Release Of Flavor Compounds Research Articles

Impact of thermal processing and emulsification methods on spice oleoresin blending: Insights for flavor release and emulsion stability

This study investigated the effect of heat treatments on the pungency and aroma profiles of a spice oleoresin blend, and the emulsion stability with different surfactants, encapsulating agents, and homogenization mechanisms. Total pungency increased with heat until 120 °C and drastically reduced at 150 °C. Thermal processing induced aroma release, and 46 compounds were identified at 90 °C, predominantly comprising sesquiterpenes. Tween 80 dispersed the highest oleoresin mass (6.21 ± 0.31 mg/mL) and reported the maximum emulsion stability index. The oleoresin percentage significantly influenced the emulsion stability, with 1% oleoresin producing the most stable emulsion. High-pressure homogenization applied on gum Arabic resulted in a greater encapsulation efficiency, exceeding 86%, and the lowest creaming index (4.70 ± 0.06%), while Hi-Cap 100 produced the best flow properties. The findings provide insights into incorporating lipophilic spice oleoresin blends in aqueous food systems and understanding the release of flavor compounds during thermal food processing.

Effects of combined drying techniques and cellulase hydrolysis on the nutritional value and sensory properties of shiitake mushrooms (Lentinus edodes)

Dried shiitake mushrooms offer rich nutritional value and unique sensory properties, prompting further investigation. The effects of different drying techniques (hot air drying (HAD), infrared hot air drying (IRHAD), pulsed vacuum drying (PVD), vacuum freeze drying (VFD), and natural drying (ND)) combined with enzymatic hydrolysis on the release of flavor compounds and nutrients from shiitake mushrooms were explored. The combination of HAD with cellulase hydrolysis yielded notably high levels of umami amino acids (5.4723 ± 0.1501 mg/g) and 5′-nucleotides (4.0536 ± 0.0062 mg/g), and superior volatile flavors. Combined with cellulase hydrolysis, IRHAD achieved the highest level of total sugars (6.57 ± 0.34 mg/mL), VFD resulted in the greatest soluble protein content (153.21 ± 0.23 μg/mL), PVD yielded the highest total phenolics content (93.20 ± 0.41 μg GAE/mL), and ND produced the maximum reducing sugar content (5.79 ± 0.13 mg/mL). This study addresses crucial gap in the post-drying processing of shiitake mushrooms, offering valuable insights for further product development of shiitake mushrooms.

Comprehensive Multi-Spectroscopy and Molecular Docking Understanding of Interactions between Fermentation-Stinky Compounds and Mandarin Fish Myofibrillar Proteins.

The release of flavor compounds is a critical factor that influences the quality of fermented foods. A recent study investigated the interactions between four fermentation-stinky compounds (indole, isovaleric acid, dimethyl disulfide, and dibutyl phthalate) and myofibrillar proteins (MPs). The results indicated that all four fermentation-stinky compounds had different degrees of binding to MPs, with dibutyl phthalate and dimethyl disulfide exhibiting stronger interactions. Reduced hydrophobicity enhanced these interactions. Multi-spectroscopy showed that static fluorescence quenching was dominant in the MPs-fermentation-stinky compound complexes. The interaction altered the secondary structure of MPs, predominantly transitioning from β-sheets to α-helix or random coil structures via hydrogen bond interactions. Molecular docking confirmed that these complexes maintained steady states due to stronger hydrogen bonds, van der Waals forces, ionic bonds, conjugate systems, and lower hydrophobicity interactions. Hence, it is a novel sight that the addition of hydrophobic bond-disrupting agents could improve the flavor of fermented foods.

Multiple Technologies Combined to Analyze the Changes of Odor and Taste in Daokou Braised Chicken during Processing.

This study analyzed the changes of odor and taste in Daokou braised chicken during processing by GC-MS, GC-IMS, e-nose and e-tongue. The 75 and 55 volatile compounds identified in Daokou braised chicken by GC-MS and GC-IMS, respectively, included hydrocarbons, aldehydes, alcohols, terpenes, ketones, heterocyclics, esters, acids and phenols; among them, aldehydes, alcohols and ketones were the most abundant. The number and proportion of volatile compounds in Daokou braised chicken changed significantly (p < 0.05) in the process. The proportion of volatile compounds with animal fatty odor, such as aldehydes and alcohols, decreased, while that of esters, ketones and terpenes from spices with fruity fragrance increased, especially in the braising stage. An e-nose showed that the odor intensities of sulfur-containing and nitrogen oxide compounds were higher (p < 0.05) after the braising stage, but weakened after 2 h braising. An e-tongue showed that saltiness and richness increased significantly (p < 0.05) after braising. The results of these four techniques showed that braising promoted the release of flavor compounds, and was beneficial to salt penetration and umami release. However, long braising could lead to weakened flavor intensity and the introduction of bitterness and astringency. This study also found that GC-IMS and e-nose were more sensitive to trace compounds such as sulfur-containing and nitrogen oxide compounds, esters, acids and phenolics in Daokou braised chicken than GC-MS. The use of multiple technologies could provide more comprehensive flavor profiles for Daokou braised chicken during processing. This study provides insights into the control of flavor of Daokou braised chicken, and may be of practical relevance for the poultry industry.

