Resistance Values Research Articles

Механизм влияния электрического поля на процесс модифицирования серого чугуна

A diagram of an experimental installation for measuring the electrical resistance of a gray cast iron melt is presented, where a gauge based on a Kelvin double bridge is used. It is shown that the value of the specific electrical resistance of gray cast iron varies depending on the type of conditioning agent. Experimental data on the difference in specific resistivity values for various gray cast iron nucleating agents are presented. Changes in the values of electrical resistance under the influence of electric field treatment of inoculated cast iron melt are also given. Comparison of the strength values of gray cast iron with its values of the electrical resistivity of the cast iron melt after the electrical field exposure showed their simultaneous change. The decrease in the values of the electrical resistance of hot iron due to the electric field exposure is shown and it corresponds to an increment in the strength of inoculated cast iron. The effectiveness of the electric field exposure on the process of inoculation is determined by thermal ionization of the chemical elements included in the conditioning agent. The maximum increase of these parameters after electric field exposure when using FS75 nucleating agent is shown. The mechanism of the influence of an electric field on the cast iron solidification for the inoculation process of FS75, containing 75 % silicon in its composition, is described. The dependence of the efficiency of electric field exposure on the composition of the nucleating agent for gray cast iron is shown. A physical model of the effect of an electric field exposure on the process of cast iron inoculation is found. The possibility of influencing the hydrodynamic situation in the melt of gray cast iron and changing the rate of dissolution of nucleating agent particles by means of electric field exposure is given

Analysis of heating defects in extension rods of extra-high voltage direct current overhead transmission lines

This paper studies the overheating defect of an extension rod in a ± 800 kV extra-high voltage direct current overhead transmission line, and proposes various factors that affect the overheating of the extension rod. Establish an equivalent model of an extra high voltage DC transmission line based on equipotential point and line parameter analysis, and calculate the model parameters. The proposed model can also be applied to ultra-high voltage DC overhead transmission lines such as ± 500 kV, and has strong universality. Simulation experiments show that if the equivalent resistance value of the split wire side is reduced by 0.01Ω, the power loss on the extension tie rod can be increased to 380.951 W; if the equivalent resistance value of the jumper side is increased by 0.01Ω, the power loss on the extension tie rod can be increased to 273.41 W. Combined with theoretical analysis and simulation verification, it is concluded that the main factor affecting the overheating of the extension rod is the change in the resistance value on the jumper side caused by the increase in contact resistance. A systematic troubleshooting plan for related defect problems is proposed, which has important reference and guidance significance for such line fault problems.

Design, Fabrication and Testing of A Novel Thermally-Actuated Tesla Valve (TATV): A Hybrid Microvalve

Abstract A novel thermally-actuated hybrid microvalve (similar to a Tesla Valve configuration) was designed, fabricated, assembled, and tested using soft lithography-based approaches. The modified design integrates the "normally open and closed" hybrid configurations of Tesla Valves with a thermo-pneumatic (or thermal-hydraulic) actuator microfabricated in-situ that modulates the diodicity of the microvalve apparatus in the microfluidic chip. Diodicity (Di) is defined as the ratio of flow rate in the forward direction to that of the reverse direction (for a constant value of pressure drop that is imposed on a microvalve device). The results from the study successfully demonstrated the operation of an array of Tesla Valves that are normally open in forward direction and marginally closed in reverse direction at room temperature (i.e., with Di > 1, the flow resistance values were different when the inlet and outlet ports were swapped). When the microfluidic chip was heated (at steady-state conditions with a nominal temperature of ~30°C), the diodicity virtually vanished (i.e., Di ≈ 1) resulting in both reverse and forward directions being normally open (or having the same flow resistance - irrespective of the flow direction).

