Resonance Frequency Difference Research Articles

Aging Characterization of Modified Insulating Paper Based on the Transmission Characteristics of Microstrip Resonant Sensors

In this paper, the aging characterization of a kind of insulating paper modified by magnetron sputtering MgO particles based on a microstrip resonant sensor was presented. Firstly, the modified insulating paper with 0, 15 and 30 min MgO particle sputtering times was prepared by a magnetron sputtering device. After that, the properties of the modified insulating paper with different sputtering times were analyzed through microscopic characterization, infrared spectrum, polymerization degree, dielectric constant, AC breakdown strength and thermal aging experiments. The results show that the dielectric constant of the modified insulating paper decreased obviously, the AC breakdown strength increased and the thermal aging resistance was better after 15 min of sputtering. The overall performance of the modified insulating paper after 30 min of sputtering is reduced due to excessive sputtering. In addition, microstrip resonant sensors are introduced to characterize the thermal aging degree of the modified insulating paper, and two microstrip resonant sensors are prepared: a complementary split ring resonator (CSRR) and an interdigital-capacitor-shaped defected ground structure resonator (IDCS-DGS). The resonance frequency deviation of the modified insulating paper samples after aging was measured by microstrip resonance sensors to show the influence of aging temperature on aging degree. The experimental results show that the test results of the microstrip resonance sensors are in good agreement with the traditional characterization methods and can characterize the various aging stages of the modified insulating paper to a certain extent, which proves the feasibility of the characterization method.

Frequency tuning and automatic frequency tracking of shunted piezoelectric transducers

Piezoelectric ultrasonic transducers, vital in medical devices and aerospace, often face challenges like resonant frequency shifts and impedance variations affecting their operational efficiency. This paper introduces a shunted piezoelectric transducer which could tune itself by digitally programmable inductance. A transformer and inductance-capacitance matching network ensures enhanced compatibility and impedance management. Proposing a fuzzy PI-based phase control method achieves resonant frequency tracking, synchronizing operational frequency with the transducer. In contrast to traditional methods, our approach enables faster and more precise fine-tuning, detecting and rectifying real-world deviations for optimal performance. A comprehensive experimental validation, based on fundamental knowledge analysis, confirms the feasibility and superiority of our proposed method, and the commonly encountered issues of resonance frequency deviation and impedance variation in high-power piezoelectric transducer applications can be effectively mitigated.

Performance regulation of high-precision wireless passive yarn sensor based on normal mode helical dipole antenna

Stable and reliable sensing performance was required for high-precision wireless passive yarn sensor based on normal mode helical dipole antenna (NMHDA). The actual helical pitch of NMHDA was non-uniform due to manufacturing process, and the previous equivalent impedance model for uniform NMHDA, i.e., wire-loop model, was oversimplified, resulting in inaccurate predicted reactance and sensing performance of yarn sensor. This work combined the circular polarization principle and the asymmetric structure of non-uniform NMHDA to build the wire-loop-wire model. Based on the wire-loop-wire model, the parametric expression of NMHDA impedance and resonant frequency were obtained, and the results predicted by wire-loop model and wire-loop-wire model were compared with the measured one. Furthermore, to demonstrate the practicality of wire-loop-wire model and parametric resonant frequency expression, the impact of helical pitch uniformity on resonant frequency was discussed in terms of the statistical characteristics of prototype helical pitch, and also the parametric expression was applied to design wireless passive yarn sensors with expected working property. It was found that the wire-loop-wire model incorporating the asymmetric structure accurately described the impedance characteristics of the NMHDA with non-uniform helical pitches, and the maximum predicted deviation of resonant frequency was reduced to 1 MHz. The steady long reading range (19.42 ± 0.09 m) of wireless passive yarn sensors prototype demonstrated the capacity of wire-loop-wire model in designing high-precision sensor. Generally, this paper successfully built the wire-loop-wire model for NMHDA with non-uniform helical pitches, and provided a practical tool for designing e-textile devices with NMHDA.