Effects of soybean phospholipids, ovalbumin, and starch sodium octenyl succinate on the mechanical, microstructural, and flavor properties of emulsified surimi gels

Liquid oils are frequently used to improve texture, enhance color, and as processing aids to improve the quality of emulsified surimi products and address the lack of essential nutrients in raw surimi seafoods. To clarify the role of interactions between oil droplet and myofibrillar proteins of surimi-based products in determining the mechanical and microstructural properties of emulsified surimi gels, we investigated the effects of emulsifiers (ovalbumin (OVA), soybean phospholipids (SP), and starch sodium octenyl succinate (SSOS)) on the mechanical, microstructural, and flavor properties of emulsified surimi gels. The emulsion droplets in the SP-containing gel led to a significant decrease in the hardness, gel strength, and viscoelasticity, and experienced flocculation and were inhomogeneously distributed in the gel matrix. Conversely, OVA- and SSOS-containing gels exhibited elevated hardness, gel strength, and viscoelasticity, and featured homogeneously distributed emulsion droplets. The introduction of SP caused darkening, whereas that of OVA and SSOS resulted in enhanced gel whiteness. Finally, the release of flavor compounds from the gel matrix was faster for SP-containing gels than that for OVA- and SSOS-containing gels, which was attributed to the different gel structures. Thus, the introduction of additional emulsifiers facilitated the fabrication of emulsified surimi gels with tailor-made structures.

Encapsulation of Fruit Flavor Compounds through Interaction with Polysaccharides.

Production and storage, the influence of packaging materials and the presence of other ingredients in fruit products can cause changes in flavor compounds or even their loss. Due to these issues, there is a need to encapsulate flavor compounds, and polysaccharides are often used as efficient carriers. In order to achieve effective encapsulation, satisfactory retention and/or controlled release of flavor compounds, it is necessary to understand the nature of the coated and coating materials. Interactions that occur between these compounds are mostly non-covalent interactions (hydrogen bonds, hydrophobic interactions and van der Waals forces); additionally, the formation of the inclusion complexes of flavor compounds and polysaccharides can also occur. This review provides insight into studies about the encapsulation of flavor compounds, as well as basic characteristics of encapsulation such as the choice of coating material, the effect of various factors on the encapsulation efficiency and an explanation of the nature of binding.

The Relationship Between Salivary Redox, Diet, and Food Flavor Perception.

The mouth is the gateway for entrance of food and microorganisms into the organism. The oral cavity is bathed by saliva, which is thus the first fluid that food and microorganisms will face after their entrance. As a result, saliva plays different functions, including lubrication, predigestion, protection, detoxification, and even transport of taste compounds to chemoreceptors located in the taste buds. To ensure its function of protection, saliva contains reactive harmful compounds such as reactive oxygen species that are controlled and neutralized by the antioxidant activity of saliva. Several antioxidant molecules control the production of molecules such as reactive oxygen compounds, neutralize them and/or repair the damage they have caused. Therefore, a balance between reactive oxidant species and antioxidant compounds exists. At the same time, food can also contain antioxidant compounds, which can participate in the equilibrium of this balance. Numerous studies have investigated the effects of different food components on the antioxidant capacity of saliva that correspond to the ability of saliva to neutralize reactive oxygen species. Contradictory results have sometimes been obtained. Moreover, some antioxidant compounds are also cofactors of enzymatic reactions that affect flavor compounds. Recent studies have considered the salivary antioxidant capacity to explain the release of flavor compounds ex vivo or in vivo. This article aims to review the effect of food on the antioxidant capacity of saliva and the impact of salivary antioxidant capacity on flavor perception after a brief presentation of the different molecules involved.

Orthonasal and retronasal detection thresholds of 26 aroma compounds in a model alcohol-free beer: Effect of threshold calculation method.