#673 Predictive value of insulin resistance and GFR-adjusted uricemia on all-cause mortality: the URRAH study

Abstract Background and Aims Uric acid (UA) and insulin resistance (IR) are interlinked: UA contributes to adversely affects the insulin signaling pathway, while IR predicts the development of hyperuricemia. Both UA and IR are related to metabolic syndrome, which is nowadays one of the most prevalent risk factors for mortality. In the clinical scenario, the triglyceride (TG) to high-density lipoprotein cholesterol (HDL-C) ratio has been proved to have a high correlation with IR. Lipoprotein-based markers of IR are at least as strongly associated with subclinical atherosclerosis and with newly developing atherosclerotic manifestations than Homeostasis Model Assessment of Insulin Resistance (HOMA-IR). The aim of the research was to explore the extent of interaction between IR and GFR-adjusted uricemia in determining mortality risk in a large population cohort study. Method data from 18,694 subjects were included from Uric acid Right foR heArt Healt (URRAH) database. Differences between TG/HDL-C ratio quintiles were evaluated by t-test or chi-square test. We evaluated the association between TG/HDL-C ratio and GFR-adjusted uricemia, and the development of outcomes during the follow-up study period. The primary endpoint was all-cause mortality. The Kaplan-Meier method was used to calculate the cumulative survival rate. Cox proportional hazard regression models were used to analyze the prognosis associated with IR. Results after a mean follow-up of 124 ± 64 months, there were 2,665 (14.2%) deaths for all causes. The incidence of fatal, non-fatal cardiovascular events, and all-cause mortality increased in parallel with the increase of TG/HDL-C quintiles. In both diabetic and non-diabetic patients, TG/HDL-C ratio showed a positive association with increasing of GFR-adjusted uricemia (UA/GFR ratio). TG/HDL-C ratio and GFR-adjusted uricemia significantly interact in determining all-cause mortality, even in non-diabetic patients (P < 0.0001). Subjects with higher TG/HDL-C ratio quintile had a statistically significantly higher rate of mortality than patients with lower quintiles (Fig. 1, log rank test P < 0.0001), independently by uricemia, GFR, the presence of diabetes and body mass index (BMI). Multivariate analysis showed that the TG/HDL-C ratio increase the mortality risk even after adjustment for potential confounding factors included age, diabetes, UA/GFR, BMI and statins treatment (Table 1). Conclusion For practical purposes, the easily obtainable TG/HDL-C ratio may suffice to determine the impact of insulin resistance as a risk factor. TG/HDL-C ratio interacts with GFR-adjusted uricemia in predicting mortality, even in non-diabetic patients. In conclusion, Both IR and GFR-adjusted UA levels seems to have an important predictive role on all-cause mortality, independently of age, gender, diabetes, hypertension and statins.

Wide-range resistivity characterization of semiconductors with terahertz time-domain spectroscopy

Resistivity is one of the most important characteristics in the semiconductor industry. The most common way to measure resistivity is the four-point probe method, which requires physical contact with the material under test. Terahertz time domain spectroscopy, a fast and non-destructive measurement method, is already well established in the characterization of dielectrics. In this work, we demonstrate the potential of two Drude model-based approaches to extract resistivity values from terahertz time-domain spectroscopy measurements of silicon in a wide range from about 10−3 Ωcm to 102 Ωcm. One method is an analytical approach and the other is an optimization approach. Four-point probe measurements are used as a reference. In addition, the spatial resistivity distribution is imaged by X-Y scanning of the samples to detect inhomogeneities in the doping distribution.

Analysis of Magnetotelluric Response Functions at the Cam Thuy Site, Northern Vietnam

During magnetotelluric studies in North Vietnam, an effect where the impedance phases Zxy and Zyx simultaneously left their quadrants was detected at one of the sounding sites, CTH, in the Cam Thuy District, Thanh Hoa Province. Investigation of this phenomenon has shown that it is accompanied by negative (bottom-up directed) components of the Umov–Poynting vector of electromagnetic energy flux density in the entire range of the recorded periods of magnetotelluric variations. This direction of the energy flux remains unchanged when the initial coordinate system is rotated by angles of 45° and 60°. Another characteristic feature of this phenomenon is an unusual behavior of the apparent resistivity curves: the apparent resistivity values increase starting from a period of 200 s up to a period of 104 s, and this increase occurs practically along the asymptote. The analysis of the polarization of the magnetotelluric field and the asymmetry parameter (skew angle) β of the phase tensor has shown that the section exhibits significant three-dimensional distortions as manifested by β values ranging from 20° to 90°.

