Satellite Soil Moisture Products Research Articles

Temperature Effects in AMSR2 Soil Moisture Products and Development of a Removal Method Using Data at Ascending and Descending Overpasses

Soil moisture is among the most essential variables in hydrology and earth science. Many satellite missions, such as AMSR-E/2, have been launched to observe it in broader spatial coverage to overcome the shortage of in situ observations. However, the satellite soil moisture products have been reported to comprise errors caused by the so-called “temperature effects” widely observed in dielectrically measured in situ volumetric soil water content (SWC). In this work, we confirmed the existence of these errors in AMSR2 soil moisture products. A new algorithm was developed to remove these errors using satellite data at ascending and descending overpasses. The application of this algorithm to both satellite and in situ data of SWC and soil temperature at the Mongolia site shows that the difference between SWC values at ascending and descending overpasses caused by temperature effects is effectively removed. We assess the impact of this removal method on satellite data by comparing it with in situ data, utilizing metrics such as the correlation coefficient and other widely adopted evaluation methods. It is shown that the difference between the original and corrected in situ SWC is much smaller than that between AMSR2 and in situ SWC, either corrected or not. The results indicate that the metric values between the corrected AMSR2 and in situ SWC, after removing apparent differences caused by temperature effects, slightly improved compared to those between the original AMSR2 and in situ SWC. Though these findings imply that the removed errors may not be the most dominant, considering the current significant difference between AMSR2 and in situ SWC, the removal makes the ascending and descending data have close characteristics. It may allow using data at both ascending and descending overpasses and double the temporal resolution of AMSR2 SWC data.

Validation of Satellite Soil Moisture Products by Sparsification of Ground Observations

Validation of Satellite Soil Moisture Products by Sparsification of Ground Observations

Estimating multi-scale irrigation amounts using multi-resolution soil moisture data: A data-driven approach using PrISM

Irrigated agriculture is the primary driver of freshwater use and is continuously expanding. Precise knowledge of irrigation amounts is critical for optimizing water management, especially in semi-arid regions where water is a limited resource. This study proposed to adapt the PrISM (Precipitation inferred from Soil Moisture) methodology to detect and estimate irrigation events from soil moisture remotely sensed data. PrISM was originally conceived to correct precipitation products, assimilating Soil Moisture (SM) observations into an antecedent precipitation index (API) formula, using a particle filter scheme. This novel application of PrISM uses initial precipitation and SM observations to detect instances of water excess in the soil (not caused by precipitation) and estimates the amount of irrigation, along with its uncertainty. This newly proposed approach does not require extensive calibration and is adaptable to different spatial and temporal scales. The objective of this study was to analyze the performance of PrISM for irrigation amount estimation and compare it with current state-of-the-art approaches. To develop and test this methodology, a synthetic study was conducted using SM observations with various noise levels to simulate uncertainties and different spatial and temporal resolutions. The results indicated that a high temporal resolution (less than 3 days) is crucial to avoid underestimating irrigation amounts due to missing events. However, including a constraint on the frequency of irrigation events, deduced from the system of irrigation used at the field level, could overcome the limitation of low temporal resolution and significantly reduce underestimation of irrigation amounts. Subsequently, the developed methodology was applied to actual satellite SM products at different spatial scales (1 km and 100 m) over the same area. Validation was performed using in situ data at the district level of Algerri-Balaguer in Catalunya, Spain, where in situ irrigation amounts were available for various years. The validation resulted in a total Pearson’s correlation coefficient (r) of 0.80 and a total root mean square error (rmse) of 7.19 mm∕week for the years from 2017 to 2021. Additional validation was conducted at the field level in the Segarra-Garrigues irrigation district using in situ data from a field where SM profiles and irrigation amounts were continuously monitored. This validation yielded a total bi-weekly r of 0.81 and a total rmse of −9.34 mm∕14-days for the years from 2017 to 2021. Overall, the results suggested that PrISM can effectively estimate irrigation from SM remote sensing data, and the methodology has the potential to be applied on a large scale without requiring extensive calibration or site-specific knowledge.

