Reflected Laser Light Research Articles

Light Reflections Detection And Correction For Robotic Volumetric PIV

Laser light reflection mitigation in Particle Image Velocimetry (PIV) is crucial for accurate flow field measurements. While numerous methods exist for planar PIV, fewer have been developed for volumetric PIV systems, and in particular for coaxial setups like robotic volumetric PIV. Light reflections in volumetric PIV experiments result in high-intensity regions that corrupt particle detection and analysis. This study presents a novel approach for treating light reflections in robotic volumetric PIV experiments. The proposed method uses image filtering and masking techniques in the wavenumber space to separate particle images from reflection regions. The process involves decomposing the image signal into low- and high-wavenumber components using the 2D discrete Fourier transform (DFT) to then use a high-pass filter to attenuate the intensity of the reflection regions. Finally, a step of automated adaptive masking is applied to remove residual reflection areas that the filtering is not able to eliminate. The proposed approach is tested on experimental data obtained from experiments performed using robotic volumetric PIV on two different geometries: a side-view mirror and a rotating two-blade propeller. Comparison between raw and pre-processed images, as well as particle tracking results, is presented. The results from this data comparison show successful removal of reflection-induced artifacts in instantaneous images by using the spatial Fourier filter automated masking approach. The developed image pre-processing strategy effectively removes unsteady light reflection regions in robotic volumetric PIV images, preventing the appearance of spurious particle tracks and improving the accuracy of flow field measurements. The spatial gaps introduced by the masking procedure can be easily filled in via measurements from multiple directions, which are promptly achieved via the robotic volumetric PIV approach.

Simulation of the reflection of a high energy laser beam at the sea surface for hazard and risk analyses

The application of a high energy laser beam in a maritime scenario necessitates a laser safety concept to prevent injury to personnel or uninvolved third parties from uncontrolled reflections of laser light from the sea surface. Therefore, it is crucial to have knowledge of the amount and direction of reflected laser energy, which varies statistically and depends largely on the dynamics of the wavy sea surface. These dynamics are primarily influenced by wind speed, wind direction, and fetch. An analytical model is presented for calculating the time-averaged spatial intensity distribution of the laser beam reflected at the dynamic sea surface. The model also identifies the hazard areas inside which laser intensities exceed a fixed exposure limit. Furthermore, as far as we know, our model is unique in its ability to calculate the probabilities of potentially eye-damaging glints for arbitrary observer positions, taking into account the slope statistics of gravity waves. This is a critical first step toward an extensive risk analysis. The simulation results are presented on a hemisphere of observer positions with fixed radii from the laser spot center. The advantage of the analytical model over our numeric (dynamic) model is its fast computation time. A comparison of the results of our new analytical model with those of the previous numerical model is presented.

A versatile setup for nanosecond laser polishing processes with in situ analysis capabilities.

Laser polishing of material surfaces is a complex process depending on many variable parameters, such as, e.g., the properties of the used laser and optics (wavelength, pulse duration, fluence, and profile), as well as the processing (spot size, feed rate, and line or point overlap), and the thermodynamical properties of the material to be polished (heat capacity, heat conduction, etc.). For the successful laser polishing of any material, a systematic variation of all the process parameters is required to obtain satisfactorily polished surfaces with an appropriate set of parameters for the material of interest. In order to allow systematic studies of laser polishing processes, a new setup employing a highly stable nanosecond laser with an adjustable wavelength has been realized. The sample is located in a small high-vacuum chamber with the capability of introducing additional gases in a controlled manner, and the entire chamber is scanned in the beam to allow laser polishing of selected spots, lines, or larger areas. The setup is fully remote-controlled and allows in situ inspection of the initiated processes by means of a long-range microscope, electrical measurements, reflected laser light from the sample surface, and an analysis of the vacuum within the process chamber. The main properties of the setup will be presented, and some exemplary results on niobium and molybdenum metal samples will be discussed.