Detection thresholds are used routinely to determine the odour-active compounds in foods. The composition of a food matrix, such as hydrophobicity or solids content, has an impact on the release of flavour compounds, and thus on thresholds. In the case of beer, thresholds determined in alcoholic beer may not be the same for alcohol-free beer (AFB). Therefore, the aim of this study was to determine detection thresholds for aroma compounds typically found in beer, within a model AFB. The model was designed to match the sugar concentration and pH of an AFB brewed by a cold contact process. Thresholds were measured using a 3-AFC procedure and calculated using either Best Estimate Threshold (BET) method or by logistic regression. Moreover, an algorithm for the removal of false positives was applied to adjust the assessors' raw responses. Retronasal thresholds were generally lower than orthonasal. Those calculated by BET were significantly higher (p < 0.05) than those from logistic regression, and removal of false positives also produced significantly higher thresholds than those from raw data. The use of logistic regression has the advantage of providing the mathematical model describing the behaviour of the group. The results from this study can be used to better understand the role of flavour compounds in AFB and the effect of the calculation method to prevent under- or overestimated results.

Submaxillary Mucin: its Effect on Aroma Release from Acidic Drinks and New Insight into the Effect of Aroma Compounds on its Macromolecular Integrity

Submaxillary mucin is a major component that defines the makeup and functionality of saliva. Understanding its structure and function during food intake is key to designing appropriate strategies for enhancing the delivery of flavour. In the present study, the hydrodynamic integrity of bovine submaxillary mucin was characterised under physiological and acidic conditions and it was shown to have a broad molecular weight distribution with species ranging from 100 kDa to over 2000 kDa, and a random coil type of conformation. A decrease in the pH of mucin appeared to result in aggregation and a broader molecular weight distribution, which was shown to correlate with a release of flavour compounds. Our study also provides indications that p-cresol may have an effect on the macromolecular integrity of mucin.

Kinetic study of controlled release of flavor compounds from spray-dried encapsulated yeast powder using dynamic vapor sorption-gas chromatography.

The release profile of d-limonene and ethyl hexanoate was investigated using a dynamic vapor sorption (DVS) system coupled with gas chromatography. The flavors were encapsulated by spray drying using Saccharomyces cerevisiae cells from which β-glucan had been partially extracted. Relative humidity (RH) was stepped from 20% to 50, 60, 70, and 80% at 30, 40, 50, and 60ºC. The maximum release flux for d-limonene and ethyl hexanoate was around 12 and 28mg/s∙m2∙g-powder at 80% RH and 60ºC incubation. The Weibull distribution function was well fitted with the experimental data to analyze release kinetics. The release mechanism parameter was greater than 1.0, which indicates a controlled release with initial induction time. The activation energy for ethyl hexanoate (6 kJ/mol) was lower than d-limonene (41kJ/mol) at 80% RH, which indicates higher affinition of ethyl hexanoate to migrate from the lipid bilayer membrane towards the water phase.

Effects of water absorption of soybean seed on the quality of soymilk and the release of flavor compounds.

The water absorption of soybeans during soaking is directly related to the quality characteristics and the flavor properties of soybeans for processing. In this paper, the effects of water absorption of soybean seed on the quality of soymilk and the release of flavor compounds were investigated during soaking at 4 °C, 25 °C, and 50 °C at different pH values. The results showed that the water absorption rate increased as the soaking temperature and pH increased, while the equilibrium value was relatively stable. Peleg's equation with good fitting of the absorption kinetics was used to predict the hydration characteristics of undehulled soybean. MALDI-TOF/TOF-MS results showed that the major released proteins are basic 7S globulin, which is released in large amounts at high temperature. The water absorption of soybean seed significantly enhanced the extraction yields of protein, fat and solids of the prepared soymilk, and alkaline soaking pH further promoted the extraction of proteins and solids. A high soaking temperature can significantly decrease the required soaking time; however, it is unfavorable to the extraction yields of fat, proteins and solids, as well as the whiteness values and the particle sizes. The beany odor compounds of soymilk mainly consisted of hexanal, trans-2-hexenal, 1-octene-3-ol, hexanol, and 2-pentylfuran, and their contents were positively correlated with soaking temperature. A good balance of soymilk quality and flavor compound release can be achieved with soaking conditions of 25 °C and pH 9.