Intercomparison of recent microwave satellite soil moisture products on European ecoregions

Several satellite microwave-based soil moisture (SM) products have become available in recent years, making possible to produce different datasets at continental and/or a global scale. Numerous variables, including geographic heterogeneity, weather and climate, and land cover, have an impact on these products' accuracy. In this study, we account for all these variables by using the ecoregions as the scale of analysis and conducting a thorough comparison of satellite products with ground-based SM measurements. The whole Europe has been selected as study area, considering it as the aggregation of several ecoregions, each of them classified as an homogeneous zones, in terms of climate, vegetation and potentially investigable soil cover. Selected SM satellite data includes: i) the National Aeronautics and Space Administration (NASA) SMAP L4 V5; ii) the European Space Agency (ESA) SMOS-IC V2.0; iii) the H115 and H116 SM products in time-series format generated by analyzing data collected by the Advanced Scatterometer (ASCAT) aboard MetOp satellites; iv) the CGLS SSM 1 km obtained by the radar onboard ESA’s SENTINEL-1 platforms; and v) the European Space Agency’s Climate Change Initiative for Soil Moisture (ESA CCI SM) “COMBINED” ESA CCI SM v06.1 product, created by merging satellite-based passive/active microwave measurements. Such a variety, in terms of technologies and main features, of publicly available online SM products (in their up-to-date version), allowed for a comprehensive intercomparison against in situ measurements of the International Soil Moisture Network (ISMN), that spreads across all of Europe within the above-mentioned terrestrial ecoregion, using four different metrics, i.e., r, bias, ubRMSE and r/rANOM.Overall the intercomparison has underlined how SMAP L4 and ESA CCI show the best performance regardless of the considered metric. ASCAT has achieved best performances among non-modeled/blended products, while SMOS-IC has showed slightly better performance than the CGLS SSM 1 km. Using ecoregions allowed to further characterize the differences of each satellite products and identify the areas where all these products are more reliable (e.g., group (1) made by ecoregions as the Cantabrian Mixed forests or the Balkan Mixed forests; or group 2 made by ecoregions which belong to Mediterranean area) or less performing (e.g., the Central European mixed forests and the Pontic steppe). Hence, these classes have been further analyzed exploiting the ERA5-Land data, in terms of the SM, air temperature, precipitation, evaporation and Leaf area index. The research has provided helpful insights into how the performance of particular SM satellite products changes based on both the characteristics of the product under consideration and the area under investigation (i.e., one ecoregion compared to another).

Integration of microwave satellite soil moisture products in the contextual surface temperature-vegetation index models for spatially continuous evapotranspiration estimation

The contextual surface temperature-vegetation index (TVX) models have been widely used for the retrieval of soil moisture (SM) and evapotranspiration (ET). One of the key premises for their application is to determine quantitatively the theoretical boundaries of this contextual TVX space. Usually these theoretical boundaries are determined based on land surface energy balance principle. Although sound in physical mechanism, the complex parameterization involved has hampered its remote sensing (RS) applications. Our recent studies show that ground-based SM observations can be used for a quick and continuous retrieval of these theoretical boundaries. The main disadvantage lies in its reliance on in-situ SM observations. Fortunately the development of microwave RS technology has made it possible to monitor SM at both regional and global scale. Under this background, a practical framework based on the contextual TVX models was proposed in this paper for continuous ET estimation through the combination of microwave-based SM products and MODIS (Moderate Resolution Imaging Spectroradiometer) products. Daily actual ET over the Southern Great Plains of the United States of America was calculated as the product of net radiation and evaporative fraction (EF). The focus of this framework was to investigate how optical and microwave RS can be combined to achieve a quick and continuous retrieval of EF independently of ground observations. Specifically, EF was retrieved from the contextual TVX models, the theoretical boundaries of which were calibrated at the annual scale based on an optimization scheme. Assuming the seasonal variation of the theoretical dry edge follows a cosine function of solar zenith, the essence of this optimization scheme is to search for the optimal amplitude parameter that maximizes the correlation between microwave-based SM observations and soil moisture index retrieved from the contextual TVX models. Two microwave-based SM products including SMAP (Soil Moisture Active Passive) and SMOS (Soil Moisture and Ocean Salinity) were adopted to demonstrate this optimization scheme. The correlation coefficient, root mean square error and bias of EF estimates calibrated by SMAP were 0.700, 0.146 and 0.047, and those achieved by SMOS were 0.663, 0.174 and 0.168, respectively. The optimization scheme has not only made it possible to conduct a continuous monitoring of ET based entirely on RS observations but also achieved the downscaling of microwave satellite SM products. Thus the combination of optical and microwave RS holds great potential for coupled and continuous estimation of SM and ET over large scale.

