Reverse Mode Research Articles

Demonstration of normally OFF beta-gallium oxide monolithic bidirectional switch for AC switching applications

In this work, we report on the beta-gallium oxide (β-Ga2O3) monolithic bidirectional switch. The as-fabricated switch works on enhancement mode operation with a threshold voltage of ∼4 V. Maximum drain current density of 1.93 mA/mm is obtained with a drain voltage of 5 V. The bidirectional switch in a bidirectional mode has an ON/OFF current ratio of ∼107 with ON-resistance of 1.11 and 1.09 kΩ · mm in forward and reverse direction, respectively. However, in diode mode, the device shows an ON/OFF current ratio of 1.6 × 108 and 1.4 × 108 in forward and reverse conduction modes, respectively. The fabricated β-Ga2O3 monolithic bidirectional switch is then used to chop a 60 Hz Alternating Current signal at a chopping frequency of 1 kHz, indicating its potential applications in a range of converters.

On Hysteresis In A Variable Pitch Fan Transitioning To Reverse Thrust Mode And Back

Abstract A novel hysteresis phenomenon during the transition to and back from the reverse thrust mode in a Variable Pitch Fan (VPF) is identified and characterised in this work. This is done by using a three-dimensional (3D) fully transient Unsteady Reynolds averaged Navier?Stokes (URANS) with the transitioning fan blade aerofoils simulated by an adaptation of the mesh displacement method. The VPF is modelled to be transitioning in a modern 40000 lbf geared high bypass ratio turbofan engine architecture at "Approach Idle" engine power setting in a typical twin-engine airframe with the flaps, slats, and spoilers set for an aircraft touchdown airspeed of 140 knots. The transition to reverse thrust mode involves flow starvation into the engine, formation of recirculation zones in the bypass duct and the establishment of the reverse stream, all of which occurs in the opposing presence of the free stream flow at aircraft touchdown velocity. The transition back to forward flow mode involves the gradual re-establishment of the free stream which is opposed by the presence of the reverse stream within the engine. It is quantified that in the transition to reverse thrust, the blockage develops with a larger time delay than the disappearance of the blockage during the transition back due to the interplay of the temporal dynamics of fan blade motion and flow field response. The hysteresis phenomena described in this work are critical in properly developing control schedules to adapt for potential bi-stable flow field development during the landing run.

Structure of G protein-coupled receptor GPR1 bound to full-length chemerin adipokine reveals a chemokine-like reverse binding mode.

Chemerin is an adipokine with chemotactic activity to a subset of leukocytes. Chemerin binds to 3 G protein-coupled receptors, including chemokine-like receptor 1 (CMKLR1), G protein-coupled receptor 1 (GPR1), and C-C chemokine receptor-like 2 (CCRL2). Here, we report that GPR1 is capable of Gi signaling when stimulated with full-length chemerin or its C-terminal nonapeptide (C9, YFPGQFAFS). We present high-resolution cryo-EM structures of Gi-coupled GPR1 bound to full-length chemerin and to the C9 peptide, respectively. C9 insertion into the transmembrane (TM) binding pocket is both necessary and sufficient for GPR1 signaling, whereas the full-length chemerin uses its bulky N-terminal core for interaction with a β-strand located at the N-terminus of GPR1. This interaction involves multiple β-strands of full-length chemerin, forming a β-sheet that serves as a "lid" for the TM binding pocket and is energetically expensive to remove as indicated by molecular dynamics simulations with free energy landscape analysis. Combining results from functional assays, our structural model explains why C9 is an activating peptide at GPR1 and how the full-length chemerin uses a "two-site" model for enhanced interaction with GPR1.