Understanding the transport properties of perovskite compounds as a function of temperature, frequency and DC-bias voltage using experimental measurements and appropriate theoretical models.

The present paper provides interesting measurements and methodologies to investigate the key factors controlling the electrical response of perovskite systems. The studied system was successfully prepared using a solid-state route. The chemical analysis and the X-ray diffraction results confirm the formation of the desired perovskite phase. As a result, the DC-resistivity analysis shows that the transport properties are governed by hopping mechanisms above the transition temperature. In this case, thermal agitation allows the charge-carriers to hop across the insulating barrier in the form of grain boundaries. Then, the dominance of the grain boundary contribution is proved. AC-resistivity spectra are investigated in terms of numerous power laws (UDR, SPL and NCL). Accordingly, the decrease in the resistivity values at high frequencies is explained through hopping and tunneling processes. Indeed, it is proved that the electrical transport phenomena are governed by QMT and CBH models. The coexistence of direct (C-C) and indirect (C-A-C) interactions explains the multi-behavior of the AC-resistivity. The scaling representation displays a single muster curve describing the universal dynamic response (UDR). Thus, it reveals the universality of the electrical resistivity of the system. However, the double Schottky barrier model is used to explain the grain boundary effects. A critical frequency "νc" is detected under temperature and DC-bias voltage effects. These observations disclose, in a different way, the separate contributions of the electro-active regions of the sample in the conduction phenomenon.

Magnetic field dragging in filamentary molecular clouds

Maps of polarized dust emission of molecular clouds reveal the morphology of the magnetic field associated with star-forming regions. In particular, polarization maps of hub-filament systems show the distortion of magnetic field lines induced by gas flows onto and inside filaments. We aim to understand the relation between the curvature of magnetic field lines associated with filaments in hub-filament systems and the properties of the underlying gas flows. We consider steady-state models of gas with finite electrical resistivity flowing across a transverse magnetic field. We derive the relation between the bending of the field lines and the flow parameters represented by the Alfv\'en Mach number and the magnetic Reynolds number. We find that, on the scale of the filaments, the relevant parameter for a gas of finite electrical resistivity is the magnetic Reynolds number, and we derive the relation between the deflection angle of the field from the initial direction (assumed perpendicular to the filament) and the value of the electrical resistivity, due to either Ohmic dissipation or ambipolar diffusion. Application of this model to specific observations of polarized dust emission in filamentary clouds shows that magnetic Reynolds numbers of a few tens are required to reproduce the data. Despite significant uncertainties in the observations (the flow speed, the geometry and orientation of the filament), and the idealization of the model, the specific cases considered show that ambipolar diffusion can provide the resistivity needed to maintain a steady state flow across magnetic fields of significant strength over realistic time scales.

On-site colorimetric determination of pH in brackish water aquaculture

Purpose This study aims to describe on-site determination of pH in aquaculture using a portable colorimeter. Design/methodology/approach A basic and inexpensive portable colorimeter having light sources of different wavelength has been optimized for the determination of pH. A chromic reagent is optimized to develop colors depending on different pHs. Then, the color is measured using portable colorimeter in terms of resistance. Using the resistance to absorbance relationship, the resistance values are converted to absorbance. The performance of the developed colorimetric system is compared with commercially available colorimeter and pH meter. Eighty brackish water aquaculture samples were tested using the developed colorimetric system to check its adaptability in aquaculture farms. Findings A chromic reagent optimized in this study exhibited linear relationship with the pH changes of pH standards. Portable colorimeter having three different light sources is optimized using this chromic agent for determination of pH. Colorimeter possessing yellow light revealed more linear results than the others. The developed colorimetric system determines the pH of aquaculture water with an accuracy of ±0.14 in comparison with commercial colorimeter at the pH range of 6.0−9.0. Originality/value pH plays a pivotal role in aquaculture, impacting not only productivity but also profitability. The colorimetric system introduced in this research is promising for pH measurement in the field of brackish water aquaculture. The on-site pH assessment facilitated by this colorimetric system holds significant potential for adoption within the aquaculture sector, owing to its precision, portability, simplicity of use and user-friendly nature.