Evaluation of SMAP-Enhanced Products Using Upscaled Soil Moisture Data Based on Random Forest Regression: A Case Study of the Qinghai–Tibet Plateau, China

The evaluation of satellite soil moisture is a big challenge owing to the large spatial mismatch between pixel-based satellite soil moisture products and point-based in situ measurements. Upscaling in situ measurements to obtain the “true value” of soil moisture content at the satellite grid/footprint scale can make up for the scale difference and improve the validation. Many existing upscaling methods have strict requirements regarding the spatial distribution and quantity of soil moisture sensors. However, in reality, soil-moisture-monitoring networks are commonly sparse with low sensor density, which increases the difficulty of obtaining accurate upscaled soil moisture data and limits the validation of satellite products. For this reason, this paper proposes a scheme to upscale in situ measurements using five machine learning methods along with Landsat 8 datasets and DEM data to validate the accuracy of a SMAP-enhanced passive soil moisture product for a sparse network on the Qinghai–Tibet Plateau. The proposed scheme realizes the upscaling of in situ soil moisture data to the pixel scale (30 m × 30 m) and then to the coarse grid scale (9 km × 9 km) by using multi-source remote sensing data as the bridge of scale conversion. The long-time SMAP SM products since April 2015 on the Qinghai–Tibet Plateau were validated based on upscaled soil moisture data. The results show that (1) random forest regression performs the best, and the upscaled soil moisture data reflect the region-average soil moisture conditions that can be used for evaluating SMAP data; (2) the SMAP product meets its scientific measurement requirements; and (3) the SMAP product generally underestimates the soil moisture in the study area.

A global analysis of water storage variations from remotely sensed soil moisture and daily satellite gravimetry

Abstract. Water storage changes in the soil can be observed on a global scale with different types of satellite remote sensing. While active or passive microwave sensors are limited to the upper few centimeters of the soil, satellite gravimetry can detect changes in the terrestrial water storage (TWS) in an integrative way, but it cannot distinguish between storage variations in different compartments or soil depths. Jointly analyzing both data types promises novel insights into the dynamics of subsurface water storage and of related hydrological processes. In this study, we investigate the global relationship of (1) several satellite soil moisture products and (2) non-standard daily TWS data from the Gravity Recovery and Climate Experiment/Follow-On (GRACE/GRACE-FO) satellite gravimetry missions on different timescales. The six soil moisture products analyzed in this study differ in the post-processing and the considered soil depth. Level 3 surface soil moisture data sets of the Soil Moisture Active Passive (SMAP) and Soil Moisture and Ocean Salinity (SMOS) missions are compared to post-processed Level 4 data products (surface and root zone soil moisture) and the European Space Agency Climate Change Initiative (ESA CCI) multi-satellite product. On a common global 1∘ grid, we decompose all TWS and soil moisture data into seasonal to sub-monthly signal components and compare their spatial patterns and temporal variability. We find larger correlations between TWS and soil moisture for soil moisture products with deeper integration depths (root zone vs. surface layer) and for Level 4 data products. Even for high-pass filtered sub-monthly variations, significant correlations of up to 0.6 can be found in regions with a large, high-frequency storage variability. A time shift analysis of TWS versus soil moisture data reveals the differences in water storage dynamics with integration depth.

