Reference Measurement Procedure Research Articles

Strategies to verify equimolar peptide release in mass spectrometry-based protein quantification exemplified for apolipoprotein(a).

Quantitative protein mass spectrometry (MS) is ideally suited for precision diagnostics and for reference standardization of protein analytes. At the Leiden Apolipoprotein Reference Laboratory we apply MS strategies to obtain detailed insight into the protein-to-peptide conversion in order to verify that quantifier peptides are not partly concealed in miscleaved protein backbone. Apolipoprotein(a) (apo(a)) was digested in a non-optimal manner to enhance the number of miscleaved peptides that were identified by high resolution liquid chromatography tandem-MS measurements. The protein-to-peptide conversion was carefully mapped with specific attention for miscleaved peptides that contain an apo(a) quantifier peptide. Four different isotopologues of each apo(a)-quantifier peptide were applied to evaluate linearity of internal peptide standards during measurement of specific real-life samples. Two apo(a) quantifier peptides that were concealed in two different miscleaved peptides were included into a multiple reaction monitoring list in our targeted MS-based apo(a) quantifications to alert for potential protein digestion discrepancies. The presence of miscleaved peptides could be ruled out when applying our candidate reference measurement procedure (RMP) for apo(a) quantification. These data further corroborate the validity of our apo(a) candidate RMP as higher order method for certification of commercial Lp(a) tests that is endorsed by theInternational Federation of Clinical Chemistry and Laboratory Medicine. MS-based molecular detection and quantification of heterogeneous apo(a) proteoforms will allow manufacturers' transitioning from confounded lipoprotein(a) [Lp(a)] mass levels into accurate molar apo(a) levels.

Establishment of potential reference measurement procedure and reference materials for EML4-ALK fusion variants measurement

Echinoderm microtubule-associated protein 4 (EML4) - anaplastic lymphoma kinase (ALK) fusion gene detection is of great significance in personalized tumor treatment. With the development of EML4-ALK fusion variants detection, it is necessary to establish traceability to ensure the consistency and comparability of its detection results in clinical practice. The establishment of traceability relies on SI traceable reference materials (RMs) and potential reference measurement procedures (RMPs). In this study, a potential RMP for the quantitative detection of V1 and V3 fusion mutations and the reference type (ALK-ref, including wild type, V1 and V3 mutant type) based on reverse transcription dPCR (RT-dPCR) and EML4-ALK fusion gene RMs were established. The proposed potential RMP has high specificity, good inter-laboratory reproducibility (CV < 7.3%) and good linear relationship (0.92 < slope < 1.06, R2 ≧ 0.99). The limit of detection (LoD) of V1, V3, and ALK-ref are 2 copies/reaction, 2 copies/reaction, and 1 copy/reaction, respectively. Interlaboratory studies using the EML4-ALK RMs and potential RMP showed that participating laboratories can produce consistent copy concentrations of fusion variant and ALK-ref as well as the ratio of EML4-ALK/ALK-ref. The established potential RMP with high specificity and accuracy can be used to characterize the EML4-ALK RMs, and the potential RMP and RM are useful to establish the traceability of EML4-ALK fusion measurement to improve the comparability and consistency in clinical tests.

Clinical application of an optimized reference measurement procedure for serum digoxin using bracketing calibration method by ID-LC-MS/MS.