Correlation between keyhole geometry and reflected laser light distribution in laser-based manufacturing

This study investigated the correlation between the keyhole geometry and reflected laser light distribution during laser-based manufacturing processes. An “imaging dome” system was developed to capture the distribution of the reflected laser light on a registration dome during the process, and found that the reflected laser distribution varied significantly as the keyhole shape was changed by reducing the laser scanning speed. A numerical model was leveraged to understand the multiple reflections of laser rays within the keyholes of different geometries. The results demonstrated the potential of a novel approach for in-situ detection of keyhole shapes during laser-based manufacturing.

Acoustic Roughness Measurement of Railway Tracks: Running Surface Detection and Compensation of Lateral Movements for Optical Measurements on a Train.

Rolling noise is a significant contributor to railway noise. Wheel and rail roughness are decisive for the emitted noise level. An optical measurement method installed on a moving train is suitable for closer monitoring of the rail surface condition. A measurement setup based on the chord method requires the sensors to be positioned in a straight line along the direction of measurement and in a stable lateral position. Measurements should always be performed within the shiny and uncorroded running surface, even when there are lateral movements of the train. In this study, concepts for the detection of the running surface and the compensation of lateral movements are investigated in a laboratory setting. The setup consists of a vertical lathe with a ring-shaped workpiece that incorporates an implemented artificial running surface. The detection of the running surface based on laser triangulation sensors and a laser profilometer is investigated. It is shown that the running surface can be detected using a laser profilometer that measures the intensity of the reflected laser light. It is possible to detect the lateral position and the width of the running surface. A linear positioning system is proposed to adjust the lateral position of the sensors based on the running surface detection of the laser profilometer. When the lateral position of the measuring sensor is disturbed by a movement with a wavelength of 18.85 m, the linear positioning system can keep the laser triangulation sensor inside the running surface for 98.44% of the measured data points at a velocity of approximately 7.5 km h-1. The mean positioning error is 1.40 mm. By implementing the proposed system on the train, future studies can be conducted to examine the lateral position of the running surface as a function of the various operational parameters of the train.

Application of Planar Laser-Induced Fluorescence for Interfacial Transfer Phenomena

The present review describes the current achievements in the applications of a planar laser-induced fluorescence (PLIF) method for the diagnostics of liquid films, bubbles, individual droplets, and sprays. Such flows are related with strongly curved interphases, which often results in additional high errors during the PLIF data quantification because of laser light reflection, refraction, and absorption. The present review demonstrates that a two-color PLIF approach and a PLIF modification for regularly structured illumination resolves the reflection- and refraction-caused errors. The latter modification ensures proper phase separation in the measurement cross-section and visualization of the interface dynamics. The former approach provides the accurate evaluation of the local temperature and concentration both in liquid and gaseous phases even in the case of strong variations of the laser sheet intensity. With intensified cameras, the PLIF method is used for multi-parameter diagnostics of the two-phase combustion of sprays in combustion chambers with optical access. It visualizes and quantifies the liquid fuel evaporation and mixing, to measure temperature in the gas and liquid phases and to reveal the regions of pollutant formation. The PLIF technique can also be easily combined with a particle image (or tracking) velocimetry method, to evaluate local heat and mass transfer.

Flange-type liquid-level sensor based on laser light reflection

We report a liquid-level sensor composed of a laser, prism, and photodiode array. The sensor does not require components, such as a sensor head, inside the container that stores liquid. The sensor detects the liquid level based on the difference between the intensities of laser light reflected at the liquid/glass and air/glass interfaces. As the detected liquid level shows a shift from the correct liquid level owing to surface tension and the broadening of the laser light, we correct the shift through calculations. The sensor can be attached to a flange-type glass viewport, providing compatibility with broad-ranging containers for industrial use. The sensor can accurately detect the liquid level with a maximum error of 0.3875 ​mm. We demonstrate the implementation and operation of the liquid-level sensor using a wireless system comprising a sensor head and wireless voltmeter. The reported sensor allows accurate measurement of the liquid level in a tank inside which foreign objects such as sensor heads cannot be installed.