Terahertz reconfigurable metasensor for specific recognition multiple and mixed chemical substances based on AIT fingerprint enhancement

Terahertz (THz) fingerprint metasensing is an effective method to identify chemical substances in a rapid and non-destructive way. Currently, two main principles are used in THz metasensing: the change of the real part of permittivity causing the dip resonance frequency deviation, and the fingerprint peak of the imaginary part of permittivity causing the dip resonance splitting (absorption induced transparency, AIT). Most previous work investigated AIT detection for only single chemical substance. The suitable AIT metasensor structure are still required for simultaneously measurement of multiple and mixture chemical substances. In this manuscript, we proposed the N-order concentric rings metasensor for specific recognition multiple and mixed chemical substances based on AIT fingerprint enhancement. The structure has broadband multiple plasmonic resonance dips which are generated by near field dipole resonances. The equivalent circuit model was built to realize the reconfigurable function. Then, 5-order concentric rings structure was designed and fabricated for simultaneously specific recognition of four chemical substances (α-lactose, benzoic acid, vitamin B2 and 2, 5-dichloroanline). The influence of the real and imaginary part of the chemical substances' permittivity on AIT effect had discussed in details. Simulation results indicated that the frequency-deviation of the resonance dip can be stabilized and will not be changed when the concentration of chemical substances is over 20 mg/mL. As shifted plasmonic resonance peaks match the chemical substances’ imaginary part of permittivity fingerprint spectra, the perfect AIT effect can be realized. The metasensor can simultaneously and non-destructively conduct a specific detection of α-lactose, benzoic acid, vitamin B2 and 2,5-dichloroanline, and their mixture. The limit of detections of α-lactose, benzoic acid, vitamin B2 and 2,5-dichloroanline are 8.61 mg/mL, 6.96 mg/mL, 7.54 mg/mL and 8.35 mg/mL, respectively. Also, the sensitivity of the metasensor can reach 0.00211, 0.00208, 0.00211 and 0.00219 (unit: 1/mg/mL), respectively. By utilizing one-way analysis of variance method, the possibility of recognition error for each chemical substance is lower than 0.001. Our metasensor provides a novel and accurate platform for THz fingerprint sensing.

Resonant Frequency Deviation Analysis and Modified Notch Filter-Based Active Damping for SiC-Based PMSM Drive With Sine Wave Filter

In the permanent-magnet synchronous machine (PMSM) drive system, the adoption of silicon carbide (SiC) devices brings up new challenges, such as overvoltage, electromagnetic interference emission, and bearing current. To surmount these barriers, the <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">LC</i> filter designed as the sine wave filter can be introduced into the machine drive system. However, filter and stator inductance can create unwanted electrical resonance issues. For the <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">LC</i> -equipped PMSM drive system, there are two main factors that cause the drift of resonant frequency and change of stable region: (1) synchronous coordinate transformation with variable fundamental frequency, (2) parameter variations due to the magnetic saturation effect. In this paper, the deviation of resonant frequency caused by coordinate transformation is discussed. Then, the inherent damping effects and stability range in the rotating reference frame are derived in detail. Furthermore, considering the parameter mismatch disturbances, an active damping method based on the enhanced notch filter is presented, of which notch frequency is designed lag behind the nominal resonant frequency. The accurate discretization method and theoretical stability analysis in discrete <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">z</i> -domain are conducted. The experimental results are presented to verify the effectiveness and robustness of the proposed analysis and method.

Modeling the load capacity of frequency-tracked rotary ultrasonic machining system

Rotary ultrasonic machining (RUM) is a superior processing method for difficult-to-cut materials. It employs a large enough ultrasonic amplitude of the tool to enable its unique intermittent cutting mechanics. The critical cutting force is a vital performance indicator to characterize the load capacity for the RUM system. If the cutting force exceeds a critical value, the ultrasonic amplitude of the tool will be restrained as a minimal value due to the deviation of resonant frequency, resulting in the performance loss of RUM. However, the current understanding of critical cutting force only applies to the RUM system without a frequency-tracking module. This study tries to fill the knowledge gap regarding the load capacity of the frequency-tracked RUM system. First, the dependency of actual ultrasonic amplitude on the cutting force is modeled based on the RUM system's input-output relation that uses a frequency-tracking module. Then, the critical cutting force is derived by inverse solving the above model Afterward, we propose a measurement method of the actual ultrasonic amplitude under load by observing the tool vibration trace on the machined surface using a diamond indenter. Moreover, an easy-to-operate experimental method to measure the critical cutting force is developed. Finally, serial load experiments of the RUM system under different driving voltages are performed. The experimental results verified the models of actual ultrasonic amplitude and the critical cutting force. Based on the model, the influences of the electrical and mechanical design of the frequency-tracked RUM system on the critical cutting force are analyzed.