Low-cost sensor-based damage localization for large-area monitoring of FRP composites

Abstract In recent years, there has been growing interest in self-sensing structural materials across research and industry sectors. Detecting and locating structural damage typically requires numerous sensors wired to a data acquisition (DAQ) circuit, rendering implementation impractical in real structures. This paper proposes an innovative, cost-effective sensor network for damage detection and localization in fiber-reinforced polymer composites. The innovation encompasses three key elements: (1) utilizing carbon fiber tows within the composite as piezoresistive sensors, eliminating the need for additional foreign sensor devices; (2) introducing a novel sensor layout wherein sensor tow branches with varied resistance values are connected in parallel, reducing the number of connections to the DAQ circuit and cutting manufacturing costs significantly; (3) developing a practical sensor terminal fabrication technique to minimize manufacturing expenses. The proposed design methodology for the branch resistance values is first validated using a demonstration panel. Subsequently, the overall strategy is assessed by conducting impact tests on carbon and glass fiber-reinforced composite specimens. Results validate the sensor’s ability to accurately detect and locate structural damage.

Fracture resistance of additively or subtractively manufactured resin-based definitive crowns: Effect of restorative material, resin cement, and cyclic loading

ObjectiveTo evaluate how restorative material, resin cement, and cyclic loading affect the fracture resistance of resin-based crowns fabricated by using additive or subtractive manufacturing. MethodsA right first molar crown standard tessellation language (STL) file was used to fabricate 120 crowns from one subtractively manufactured polymer-infiltrated ceramic network (SM) and two additively manufactured resin composites (AM-B and AM-S) (N = 40). These crowns were randomly divided into 4 groups within each material according to the dual-polymerizing resin cement to be used (RX and PN) and the aging condition (n = 10). After cementation, the crowns without cyclic loading were subjected to fracture testing, while the others were first cyclically loaded (1.7 Hz, 1.2 million cycles, and 49-N load) and then subjected to fracture testing. Data were analyzed with generalized linear model analysis (α = .05). ResultsFracture resistance of the crowns was affected by material, resin cement, and cyclic loading (P ≤ .030). However, none of the interactions significantly affected fracture resistance of tested crowns (P ≥ .140). Among tested materials, SM had the highest fracture resistance, whereas AM-B had the lowest (P ≤ .025). RX led to higher fracture resistance, and cyclic loading decreased the fracture resistance (P ≤ .026). SignificanceTested materials can be considered reliable in terms of fracture resistance in short- or mid-term (5 years of intraoral simulation) when used for single molar crowns with 2 mm occlusal thickness. In the long term, polymer-infiltrated ceramic network crowns cemented with RelyX Universal may provide promising results and be less prone to complications considering higher fracture resistance values obtained.

Continuous estimation of respiratory system compliance and airway resistance during pressure-controlled ventilation without end-inspiration occlusion

BackgroundAssessing mechanical properties of the respiratory system (Cst) during mechanical ventilation necessitates an end-inspiration flow of zero, which requires an end-inspiratory occlusion maneuver. This lung model study aimed to observe the effect of airflow obstruction on the accuracy of respiratory mechanical properties during pressure-controlled ventilation (PCV) by analyzing dynamic signals.MethodsA Hamilton C3 ventilator was attached to a lung simulator that mimics lung mechanics in healthy, acute respiratory distress syndrome (ARDS) and chronic obstructive pulmonary disease (COPD) models. PCV and volume-controlled ventilation (VCV) were applied with tidal volume (VT) values of 5.0, 7.0, and 10.0 ml/kg. Performance characteristics and respiratory mechanics were assessed and were calibrated by virtual extrapolation using expiratory time constant (RCexp).ResultsDuring PCV ventilation, drive pressure (DP) was significantly increased in the ARDS model. Peak inspiratory flow (PIF) and peak expiratory flow (PEF) gradually declined with increasing severity of airflow obstruction, while DP, end-inspiration flow (EIF), and inspiratory cycling ratio (EIF/PIF%) increased. Similar estimated values of Crs and airway resistance (Raw) during PCV and VCV ventilation were obtained in healthy adult and mild obstructive models, and the calculated errors did not exceed 5%. An underestimation of Crs and an overestimation of Raw were observed in the severe obstruction model.ConclusionUsing the modified dynamic signal analysis approach, respiratory system properties (Crs and Raw) could be accurately estimated in patients with non-severe airflow obstruction in the PCV mode.