Uncertainty Quantification of Satellite Soil Moisture Retrieved Precipitation in the Central Tibetan Plateau

SM2RAIN is a well-established methodology for estimating precipitation from satellite or observed soil moisture and it has been applied as a complementary approach to conventional precipitation monitoring methods. However, satellite soil moisture retrievals are usually subject to various biases and limited number of retrievals (and therefore large intervals) in remote areas, such as the Tibetan Plateau (TP), and little is known about their potential impacts on precipitation estimation. This study seeks to quantify the uncertainties in Soil Moisture Active and Passive (SMAP) soil moisture estimated precipitation through the commonly used SM2RAIN by referring to in situ soil moisture observations from the central Tibetan Plateau soil moisture network. The estimated precipitation is evaluated against rain gauge observations. Additional attention is paid to different orbits of the SMAP retrievals. Results show that the original SM2RAIN algorithm tends to underestimate the precipitation amount in the central TP when using SMAP soil moisture retrievals as input. The retrieval accuracy and sampling interval of SMAP soil moisture from ascending (descending) orbits each count for 1.04 mm/5 d (−0.18 mm/5 d) and 1.67 mm/5 d (0.72 mm/5 d) of estimated precipitation uncertainties as represented by root mean square error. Besides, the descending product of SMAP with a relatively less sampling interval and higher retrieval accuracy outperforms the ascending one in estimating precipitation, and the combination of both two orbits does add value to the overall SM2RAIN estimation. This study is expected to provide guidance for future applications of SM2RAIN-derived precipitation. Meanwhile, more reliable SM2RAIN precipitation estimations are desired when using higher quality satellite soil moisture products with better retrieval accuracy and smaller intervals.

Assessing and comparing the subseasonal variations of summer soil moisture of satellite products over eastern China

AbstractUsing the 43‐station soil moisture (SM) at a depth of 0–10 cm over eastern China, the near‐surface (about 0–5 cm) SM products from satellite missions including the level‐2 product of Chinese FengYun 3C (FY3C), level‐2 neural network product of the European Soil Moisture and Ocean Salinity (SMOS) and level‐4 product of the US Soil Moisture Active Passive (SMAP) were evaluated and compared during summers of 2015–2018. Thus, features of those products can be identified for their further application of climate study over eastern China. Large diversity is found among the satellite and field SM in terms of spatial distribution. This disagreement may cause the poor performance of the relationship between spatial coefficients of variation (CV) and mean SM. Compared with the field SM, the FY3C SM has smaller bias than the other satellite products. FY3C also performs better than SMOS in terms of the root‐mean‐square error (RMSE) and unbiased RMSE (ubRMSE) but has the smallest correlation coefficient (R). The SMAP product is generally the best among the three products in terms of RMSE, ubRMSE and R. However, a good performance in those metrics does not guarantee the same results on various time scales. On subseasonal time scales, the R in FY3C is the smallest among the three products, and the SMAP product has the largest R, but its amplitudes of the subseasonal variations are much smaller than the field observations. This indicates that when the SMAP products are applied for the analysis on subseasonal SM–atmosphere interactions, the effects of SM may be underestimated. On 10–30 days and above 60 days, dry period tends to have large spatial CV but this phenomenon is weak in all the satellite products. On the other hand, dry area tends to have large temporal CV on the four time scales, and this relationship is the strongest in SMAP but the weakest in FY3C. Therefore, there are large uncertainties of variability among different satellite SM products on subseasonal time scales over eastern China. Besides seasonal and overall performance, more attention is called to the variations on different time scales.

Is It Possible to Quantify Irrigation Water‐Use by Assimilating a High‐Resolution Satellite Soil Moisture Product?