Release of Flavor Compounds from Micelles and O/W Emulsions

Release of Flavor Compounds from Micelles and O/W Emulsions

Effect of xanthan gum on the release of strawberry flavor in formulated soy beverage

The effects of xanthan gum on the release of strawberry flavor compounds in formulated soy protein isolate (SPI) beverage were investigated by headspace gas chromatography (GC). Seven strawberry flavor compounds (limonene, ethyl hexanoate, (Z)-3-hexenyl acetate, ethyl 2-methylbutanoate, ethyl butanoate, (Z)-3-hexen-1-ol and diacetyl) could be detected by GC and hence analyzed the gas-matrix partition coefficients (K). The release of flavor compounds was restrained in SPI and/or xanthan gum solution. The retention of (Z)-3-hexen-1-ol, limonene and diacetyl significantly changed (p<0.05) with increasing xanthan gum concentrations. Presence of any other esters led to suppression of the release of ester compounds in water and SPI solution. The less-volatiles (γ-decalactone, methyl cinnamate, hexanoic acid, 2-methyl butyric acid and furaneol) accelerated the release of ester compounds to some extent in different matrices. The above results demonstrated that presence of SPI and xanthan gum could bring about an imbalance in the strawberry flavor.

Transcriptome analysis of Lactococcus lactis subsp. lactis during milk acidification as affected by dissolved oxygen and the redox potential

Performance of Lactococcus lactis as a starter culture in dairy fermentations depends on the levels of dissolved oxygen and the redox state of milk. In this study the microarray analysis was used to investigate the global gene expression of L. lactis subsp. lactis DSM20481T during milk acidification as affected by oxygen depletion and the decrease of redox potential. Fermentations were carried out at different initial levels of dissolved oxygen (dO2) obtained by milk sparging with oxygen (high dO2, 63%) or nitrogen (low dO2, 6%). Bacterial exposure to high initial oxygen resulted in overexpression of genes involved in detoxification of reactive oxygen species (ROS), oxidation–reduction processes, biosynthesis of trehalose and down-regulation of genes involved in purine nucleotide biosynthesis, indicating that several factors, among them trehalose and GTP, were implicated in bacterial adaptation to oxidative stress. Generally, transcriptional changes were more pronounced during fermentation of oxygen sparged milk. Genes up-regulated in response to oxygen depletion were implicated in biosynthesis and transport of pyrimidine nucleotides, branched chain amino acids and in arginine catabolic pathways; whereas genes involved in salvage of nucleotides and cysteine pathways were repressed. Expression pattern of genes involved in pyruvate metabolism indicated shifts towards mixed acid fermentation after oxygen depletion with production of specific end-products, depending on milk treatment. Differential expression of genes, involved in amino acid and pyruvate pathways, suggested that initial oxygen might influence the release of flavor compounds and, thereby, flavor development in dairy fermentations. The knowledge of molecular responses involved in adaptation of L. lactis to the shifts of redox state and pH during milk fermentations is important for the dairy industry to ensure better control of cheese production.

The effect of prime emulsion components as a function of equilibrium headspace concentration of soursop flavor compounds.

BackgroundPerceptions of food products start when flavor compounds are released from foods, transported and appropriate senses in the oral and nose are triggered. However, the long-term stability of flavor compounds in food product has been a major concern in the food industry due to the complex interactions between key food ingredients (e.g., polysaccharides and proteins). Hence, this study was conducted to formulate emulsion-based beverage using natural food emulsifiers and to understand the interactions between emulsion compositions and flavor compounds.ResultsThe influences of modified starch (x 1 ), whey protein isolate (x 2 ), soursop flavor oil (x 3 ) and deionized water (x 4 ) on the equilibrium headspace concentration of soursop volatile flavor compounds were evaluated using a four-component with constrained extreme vertices mixture design. The results indicated that the equilibrium headspace concentration of soursop flavor compounds were significantly (p < 0.05) influenced by the matrix and structural compositions of the beverage emulsions. Interface formed using modified starch and whey protein isolate (WPI) proved to be capable of inhibiting the release of volatile flavor compounds from the oil to the aqueous phase. Modified starch could retard the overall flavor release through its hydrophobic interactions with volatile flavor compounds and viscosity enhancement effect. Excessive amount of modified starch was also shown to be detrimental to the stability of emulsion system. However, both modified starch and WPI showed to be a much more effective barrier in inhibiting the flavor release of flavor compounds when used as individual emulsifier than as a mixture.ConclusionsOverall, the mixture design can be practical in elucidating the complex interactions between key food components and volatile flavor compounds in an emulsion system. These studies will be useful for the manufacturers for the formulation of an optimum beverage emulsion with desirable emulsion properties and desirable flavor release profile.

