaking of inert recycled red brick aggregates in carbonation solution

Compared to recycled concrete aggregate (RCA), the high-water absorption of recycled red brick aggregate (RBA) has limited its utilization in concrete production. However, this study takes the advantage of its high-water absorption capacity as a carrier for carbonation solutions, aiming to compensate the strength loss by enhancing the interfacial transition zone (ITZ) properties of incorporated concrete. The effects of carbonation solutions (e.g., CO2 and NaHCO3) by varying the CO2 injection times (10 s, 60 s and 600 s) and NaHCO3 dosages (1%, 3% and 5%) on the physical (i.e. density and water absorption) and mechanical (i.e. compressive and tensile bond strengths) properties of concrete, in particular focus on the ITZ changes, were systematically investigated. In addition, the microstructure changes of concrete ITZ were studied using thermogravimetric analysis (TGA), scanning electron microscope-backscattered electron (SEM-BSE) image analysis and mercury intrusion porosimetry (MIP). The results indicated that it was feasible to enhance the ITZ properties by using CO2 solution as the pre-soaking agent of RBA. The adoption of CO2 solution could significantly improve the bond strength of ITZ by up to 22.5% and resulted 8.6% improvement in 28-day compressive strength. The CO2 solution contributed to the formation of CaCO3 can accelerate the cement hydration of surrounding matrix and hence densified the microstructure of ITZ. For the case of pre-soaking with NaHCO3, although the release of solution from RBA could improve the early strength of concrete, the later strength significantly reduced due to the effect of sodium ions in NaHCO3 on the growth of outer C–S–H gel.

Revealing the mechanism of ductility discrepancy between two 2205 duplex stainless steels containing layered and island austenite through in-situ experiment

A notable discrepancy in tensile ductility was observed between two 2205 duplex stainless steels (DSS) containing layered and island-like austenite microstructures. The deformation behavior of both DSS 2205 was compared through in-situ Electron Backscatter Diffraction (EBSD) and Scanning Electron Microscope (SEM) techniques. The results indicated that the microscopic deformation mechanism for both DSS 2205 was governed by dislocation slip. The observed tensile ductility disparity was attributed to differences in dislocation slip behavior. In DSS 2205 with island austenite, slip transfer and blocking across grain boundaries occurred simultaneously, which was determined by the geometrical compatibility factor (m') calculations of adjacent ferrite and austenite grains. This intensified plastic inhomogeneities and promoted non-Schmid dislocation slip behavior. While in layered austenite of DSS 2205, the activation of slip system strictly adhered to the principle of maximizing the Schmid factor. Multiple slip systems in the ferrite on {110} and {112} planes were activated, inducing cross-slip, which enhanced ductility. The better ductility of DSS 2205 featuring layered austenite compared to the counterpart was further explained by quantitative analysis of geometrically necessary dislocations (GND) distribution in both phases and kernel average misorientation (KAM) values during deformation.

Clarifying the contribution of multiscale pores to physical properties of Chang 7 tight sandstones: insight from full-scale pore structure and fractal characteristics

The pore structure and its heterogeneity of tight reservoirs are key factors affecting the storage and percolation of crude oil. The pore system of Chang 7 tight sandstone has multi-scale and multi-type characteristics. However, the contribution of different pore types and pore sizes to the physical properties of Chang 7 tight sandstone is still unclear. In this paper, we collected a suite of Chang 7 tight sandstones to investigate the full-scale pore structure and fractal characteristics by casting thin section, field emission scanning electron microscope, two-dimensional multi-scale backscattered scanning electron microscopy, N2 adsorption (NA) and NMR. The pore diameters of Chang 7 tight sandstone are usually distributed between 0.001 and 20 μm. Intercrystalline pores are mainly distuibuted &amp;lt;500 nm. Dissolution pores vary from 100 nm to 100 μm. Residual intergranular pores range from 1 μm to 40 μm. Based on the fractal characteristics, pore system is divided into macropores (mainly &amp;gt;300 nm), mesopores (mainly 7–300 nm), and micropores (mainly &amp;lt;7 nm). Micropores are adsorb-fluid pores that do not contribute to the storage and percolation but contribute significantly to contrasting specific surface area. Mesopores represent bound-fluid pores and only contribute to total porosity but not to permeability. Macropores represent movable-fluid pores, contributing to both porosity and permeability. The content and heterogeneity of macropores control the quality of Chang 7 tight sandstone. When macropore volume is &amp;gt;12×10−3 mL/g, the continuous percolation network consists entirely of macropores, resulting in higher porosity and permeability of the reservoir. Moreover, reservoir physical properties show excellent correlation with macropore heterogeneity. These results demonstrate that the content and heterogeneity of macropores are key indicators indicating the quality of the Chang 7 tight sandstones.