An AlN Piezoelectric Micromachined Ultrasonic Transducer-Based Liquid Density Sensor

As an important physical parameter of liquids, the liquid density plays an important role in many applications. As a result, the development of liquid density sensors is critical. However, current liquid density sensors have drawbacks, such as large size of conventional liquid density sensors, low quality factor of microcantilever beam structures, low sensitivity of quartz crystal tuning forks, and high operating frequency requirement of surface-acoustic-wave Love-mode resonators. In this article, we report an aluminum nitride (AlN) piezoelectric micromachined ultrasonic transducer (PMUT)-based liquid density sensor to mitigate the aforementioned drawbacks of traditional liquid density sensors. The PMUT sensor utilizes CMOS-compatible AlN as the piezoelectric material. This sensor operates by measuring the change in resonant frequency of the PMUT to calculate the liquid density. In an experiment, the resonance of the PMUT sensor is measured by a digital holographic microscope (DHM), which allows direct measurement of the PMUT surface displacement, providing intuitive vibration amplitude and mode. Moreover, the DHM-based optical measurement approach has a higher sensitivity than the conventional electrical impedance-based measurement approach, allowing measurement of weak PMUT vibrations in dense liquids. The quality factor ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${Q}$ </tex-math></inline-formula> ) value of the PMUT sensor is measured to be 49.38 in water. A high sensitivity of 12.71 kHz/( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\text{g}\cdot $ </tex-math></inline-formula> cm <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$^{-{3}}$ </tex-math></inline-formula> ) was determined for this sensor by measuring the resonant frequencies immersed in different glycerol aqueous solutions. We measured 12 PMUTs and the maximum deviation of resonant frequency between different PMUTs is 9.85%. For the first time, the resolution of the PMUT density sensor is determined to be <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$5.9\times 10^{-{4}}\,\,\text{g}\cdot $ </tex-math></inline-formula> cm <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$^{-{3}}$ </tex-math></inline-formula> .

Frequency offset suppression method for wireless power transfer based on nonlinear resonant network

SummaryIn magnetically resonant wireless power transfer (MR‐WPT) systems, transmitter, and receiver usually operate at the same resonant frequency. However, parameters of inductor, capacitor, or other components are susceptible to changes due to environmental factors and cause resonant frequency deviation. This would lead to decrease of transmission performance. To solve the problem, a wireless power transfer system based on a nonlinear compensation network is proposed to suppress frequency offset. The modeling of the nonlinear MR‐WPT system is first established. On this basis, the mathematical equation of the equivalent nonlinear circuit is deduced and the amplitude‐frequency response characteristics are analyzed. The influence of inductance parameter on the nonlinear characteristic is studied. Furthermore, the effects of excitation amplitude, compensation capacitance, load, and magnetic ring turns on the operating characteristics of the nonlinear resonant circuit are analyzed. The proposed nonlinear resonant wireless power transfer system is constructed and is experimentally studied. Compared with the traditional linear MR‐WPT system, the results show that frequency offset can be effectively suppressed, which ensures efficient transmission performance with the proposed method.

An FSS structure with a band‐stop performance for UWB applications

AbstractIn this paper, a frequency selective surface (FSS) structure with a band‐stop performance for ultra‐wideband (UWB) applications is introduced. The unit cell of the FSS structure consists of a combination of a square loop, a ring loop, and a cross dipole with four gaps. The unit cell has 0.115λg × 0.115λg size where λg is the wavelength in the substrate corresponding to the minimum frequency (2.79 GHz) of the operating band. The bandwidth of the FSS design is from 2.79 to 10.81 GHz frequencies (at normal incidence and |S21| &lt; −3 dB criterion) which covers all UWB bands. The introduced FSS structure has angular stability up to 80° incident angles both TM and TE polarizations due to the small size of the unit cell. The highest resonance frequency deviation is 0.08% at 80° and this value is quite low. The proposed FSS structure was fabricated and the results obtained through simulations were supported by the measurement results.