Digoxin, a cardiac glycoside, is widely used in the treatment of cardiovascular diseases. Due to its narrow therapeutic range, precise monitoring of its blood concentration is essential. Areference measurement procedure (RMP) is pivotal for ensuring result accuracy and comparability. The RMP for serum digoxin by ID-LC-MS/MS was optimized with sample pre-treatment and detection processes, and the bracketing calibration method was used, which facilitates more accurate measurement, especially for extreme concentrations. The performance of this optimized RMP was thoroughly evaluated. The limit of detection (LoD) was 0.05 ng/mL (0.06 nmol/L) and the lowest limit of quantification (LLoQ) was 0.10 ng/mL (0.13 nmol/L). The intra- and inter-assay imprecisions were 2.24%, 2.51%, 1.40% and 1.72%, 1.65%, 0.97% at 0.5, 2.0, 5.0 ng/mL, respectively. Recoveries were 99.63 to 101.42% and thelinear response ranged from 0.1 to 10.0 ng/mL. The relative bias was 0.41% and 2.00% of our results compared with the median of all participating reference laboratories for IFCC-RELA (External Quality Assessment Scheme for Reference Laboratories in Laboratory Medicine) 2023A and 2023B. The uncertainty, calibration and measurement capability (CMC) of this method were also evaluated. The optimized RMP was applied in the Trueness Verification Plan of Southern China, which indicates significant differences among clinical systems, highlighting the need for standardization efforts. In addition, two commonly used clinical systems which employed immunoassay methods were compared with this optimized RMP, and 26 individual serum samples were analyzed. The good correlations indicate the feasibility of standardization for serum digoxin. The optimized RMP serves as an accurate reference baseline for routine methods, aiming to enhance the accuracy and precision of measurements in clinical laboratories.

6651 A Traceable Clinical Free Thyroxine Assay Based on Equilibrium Dialysis ID-LC/MS/MS

Abstract Disclosure: D. Spector: None. L. Zhang: None. A. Ribera: None. A. Doty: None. C. Tse: None. O. Sugahara: None. N. Vazquez: None. U. Danilenko: None. H.W. Vesper: None. Accurate diagnosis and effective treatment of thyroid diseases rely on reliable thyroid function tests. Serum free thyroxine (FT4) immunoassays (IAs) are most commonly used for FT4 measurements in clinical practice. However, FT4 IAs have not been standardized with large variations between different assay platforms. A reference measurement procedure (RMP) for FT4 based on well-defined equilibrium dialysis (ED) of serum has been established for CDC standardization program to support the standardization of clinical assays for patient care. In the current study, we aim to develop a routine clinical FT4 assay based on ED-LC/MS/MS that is traceable to the RMP. ED-LC/MS/MS analysis was performed using a commercially available micro-ED plate. FT4 in dialysate was extracted with a 96-well C18 SPE plate. FT4 in the samples was quantitated by using LC/MS/MS in positive ion mode. The assay was calibrated with the certified primary reference material. By using RMP as a reference, we compared the analysis of 40 single donor sera between the ED-LC/MS/MS assay and FT4 IA on Roche e401platform. ED-LC/MS/MS assay could resolve T4, T3, reverse triiodothyronine (rT3), and other interferences in the samples with C18 chromatography in 4 min. The linear range of the routine FT4 assay was from 0.5-100 pg/mL covering clinically relevant FT4 concentrations including hypo-, hyperthyroid patient samples. The intra and inter-run CV% of the assay in 20 days was 3.72 and 5.25%, respectively. The effect of minor changes to the method conditions was studied. It was determined that serum/buffer ratios from 1:1 to 1:2 in the ED inserts, speeds of shaker for ED, and ED incubation time, did not influence the FT4 measurement. However, elevated ED temperature at 38°C could result in a more than 10% increase in FT4 values. A microplate format for the procedures of ED and SPE is amiable to the application of an automation system which significantly improves the throughput of the procedure. Method comparison showed good agreement between ED-LC/MS/MS assay and RMP in Deming regression analysis with a slope close to 1, while there was significant bias of IA from RMP. ED-LC/MS/MS assay was also applied for pregnancy serum samples with minimal difference on the FT4 measurement from RMP. We have developed a routine clinical FT4 assay that is traceable to RMP. The accuracy, precision, and sensitivity of the assay are suitable for high-throughput FT4 measurements in clinical laboratories and large epidemiologic studies. We demonstrate that the developed method can provide accurate FT4 measurements in patients including pregnant women. Presentation: 6/3/2024