Behaviour of alkali-activated fly ash-slag paste at elevated temperatures: An experimental study

As an environmentally friendly material, alkali-activated fly ash-slag (AAFS) is considered as a promising alternative cement because of its excellent mechanical properties and thermal stability. Nevertheless, high temperature induced damage in AAFS can potentially bring serious risks for its practical applications. This paper presents a systematic experimental study on behaviour of AAFS paste subjected to elevated temperatures up to 800 °C in terms of microstructure as well as thermal and mechanical properties. Microstructural evolution was characterised by means of Rietveld-based quantitative X-ray diffraction (QXRD), backscattered scanning electron microscope (BSEM) and X-ray microcomputed tomography (XCT), while thermal and mechanical properties were evaluated from thermogravimetric analysis (TGA), thermal deformation and compressive and flexural strengths. Results indicate that the compressive strength of AAFS paste rises by 77.5 % at 200 °C, followed by a mitigation from 200 to 600 °C and a regain at 800 °C. Different phases in AAFS paste including unreacted particles, reaction products and pores took up 30 %, 67.7 % and 2.31 % at ambient temperature, and 4.95 %, 84.8 % and 10.3 % after exposure to 800 °C, respectively, suggesting the recrystallisation with the formation of nepheline and gehlenite. In addition, the relationships between microstructural characteristics including three-dimensional (3D) pore structure features and thermal and mechanical properties of AAFS paste at elevated temperatures were explored and discussed in depth to gain insights into the underlying degradation mechanisms including pore pressure build-up, thermal gradient and phase transformation.

Reducing the prosthesis modulus by inclusion of an open space lattice improves osteogenic response in a sheep model of extraarticular defect.

Introduction: Stress shielding is a common complication following endoprosthetic reconstruction surgery. The resulting periprosthetic osteopenia often manifests as catastrophic fractures and can significantly limit future treatment options. It has been long known that bone plates with lower elastic moduli are key to reducing the risk of stress shielding in orthopedics. Inclusion of open space lattices in metal endoprostheses is believed to reduce the prosthesis modulus potentially improving stress shielding. However, no in vivo data is currently available to support this assumption in long bone reconstruction. This manuscript aims to address this hypothesis using a sheep model of extraarticular bone defect. Methods: Initially, CT was used to create a virtual resection plan of the distal femoral metaphyses and to custom design endoprostheses specific to each femur. The endoprostheses comprised additively manufactured Ti6Al4V-ELI modules that either had a solid core with a modulus of ∼120GPa (solid implant group) or an open space lattice core with unit cells that had a modulus of 3-6GPa (lattice implant group). Osteotomies were performed using computer-assisted navigation followed by implantations. The periprosthetic, interfacial and interstitial regions of interest were evaluated by a combination of micro-CT, back-scattered scanning electron microscopy (BSEM), as well as epifluorescence and brightfield microscopy. Results: In the periprosthetic region, mean pixel intensity (a proxy for tissue mineral density in BSEM) in the caudal cortex was found to be higher in the lattice implant group. This was complemented by BSEM derived porosity being lower in the lattice implant group in both caudal and cranial cortices. In the interfacial and interstitial regions, most pronounced differences were observed in the axial interfacial perimeter where the solid implant group had greater bone coverage. In contrast, the lattice group had a greater coverage in the cranial interfacial region. Conclusion: Our findings suggest that reducing the prosthesis modulus by inclusion of an open-space lattice in its design has a positive effect on bone material and morphological parameters particularly within the periprosthetic regions. Improved mechanics appears to also have a measurable effect on the interfacial osteogenic response and osteointegration.