Photon propagation during source/target shifts falsifies special theory time dilation

Reflected laser light spots on distant targets were observed for 24 h periods by two separate laboratories. Although claims made in one study suggested this was not the case, in fact both data sets indicate no sufficiently significant shift of the centers of the reflected spots on the targets as the earth orbited and revolved during the measurements. This means that photons from the laser sources also travel lateral with the earth and targets so as not to shift the target arrival spot. This demonstrates the phenomenon termed synchronous aberration. The fact that photons do not follow the linear line along the ground between source and target but rather follow a diagonal, from the source at an original position to the target at a later shifted position, means that a stationary outside observer, but not an observer moving with the system, could be aware of the distance traveled to compute time for the event. Time dilation due to motion in special relativity theory is thus disproven, where a moving observer would merely use the ground distance between source and target to compute time incorrectly. Time for a light event is not dependent on motion of an observer that does not control the event, but may be incorrectly computed by an observer in motion. Physics texts must be corrected to avoid this long-held misconception in the future.

Suppression Of Wall Reflection In PIV Images Over Rough Walls

Wall reflections in particle image velocimetry (PIV) measurements is one of the limiting factors in obtaining velocity information in the vicinity of rough walls. This work tests two different techniques to suppress wall reflections for time-resolved, two-dimensional particle tracking velocimetry (2D-PTV) and stereoscopic-PIV (stereo-PIV). The 2D-PTV was performed for a turbulent boundary layer developed on a rough wall in a water towing tank facility. To measure velocity in the vicinity of the rough wall, the near-wall region on the viewing window was covered with tinted papers to mitigate the wall reflection and maintain a visible reference plane of the towed wall. Using this technique allowed detection of particles at a wall-normal distance of approximately 300 μm (10 wall units) from the roughness valleys for an imaging system with 1 m standoff distance. To suppress the wall refection for the stereo-PIV over a rough wall performed in a wind tunnel, the roughness is coated with fluorescent paint to shift the reflected light to a higher wavelength. A narrow band-pass filter was then used on the imaging lenses, allowing only particle images to be recorded while extinguishing the majority of the reflected laser light from the surface. Reliable velocity measurements with this technique were obtained up to 500 μm (5.0 wall units) from the roughness valleys.

Polarization-dependent LIF/Mie ratio for sizing of micrometric ethanol droplets doped with Nile red.

The present study deals with droplet sizing based on laser-induced fluorescence (LIF) and Mie scattering for varied polarization of the utilized laser (parallel or perpendicular). The polarization-dependent LIF/Mie ratio is studied for micrometric droplets (25-60 µm) produced with a droplet generator. The investigations were carried out with the dye Nile red dissolved in ethanol and ethanol/iso-octane mixtures. A spectral absorption and fluorescence characterization at various dye and ethanol concentrations is carried out in a cuvette in order to identify reabsorption effects. The LIF|| droplet images (index ||: parallel polarization) show a more homogeneous intensity distribution in the droplets and slightly stronger morphology-dependent resonances (MDRs) in comparison to LIF⊥ (index ⊥: perpendicular polarization). The spectral LIF emissions reveal a dependence of the MDR on the ethanol admixture. The larger the ethanol content, the lower the MDR peak, which is also shifted further to the red part of the spectrum. The Mie droplet signal images are mainly characterized by two distinct glare points, one at the entrance of the laser light (reflection) and one at the exit (first-order refraction). The Mie⊥ images show a more pronounced entrance glare point, in comparison to Mie||, where the exit glare point is more pronounced. These observations are in accordance with the theory. The calibration curve of the micro droplet signals revealed a volumetric trend of the LIF signals and a slightly higher LIF⊥ signal and sensitivity in comparison to LIF||. The signal Mie⊥ follows roughly a quadratic trend on average, while Mie|| follows a linear trend. Consequently, the calculated LIF⊥/Mie⊥ ratio shows a linear trend, whereas the LIF||/Mie|| ratio shows a quadratic trend, which confirms theoretical calculations. A numerical simulation of the Mie signal at various detection angles shows a good agreement with the experimental data at large apertures.