AbstractIrrigation is the largest human intervention in the water cycle that can modulate climate extremes, yet irrigation water use (IWU) remains largely unknown in most regions. Microwave remote sensing offers a practical way to quantify IWU by monitoring changes in soil moisture caused by irrigation. However, high‐resolution satellite soil moisture data is typically infrequent (e.g., 6–12 days) and thus may miss irrigation events. This study evaluates the ability to quantify IWU by assimilating high‐resolution (1 km) SMAP‐Sentinel 1 remotely sensed soil moisture with a physically based land surface model (LSM) using a particle batch smoother (PBS). A suite of synthetic experiments is devised to evaluate different error sources. Results from the synthetic experiments show that unbiased simulations with known irrigation timing can produce an accurate irrigation estimate with a mean annual bias of 0.45% and a mean R2 of 0.97, relative to observed IWU. Unknown irrigation timing can significantly deteriorate the model performance, resulting in an increased mean annual bias to 23% and decreased mean R2 to 0.36. Adding random noise to synthetic observations does not significantly decrease model performance except for the experiments with low observation frequency (>12 days). In real‐world experiments, the PBS data assimilation approach underestimates observed IWU by 18.6% when the timing of IWU is known. IWU estimates are consistently significantly higher over irrigated pixels compared to the non‐irrigated pixels, indicating data assimilation skillfully conveys irrigation signals to the LSM.

Upscaling soil moisture from point scale to field scale: Toward a general model

AbstractField‐scale soil moisture measurements are valuable but rarely available because the resolution of most satellite soil moisture products is too coarse, while most in situ sensors provide only point‐scale data. Previous upscaling approaches for such data are mostly site‐specific, and none are suitable to upscale data from the thousands of stations in existing monitoring networks. To help fill this gap, this research aims to develop a more broadly applicable upscaling approach using data from the Marena, Oklahoma, In Situ Sensor Testbed and a cosmic‐ray neutron rover. Rover survey data were used to measure average soil moisture for the ∼64‐ha field on 12 dates in 2019–2020. Statistical modeling was used to identify the soil, terrain, and vegetation properties influencing the relationships between the field‐scale rover data and point‐scale in situ data from six monitoring sites. Site‐specific linear upscaling models estimated the field average soil moisture with root mean squared error (RMSE) values ranging from 0.007 to 0.017 cm3 cm−3, but such models are not transferrable between sites. To create a more general model, Least Absolute Shrinkage and Selection Operator regression was used with a leave‐one‐out cross‐validation approach to identify the key predictors for upscaling. The resulting parsimonious model required only the point‐scale observations and sand content data and achieved RMSE values ranging from 0.006 to 0.031 cm3 cm−3 for the six monitoring sites. The texture‐based model demonstrated reasonable accuracy and is a promising step toward a general model that could be broadly applied for upscaling point‐scale in situ monitoring stations.

Calibration of the ESA CCI-Combined Soil Moisture Products on the Qinghai-Tibet Plateau

Soil moisture (SM) retrieved from satellite and spaceborn sensors provides useful parameters for earth system models (ESMs). The Climate Change Initiative (CCI) SM products released by the European Space Agency have been widely used in many humid/semi-humid climatic regions due to their relatively long-term record. However, the performance of these products in cold and arid regions, such as the Qinghai-Tibetan Plateau (QTP), is largely unknown, necessitating urgent evaluation and calibration in these areas. In this work, we evaluated the reliability and improved the accuracy of the active-passive combined CCI products (CCI-C) using in-situ measured SM contents (SMC) under different underlying surface conditions. First, some conventional models were used to investigate the relationship between the CCI-C and the in-situ observed SMC, yielding similar fitting performances. Next, the random forest method and multiple linear regression were used to contrast the conventional models to calibrate and validate the CCI-C SM product based on the in-situ observed SMC, and the random forest method was found to have the highest accuracy. However, calibration of the CCI-C SM data with the best-performed random forest method based on different spatial zonation methods, e.g., by climate, topography, land cover, and vegetation, resulted in distinct spatial patterns of SM. Compared to a widely-used satellite SM product, namely the Soil Moisture Active Passive (SMAP) SM dataset, the calibrated CCI-C SM data based on climatic and vegetation zonation were larger but had similar spatial patterns. This study also points to the value of the calibrated CCI-C SM product to support land surface studies on the QTP.