Association between being large for gestational age and cardiovascular metabolic health in children conceived from assisted reproductive technology: a prospective cohort study.

To the best of our knowledge, no study has investigated the potential joint effect of large for gestational age (LGA) and assisted reproductive technology (ART) on the long-term health of children. This was a prospective cohort study that recruited children whose parents had received ART treatment in the Center for Reproductive Medicine, Shandong Provincial Hospital, affiliated to Shandong University, between January 2006 and December 2017. Linear mixed model was used to compare the main outcomes. The mediation model was used to evaluate the intermediary effect of body mass index (BMI). 4138 (29.5%) children born LGA and 9910 (70.5%) children born appropriate for gestational age (AGA) were included in the present study. The offspring ranged from 0.4 to 9.9years. LGAs conceived through ART were shown to have higher BMI, blood pressure, fasting blood glucose, fasting insulin, and homeostatic model assessment of insulin resistance values, even after controlling for all covariates. The odds of overweight and insulin resistance are also higher in LGA subjects. After adjusting for all covariates, LGAs conceived through ART had BMI and BMI z-scores that were 0.48kg/m2 and 0.34 units greater than those of AGAs, respectively. The effect of LGA on BMI was identified as early as infancy and remained consistently significant throughout pre-puberty. Compared to AGA, LGA children conceived from ART were associated with increased cardiovascular-metabolic events, which appeared as early as infancy and with no recovery by pre-puberty.

Delineation of aquifer storage potential in response to regional groundwater development

Developing aquifers as part of sustainability efforts toward groundwater development is a tactical approach to meeting water demand and management objectives. Delineation of aquifer storage potential (ASP) and longitudinal conductance (SL\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{L}$$\\end{document}) is a good approach to protect and manage groundwater resources. A Schlumberger configuration was applied to delineate fifteen (15) vertical electrical sounding (VES) stations alongside a 2D electrical resistivity imagery (ERI) profile and regional borehole data to characterize the regional ASP. The results of the study show that the layer resistivity and thickness values of the regional aquifer unit range from 39.9–105 Ωm and 15–44 m, respectively, while the overburden thickness overlays the regional aquifer unit varied between 5–10 m corresponding to the regional borehole data. The weathered/fractured basemen, which constitute the regional aquifer unit were delineated, which consists of shallow, moderate, and deep aquifer zones. The deep aquifer zones fall within the depth of 30–44 m and are considered suitable for groundwater prospective. The weathered layer with appreciably low resistivity values with thick aquifer regolith has also been identified as most suitable for borehole siting. The weathered/fractured encountered within thick aquifer regolith were mapped as the region with a high ASP for groundwater development. In addition, the values of longitudinal conductance, SL\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{L}$$\\end{document} and transverse resistance, RT\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${R}_{T}$$\\end{document} estimated from aquifer parameters vary between 0.21-0.85Ω-1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$0.21-0.85 \\,{\\Omega }^{-1}$$\\end{document} and 1695-3124Ωm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$1695-3124\\, {\\Omega m}^{2}$$\\end{document}, respectively. The SL\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{L}$$\\end{document} values show that the study area falls within moderate (0.20-0.69Ω-1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$0.20-0.69 \\,{\\Omega }^{-1}$$\\end{document}) and good (0.7-4.9Ω-1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$0.7-4.9 \\,{\\Omega }^{-1}$$\\end{document}), which invariably determined the regional aquifer protective capacity. Thus, the DC geoelectrical approach has been successfully employed in a lateritic-based environment to delineate aquifer-promising zones for regional groundwater development.