6848 Improvement Of Free Thyroxine Measurement Quality Through The CDC Clinical Standardization Programs

Abstract Disclosure: A. Ribera: None. N. Vazquez: None. S. Knoblock: None. O. Sugahara: None. T. Buchannan: None. L. Collins: None. D. Spector: None. L. Zhang: None. U. Danilenko: None. H.W. Vesper: None. Thyroid function tests are among the most requested tests in patient care, and reliability of these measurements are crucial for appropriate diagnosis and management of thyroid disorders. In response to concerns from the clinical and research community about the quality of thyroid function tests, the CDC Clinical Standardization Programs (CSP) has created the hormone standardization (HoSt) program for free thyroxine (FT4) in partnership with the International Federation for Clinical Chemistry and Laboratory Medicine (IFCC). As a first step, CDC CSP has completed an interlaboratory comparison study of commercial immunoassays (IA) and lab-developed tests (LDT) to determine the current agreement among assays. Participants received 40 blinded, high quality individual donor serum samples with FT4 reference values assigned by the CDC FT4 reference measurement procedure (RMP). FT4 concentrations ranged between 11-32 pmol/L. Samples were analyzed in duplicate over 2 days and results were compared to the CDC FT4 RMP. To assess the potential impact of standardizing measurements to the CDC HoSt FT4 program, reported results were normalized to the CDC RMP results (recalibrated in silico using linear regression). Mean percent bias to the reference value was evaluated pre- and post-recalibration. In addition, inter-assay agreement of classification (assignment of hypo-, eu- or hyperthyroid status according to FT4 reference intervals) were assessed pre- and post-recalibration using the assay-specific and CDC RMP reference intervals, respectively. A total of 19 methods participated, consisting of 15 IA and 4 LDT. All participants showed a negative mean bias to the RMP, with IA showing a higher magnitude of bias (average: -20.7 ± 0.9%) than LDT (average: -4.7 ± 1.1%). Of the 40 samples measured, only 53% were classified uniformly by all 19 participants. Post-recalibration, mean percent bias improved profoundly (IA average: 0.0 ± 0.8%, LDT average: 0.1 ± 1.1%), and classification agreement improved by 33% to 86% of samples with consistent classification. The CDC CSP interlaboratory comparison among FT4 assays highlights the critical need for measurement standardization to improve accuracy of FT4 measurements and increase consistency in result interpretation. This study demonstrates that it is possible to develop common FT4 reference intervals via measurement standardization, which would allow for universal evidence-based clinical guidelines to be used in patient care. Presentation: 6/3/2024

Expedient measurement of total protein in human serum and plasma via the biuret method using fiber optic probe for patient samples and certified reference materials.

The biuret method is currently recognized as a reference measurement procedure for serum/plasma total protein by the Joint Committee for Traceability in Laboratory Medicine (JCTLM). However, as the reaction involved in this method is highly time-dependent, to ensure identical measurement conditions for calibrator and samples for high accuracy, a fast and simple measurement procedure is critical to ensure the precision and trueness of this method. We measured serum/plasma total protein using a Cary 60 spectrophotometer coupled with a fiber optic probe, which was faster and simpler than the conventional cuvette method. The biuret method utilizing alkaline solutions of copper sulfate and potassium sodium tartrate was added to the sample and calibrator (NIST SRM 927e) incubated for 1h before measurement. A panel of samples consisting of pooled human serum, single donor serum, and certified reference materials (CRMs) from three sources were measured for method validation. Sixteen native patient samples were measured using the newly developed biuret method and compared against clinical analyzers. Additionally, the results of three cycles of a local External Quality Assessment (EQA) Programme submitted by participating clinical laboratories were compared against the biuret method. Our biuret method using fiber optic probe demonstrated good precision with within-day relative standard deviation (RSD) of 0.04 to 0.23% and between-day RSD of 0.58%. The deviations between the obtained values and the certified values for all three CRMs ranged from -0.38 to 1.60%, indicating good method trueness. The routine methods using clinical analyzers were also found to agree well with the developed biuret method using fiber optic probe for EQA samples and native patient samples. The biuret method using a fiber optic probe represented a convenient and reliable way of measuring serum total protein. It also demonstrated excellent precision and trueness using CRMs and patient samples, which made the method a simpler candidate reference method for serum protein measurement.