Caution for Multidrug Therapy: Significant Baroreflex Afferent Neuroexcitation Coordinated by Multi-Channels/Pumps Under the Threshold Concentration of Yoda1 and Dobutamine Combination

Multi-drug therapies are common in cardiovascular disease intervention; however, io channel/pump coordination has not been tested electrophysiologically. Apparently, inward currents were not elicited by Yoda1/10 nM or Dobutamine/100 nM alone in Ah-type baroreceptor neurons, but were by their combination. To verify this, electroneurography and the whole-cell patch-clamp technique were performed. The results showed that Ah- and C-volley were dramatically increased by the combination at 0.5 V and 5 V, in contrast to A-volley, as consistent with repetitive discharge elicited by step and ramp with markedly reduced current injection/stimulus intensity. Notably, a frequency-dependent action potential (AP) duration was increased with Iberiotoxin-sensitive K+ component. Furthermore, an increased peak in AP measured in phase plots suggested enhanced Na+ influx, cytoplasmic Ca2+ accumulation through reverse mode of Na+/Ca2+ exchanger, and, consequently, functional KCa1.1 up-regulation. Strikingly, the Yoda1- or Dbtm-mediated small/transient Na+/K+-pump currents were robustly increased by their combination, implying a quick ion equilibration that may also be synchronized by hyperpolarization-induced voltage-sag, enabling faster repetitive firing. These novel findings demonstrate multi-channel/pump collaboration together to integrate neurotransmission at the cellular level for baroreflex, providing an afferent explanation in sexual dimorphic blood pressure regulation, and raising the caution regarding the individual drug concentration in multi-drug therapies to optimize efficacy and minimize toxicity.

Study on the transient performance of textured water-lubricated bearings considering different acceleration conditions

This study analyses the transient friction dynamics behavior of water-lubricated bearings (WLBs) with a textured structure, which explains the mechanism of texture structure influencing the hydrodynamic effect of WLB in the physical aspect. A comparison of experimental and numerical data is carried out to validate the proposed mixed lubrication model with a textured structure for WLBs. The effects of texture type, texture angle, acceleration mode, and acceleration time on the nonlinear friction dynamics properties of WLBs are investigated. The result shows that various texture structures exhibit distinct pumping effects and that the optimal friction dynamics performance of WLBs can be achieved by adopting the right herringbone texture and an acceptable texture angle. It is advisable to utilize the reverse S-shaped acceleration mode, as it may efficiently mitigate hydrodynamic shock, minimize frictional contact at the initial startup stage, and control the rotor's vibration in later stages. The brief acceleration time may result in a transient shock that hampers proper lubrication, consequently affecting the stable operation of WLBs. The study's findings offer helpful suggestions for the enhanced design of WLB structures and the mitigation of wear and vibration.

A novel multi-excitation transient vibration framework for coupling three- and one-dimensional pumped storage hydropower shafting systems

In vibration models of shafting systems, the hydraulic excitation is difficult to characterize due to the complex and changeable hydraulic factors. Thus, hydropower units are not well understood in terms of their dynamics and stability control under transient processes. A hydraulic–mechanical–electric multi-excitation transient vibration calculation framework is developed for analyzing the relationship between shafting vibration and internal flow regimes. First, the boundary data from penstocks, tailraces, and hydro-turbine are interacted with using one-dimensional and three-dimensional (1D–3D) coupling; Second, user-defined function secondary development is applied to achieve two-stage guide vane closure and the runner's variable speed rotation; Third, based on the computational fluid dynamics results, a multi-excitation vibration model is established to analyze shafting system characteristics. There is less than 1.2% error between the algorithm and the field test in terms of speed peak values. Under braking or reverse pumping modes, various vortice clusters are generated in the blade channel as well as the cascade, blocking the flow passage and leading to the runner's unbalanced force. Three sudden increases in vibration amplitudes of the shafting system have occurred in the radial direction under load rejection, each corresponded to the runner's stall rotations. The change trend in axial vibration amplitudes, however, is closely related to the change in axial hydraulic thrust. Furthermore, in braking and reverse pumping conditions, the axis trajectory is more complex under the action of multiple coupling factors than when only hydraulic factors are considered.