Wickerhamomyces anomalus AS1: a new strain with potential to improve wine aroma

The monoterpenes are the most important contribution to the olfactory profile of wine due to their low odour threshold. These and other aroma-active substances do not generally exist in a free form but are conjugated to mono- or disaccharides, thereby forming water-soluble and odourless complexes. Enzymes that cleave the sugar moieties from the precursors can, therefore, have a major impact on the sensory profile of wine, as they release the volatile aroma compounds. For this reason, we searched for wine yeasts producing glycosidases which are active under oenological conditions. A collection of 100 wine yeasts were screened for glycosidase activities in whole cells and in culture supernatants. Kinetic parameters were determined spectrophotometrically with synthetic model substrates, and hydrolysis of natural glycosides was detected by thin-layer chromatography. A yeast isolate, AS1, was identified as a new Wickerhamomyces anomalus strain which hydrolysed a number of synthetic and natural glycosides under oenological conditions. Citronellol- and nerol-glucosides, among the most frequently occurring aroma precursors in wine, were also cleaved. In contrast to a commercial β-glucosidase, whole cells of W. anomalus AS1 catalysed deglycosylation of arbutin and salicin directly in a white and a red wine. Besides the formation of intra- and extracellular glucoside hydrolases, strain AS1 exhibited arabinosidase and xylosidase activities which are also essential for the release of flavour compounds. Even with limited functionality at oenological conditions, the glycoside hydrolase activities of W. anomalus AS1 may improve aroma development, provided that the reaction occurs over a longer period, as it is the case during wine-making.

Characterising the release of flavour compounds from chewing gum through HS-SPME analysis and mathematical modelling

The headspace solid-phase microextraction (HS-SPME) technique combined with GC–MS was evaluated to study 33 selected flavour compounds released from chewing gum. The operating conditions of SPME were optimised, including different fibres (PDMS, DVB/CAR/PDMS, PA and PDMS/DVB), sample size, extraction time and temperature. The results indicated that while HS-SPME was a rapid and valuable technique, poor reproducibility occurred under all conditions. It was found that this deficiency could be alleviated by utilising mathematical modelling techniques, an approach which had not been previously used in the analysis of flavour compounds in chewing gum by HS-SPME. Compared to the instrumental analysis data themselves, the models provided more insights to the release behaviour of flavour compounds from chewing gum and the more reproducible kinetic rate constants might be used for comparing the release of different compounds or the same compound under different conditions.

Release and Evaporation of Volatiles during Boiling of Unhopped Wort

The release and evaporation of volatile compounds was studied during boiling of wort. The observed parameters were boiling time, boiling intensity, wort pH, and wort density. The effect of every parameter was discussed and approached chemically, with an eye on beer-aging processes. The results indicated that pH highly influenced the release of flavor compounds and that the formation of Strecker aldehydes was linear with boiling time. However, because of evaporation of volatiles, information about the applied thermal load on wort is lost when using a volatile heat load indicator. The thiobarbituric acid (TBA) method, which includes the nonvolatile precursors of volatile aging compounds, proved to be a more reliable method to determine all kinds of heat load on wort. Finally, it was discussed how the obtained insights could help to understand the mechanism of beer aging.

Ingredientes usados na indústria de chocolates

Chocolate is a product widely consumed throughout the world that has seen generally increasing production trends over the last years. Making chocolate requires an understanding of how the consumer perceives it. The preferred type of chocolate varies from country to country. The different tastes and uses for chocolate reflect the histories of the industry in different places. The taste of chocolate is partially determined by the chemistry of the product. Taste depends on the release of flavor compounds in the mouth and nose, while perceived texture is a function of the way in which the material melts and breaks up in the mouth. Most chocolates that are available on the market throughout the world are made from very similar ingredients, yet have very different flavors. Some manufacturers have specific house flavors, and very often this is due to specific changes during the manufacturing process, where changes in holding times, acidity and temperature can give rise to very different flavors in the final chocolate. For this reason, chocolate manufacturing conditions are often kept a closely guarded secret. The ingredients used in chocolate and confectionery products have an important role in consumers acceptance and presentation of the product.

Investigation of the retronasal flavour release during the consumption of coffee with additions of milk constituents by ‘Oral Breath Sampling’

The aim of this study was the investigation of the influence of milk proteins (casein and whey proteins) and milk fat on the release of flavour compounds from white coffee beverages in the oral cavity. For this reason a retronasal headspace technique for measurement of the after-flavour was adapted. A ‘Gas Sampler’ equipped with a mouthpiece was used as an ‘Oral Breath Sampler (OBS)’. Analyses were performed by gas chromatography with mass spectrometric detection. It was noticed that the sampling at different hours resulted in different standard deviations. The flavour release is more constant in the morning (Variation coefficient from 3% to 28%; median: 10%) than in the afternoon (7–52%; median: 23%). The relationships between flavour release and some salivary parameters like salivation rate, buffer capability and protein content were also studied. The ‘Oral Breath Sampling’ was considered to be a valuable sampling method for the analysis of the retronasal aroma release from coffee beverages.