Interfacial thermal resistance between mechanically exfoliated nm-thick MoS2 and silicon from −60 °C to 50 °C based on ns-ET Raman technique

In the miniaturization and integration development of micro-devices, the large thermal contact resistance significantly affects the overall performance of micro-devices, which is influenced by both interfacial contact condition and material properties. However, the temperature dependence of interfacial thermal resistance of realistic materials remains unclear. In this work, the interfacial thermal resistance between nm-thick MoS2 nanosheets and Si substrate is measured by using the ns energy transport state-resolved Raman (ns ET-Raman) technique. By comparing the experimental data with finite difference numerical simulation, the real value of the interfacial thermal resistance is determined. By changing the ambient temperature from -60 °C to 50 °C, the interfacial thermal resistance against temperature curve is obtained. As the environmental temperature deviates from room temperature, a large increasement of the interfacial thermal resistance can be observed. As temperature goes back to room temperature, the unreversible interfacial thermal resistance indicates that the large thermal expansion mismatch deteriorates the contact situation. In the last, the interfacial thermal resistance evolution under varying environmental temperatures from both experiments and modeling results in literatures are compared and discussed to illustrate the effect of different interface formation methods. For epitaxial and CVD grown materials, the interfacial thermal resistance generally reduces with raising ambient temperature. While for mechanically exfoliated samples, the effect of thermal expansion mismatch and the resulting gaps dominate the interfacial thermal resistance, which leads to non-monotonous temperature dependency with a valley located at room temperature.

A Comprehensive Review of Reactive Flame Retardants for Polyurethane Materials: Current Development and Future Opportunities in an Environmentally Friendly Direction.

Polyurethanes are among the most significant types of polymers in development; these materials are used to produce construction products intended for work in various conditions. Nowadays, it is important to develop methods for fire load reduction by using new kinds of additives or monomers containing elements responsible for materials' fire resistance. Currently, additive antipyrines or reactive flame retardants can be used during polyurethane material processing. The use of additives usually leads to the migration or volatilization of the additive to the surface of the material, which causes the loss of the resistance and aesthetic values of the product. Reactive flame retardants form compounds containing special functional groups that can be chemically bonded with monomers during polymerization, which can prevent volatilization or migration to the surface of the material. In this study, reactive flame retardants are compared. Their impacts on polyurethane flame retardancy, combustion mechanism, and environment are described.

Comparison of ePTFE membranes with fluorine-free alternatives considering durability of laminated fabrics using hydrostatic pressure testing

Pleasant wearing comfort is achieved using laminated fabrics containing a waterproof and breathable membrane. The most used membrane type is expanded polytetrafluoroethylene. Due to the negative impact of perfluoroalkyl and polyfluoroalkyl substances on the environment, fluorine-free alternative materials are necessary. In this work, alternative membrane materials, polyurethane and polyethylene terephthalate, were compared with expanded polytetrafluoroethylene. First, the mass per unit area, thickness, tensile properties, water vapor resistance, and hydrostatic pressure of corresponding laminates were determined. Furthermore, their durability, which is an essential aspect of sustainability, was investigated. Therefore, they were hydrolyzed, weathered, washed, and incorrectly treated (e.g. washed with fabric softener) and then investigated for hydrostatic pressure resistance, by scanning electron microscopy, infrared spectroscopy, and digital microscopy. It was shown that polyethylene terephthalate and expanded polytetrafluoroethylene are comparable with respect to breathability, waterproofness (>20 bar), and durability. However, the hydrostatic pressure resistance (approximately 11 bar) and the water vapor resistance values (>23 m2 · Pa · W−1) of microporous polyurethane membranes are poorer, but they still provide suitable alternatives. In addition, a beginning degradation of polyurethane could be proved after hydrolysis and weathering. Furthermore, the deposition of calcium salts on all membranes was observed after washing with tap water, fabric softener, and washing agents.