B-021 Impact of Assay Conditions on FT4 Measurement Accuracy of Equilibrium Dialysis LC/MS/MS Clinical Assay

Abstract Background Reliable FT4 measurements are vital for accurate diagnosis and effective management of thyroid disorders. However, currently used FT4 immunoassays (IAs) lack standardization, leading to significant variations between platforms. Equilibrium dialysis (ED) coupled with LC-MS/MS analysis, considered the gold standard for FT4 measurement, has been adopted as a reference measurement procedure (RMP) for IA standardization. This study aimed to establish a high-throughput version of the routine clinical FT4 assay based on ED-LC/MS/MS technology and assess the impact of altered assay conditions on measurement accuracy. Methods A commercially available micro-ED plate was employed for ED-LC/MS/MS analysis. FT4 extraction from the dialysate was performed by utilizing a 96-well C18 SPE plate, followed by FT4 quantitation via LC-MS/MS in positive ion mode. Certified primary reference material was used to calibrate the assay. To evaluate assay robustness, the effects of minor method modifications were studied, including incubation time of ED, serum/buffer ratios in ED inserts, ED incubation temperature, shaker speed during ED, serum sample dilution ratio, and dialysate sample dilution ratio. Additionally, short-term and long-term stability of serum FT4 were assessed. Results The developed ED-LC/MS/MS assay successfully resolved T4, T3, reverse triiodothyronine (rT3), and other interferences within 4 minutes using C18 chromatography. The assay's linear range (0.5-100 pg/mL) encompassed clinically relevant FT4 concentrations across hypo- and hyperthyroid patient samples. Excellent agreement was observed between the routine assay based on ED-LC/MS/MS and CDC RMP with a Deming regression slope near 1 (95%CI: 0.87-1.06). Furthermore, serum/buffer ratios from 1:1 to 1:2.5 in ED inserts, shaker speeds from 75 to 150 rpm, and ED incubation times from 16 to 20 hours did not significantly affect FT4 measurement. However, elevated ED temperature (38°C) led to a more than 10% increase in FT4 values. Serum FT4 remained stable when exposed to room temperature for 12 hours, five freeze-thaw cycles, and -70°C storage for 1.5 years. Additionally, dilution of sera by up to 3-fold before ED did not alter FT4 measurement results. Diluting dialysate samples at least 3 times prior to SPE extraction proved accurate for samples exceeding the calibration curve range. Conclusions In conclusion, we successfully developed a routine clinical FT4 assay based on ED-LC/MS/MS that generates data comparable to the RMP. The assay exhibits robustness, with several altered conditions not significantly impacting measurement accuracy. This high-throughput and accurate assay demonstrates suitability for both clinical laboratories and large-scale epidemiological studies. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the official position of the Centers for Disease Control and Prevention/the Agency for Toxic Substances and Disease Registry. Use of trade names is for identification only and does not imply endorsement by the Centers for Disease Control and Prevention, the Public Health Service, and the US Department of Health and Human Services.

A-338 Assessing the Technical and Analytical Performance of Point of Care Testing Devices for Blood Lipids Measurements