Segmentability evaluation of back-scattered SEM images of multiphase materials

Segmentation methods are very useful tools in the Electron Microscopy inspection of materials, enabling the extraction of quantitative results from microscopy images. Back-Scattered Electron (BSE) images carry information of the mean atomic number in the interaction volume and hence can be used to quantify the phase composition in multiphase materials. Since phase composition and proportion affects the material properties and hence its applications, the segmentation accuracy of such images rendered of critical importance for material science. In this work, the notion of segmentability for BSE images is proposed to define the ability of an image to be segmented accurately. This notion can be used to guide the image acquisition process so that segmentability is maximized and segmentation accuracy is ensured. An index is devised to quantify segmentability based on a combination of the modified Fisher Discrimination Ratio and of the second Minkowski functional capturing intensity and spatial aspects of BSE images respectively. The suggested Segmentability Index (SI) is validated in synthetic BSE images which are generated with a novel algorithm allowing the independent control of spatial distribution of phases and their grayscale intensity histograms. Additionally, SI is applied in real-synthetic BSE images, where the real greyscale distributions of Ordinary Portland Cement (OPC) clinker crystallographic phases are used, to demonstrate the ability of SI to indicate the optimum choice of critical image acquisition settings leading to the more accurate segmentation output.

In-situ study on the coordinated deformation mechanism of austenitic stainless steel with mixed crystal degree

A novel in-situ tensile experiment is designed to investigate the coordinated deformation mechanism between coarse grains (CGs) and fine grains (FGs) in the mixed crystal structure of X2CrNiMo18.12 austenitic stainless steel (X18.12). In-situ electron backscatter diffraction (EBSD) and scanning electron microscopy (SEM) techniques are employed. The experiment involves quantitatively calculating the initial order and number of slip systems, rotation rate, and rotation path of FGs in two groups of mixed crystal structures with different degrees of mixing. The results reveal that the slip trace is predominantly generated in the CGs which have harder crystal orientation at a small deformation of 1.4 %. It is observed that the activation of slip traces in FGs becomes increasingly challenging as the degree of mixed crystal increases. The crystallographic orientation of the grains exhibited a certain degree of rotation to facilitate slip activation. Analysis of grain rotation demonstrates that most grains rotated along the [111] direction during the in-situ tensile test. Additionally, grains with a grain size below 100 μm typically follow a single rotation path but exhibit a high rotation rate. Comparing the mixed grain structures with mixed crystal degrees of 7 and 3, it is observed that the former exhibited a higher grain rotation rate, further indicating the increased difficulty in achieving coordinated deformation in structures with a higher degree of mixed crystal. These findings provide valuable insights into the synergistic deformation behavior of CGs and FGs in mixed crystal structures.

Isoplethal study of phase formation and morphology in uranium-304L steel via scanning electron microscopy

ABSTRACT Understanding the formation of uranium alloys with steel is important to advance nuclear technologies involving U metal fuels and machining U metal, and for nuclear forensics applications. No known phase diagram for the quaternary U-(M = Fe, Ni, Cr) system exists. We synthesize samples of U-304 L steel (nominal composition 70.1:18.3:10.4 at% Fe:Cr:Ni) across the U composition range 4.45—63.35 at%U by arc melting under inert conditions. Using the binary UFe phase diagram as a reference, we identify four U-steel alloy phases. We find the known U-Fe analogue phases UM2 and U6M, and two low-U composition phases with nominal compositions UM10 and U2M7. We apply a correlation length analysis to backscatter scanning electron microscopy images of sectioned and polished cross sections to quantify the domain formation length scale. We demonstrate that these depend heavily on the initial composition and range from 30 nm to 1.5 µm. This result, in particular, could be applicable to theoretical predictions of transport properties. Furthering our understanding of U alloy phase formation with important structural elements such as steel primaries is foundational in developing future nuclear technology. 1