Particle Manipulation in 2D Space Using a Capacitive Micromachined Ultrasonic Transducer.

Ultrasonic particle manipulation is a noncontact method for controlling microscale objects, such as cells or microparticles, using an acoustic field. In this study, a 2D array of capacitive micromachined ultrasonic transducers (CMUTs), placed horizontally in immersion, generated ultrasonic waves in the vertical direction, and the oil’s surface increased due to the radiation force of the ultrasonic waves. In addition, the radiation force directly exerted a force on a floating particle. By measuring the movement of the reflected laser light by the moving oil surface, the height of the oil’s surface deformed by the acoustic radiation force (ARF) was measured. The ARF made a floating particle, as well as the oil’s surface, move. The particle moved radially away from the surface position above the transducer, and its velocity was determined by its position on the fluid’s surface. When a single channel was operated, it moved 0.4 mm at an average speed of 90 μm/s, and when two adjacent channels were operated, it moved 1.2 mm at a speed of 272 μm/s. The particles moved in any direction on the surface of the oil by controlling the actuation channel using an electrical switch.

Characterization of bituminite in Kimmeridge Clay by confocal laser scanning and atomic force microscopy

This work investigates bituminite (amorphous sedimentary organic matter) in Upper Jurassic Kimmeridge Clay source rock via confocal laser scanning microscopy (CLSM) and atomic force microscopy (AFM). These petrographic tools were used to provide better understanding of the nature of bituminite, which has been historically difficult to identify and differentiate from similar organic matter types in source rocks. As part of an International Committee for Coal and Organic Petrology (ICCP) working group, an immature (0.42% vitrinite reflectance), organic-rich (44.1 wt% total organic carbon content) sample of Kimmeridge Clay was distributed to multiple laboratories for CLSM characterization. The primary observations from CLSM imaging and spectroscopy include: 1) the interpreted presence of Botryococcus algae as a contributor to bituminite precursors; 2) color red-shift of sulfide reflectance and bituminite auto-fluorescence from below the sample surface; 3) positive alteration of bituminite from laser-induced photo-oxidation of the sample surface, including fluorescence blue-shift; 4) fluorescence blue-shift associated to higher fluorescence intensity regions in bituminite indicative of compositional (fluorophore) differences; 5) the need for fluorescence spectroscopy standardization as applied via CLSM; and 6) the suitability of CLSM fluorescence spectroscopy to predict solid bitumen reflectance from bituminite spectral emission via calibration to an extant dataset. Secondary CLSM observations include detection of reflected laser light from highly reflective inclusions in bituminite, including sulfides and fusinite, and radiolytic alteration of bituminite caused by substitution of U for Fe in sulfides. Findings from AFM include the observation that surface roughening or surface flattening of bituminite are induced by differential broad ion beam (BIB) milling and are dependent on the location and scale of AFM topology measurement. This result highlights our still limited understanding of the effects of BIB milling on sedimentary organic matter and indicates the need for further research before this technique can be advanced as a standard practice in petrographic sample preparation. Collectively, the results of this study illustrate the general applicability and versatility of AFM and CLSM as tools for organic petrology research, specifically for better understanding of the nature and properties of the bituminite maceral.

Entry Mechanism of small particles into friction interface in lubricating oil

In general, sliding parts of machines should avoid wear particles entering into a contact area to enlongen lifetime of those parts. To observe wear particles which entering into a contact point by using optical microscope and high speed camera is thought to be one of the potential candidate to elcidate life of the parts. However, it is challenging to see those particles of sub-micrometer diameter because of diffraction limit. The authors have been trying to develop iFLAT (intelligent Fluorescent Light Assisted Tribometer) to orvercome this diffraction limit. It can observe fluorescent stained particles which emits fluorescent light by 532 nm laser. The laser irradiates the friction surface through the objective lens, and the reflected light passes through the filter and enters the camera. The reflected laser light is blocked by a filter, and the imitated wear particles that emit fluorescence are selectively observed.