Abstract Background Cardiovascular diseases (CVDs) are the leading cause of death worldwide, causing over 17 million deaths each year. According to the World Health Organization (WHO), 85% of CVD deaths are due to heart disease and strokes, and over 75% occur in low- and middle-income countries (LMICs). Early detection and treatment are key to preventing consequences of CVD. Point-of-care testing (POCT) devices require minimal laboratory infrastructure and can be used to screen hard-to-reach populations for CVD risk. These devices are increasingly used in traditional care settings including hospitals and primary healthcare, and in non-traditional settings such as pharmacies. Although POCT devices offer fast and convenient testing, the analytical performance of these devices must produce accurate and reliable results, and have technical suitability for use. Several POCT devices for total cholesterol (TC) and other blood lipids are commercially available, however, the operational and analytical performance of these devices is not fully known. Methods Eight POCT devices for blood lipids were used in this study. For the technical assessment, a checklist was developed and applied, outlining the operational functionality and environmental conditions of the devices. Some relevant technical parameters in this checklist included requirements for temperature/humidity and power/voltage, storage conditions, and assay/test time. The analytical performance was assessed for parameters, such as accuracy and imprecision, using paired whole blood and serum donor samples for TC. In addition, these analytical parameters were assessed for serum High Density Lipoprotein-cholesterol (HDL-c) and Low Density Lipoprotein-cholesterol (LDL-c) samples on seven POCT devices. All samples were representative of a clinically relevant concentration range for TC, HDL-c, and LDL-c. Accuracy was compared to reference values obtained by the CDC reference measurement procedures. Results The mean bias for TC ranged among devices from -8.17% to 11.99% for whole blood and -7.89% to 7.02% for serum, respectively. The mean imprecision for TC in whole blood ranged from 1.94% to 11.63%, and in serum from 1.72% to 12.70%. The mean bias for serum HDL-c samples ranged from -7.33% to 17.36%, and for serum LDL-c samples from -20.92% to 5.04%. The mean imprecision for serum HDL-c samples ranged from 2.39% to 24.27% and for serum LDL-c samples ranged from 3.14% to 18.33%. For three of the eight devices, about 25% of the whole blood measurements and 50% of the serum measurements were reported outside of the measurement range and not included in the assessment. Comparing these non-reports with the reference values of these samples indicate that all of the reference values for whole blood and about 80% of the reference values for serum were actually within the measurement range of the device. Conclusions The technical assessment was helpful in building screening capacity in areas with limited laboratory infrastructure. The analytical assessment indicates notable differences in accuracy and precision for lipids measured in whole blood and serum, with serum measurements being more likely within performance requirements used by CDC's standardization programs. Additional studies to assess other devices and/or analytes, and future work to assist manufacturers improve the analytical performance of POCT devices are needed.

Absolute quantitation of human serum cystatin C: candidate reference method by 15N-labeled recombinant protein isotope dilution UPLC-MS/MS.

Serum cystatin C (CysC) is a reliable and ideal endogenous marker for accurately assessing early changes in glomerular filtration rate (GFR), surpassing the limitations of creatinine-based estimated GFR. To improve the precision of GFR calculation, the development of strategies for accurately measuring serum CysC is crucial. In this study, the full-length CysC pure product and fully recombinant 15N-labeled CysC internal standard were subjected to protein cleavage. Subsequently, an LC-MS/MS method was developed for the absolute quantification ofserum CysC. The traceability of the method was assigned calibrator using the amino acid reference measurement procedure (RMP). It involved calibrating the instrument using an amino acid reference material with known amino acid concentrations for calibration and comparison purposes. The total imprecision of the method was determined to be≤8.2 %, and a lower functional limit of quantification (LLoQ) was achieved. The recoveries ranged from 97.36 to 103.26 %. The relative bias between this candidate RMP for measurement of ERM-DA471-IFCC and the target value was 1.74 %. The linearity response was observed within the concentration range of 0.21-10.13 mg/L, with a high R2 value of 0.999. The results obtained using our method was consistent with those obtained using other certified RMPs. With the establishment of this highly selective and accurate serum CysC measurement method, it is now possible to assess the correlation between immunoassay results of serum CysC and the intended target when discrepancies are suspected in the clinical setting.

Feasibility of Metrological Traceability Implementation Using the Joint Committee on Traceability in Laboratory Medicine Database Entries Including the Fulfillment of "Fit-for-Purpose" Maximum Allowable Measurement Uncertainty.