Impedance modeling and analysis of multi-stacked on-chip power distribution network in 3D ICs

An accurate impedance modeling of a multi-stacked on-chip power distributed network (PDN) based on through-silicon-vias (TSVs) is vitally important to estimate the electrical performance in three-dimensional integrated circuits (3D ICs). This paper proposes a method for calculating the impedance matrix of the multi-stacked on-chip PDN, which mainly consists of arbitrarily distributed TSVs and grid-type on-chip PDNs. First, a real stack-up structure of a multi-stacked on-chip PDN is separated into discrete components intentionally. Then, the equivalent lumped circuit models of all discrete components are assembled into a whole to build the transmission matrix of the multi-stacked on-chip PDN through the relationship between the nodal voltage and the nodal current. Finally, the impedance matrix can be derived through the transmission matrix. In this paper, the coupling of the arbitrarily distributed TSVs and the distributional effect of the on-chip PDN are considered in the impedance matrix through the transmission matrix method (TMM). The proposed method replaces the simulation of the complex equivalent circuit model with the matrix calculation. The verification results show that the deviation of resonant frequency is about 6 $$\%$$ and the conversation of the simulation time is about 99.9 $$\%$$ compared with the HFSS model. It can accurately and quickly calculate the impedance of the multi-stacked on-chip PDN.

Development and tuning of the microwave resonant cavity of a cryogenic cesium atomic fountain clock.

A cryogenic cesium atomic fountain clock is a novel clock with the microwave cavity and atomic free flight region placed in liquid nitrogen. On the one hand, the blackbody radiation shift is reduced at cryogenic temperature. On the other hand, the vacuum in the atomic free flight region is optimized, and the background gas collision shift reduced. The microwave resonant cavity is the most important unit in a cryogenic cesium atomic fountain clock. Through theoretical and simulative investigation, this study designs the configuration and dimensions for an optimized microwave cavity. Concurrently, experiments reveal the effects of temperature, pressure, humidity, and other factors on the resonant frequency of the microwave cavity. Combining the theoretical and experimental study, we obtain the resonant frequency difference between the microwave cavity in a cryogenic vacuum and at room temperature and ambient pressure. By subtracting this frequency difference, we adjust the microwave cavity for room temperature and ambient pressure, then vacuumize and immerse it in liquid nitrogen for verification and fine tuning. Finally, we determine that the microwave cavity resonant frequency deviation from the clock transition frequency is 10 kHz with an unloaded quality factor of 25 000, which meets the application requirements of the cryogenic cesium atomic fountain clock.

Improved thermoacoustic sound projectors by vibration mode modification

The problem of coupled panel-cavity vibrations is addressed by studying the resonance modes in high power, low frequency, encapsulated thermoacoustic sound projectors using scanning laser vibrometry and sound pressure measurements. We fabricated and analyzed the performance of large area thermoacoustic sound projectors based on freestanding carbon nanotube sheets, encapsulated between a heat sink and various rigid vibrating plates. For thin, simply-supported vibrating plates we observed a strong deviation of resonance frequency and sound intensity from theoretical prediction for in vacuo plates. The domination of symmetric, odd modes for thin plates, with substantially improved sound radiation, is attributed to the coupled panel-cavity modes produced by harmonically varying pressure within the cavity. The observed modified mode shapes result from a minimum energy principle, wherein the potential energy stored in the entrained gas is minimized by reducing the overall change of the cavity gas volume. The effect of plate and cavity thickness on thermoacoustic projector performance in air is described for various devices. The optimized ultralight, low volume sound projectors can generate a remarkably high sound pressure level in air of over 120 dB re 20 μPa @ 1 m in a frequency range of 500 - 3000 Hz.