Magnetite geochemistry and mineralogy of iron skarn in the southern Wag Water Belt, Jamaica: Implications for ore genesis

The Mavis Bank iron skarn mineralisation is located within a Paleocene to Eocene rift system typified by terrestrial and marine deposits, and extensive lava flows and subvolcanic intrusions of adakitic composition. Iron occurs primarily as massive, lenticular magnetite bodies at the contact between the intrusions and calcic Fe skarn (metasomatised limestone) which grades into a low-grade marble with disseminated magnetite. Magnetite is also disseminated in shales and lavas located within the main mineralised zones. Skarn mineralogy is poorly developed in both the endoskarn and the exoskarn with only minor occurrence of diopside. Retrograde and alteration minerals, such as epidote, chlorite, and hematite, are more common. Sulphides are rare, highly altered, and dominated by pyrite, pyrrhotite, and minor chalcopyrite. Petrographic analysis, including micro-XRF-EDS mapping of polished thin sections, shows that massive magnetite and calcic Fe skarns have minor disseminated Ti and S phases along with trace amounts of Cu and Co. Scanning electron microscope-backscattered electron (SEM-BSE) imaging of the exoskarn highlights the extent of retrograde alteration and later supergene weathering, and the presence of dissolution and reprecipitation features.The in situ trace element composition of magnetite in massive magnetite and calcic Fe skarn was determined using LA-ICP-MS. The results, when plotted on multi-element and discriminant diagrams, including Ni/(Cr + Mn) vs Ti + V, Ca + Al + Mn vs Ti + V, Ti vs V, and Ti vs Ni/Cr, are generally consistent with the geochemical signatures of skarn deposits worldwide. The mineralogy and trace element signatures suggest that the skarn deposit was formed at relatively shallow levels by low temperature hydrothermal fluids with high fO2 and fS. In addition, δ18O values of 6.6 and 7.1 ‰ obtained from massive magnetite are typical of infiltrative skarns and are consistent with a mixture of magmatic and meteoric water, and limestone oxygen isotope signatures.

Embedding and Backscattered Scanning Electron Microscopy (EM-BSEM) Is Preferential over Immunophenotyping in Relation to Bioprosthetic Heart Valves.

Hitherto, calcified aortic valves (AVs) and failing bioprosthetic heart valves (BHVs) have been investigated by similar approaches, mostly limited to various immunostaining techniques. Having employed multiple immunostaining combinations, we demonstrated that AVs retain a well-defined cellular hierarchy even at severe stenosis, whilst BHVs were notable for the stochastic degradation of the extracellular matrix (ECM) and aggressive infiltration by ECM-digesting macrophages. Leukocytes (CD45+) comprised ≤10% cells in the AVs but were the predominant cell lineage in BHVs (≥80% cells). Albeit cells with uncertain immunophenotype were rarely encountered in the AVs (≤5% cells), they were commonly found in BHVs (≥80% cells). Whilst cell conversions in the AVs were limited to the endothelial-to-mesenchymal transition (represented by CD31+α-SMA+ cells) and the formation of endothelial-like (CD31+CD68+) cells at the AV surface, BHVs harboured numerous macrophages with a transitional phenotype, mostly CD45+CD31+, CD45+α-SMA+, and CD68+α-SMA+. In contrast to immunostaining, which was unable to predict cell function in the BHVs, our whole-specimen, nondestructive electron microscopy approach (EM-BSEM) was able to distinguish between quiescent and matrix-degrading macrophages, foam cells, and multinucleated giant cells to conduct the ultrastructural analysis of organelles and the ECM, and to preserve tissue integrity. Hence, we suggest EM-BSEM as a technique of choice for studying the cellular landscape of BHVs.