In previous publications, the Task Force on Reference Measurement System Implementation proposed a procedural approach combining a critical review of entries available in the Joint Committee on Traceability in Laboratory Medicine (JCTLM) database with a comparison of this information against analytical performance specifications for measurement uncertainty (MU) and applied it to a group of 13 measurands. Here we applied this approach to 17 additional measurands, of which measurements are frequently requested. The aims of the study were (a) to describe the main characteristics for implementing traceability and the potential to fulfill the maximum allowable MU (MAU) at the clinical sample level of certified reference materials and reference measurement procedures listed in the JCTLM database; (b) to discuss limitations and obstacles, if any, to the achievement of the required quality of laboratory measurements; and (c) to provide a gap analysis by highlighting what is still missing in the database. Results were integrated with those obtained in the previous study, therefore offering an overview of where we are and what is still missing in the practical application of the metrological traceability concept to 30 common biochemical tests employed in laboratory medicine. Our analysis shows that for 28 out of 30 measurands, conditions exist to correctly implement metrological traceability to the International System of units and fulfill at least the MAU of the minimum quality level derived according to internationally recommended models. For 2 measurands (serum albumin and chloride), further improvements in MU of higher-order references would be necessary.

An ID-HPLC–MS/MS based candidate reference measurement procedure for the quantification of valproic acid in human serum

An ID-HPLC–MS/MS based candidate reference measurement procedure for the quantification of valproic acid in human serum

Extent of Equivalence of Results for Urine Albumin among 3 Candidate Mass Spectrometry Reference Measurement Procedures.

Urine albumin (UA) is an important biomarker of chronic kidney disease. Current in vitro diagnostic medical devices (IVD-MDs) for measuring UA are not standardized, and median results among IVD-MDs differ by approximately 45%. Since fixed decision values are used to interpret UA, higher-order reference measurement procedures (RMPs) are needed for metrological traceability. Three candidate liquid chromatography-tandem mass spectrometry RMPs have been developed for UA. Eight single-donation human urine samples were measured by 3 candidate RMPs. Results were compared using t-test and variance component analysis. The mean results for each urine sample from each RMP laboratory were not statistically different from the overall mean value by t-test. The median total CV including contributions from bias and imprecision among the 3 RMP laboratories was 6.23% using variance component analysis for each sample. The allowable bias to the RMP for an end-user IVD-MD was ≦9.0% or ≦3.0% based on the desirable or optimal total allowable error of 30% or 24%, respectively. A maximum allowable standard uncertainty for an RMP result was determined to be 4.3% or 3.3% for desirable or optimal performance, respectively. The standard uncertainties for all of the RMP laboratories meet the desirable and optimal standard uncertainty specifications. The candidate RMPs for UA in these 3 laboratories have suitable agreement of results and uncertainties for use as higher-order RMPs in the metrological traceability of end-user IVD-MDs for measuring UA.

Bilirubin measurements in neonates: uniform neonatal treatment can only be achieved by improved standardization.

Measurement of total bilirubin (TBil) concentration in serum is the gold standard approach for diagnosing neonatal unconjugated hyperbilirubinemia. It is of utmost importance that the measured TBil concentration is sufficiently accurate to prevent under treatment, unnecessary escalation of care, or overtreatment. However, it is widely recognized that TBil measurements urgently require improvement in neonatal clinical chemistry. External quality assessment (EQA) programs for TBil assess for differences between laboratories and provide supporting evidence of significant differences between various methods, manufacturers and measurement platforms. At the same time, many countries have adopted or only slightly adapted the neonatal hyperbilirubinemia management guidelines from the USA or UK, often without addressing differences in the methodology of TBil measurements. In this report, we provide an overview of the components of bilirubin that are measured by laboratory platforms, the availability of current reference measurement procedures and reference materials, and therole of EQA surveys in this context. Furthermore, the current status of agreement in neonatal bilirubin against clinical decision thresholds is reviewed. We advocate for enhancements in accuracy and comparability of neonatal TBil measurements, propose a path forward to accomplish this, and reflect on the position of the International Federation for Clinical Chemistry and Laboratory Medicine (IFCC) Working Group Neonatal Bilirubin (WG-NB) in this matter.