IF1 is a cold-regulated switch of ATP synthase hydrolytic activity to support thermogenesis in brown fat

While mechanisms controlling uncoupling protein-1 (UCP1) in thermogenic adipocytes play a pivotal role in non-shivering thermogenesis, it remains unclear whether F1Fo-ATP synthase function is also regulated in brown adipose tissue (BAT). Here, we show that inhibitory factor 1 (IF1, encoded by Atp5if1), an inhibitor of ATP synthase hydrolytic activity, is a critical negative regulator of brown adipocyte energy metabolism. In vivo, IF1 levels are diminished in BAT of cold-adapted mice compared to controls. Additionally, the capacity of ATP synthase to generate mitochondrial membrane potential (MMP) through ATP hydrolysis (the so-called “reverse mode” of ATP synthase) is increased in brown fat. In cultured brown adipocytes, IF1 overexpression results in an inability of mitochondria to sustain the MMP upon adrenergic stimulation, leading to a quiescent-like phenotype in brown adipocytes. In mice, adeno-associated virus-mediated IF1 overexpression in BAT suppresses adrenergic-stimulated thermogenesis and decreases mitochondrial respiration in BAT. Taken together, our work identifies downregulation of IF1 upon cold as a critical event for the facilitation of the reverse mode of ATP synthase as well as to enable energetic adaptation of BAT to effectively support non-shivering thermogenesis.

Environmental toxicants modulate disease severity in pediatric metabolic dysfunction-associated steatohepatitis.

Metabolic dysfunction-associated steatotic liver disease (MASLD) is common in children. We hypothesized environmental toxins could drive progression to metabolic dysfunction-associated steatohepatitis (MASH), and assayed serum toxins and metabolites in children with histologically characterized MASLD/MASH. Environmental chemicals, common in household items, perfluoroalkyl substances (PFAS), brominated flame retardants (PBDEs), and metabolic profiles were assayed in children enrolled in the multicenter NASH Clinical Research Network Pediatric Database 2. Mixture models, using repeated holdout weighted quantile sum regression (WQSrh) were run in addition to single chemical/metabolite logistic regression. For metabolomic analyses, random subset version of WQSrh was used for the large number of predictors versus participants. Nominal and false discovery rate (FDR) p-values (two-sided) were computed. Four hundred and thirty-five children distributed across MASH (n = 293) and MASLD (n = 142), with 304 (69.9%) males. Mean (standard deviation) for Nonalcoholic Steatohepatitis Score (NAS) and alanine aminotransferase (ALT) for MASLD were 3.1 (1.0), 67.9 (43.4), and for MASH 4.2 (1.4), 144 (121). There was an inverse association between PFAS/PBDE mixture and MASH versus MASLD, lobular inflammation (p = 0.026), NAS (p = 0.009, FDR p = 0.04), and log-transformed ALT (p = 0.005, FDR p = 0.025) driven by perfluorohexane sulfonate (PFHxS). Metabolites from positive hydrophilic interaction liquid chromatography mode, biliverdin (p = 0.002) and 1-methylhistidine (associated with meat ingestion, p = 0.02) and reverse phase negative mode, hippuric acid (solvent exposure, p = 0.022) significantly associated with MASH. Significant negative PFAS/PBDE mixture effect and odds of MASH were dominated by PHFXS. Several metabolites are significantly associated with MASH which inform mechanistic pathways and could drive key therapeutic and diagnostic strategies in children.

An efficient isogeometric buckling optimization framework for multi-patch laminated shells: Leveraging 3D solid elements, lamination parameters and penalty method