Miniaturized frequency selective surface with high angular stability

Abstract In this paper, a miniaturized bandstop frequency selective surface (FSS) with high angular stability is presented. Each FSS element consists of four sets each consisting eight octagonal concentric interconnected loops. The four sets are connected with each other through outermost octagonal loop. The unit size is miniaturized to 0.066 λ0 at the resonant frequency of 1.79 GHz. The proposed configuration achieves excellent angular stability (only 0.025 GHz resonant frequency deviation is observed upto 83° oblique angles). The working mechanism of FSS is explained with the help of equivalent circuit model (ECM), electric field distribution, and corresponding surface current distribution. A prototype of the designed bandstop FSS is fabricated to verify the simulated frequency response. The experimental results are consistent with the simulation results. Simple geometry, low profile, high angular stability, and compact cell size are prominent features of the proposed structure.

Understanding and minimizing resonance frequency deviations on a 4-in. kilo-pixel kinetic inductance detector array

One of the advantages of kinetic inductance detectors is their intrinsic frequency domain multiplexing capability. However, fabrication imperfections usually give rise to resonance frequency deviations, which create frequency collision and limit the array yield. Here, we study the resonance frequency deviation of a 4-in. kilo-pixel lumped-element kinetic inductance detector (LEKID) array using optical mapping. Using the measured resonator dimensions and film thickness, the fractional deviation can be explained within ±25×10−3, whereas the residual deviation is due to variation of electric film properties. Using the capacitor trimming technique, the fractional deviation is decreased by a factor of 14. The yield of the trimming process is found to be 97%. The mapping yield, measured under a 110 K background, is improved from 69% to 76%, which can be further improved to 81% after updating our readout system. With the improvement in yield, the capacitor trimming technique may benefit future large-format LEKID arrays.

The resonant frequency measurement method for superconducting cavity with Lorentz force detuning

The precise measurement of resonance frequency is very important to tune the cavity and stabilize the RF field. The minimal-reflection method is usually used to measure the cavity resonance frequency, but the accuracy may not meet the stability requirement for the superconducting cavity with narrow bandwidth. The falling-edge method with high precision has been used for the resonance frequency measurement of the normal conducting cavity, but it cannot be used directly for the superconducting cavity due to the effect of Lorentz Force Detuning (LFD). This paper presents the solution for applying the falling-edge method to measure the resonance frequency of superconducting cavity with LFD. The periodic iteration algorithm is developed to calculate the frequency detuning and phase shift caused by the dynamic Lorentz Force within RF falling-edge. The phase shift due to the deviation of initial resonance frequency is derived by subtracting the LFD item from the phase measurement, and the initial resonance frequency can be determined finally. The method has been tested on the superconducting cavity at CAFE facility, and the effectiveness has been demonstrated.

Bending Analysis of Polymer-Based Flexible Antennas for Wearable, General IoT Applications: A Review

Flexible substrates have become essential in order to provide increased flexibility in wearable sensors, including polymers, plastic, paper, textiles and fabrics. This study is to comprehensively summarize the bending capabilities of flexible polymer substrate for general Internet of Things (IoTs) applications. The basic premise is to investigate the flexibility and bending ability of polymer materials as well as their tendency to withstand deformation. We start by providing a chronological order of flexible materials which have been used during the last few decades. In the future, the IoT is expected to support a diverse set of technologies to enable new applications through wireless connectivity. For wearable IoTs, flexibility and bending capabilities of materials are required. This paper provides an overview of some abundantly used polymer substrates and compares their physical, electrical and mechanical properties. It also studies the bending effects on the radiation performance of antenna designs that use polymer substrates. Moreover, we explore a selection of flexible materials for flexible antennas in IoT applications, namely Polyimides (PI), Polyethylene Terephthalate (PET), Polydimethylsiloxane (PDMS), Polytetrafluoroethylene (PTFE), Rogers RT/Duroid and Liquid Crystal Polymer (LCP). The study includes a complete analysis of bending and folding effects on the radiation characteristics such as S-parameters, resonant frequency deviation and the impedance mismatch with feedline of the flexible polymer substrate microstrip antennas. These flexible polymer substrates are useful for future wearable devices and general IoT applications.