A candidate reference measurement procedure for quantification of glycocholic acid in human serum based on isotope dilution liquid chromatography-tandem mass spectrometry

Accurate measurement of serum glycocholic acid (GCA) is crucial for evaluating the activity of chronic hepatitis. Moreover, GCA is a novel identified biomarker for hepatocellular carcinoma. Although some laboratories have used the liquid chromatography-tandem mass spectrometry (LC–MS/MS) method to measure GCA in recent years, the problem of potential interference of GCA analogues has not been solved well yet. Neither reference measurement procedures nor reference materials for GCA have been listed in the Joint Committee for Traceability in Laboratory Medicine (JCTLM) database. For standardization of GCA, it is urgent to establish a candidate measurement procedure for GCA. In this study, a candidate reference measurement procedure for the quantification of GCA in human serum based on isotope dilution liquid chromatography-tandem mass spectrometry (ID-LC–MS/MS) by a two-step sample pretreatment of protein precipitation and MAX solid-phase extraction was developed and validated. GCA can be completely separated from its structural analogues with gradient elution in 9 min compared with short time gradients published in previous literature by Huang’s group. Method validation indicated perfect quantitation precision with intra-day and inter-day values that were ≤1.30% and ≤1.80%, respectively. The method showed excellent linearity with high regression coefficients (R2 > 0.999) over a range of 0.92 ng/g–38.38 μg/g and perfect recoveries at three spiked levels (99.87–100.43%). No interference, matrix effect, and carryover were observed. Moreover, the cRMP was successfully applied to measure GCA in serum samples and compared with two immunoassays in a clinical laboratory. As a candidate reference method, this method can promote a GCA standardization program.Graphical

Evaluation and clinical application of a bracketing calibration-based isotope dilution liquid chromatography-tandem mass spectrometry candidate reference measurement procedure for serum theophylline.

A candidate reference measurement procedure (RMP) for serum theophylline via isotope dilution liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed. With a single-step precipitation pretreatment and a 6-min gradient elution, the method achieved baseline separation of theophylline and its analogs on a C18-packed column. A bracketing calibration method was used to ensure repeatable signal intensity and high measurement precision. The intra-assay and inter-assay imprecisions were 1.06%, 0.84%, 0.72% and 0.47%, 0.41%, 0.25% at concentrations of 4.22 µg/mL (23.40 µmol/L), 8.45 µg/mL (46.90 µmol/L), and 15.21 µg/mL (84.43 µmol/L), respectively. Recoveries ranged from 99.35 to 102.34%. The limit of detection (LoD) was 2 ng/mL, and the lowest limit of quantification (LLoQ) was 5 ng/mL. The linearity range extended from 0.47 to 60 µg/mL (2.61-333.04 µmol/L). No ion suppression and carry-over (< 0.68%) were observed. The relative bias for this candidate RMP that participated in 2023 External Quality Control for Reference Laboratories (RELA) conducted by the International Federation of Clinical Chemistry (IFCC) was within a range of 0.17 to 0.93%. Furthermore, two clinical immunoassay systems were compared with this candidate RMP, demonstrating good correlations. The results of the Trueness Verification Plan indicate significant differences among routine systems, highlighting the need for standardization efforts. The developed candidate RMP for serum theophylline serves as a precise reference baseline for standardizing clinical systems and assigning values to reference materials.