Buckling is a common failure mode of laminated shell structures during service, and isogeometric analysis methods are highly suitable for the buckling analysis due to their accurate geometric modeling capability and high-order continuity. However, the isogeometric buckling analysis for a multi-patch structure and its optimal design still face challenges in computational efficiency. To address this issue, this paper proposes an integrated framework for the buckling optimization of multi-patch laminated shells, which leverages 3D solid elements, lamination parameters, and the penalty coupling method. Solid-shell elements have advantages in shell analysis due to their simplicity, absence of rotational degrees of freedom, and adaptive layering in the thickness direction. Lamination parameters simplify the optimization of fiber orientations in laminated shells by condensing the design variable space and improving the convexity of the optimization problem. The penalty method can handle the coupling in multiple patches at a relatively low cost. Nevertheless, lamination parameters are rarely applied to the case of solid-shell elements. In addition, despite using lamination parameters, the number of design variables for multi-patch structures remains significantly large. To tackle these issues, this study derives the solid-shell formulation in lamination parameters and the sensitivity analysis formulae in the reverse mode. Experiment validation is conducted to assess the accuracy of the proposed method based on lamination parameters with solid elements, the feasibility of the multi-patch optimization model, and the computational efficiency of optimization sensitivity based on the reverse mode compared to the forward counterpart common in the literature.

Reverse Mode Polymer Stabilized Cholesteric Liquid Crystal Flexible Films with Excellent Bending Resistance.

The reverse-mode smart windows, which usually fabricated by polymer stabilized liquid crystal (PSLC), are more practical for scenarios where high transparency is a priority for most of the time. However, the polymer stabilized cholesteric liquid crystal (PSCLC) film exhibits poor spacing stability due to the mobility of CLC molecules during the bending deformation. In this work, a reverse-mode PSCLC flexible film with excellent bending resistance was fabricated by the construction of polymer spacer columns. The effect of the concentration of the polymerizable monomer C6M and chiral dopant R811 on the electro-optical properties and polymer microstructure of the film were studied. The sample B2 containing 3 wt% of C6M and 3 wt% R811 presented the best electro-optical performance. The electrical switch between transparent and opaque state of the flexible PSCLC film after bending not only indicated the excellent electro-optical switching performance, but also demonstrated the outstanding bending resistance of the sample with polymer spacer columns, which makes the PSCLC film containing polymer spacer columns have a great potential to be applied in the field of flexible devices.

Reverse Thrust Aerodynamics of Variable Pitch Fans with Inlet Distortion

Abstract Variable pitch fans can improve the operability of low pressure ratio fan systems by re-pitching the rotor blades. If a variable pitch fan can generate sufficient reverse thrust on landing it also eliminates the need for heavy, cascade-type thrust reversers. However, any reverse thrust generation is impacted by high levels of inlet distortion generated as air is drawn into the exhaust nozzle. This paper uses RANS computations and low-speed rig experiments to explore how a representative inlet distortion from the engine installation affects the aerodynamics and performance of a variable pitch fan operating in reverse thrust mode. The simulations and the experiments show that the distortion from the engine installation leads to a highly three-dimensional flow field with a large recirculation region within the bypass duct. The distortion substantially redistributes the mass flow, thrust and power in the engine. Streamline tracking combined with a power balance analysis reveals highly radial flow within the fan rotor, with almost all the fan power used to drive the recirculating flow in the bypass duct, generating high loss and high total temperature. The recirculation reduces the net mass flow through the engine to around 5% of a uniform inflow case and greatly reduces the effective reverse thrust. With uniform inflow, the net reverse thrust was found to be 35% of the nominal takeoff thrust. With inlet distortion, this was reduced to 20%. This demonstrates the importance of designing and operating variable pitch fan systems to minimise reverse thrust inlet distortion.

Water Transport Management in a Bipolar Membrane for CO2 Electrolysis Application