Additive Manufacturing Benchmark 2022 Subcontinuum Mesoscale Tensile Challenge (CHAL-AMB2022-04-MeTT) and Summary of Predictions.

This additive manufacturing benchmarking challenge asked the modelling community to predict the stress-strain behavior and fracture location and pathway of an individual meso-scale (gauge dimensions of approximately 200 μm thickness, 200 μm width, 1mm length) tension specimen that was excised from a wafer of nickel allow IN625 manufactured by laser powder bed fusion (L-PBF). The data used for the challenge questions and answers are provided in a public dataset (https://data.nist.gov/od/id/mds2-2587). Testing models against the data is still possible, although a good-faith blinded prediction should be attempted before reading this article, as the results are contained herein. The uniaxial tension test was pin loaded, conducted at quasi-static strain rates under displacement control, and strain was measured via non-contact methods (digital image correlation). The predictions are challenging since the number of grains contained in the thickness of the specimen are sub-continuum. In addition, pores can be heterogeneously distributed by the L-PBF process, as opposed to intentionally seeded defects. The challenge provided information on chemical composition, grain and subgrain structure (surface-based measurements via electron backscatter diffraction and scanning electron microscopy) and pore structure (volume-based measurements via X-Ray computed tomography) along the entire gauge length for the tension specimen. During the challenge, prediction responses were collected from six different groups. Prediction accuracy compared to the measurements varied, with elastic modulus and strain at ultimate tensile strength consistently over-predicted, while most other values were a mix of over- and under-predicted. Overall, no one model performed best at all predictions. Failure-related properties proved quite challenging to predict, likely in part due to the data provided as well as the inherent difficulty in predicting fracture. Future directions and areas of improvement are discussed in the context of improving model maturity and measurement uncertainty.

Fatigue crack growth behavior of SS316L deposition from wire arc additive manufacturing

Wire arc additive manufacturing has shown the potential to build large metal parts with high deposition rates and low cost of production compared to other additive manufacturing techniques. Austenitic stainless steel 316L is known for corrosion resistance and weldability, which makes it a strong candidate for building and repairing marine and offshore parts, with wire arc additive manufacturing. These parts experience fluctuating loads during service, which necessitates the fatigue performance study of wire arc additively build stainless steel. This work investigates the fatigue crack propagation behavior of stainless steel 316L depositions from wire arc additive manufacturing. Single beads of stainless steel 316L were deposited layer by layer to fabricate the wall structures. From the wall structures, the specimens were prepared for the tensile and fatigue crack growth rate tests along the traverse and build directions. In conjunction with mechanical testing, electron back-scattered diffraction and scanning electron microscopy techniques were employed to characterize the microstructure. Microstructural observations showed the presence of columnar dendrites along the build direction. The electron dispersive spectroscopy revealed the elemental diffusion at the layer interfaces due to the remelting of the layers. Differences in mechanical properties were observed across the two directions. Along build directions, the ultimate tensile strength was 8 % higher and yield strength was 7 % lower than the respective strengths along the traverse direction. The build direction also exhibited 46 % higher fatigue life cycle than the traverse direction. The difference in properties across different orientations was closely associated with the microstructural variations. Overall, the mechanical performance of the wire arc additively deposited SS316L is better than the previously reported selective laser melted SS316L.

Large-field-of-view scanning electron microscopy of the paraventricular nucleus of the hypothalamus during diet-induced obesity.