Reconstructing long-term global satellite-based soil moisture data using deep learning method

Soil moisture is an essential component for the planetary balance between land surface water and energy. Obtaining long-term global soil moisture data is important for understanding the water cycle changes in the warming climate. To date several satellite soil moisture products are being developed with varying retrieval algorithms, however with considerable missing values. To resolve the data gaps, here we have constructed two global satellite soil moisture products, i.e., the CCI (Climate Change Initiative soil moisture, 1989–2021; CCIori hereafter) and the CM (Correlation Merging soil moisture, 2006–2019; CMori hereafter) products separately using a Convolutional Neural Network (CNN) with autoencoding approach, which considers soil moisture variability in both time and space. The reconstructed datasets, namely CCIrec and CMrec, are cross-evaluated with artificial missing values, and further againt in-situ observations from 12 networks including 485 stations globally, with multiple error metrics of correlation coefficients (R), bias, root mean square errors (RMSE) and unbiased root mean square error (ubRMSE) respectively. The cross-validation results show that the reconstructed missing values have high R (0.987 and 0.974, respectively) and low RMSE (0.015 and 0.032 m3/m3, respectively) with the original ones. The in-situ validation shows that the global mean R between CCIrec (CCIori) and in-situ observations is 0.590 (0.581), RMSE is 0.093 (0.093) m3/m3, ubRMSE is 0.059 (0.058) m3/m3, bias is 0.032 (0.037) m3/m3 respectively; CMrec (CMori) shows quite similar results. The added value of this study is to provide long-term gap-free satellite soil moisture products globally, which helps studies in the fields of hydrology, meteorology, ecology and climate sciences.

Downscaling and validating SMAP soil moisture using a machine learning algorithm over the Awash River basin, Ethiopia.

Microwave remote sensing instrument like Soil Moisture Active Passive ranging from 1 cm to 1 m has provided spatial soil moisture information over the entire globe. However, Soil Moisture Active Passive satellite soil moisture products have a coarse spatial resolution (36km x 36km), limiting its application at the basin scale. This research, subsequently plans to; (1) Evaluate the capability of SAR for the retrieval of surface roughness variables in the Awash River basin; (2) Measure the performance of Random Forest (RF) regression model to downscale SMAP satellite soil moisture over the Awash River basin; (3) validate downscaled soil moisture data with In-situ measurements in the river basin. Random Forest (RF) based downscaling approach was applied to downscale satellite-based soil moisture product (36km x 36km) to fine resolution (1km x 1km). Fine spatial resolution (1km) soil moisture data for the Awash River basin was generated. The downscaled soil moisture product also has a strong spatial correlation with the original one, allowing it to deliver more soil moisture information than the original one. In-situ soil moisture and downscaled soil moisture had a 0.69 Pearson correlation value, compared to a 0.53 correlation between the original and In-situ soil moisture. In-situ soil moisture measurements were obtained from the Middle and Upper Awash sub-basins for validation purposes. In the case of Upper Awash, downscaled soil moisture shows a variation of 0.07 cm3 /cm3, -0.036 cm3 /cm3, and 0.112 cm3 /cm3 with Root Mean Square Error, Bias error, and Unbiased Root Mean Square Error respectively. Following that, the accuracy of downscaled soil moisture against the Middle Awash Sub-basin reveals a variance of 0.1320 cm3 /cm3, -0.033 cm3 /cm3, and 0.148 cm3 /cm3 with Root Mean Square Error, Bias error, and Unbiased Root Mean Square Error respectively. Future studies should take into account the temporal domain of Soil Moisture Active Passive satellite soil moisture product downscaling over the study region.

Influences of Using Different Satellite Soil Moisture Products on SM2RAIN for Rainfall Estimation Across the Tibetan Plateau

Influences of Using Different Satellite Soil Moisture Products on SM2RAIN for Rainfall Estimation Across the Tibetan Plateau

Exploring the Spatial Autocorrelation in Soil Moisture Networks: Analysis of the Bias from Upscaling the Texas Soil Observation Network (TxSON)