Bipolar membranes (BPMs) offer significant potential for electrochemical technologies, especially in CO2 electrolysis. Their unique ability to create pH gradients provides optimum chemical microenvironments at the cathode and anode for efficient, cheap and sustainable CO2 electrolysis. However, state-of-the-art BPMs are limited in their performance due to phenomena such as membrane degradation and membrane dehydration leading to low ionic conductivity, and hence their complete potential for various electrochemical technologies is yet to be realized. Previous studies have identified water transport as one of the main factors limiting the performance of BPM. A multi-physics model of BPM can serve as a useful tool to gain a comprehensive understanding of different performance limiting factors and thereafter propose solutions to overcome these limitations. The goal of the present study is to provide model based design guidelines for a BPM that facilitates efficient water transport, making it a suitable candidate for integration into a zero-gap CO2 reduction electrolyzer operating at industrial-grade performance levels.We have built a 1-D continuum model of a BPM kept in an aqueous (bi)carbonate electrolyte solution, incorporating physical phenomena such as water-dependent transport of ions and neutral species, field-enhanced homogeneous reactions (water-dissociation and acid-base reactions) along with CO2 phase transfer reaction at the BPM-aqueous electrolyte interfaces. The continuum model employs Poisson-Nernst-Planck equations to resolve local chemical species concentration. The effect of the electric field on the equilibrium dissociation constants of various charge-generating homogenous reactions is incorporated. This becomes important especially at interfaces within the domain where a sharp increase in electric field is observed. Unlike previous modeling studies, we also incorporate mass-conservation equation for water transport to resolve local water concentration inside the BPM. Local water concentration influences the transport of species in the BPM through their water-dependent activity and diffusivity. The electric potential distribution is resolved by incorporating water-dependent local permittivity of the BPM.Our model investigates both the reverse and forward bias operational modes of the BPM. In alignment with the experimental observation, in the reverse bias regime, the model identifies a distinct initial phase where current density is limited, with the majority of the current carried by protons and hydroxide ions at low overpotentials. As the potential increases, there's a rapid increase in current density, indicating a breakdown regime caused by an electric field-enhanced water dissociation reaction at the BPM interface. At even higher potentials, the polarization curve enters a third phase where the current density saturates characterized by water transport limitation. This aspect of the BPM polarization curve is uniquely captured by our model. Conversely, in the forward bias mode, as expected we do not observe any limitations due to mass transport, since water is generated at the bipolar junction. Here, the model forecasts a saturation of CO2 in the electrolyte, leading to gas bubbles forming at the BPM interface. To address the issue of water transport limitation, we conduct various parametric studies focusing on different membrane characteristics, such as individual layer thicknesses and their ion exchange capacities. The outcomes of these analyses provide crucial guidelines for optimizing these parameters and enhancing water management in BPM-based systems.

Tuning the morphology and electro-optical properties of reverse mode PDLCs using multifunctional acrylates

ABSTRACT Reverse-mode Polymer Dispersed Liquid Crystals (rev-PDLCs) are composite materials generally obtained by the phase separation of dispersions of liquid crystal/monomer mixtures and characterised by the possibility to change on-demand their transmittance in a continuous manner from an initial transparent state to an opaque one by application of an electric field. Rev-PDLCs have found applications in many fields, including large-area smart windows, automotive, and bifunctional devices. In this work, acrylate monomers with different functionality (from 3 to 6) and weight ratios (from 5 to 15%) were used to finely adjust the morphology and electro-optical properties of the rev-PDLCs obtained by photo-polymerisation of an aligned LC/LC monomer mixture. The doping of nematic liquid crystalline monomers with acrylate monomers allowed to finely tune the morphology of rev-PDLC films, which were characterised by highly transparent OFF-states (TOFF always larger than 60%), strongly opaque ON-states (TON always around or lower than 1%), but with contrast ratios, transmittance slopes, threshold and switching fields dependent on the amount and functionality of used monomers. Such results could represent a valid method to overcome the drawback of relatively low materials to be used as starting components in the fabrication of reverse mode dimming films.