Artificial red blood cells increase large vessel wall damage and decrease surrounding dermal tissue damage in a rabbit auricle model after subsequent flashlamp-pumped pulsed-dye laser treatment.

Artificial red blood cells (i.e. hemoglobin [Hb] vesicles [Hb-Vs]) function effectively as photosensitizers in flashlamp-pumped pulsed-dye laser (PDL) treatment for port-wine stains in animal models. Hb-Vs deliver more Hb to the vicinity of the endothelial cells. Both Hb-Vs and red blood cells absorb the laser energy and generate heat, supporting the removal of very small blood vessels and deeper subcutaneous blood vessels with PDL irradiation in in vivo experiments. Here, we analyzed the photosensitizing effect of Hb-Vs in PDL irradiation on large blood vessels and surrounding soft tissues. We histopathologically analyzed markers of damage to the large vessels and surrounding dermal tissue in a rabbit auricle model following PDL irradiation alone or subsequent to the addition of intravenous Hb-V injection. Markers were graded on a five-point scale and statistically compared. The changes in laser light absorption and reflection in a human skin model caused by the administration of Hb-Vs were evaluated using Monte Carlo light-scattering programs. Histological markers of damage to blood vessels were significantly greater in Hb-V-injected arteries and veins measuring 1-3mm in diameter as compared with the controls. However, Hb-V injection significantly reduced PDL-induced necrosis and hemorrhage in the surrounding tissues. During computer simulation, photon absorption increased within the vessel layer and decreased around the layer. Intravenous Hb-Vs increase the extent of damage in larger vessel walls but significantly reduce damage to the surrounding skin after subsequent PDL irradiation. These beneficial effects are the result of improving vessel selectivity by Hb-Vs in vessels. Hb-V administration prior to PDL irradiation therapy could mechanically improve the outcomes and safety profiles of port-wine stain treatment protocols.

High-resolution velocimetry technique based on the decaying streaks of phosphor particles.

This Letter introduces a new, to the best of our knowledge, particle streak velocimetry technique based on decaying streaks formed by individual phosphor particles following pulsed excitation. Tin-doped phosphor particles are dispersed into flows and excited by a pulsed UV laser light sheet. Emission streaks are recorded as a result of particle motion during the persistence of luminescence (here ∼27µs). The two components of the flow velocity are derived from the streaks without directional ambiguity by applying to each streak a two-dimensional fit describing a linearly moving point source with a mono-exponential decaying emission. This technique can achieve high spatial resolution compared to particle image velocimetry (PIV), while also requiring much fewer computational resources than particle tracking velocimetry (PTV) at high seeding densities. The wavelength-shifted luminescence also allows rejection of reflected laser light. The approach was validated in a free jet against simultaneous PTV and PIV and then successfully applied to measure a canonical boundary layer flow.

Design of an electrostatic balance mechanism to measure optical power of 100 kW.

A new instrument is required to accommodate the need for increased portability and accuracy in laser power measurement above 100 W. Reflection and absorption of laser light provide a measurable force from photon momentum exchange that is directly proportional to laser power, which can be measured with an electrostatic balance traceable to the SI. We aim for a relative uncertainty of 10-3 with coverage factor k = 2. For this purpose, we have designed a monolithic parallelogram 4-bar linkage incorporating elastic circular notch flexure hinges. The design is optimized to address the main factors driving force measurement uncertainty from the balance mechanism: corner loading errors, balance stiffness, stress in the flexure hinges, sensitivity to vibration, and sensitivity to thermal gradients. Parasitic rotations in the free end of the 4-bar linkage during arcuate motion are constrained by machining tolerances. An analytical model shows this affects the force measurement less than 0.01 percent. Incorporating an inverted pendulum reduces the stiffness of the system without unduly increasing tilt sensitivity. Finite element modeling of the flexures is used to determine the hinge orientation that minimizes stress which is therefore expected to minimize hysteresis. Thermal effects are mitigated using an external enclosure to minimize temperature gradients, although a quantitative analysis of this effect is not carried out. These analyses show the optimized mechanism is expected to contribute less than 1 × 10-3 relative uncertainty in the final laser power measurement.