Dysregulation in the paraventricular nucleus of the hypothalamus (PVN) is associated with a variety of diseases including those related to obesity. Although most investigations have focused on molecular changes, structural alterations in PVN neurons can reveal underlying functional disruptions. Although electron microscopy (EM) can provide nanometer resolution of brain structures, an inherent limitation of traditional transmission EM is the single field of view nature of data collection. To overcome this, we used large-field-of-view high-resolution backscatter scanning electron microscopy (bSEM) of the PVN. By stitching high-resolution bSEM images, taken from normal chow and high-fat diet mice, we achieved interactive, zoomable maps that allow for low-magnification screening of the entire PVN and high-resolution analyses of ultrastructure at the level of the smallest cellular organelle. Using this approach, quantitative analysis across the PVN revealed marked electron-dense regions within neuronal nucleoplasm following high-fat diet feeding, with an increase in kurtosis, indicative of a shift away from a normal distribution. Furthermore, measures of skewness indicated a shift toward darker clustered electron-dense regions, potentially indicative of heterochromatin clusters. We further demonstrate the utility to map out healthy and altered neurons throughout the PVN and the ability to remotely perform bSEM imaging in situations that require social distancing, such as the COVID-19 pandemic. Collectively, these findings present an approach that allows for the precise placement of PVN cells within an overall structural and functional map of the PVN. Moreover, they suggest that obesity may disrupt PVN neuronal chromatin structure.NEW & NOTEWORTHY Paraventricular nucleus of the hypothalamus (PVN) alterations are linked to obesity-related conditions, but limited knowledge exists about neuroanatomical changes in this region. A large-field-of-view backscatter scanning electron microscopy (bSEM) method was used, which allowed the identification of up to 40 PVN neurons in individual samples. During obesity in mice, bSEM revealed changes in PVN neuronal nucleoplasm, possibly indicating chromatin clustering. This microscopy advancement offers valuable insights into neuroanatomy in both healthy and disease conditions.

Production of Ultrahigh‐Strength and High‐Ductility TWIP Steel by Precipitation of β‐Mn during Large Deformation during Warm‐Rolling

Herein, twinning‐induced plasticity (TWIP) steel having large deformation is rolled at different rolling temperatures to improve the tensile strength and retain a certain plastic deformation capacity. Based on X‐ray diffraction and transmission electron microscope analysis, β‐Mn is found as the precipitate at the grain boundary during the warm‐rolling process (500–650 °C). To investigate the impact of β‐Mn on the tensile properties, the microstructure of the TWIP steel rolled at the temperature value of 600 °C is observed by carrying out electron backscatter diffraction and scanning electron microscope measurements. The intergranular β‐Mn phase can help the material to accumulate geometric necessary dislocation (GND) density, inhibit crack propagation, as well as improve the strength and plasticity of the material. Once TWIP steel is warm‐rolled above the temperature value of 600 °C, and serrated flow appears in the tensile process, which is also conducive to improving the material properties.

Mechanism underlying effect of expansive agent and shrinkage reducing admixture on mechanical properties and fiber-matrix bonding of fiber-reinforced mortar

Expansive agent (EA) and shrinkage reducing admixture (SRA) are utilized to reduce shrinkage and risk of cracking in concrete. EA compensates shrinkage by initial expansion, and SRA reduces surface tension in the pore fluid. Although EA and SRA effectively reduce shrinkage, they can impair micro-structure of concrete at high contents. The shrinkage reduction effect of EA and SRA is well known; however, there is limited knowledge about their negative effect on microstructure and fiber matrix interfacial transition zone (ITZ). The current study explores the effect of using 10 % CaO-based EA, 2 % SRA, and their combination on mechanical, shrinkage, and microstructural properties of fiber-reinforced mortar (FRM) made with 0.5 % steel fiber. The hydration products are characterized by X-ray diffraction and derivative thermogravimetric. Backscatter scanning electron microscopy, energy dispersive spectroscopy (EDS), and micro-hardness experiments are employed to characterize the microstructure of fiber-matrix ITZ at two distances of 50 and 100 μm surrounding the fibers. Experiment results indicate that the quality of ITZ and fiber-matrix bonding is impaired by using either EA or SRA. The highest drop is obtained by the combination of EA and SRA. The element analysis by EDS line and point scanning reveals the presence of longer silicate chain and stronger fiber-matrix ITZ in the reference mixture. Micro-hardness measurements confirm higher mechanical properties at the ITZ between 50 and 100 μm surrounding the fibers. Thermodynamic simulations and phase assemblages interpret the influence of EA and SRA on mechanical properties and shrinkage.