Abstract Tu145: Exploring Naltrindole’s hypercontracture attenuating effects during myocardial ischemia via a novel mechanism that produces cardioprotective effects in myocardial ischemia/reperfusion injury

Introduction: Previously, naltrindole (NTI) produced robust cardioprotective effects (e.g.~80% reduction of infarct size) in both ex-vivo (2.5-5µM) and in-vivo (3.75-7.5 mg/kg) rat myocardial ischemia-reperfusion (MIR) injury models. Additionally, we recently showed that NTI 100-200µM attenuated phorbol 12-myristate 13-acetate (PMA) induced polymorphonuclear leukocytes (PMNs) superoxide (SO) release by a novel mechanism of action (MOA) devoid of opioid receptors. Hypothesis: We hypothesize NTI’s novel MOA is a reduction of intracellular calcium (Ca 2+ ). Testing this hypothesis, we conducted isolated perfused MIR assays using KB-R7943(KB). KB is known to reduce intracellular Ca 2+ via inhibition of reverse mode Na + /Ca 2+ exchanger and, therefore, should attenuate myocardial ischemic hypercontracture, infarct size, and left ventricular end diastolic pressure (LVEDP). We predict that both NTI and KB will improve LVEDP and decrease infarct size compared to vehicle (dH 2 O) control and naloxone (NX) used as a negative control. Methods: Hearts were isolated from anesthetized male Sprague Dawley (SD) rats (~300g). We then infused NTI 1.25-5µM, KB 10-20µM, or NX 10µM for 5 min into perfused hearts, just prior to global I(30min)/R(45min). Cardiac left ventricular function was measured via a pressure transducer and infarct size using 1% triphenyltetrazolium chloride staining in the MIR assay. Data were analyzed using ANOVA and Fishers post-hoc analysis, with p<0.05 considered statistically significant. Results: MIR assay: NTI 5µM, 2.5µM, 1.25µM and KB 20 µM reduced infarct size (4.8±3%, n=5, p<0.05), (6.8±0.8%, n=6, p<0.05), (12.2±3%, n=5), and (2.9±2%, n=5, p<0.05) respectively compared to vehicle (14.1±2%, n=9) and NX 10µM controls (18±3%, n=3). NTI 5 µM and KB 20 µM had significantly improved LVEDP to (32.4±11%, n=5, p<0.05) and (22.8±4%, n=5, p<0.05) respectively compared to vehicle control (72.4±6%, n=9) and NX 10µM controls (54.2±8%, n=3) Conclusion: Both NTI (2.5µM, 5µM) and KB (20µM) reduced infarct size and improved LVEDP. The novel MOA of NTI may be mediated via a reduction in intracellular Ca 2+ during myocardial ischemia. The infarct reducing effect of NTI can benefit patients undergoing elective PCI, CABG, and transplant procedures.

Abstract We092: Naltrindole Attenuates Superoxide Release in Polymorphonuclear Leukocytes by a Novel Mechanism devoid of Delta opioid receptor antagonism Related to Reduced Intracellular Calcium Levels

Introduction: Naltrindole (NTI), known as a delta opioid receptor antagonist, inhibited phorbol 12-myristate 13-acetate (PMA) induced superoxide (SO) release in polymorphonuclear leukocytes (PMNs). PMNs do not express opioid receptors. We propose NTI reduces PMN SO by reducing intracellular calcium (Ca 2+ ). To test this hypothesis, we did experiments using KB-R7943 (KB) as a positive control, known to reduce intracellular Ca 2+ via inhibition of the reverse mode Na + /Ca 2+ exchanger. Naloxone (NX), a broad-spectrum opioid receptor antagonist, was used as a negative control. We predict that NTI will diminish PMA-induced PMN SO release similar to KB, while NX will have no effect, and that there will be no difference in cell viability compared to vehicle controls. Methods: Male Sprague Dawley (SD) rat PMNs (5x10 6 ) were incubated for 15 min at 37 o C in the presence or absence (dH 2 O vehicle control) of NTI (10 - 200 µM), KB (5-20 µM), and NX (100-200 µM). PMN SO release was measured by the change in absorbance at 550 nm over 420 sec via ferricytochrome c reduction after PMA stimulation (100 nM). The cell viability was determined microscopically by 0.2% trypan blue exclusion at the end of PMN SO release assay. Data were analyzed using ANOVA Fisher’s PLSD post-hoc test. Results: NTI significantly decreased PMN SO release at 200 μM (n=10, 0.196±0.06, p<0.05) compared to vehicle control (n=22, 0.731±0.07) or NX 100/200 μM (n=3, 0.593±0.06), and NTI at 100 μM (n=7, 0.461±0.08, p<0.05) versus vehicle control. Likewise, KB significantly decreased PMN SO release at 20 μM (n=7, 0.507±0.07), 10 μM (n=7, 0.552±0.07), and 5 μM (n=5, 0.615±0.11) compared to vehicle control (n=10, 0.908±0.07). Cell viability was statistically similar (80-90±5%) among all study groups. Conclusion: NTI (10-200 μM) and KB (5-20 µM) exhibited concentration-dependent effects in reducing PMN SO release without compromising cell viability. The results suggest that the novel effect of NTI maybe mediated through a reduction in intracellular Ca 2+ and independent of delta opioid receptor antagonism. These results are consistent with the effects of NTI, KB and NX in myocardial ischemia/reperfusion injuries. Future studies will assess the effects of NTI on ROS attenuation in human umbilical vein endothelial cells.