Velocity Measurement of a Highspeed Underwater Projectile With Laser Barriers

To improve the precision of velocity measurements for high-speed underwater projectiles and meet the requirements for device terminal alarms, a method for identifying and measuring high-speed underwater projectiles with a large-area laser barrier was proposed. The absorption of laser transmission underwater and the relationship between scattering and suspended particles were simulated and analyzed. An optical system consisting of a waterproof modulated laser transceiver probe, multifiber transmission and a retroreflector was designed to decrease the large optical energy dissipation. The laser beam was expanded to form a triangular barrier with a Powell prism. The fiber array surrounding the prism receives the reflected laser light from the retroreflector. The other end of the optical fiber is coupled to a PIN-PD detector through a narrowband filter. The output electric signal is then processed by an amplifier, demodulator and low-pass filter. The shortcomings of traditional split-type and multielement optical structures in water were effectively overcome by this compact integrated probe structure, and the effective area was expanded to <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$2 m \times 2 m$ </tex-math></inline-formula> . The velocity of high-speed underwater steel balls and lead blocks, the simulated projectiles, was acquired accurately to verify the feasibility of velocity measurement for high-speed underwater projectiles with laser barriers.

Time-dependent measurement of high-power laser light reflection by low-Z foam plasma

Abstract Porous materials have many applications for laser–matter interaction experiments related to inertial confinement fusion. Obtaining new knowledge about the properties of the laser-produced plasma of porous media is a challenging task. In this work, we report, for the first time to the best of our knowledge, the time-dependent measurement of the reflected light of a terawatt laser pulse from the laser-produced plasma of low-Z foam material of overcritical density. The experiments have been performed with the ABC laser, with targets constituted by foam of overcritical density and by solid media of the same chemical composition. We implemented in the MULTI-FM code a model for the light reflection to reproduce and interpret the experimental results. Using the simulations together with the experimental results, we indicate a criterion for estimating the homogenization time of the laser-produced plasma, whose measurement is challenging with direct diagnostic techniques and still not achieved.

Giant dipole moment induced by an interface

When a small particle is illuminated by a laser beam, an oscillating electric dipole moment is induced. When located near an interface, the reflected laser light will change the local electric field, and thereby the dipole moment. However, also the dipole radiation, emitted by the particle, reflects at the interface, and contributes to the electric field at the location of the particle. This reflected field alters the dipole moment. We find that, under certain circumstances, the induced dipole moment by the dipole's own radiation far exceeds the dipole moment induced by the laser.

Electro-Ionic Control of Surface Plasmons in Graphene-Layered Heterostructures.

Precise control of light is indispensable to modern optical communication devices especially as the size of such devices approaches the subwavelength scale. Plasmonic devices are suitable for the development of these optical devices due to the extreme field confinement and its ability to be controlled by tuning the carrier density at the metal/dielectric interface. Here, an electro-ionic controlled plasmonic device consisting of Au/graphene/ion-gel is demonstrated as an optical switch, where an external electric field modulates the real part of the electrical conductivity. The graphene layer enhances charge penetration and charge separation at the Au/graphene interface resulting in an increased photoinduced voltage. The ion-gel immobilized on the Au/graphene further enables the electrical tunability of plasmons which modulates the intensity of the reflected laser light. This work paves the way for developing novel plasmonic electro-optic switches for potential applications such as integrated optical devices.