Microwave remote sensing such as soil moisture active passive (SMAP) can provide soil moisture data for agricultural and hydrological studies. However, the scales between station-measured and satellite-measured products are quite different, as stations measure on a point scale while satellites have a much larger footprint (e.g., 9 km). Consequently, the validation for soil moisture products, especially inter-comparison between these two types of observations, is quite a challenge. Spatial autocorrelation among the stations could be a contribution of bias, which impacts the dense soil moisture networks when compared with satellite soil moisture products. To examine the effects of spatial autocorrelation to soil moisture upscaling models, this study proposes a spatial analysis approach for soil moisture ground observation upscaling and Thiessen polygon-based block kriging (TBP kriging) and compares the results with three other methods typically used in the current literature: arithmetic average, Thiessen polygon, and Gaussian-weighted average. Using the Texas Soil Observation Network (TxSON) as ground observation, this methodology detects spatial autocorrelation in the distribution of the stations that exist in dense soil moisture networks and improved the spatial modeling accuracy when carrying out upscaling tasks. The study concluded that through TBP kriging the minimum root-mean-square deviation (RMSD) is given where spatial autocorrelation takes place in the soil moisture stations. Through TBP kriging, the station-measured and satellite-measured soil moisture products are more comparable.

Developing a framework for urban flood modeling in Data-poor regions

Forecasting floods is an effective non-engineering measure for flood control. However, for urbanized regions, the lack of drainage data and complex underlying surface conditions make flood forecasting extremely difficult. This paper proposes a framework for urban flood modeling in data-poor regions to address these issues. The drainage capacity of the pipe system was represented by the constant infiltration rate, which was calibrated by coupling satellite soil moisture product and measured flood data to better reflect real drainage conditions. Subsequently, given the complex underlying surface conditions, this framework divides the land use/cover into several dominant urban land use types, which were assigned unique runoff generation and flow confluence parameters in urbanized regions. The framework also takes the impact of dense buildings on water flow into consideration. A building treatment method for structured grids was proposed, which can consider the anisotropy of buildings and scale of the grid. The results showed that it is feasible to estimate drainage capacity using the constant infiltration approach, and the process of soil infiltration is crucial for urban flood forecasting. Compared with the highest resolution publicly available land use/cover dataset, the urban land use types extracted from high-resolution remote sensing images can reveal the runoff generation and flow confluence mechanism more accurately in urbanized regions. This study verified the necessity of considering the impact of buildings in urban flood modeling. The building treatment method of this framework can identify synergistic effects of local terrain and building boundaries on water flow. The results provide a reference for effective flood forecasting in urban regions with poor data.

Spatial downscaling of satellite soil moisture products based on apparent thermal inertia: Considering the effect of vegetation condition

Many applications such as irrigation management and flood predictions require soil moisture (SM) estimates at fine-resolutions. Soil moisture estimates of current satellite missions are normally at coarse spatial resolutions, such as 25–36 km for Soil Moisture and Ocean Salinity (SMOS) SM data. Many spatial downscaling approaches have been developed to get finer resolution SM. Apparent thermal inertia (ATI), as a reliable approximation of thermal inertia (TI) that could be derived from daily fine-resolution optical/thermal remote sensing (RS) data, has been testified to be highly related to SM. However, the empirical relationship between ATI and SM varies with vegetation cover density. The main purpose of this study is to develop an ATI-based SM downscaling method that is free of vegetation cover effects. The study was conducted in Naqu areas in the central Tibetan Plateau (TP) in southwest China, where spatially intensive in-situ SM measurements were routinely obtained. European Space Agency’s Climate Change Initiative (ESA CCI) soil moisture combined product (version 4.2) was used for this study. The fine-resolution (1 km) ATI data were derived from the Collection 6 MODerate resolution Imaging Spectroradiometer (MODIS) products. A modified quantile-quantile (Q-Q) adjustment method was applied to correct the bias of the CCI SM data before downscaling. A non-linear regression model between bias-corrected CCI SM and fine resolution ATI was built to disaggregate the bias-corrected SM to spatial resolution of 1 km. In this model, Enhanced Vegetation Index (EVI) was introduced to globally and quantitatively adjust the vegetation effect in the relationship between SM and ATI. The bias-corrected CCI SM and the downscaled 1 km resolution SM were evaluated using the in-situ SM measurements obtained from the Multi-scale Soil Moisture and Temperature Monitoring Network on the central TP (CTP-SMTMN) in the study area. The results indicate that the proposed modified Q-Q adjustment method effectively reduced the bias of the original CCI SM data (bias = 0 m3/m3). The downscaled 1 km resolution SM shows fine scale spatial variability of soil moisture and preserves the accuracy (R = 0.552) and temporal variability of the bias-corrected CCI SM. The accuracies of the downscaled SM over areas with different vegetation cover show quite good consistency. The uncertainties of the proposed SM spatial downscaling method were comprehensively analyzed. The proposed ATI-based SM downscaling algorithm is applicable to generating representative and consistent high spatial resolution SM over areas with different vegetation cover density.