Development of novel thermal diode inspired by the structure of venous valve

To increase the unidirectional heat transfer capability of a thermal diode, a novel thermal diode with unidirectional movable valves as vapor channel is proposed based on the structure of venous valves. The thermal performance of this bionic thermal diode was experimentally investigated under different working conditions. The results demonstrate that the bionic thermal diode exhibits a high thermal rectification ratio and strong stability. The best thermal rectification ratio is 10.79, with a forward thermal resistance of 0.26 °C/W and a reverse thermal resistance of 2.86 °C/W, at a heating power of 15 W and a filling ratio of 15 %. The temperature distribution indicated that, under the reverse heat transfer mode, the vapor was obstructed at the first valve, leading to the high thermal resistance of thermal diode. Additionally, the effect of inclined angle on the thermal performance of thermal diode was also investigated. This study provides a novel approach for the design of thermal diodes.

Hysteresis in radio frequency capacitively coupled CF4 plasmas

Based on experiments and simulations, various plasma parameters are found to undergo a hysteresis as a function of the driving voltage amplitude in capacitively coupled CF4 discharges. Phase Resolved Optical Emission Spectroscopy reveals that the discharge operates in a hybrid combination of the drift-ambipolar and α-mode at low voltage. In this mode, the electric field and mean electron energy are high in the electronegative plasma bulk region. As the cross section for electron attachment is appreciable only at high electron energies, this mode results in strong negative ion production and keeps the electron density low as well as the mode of plasma operation stable, when the voltage is increased moderately. Increasing the driving voltage amplitude further ultimately induces a mode transition into a pure α-mode, once the electron density increases strongly. Decreasing the voltage again results in a reverse mode transition at a lower voltage compared to the previous mode transition, because the electron density is now initially high in the bulk and, thus, the bulk electric field and mean electron energy are low resulting in inefficient generation of negative ions via electron attachment. This keeps the electron density high even at lower driving voltages. This effect leads to the emergence of two steady states of plasma operation within a certain voltage range. The different electron energy distribution functions in these two states result in markedly different generation and density profiles of F atoms, with higher values occurring in the increasing voltage branch of the hysteresis. The ion flux and mean energy at the electrodes also differ. The voltage range, where the hysteresis occurs, is affected by the ion induced secondary electron coefficient (γ). A larger value of γ results in a shift of the hysteresis voltage range towards lower values.