On the frequency dependence of the PDIV in twisted pair magnet wire analogy in humid air

The partial discharge inception voltage (PDIV) of low-voltage induction motor turn-turn insulation analogy is investigated for variable relative humidity (RH) of the surrounding air (temperature and pressure are kept constant close to their ambient values). Three materials, perfluoralkoxy alkane, sealed and unsealed alumina (UA), are employed as the dielectric coating (insulation) of test samples. Each material’s dielectric properties change differently with RH—of these, relative permittivity is regarded as the most crucial, as it was previously proven to be, along with the coating’s thickness, the key factor in determining the PDIV in dry air conditions. To further vary the value of permittivity and thus provide larger data sets for the verification study, the frequency of the excitation voltage is also varied between 1 Hz and 50 kHz. The obtained experimental data are compared against the PDIV predictions obtained by a breakdown model based on the reduced thickness of the coating (ratio of the coating thickness to its relative permittivity). Satisfying agreement between the measured and predicted PDIV are obtained for the first two materials, whereas significant discrepancies are seen for the UA material. For this case, surface conductivity is introduced into the prediction model and much better fits to the experimental data are obtained for a suitable value of surface resistance. It is hence demonstrated that the model is able to satisfactorily predict the PDIV for three substantially different materials when the RH of the surrounding air is varied between 10% – 80% .

Propagation Mechanism and Suppression Strategy of DC Faults in AC/DC Hybrid Microgrid

Due to their efficient renewable energy consumption performance, AC/DC hybrid microgrids have become an important development form for future power grids. However, the fault response will be more complex due to the interconnected structure of AC/DC hybrid microgrids, which may have a serious influence on the safe operation of the system. Based on an AC/DC hybrid microgrid with an integrated bidirectional power converter, research on the interaction impact of faults was carried out with the purpose of enhancing the safe operation capability of the microgrid. The typical fault types of the DC sub-grid were selected to analyze the transient processes of fault circuits. Then, AC current expressions under the consideration of system interconnection structure were derived and, on this basis, we obtained the response results of non-fault subnets under the fault process, in order to reveal the mechanism of DC fault propagation. Subsequently, a current limitation control strategy based on virtual impedance control is proposed to address the rapid increase in the DC fault current. On the basis of constant DC voltage control in AC/DC hybrid microgrids, a virtual impedance control link was added. The proposed control strategy only needs to activate the control based on the change rate of the DC current, without additional fault detection systems. During normal operations, virtual impedance has a relatively small impact on the steady-state characteristics of the system. In the case of a fault, the virtual impedance resistance value is automatically adjusted to limit the change rate and amplitude of the fault current. Finally, a DC fault model of the AC/DC hybrid microgrid was built on the RTDS platform. The simulation and experimental results show that the control strategy proposed in this paper can reduce the instantaneous change rate of the fault state current from 19.1 kA/s to 2.73 kA/s, and the error between the calculated results of equivalent modeling and simulation results was within 5%. The obtained results verify the accuracy of the mathematical equivalent model and the effectiveness of the proposed current limitation control strategy.

Анализ влияния местных сопротивлений горных выработок на общешахтное аэродинамическое сопротивление

This paper aims to provide a quantitative assessment of the effect of local aerodynamic resistance on total mine airflow resistance with account for the friction resistance. The research includes laboratory tests, computer simulations in the Ansys CFD software as well as analytical inferences. The performed studies specified the magnitudes of local resistances at the turnings of mine workings. It has been established that the value of local resistance in all the sections can exceed 10% of the total mine aerodynamic friction resistance. This depends on the geometric parameters of the mine workings, which may result in a significant increase in the ratio of the local resistance value to the aerodynamic friction resistance value. The correlation of the two coefficients, i.e. the friction coefficient and the coefficient of local resistances, are proved to have a significant impact. The sharper the turns of the mine workings are, the greater the ratio of the local resistance to the aerodynamic friction resistance value is. Therefore, it is necessary to take this type of resistance into account when designing mine ventilation systems.