The first assessment of coarse-pixel soil moisture products within the multi-scale validation framework over Qinghai-Tibet Plateau

The validation of satellite soil moisture (SM) products is challenged by the large scale difference between in situ-satellite based measurements. In order to tackle the significant spatial scale mismatch, this study conducted a multi-scale validation of three typical SM products (i.e., SMOS-IC, SMAP L3, and AMSR2 LPRM) over Qinghai-Tibet Plateau. First, a 25-km better-performing SM dataset was produced by combining three SM products with the extended triple collocation (ETC) and arithmetic mean method. Second, a 500 m SM dataset was derived from the 25-km SM dataset with a random forest-based downscaling model and the high-resolution datasets of other variables. Third, the 500 m SM was evaluated using in situ SM measurements, which was then aggregated to a coarse pixel scale for the assessment of coarse-resolution satellite SM products. Finally, potential factors influencing the accuracy of satellite SM products were investigated. The results indicated that the 25-km merged SM product integrated the characteristics of these three SM products. During the downscaling process, terrain factors, NDVI, and day and night temperature difference were identified as the key variables to derive high-resolution SM, which agreed well with in situ measurements over most monitoring networks. The multi-scale validation results indicate that SMAP L3 and AMSR2 LPRM performs best regarding the median values of the correlation and deviation from the pixel scale reference in the spatial domain, respectively, and SMOS-IC is always the worst. However, when the pixel-based evaluation results were focused, AMSR2 LPRM performs best in most cases, followed by SMAP L3 and SMOS-IC. The accuracy of satellite SM products shows more dependence on slope than elevation, land cover types, and land surface temperature.

Evaluating Satellite Soil Moisture Datasets for Drought Monitoring in Australia and the South-West Pacific

Soil moisture (SM) is critical in monitoring the time-lagged impacts of agrometeorological drought. In Australia and several south-west Pacific Small Island Developing States (SIDS), there are a limited number of in situ SM stations that can adequately assess soil-water availability in a near-real-time context. Satellite SM datasets provide a viable alternative for SM monitoring and agrometeorological drought provision in these regions. In this study, we investigated the performance of Soil Moisture Active Passive (SMAP), Soil Moisture and Ocean Salinity (SMOS), Soil Moisture Operational Products System (SMOPS), SM from the Advanced Microwave Scanning Radiometer 2 (AMSR-2) and SM from the Advanced Scatterometer (ASCAT) over Australia and south-west Pacific SIDS. Products were first evaluated in Australia, given the presence of several in-situ SM monitoring stations and a state-of-the-art hydrological model—the Australian Water Resources Assessment Landscape modelling system (AWRA-L). We further investigated the accuracy of SM satellite datasets in Australia and the south-west Pacific through Triple Collocation analysis with two other SM reference datasets—ERA5 reanalysis SM data and model data from the Global Land Data Assimilation System (GLDAS) dataset. All datasets have differing observation periods ranging from 1911-now, with a common period of observations between 2015–2021. Results demonstrated that ASCAT and SMOS were consistently superior in their performance. Analysis in the six south-west Pacific SIDS indicated reduced performance for all products, with ASCAT and SMOS still performing better than others for most SIDS with median R values ranging between 0.3–0.9. We conducted a case study of the 2015 El Niño and Positive Indian Ocean Dipole-induced drought in Papua New Guinea. It was shown that ASCAT is a valuable dataset indicative of agrometeorological drought for the nation, highlighting the value of using satellite SM products to provide early warning of drought in data-sparse regions in the south-west Pacific.