Characterization of the koch fractal hexagonal loop frequency selective surface for X-band application

&lt;p&gt;This paper presented the bandstop Koch fractal hexagonal loop frequency selective surface (FSS) for the X-band application. The simulated transmission coefficient response (S_21) had been obtained by using CST software. The proposed Koch fractal hexagonal loop FSS structure is highly insensitive towards angular stability and also incident polarization up to 60 degree , with deviation of resonant frequency, f_r below than 1%. The parametric analysis on the effect of the periodicity, width, and height of the fractal FSS structure on the S_21 has been illustrated and discussed thoroughly.&lt;/p&gt;

Design and analysis of angular stable antipodal F‐type frequency selective surface with multi‐band characteristics

This article presents frequency selective surface (FSS) with multi-band characteristics that features tri band band-stop and dual-band passband filter. The proposed FSS unit cell comprises the F-type resonance elements disposed of antipodal (diametrically opposed to) one to another on both layer and a square loop surrounding all resonators on the top layer of the dielectric substrate. The structure is specifically designed to filter out some extensively used broadband communication signals, such as, WiMAX and WLAN while enabling C-band satellite communication in the earth station and provides three stopbands operating at 2.4, 5.2, and 5.9 GHz besides two passbands of 4.1 and 5.5 GHz. Although this structure has a multi-band structure, it exhibits high stable performance for oblique incidence ranging from 0° to 60° for both transverse electric (TE) and transverse magnetic (TM) polarizations. Considering the resonant frequency deviation (RFD) at the incidence waves with different angles of arrivals, it was found that RFD at 60° is less than 0.6% on average and very low when compared with existing studies about multi-band FSS. The detailed equivalent-circuit model (ECM) is employed to predict and analyze the transmission characteristic of the proposed structure, and a good agreement between the simulated and measured transmission coefficients is obtained.

Design of Readout Circuit with Quadrature Error and Auxiliary PLL for MEMS Vibratory Gyroscope.

Traditional MEMS gyroscope readout eliminates quadrature error and relies on the phase relationship between the drive displacement and the Coriolis position to accomplish a coherent demodulation. This scheme shows some risk, especially for a mode-matching gyro. If only a slight resonant frequency deviation between the drive and sense mode occurs, a dramatic change in the phase relationship follows, which leads to a wrong demodulation. To solve this, this paper proposes a new readout based on the quadrature error and an auxiliary phase-locked loop (PLL). By tuning the phase shifter in the sense-mode circuit, letting the quadrature error and the carrier of the mixer be in 90° phase alignment, the Coriolis was simultaneously in phase with the carrier. Hence, the demodulation was accomplished. The carrier comes from the PLL output of the drive-mode circuit due to its low jitter and independence of the work mode of the gyro. Moreover, an auxiliary PLL is used to filter the quadrature error to enhance the phase alignment accuracy. Through an elaborate design, a printed circuit board was used to verify the proposed idea. The experimental results show the readout circuit functioned well. The scale factor of the gyro was 6.8 mV/°/s, and the bias instability was 204°/h.

A Novel Microwave Phased- and Perturbation-Injection-Locked Sensor With Self-Oscillating Complementary Split-Ring Resonator for Finger and Wrist Pulse Detection

In this article, a novel microwave phased- and perturbation-injection-locked (PPIL) sensor with a self-oscillating complementary split-ring resonator (SO-CSRR) is proposed for finger and wrist pulse detection. This SO-CSRR is designed to generate a concentrated electric field in the near-field region and then senses the skin-surface variations of the fingertip or the wrist artery, which are caused by the periodic capillary or vessel motion under the systolic and diastolic pressure states. When the fingertip is placed on the CSRR, the periodic variation of the skin leads to a periodic resonant frequency deviation based on the perturbation theory. This frequency deviation accompanies the corresponding phase shift. By injecting this phase-shifted signal into the SO-CSRR, it generates a frequency deviation at its output. This is the frequency-modulated signal, based on the injection-locked theory. Moreover, as the SO-CSRR is locked by the phase-locked loop, the vital-sign information contained in the frequency-modulated signal can be demodulated at the tuning-voltage terminal. The proposed sensor is called a PPIL sensor on account of its sensing mechanism and demodulation technique. In this article, the proposed sensor is employed to detect the finger and wrist pulses. Both the pulse interval and the waveform shape strongly agree with the results obtained using the photoplethysmography sensor. Since the proposed sensor has the benefits of having a simple system architecture, compact circuit size, and high sensitivity, it has great potential to be developed as a wearable sensor for healthcare applications.