МОДЕЛЮВАННЯ ЕНЕРГОЕФЕКТИВНОСТІ ЖИТЛОВОЇ БУДІВЛІ ЗА УМОВ РІЗНИХ ДЖЕРЕЛ ТЕПЛОВОЇ ЕНЕРГІЇ

The paper presents the results of modeling the process of energy consumption in public, residential, and commercial buildings as a result of the use of various sources of thermal energy. Buildings with such energy sources as: a) a low-temperature gas boiler with a capacity of up to 120 kW for the needs of heat supply of a residential building and freon air conditioning systems for the needs of cooling the building; b) a gas condensing boiler with a thermal capacity of up to 120 kW with a temperature regime of 55/45°C for heat supply and freon air conditioning systems for cooling; c) reversible heat pumping unit of the “ground-water” type with a temperature regime of 35/28°C for the needs of the heating and cooling system and a reversible heat pumping machine with a regime of 55/45°C for the needs of hot water supply; d) a reversible air-to-air heat pump for heating and cooling systems and electric boilers for hot water supply; e) a biomass solid fuel boiler with manual fuel loading with a heat output of more than 100 kW for heat supply and freon systems for cooling; f) a fuel pellet boiler with automatic mechanized fuel loading with a heat output of more than 100 kW for building heating and cooling and freon systems for cooling; g) centralized heating system of the building. The results of calculations of the specific primary energy consumption and specific greenhouse gas emissions for each of the above heat sources are presented. It is established that biomass boilers have the lowest values of primary energy consumption and specific greenhouse gas emissions. The lowest efficiency is achieved by a district heating system with a centralized energy source. The modeling was conducted for the climatic conditions of Vinnytsia. At the same time, the disadvantage of using solid fuel boilers is the limitation of their use in densely populated areas, which is explained by the complexity of flue gas cleaning and regular biomass supply. Therefore, it has been determined that the most efficient source of thermal energy for buildings of various types to achieve the standardized energy efficiency indicators is a ground-to-water heat pump system. This installation, along with providing buildings with thermal energy, allows for cooling in the warm season, operating in reverse mode.

Multimodal soft valve enables physical responsiveness for preemptive resilience of soft robots.

Resilience is crucial for the self-preservation of biological systems: Humans recover from wounds thanks to an immune system that autonomously enacts a multistage response to promote healing. Similar passive mechanisms can enable pneumatic soft robots to overcome common faults such as bursts originating from punctures or overpressurization. Recent technological advancements, ranging from fault-tolerant controllers for robot reconfigurability to self-healing materials, have paved the way for robot resilience. However, these techniques require powerful processors and large datasets or external hardware. How to extend the operational life span of damaged soft robots with minimal computational and physical resources remains unclear. In this study, we demonstrated a multimodal pneumatic soft valve capable of passive resilient reactions, triggered by faults, to prevent or isolate damage in soft robots. In its forward operation mode, the valve, requiring a single supply pressure, isolated punctured soft inflatable elements from the rest of the soft robot in as fast as 21 milliseconds. In its reverse operation mode, the valve can passively protect robots against overpressurization caused by external disturbances, avoiding plastic deformations and bursts. Furthermore, the two modes combined enabled the creation of an endogenously controlled valve capable of autonomous burst isolation. We demonstrated the passive and quick response and the possibility of monolithic integration of the soft valve in grippers and crawling robots. The approach proposed in this study provides a distributed small-footprint alternative to controller-based resilience and is expected to help soft robots achieve uninterrupted long-lasting operation.

Experiments and three-dimensional flow simulations on twin-screw pumps operated as control valves for energy recovery

This study explores the characteristics of twin-screw pumps when operated in turbine, i.e., reverse mode as an alternative to traditional control valves in piping systems for recovering energy. Experimental and flow simulation methods are employed. By an overset grid technique, unsteady three-dimensional (3D) flow simulations are conducted, ensuring high cell quality and high spatial resolution, particularly in wall proximity and within the gaps. To assess viscosity effects, pump and turbine mode characteristics are analyzed for water and oil. Compared to water, a pronounced reduction of the flow rate dependence on pressure difference is revealed for highly viscous oil. The gap flow in oil is significantly affected by the spindles’ rotational speed and direction, whereas water displays minimal influence. Analyzing the variation in gap sizes, a 50% reduction in the minimum flank gap width leads to a slight rise in volumetric efficiency with negligible overall efficiency effects. Our findings underscore that utilizing twin-screw pumps as turbines for high-viscosity fluids can potentially recover up to 50% of the energy instead of dissipating it by using conventional control valves.