Development and evaluation of a candidate reference measurement procedure for detecting 17α-hydroxyprogesterone in dried blood spots using isotope dilution liquid chromatography tandem mass spectrometry

17α-Hydroxyprogesterone (17α-OHP) quantification in dried blood spots (DBS) is essential for newborn screening for congenital adrenal hyperplasia (CAH), which is challenging due to its low physiological concentration. The high false-positive rates of immunoassays necessitate the development of more accurate methods. Liquid chromatography tandem mass spectrometry (LC-MS/MS) offers increased specificity and sensitivity, yet standardized procedures for 17α-OHP measurement are required for clinical application. A candidate reference measurement procedure (cRMP) using isotope dilution LC-MS/MS was developed for 17α-OHP quantification in DBS. By utilizing stable isotope-labeled D8-17α-OHP as an internal standard, the cRMP was optimized, covering sample preparation, calibration, and LC-MS/MS analysis. The method performance was validated across several parameters, including precision, accuracy, specificity, detection limits, and matrix effects. Clinical applicability was further assessed through the establishment of reference intervals for healthy newborns. The developed cRMP exhibited a linear range of 1.00 to 80.00 ng/mL for 17α-OHP, with detection and quantification limits of 0.14 ng/mL and 0.52 ng/mL, respectively. Inter- and intraday precision demonstrated coefficients of variation within 1.27 to 5.69%. The recovery rates and matrix effects were well within acceptable limits, ensuring method reliability. Clinical application showed distinct reference intervals for healthy newborns that were unaffected by sex but influenced by weight and gestational age. This method significantly enhances CAH diagnostic accuracy in newborns, providing a valuable tool for clinical laboratories and improving newborn screening program standardization and traceability.

Application of the adaptive Monte Carlo method for uncertainty evaluation in the determination of total testosterone in human serum by triple isotope dilution mass spectrometry

The measurement uncertainty is a crucial quantitative parameter for assessing the reliability of the result. The study aimed to propose a new budget for uncertainty evaluation of a reference measurement procedure for the determination of total testosterone in human serum. The adaptive Monte Carlo method (aMCM) was used for the propagation of probability distributions assigned to various input quantities to determine the uncertainty of the testosterone concentration. The basic principles of the propagation and the statistical analysis were described based on the experimental results of the quality control serum sample. The analysis of the number of Monte Carlo trials was discussed. The procedure of validation of the GUM uncertainty framework using the aMCM was also provided. The number of Monte Carlo trials was 2.974 × 106 when the results had stabilized. The total testosterone concentration was 16.02 nmol/L, and the standard uncertainty was 0.30 nmol/L. The coverage interval at coverage probability of 95% was 15.45 to 16.62 nmol/L, while the probability distribution for testosterone concentration was approximately described by a Gaussian distribution. The validation of results was not passed as the expanded uncertainty result obtained by the aMCM was slightly lower, about 7%, than that by the GUM uncertainty framework with consistent results of the concentration.Graphical

Establishment and clinical application of a candidate reference measurement procedure for quantification of urinary vanillylmandelic acid and homovanillic acid using ID-LC-MS/MS method

Neuroblastoma (NB), an embryonic tumor of the autonomous nervous system, poses a significant threat to the health and lives of children. Accurate measurement of vanillylmandelic acid (VMA) and homovanillic acid (HVA) in human urine is crucial for screening and diagnosis of NB. Although various laboratories have developed liquid chromatography tandem mass spectrometry (LC-MS/MS) method to detect VMA and HVA, the comparability between the results obtained from different laboratories and methods was poor. The absence of reference method for VMA and HVA hinders the standardization of their measurements. Therefore, a candidate reference measurement procedure (cRMP) based on isotope dilution LC-MS/MS (ID-LC-MS/MS) for the detection of VMA and HVA in human urine was established. Urine samples were spiked with VMA-d3 and HVA-d5 as internal standards and extracted using a protein precipitation method. The cRMP exhibited desirable precision with the total imprecision below 5 %. The accuracy of this cRMP was demonstrated by the high analytical recovery (98.64 % - 102.22 % and 98.41 % - 100.97 % for VMA and HVA, respectively), and comparability between different reference systems. The limit of detection for HVA and VMA were 15.625 ng/mL and 3.906 ng/mL, respectively; the quantification limits were 62.5 ng/mL and 7.813 ng/mL, respectively, which can meet the clinical detection requirements. The linear range was from 78.125 ng/mL to 20 μg/mL. Specificity evaluations showed no corresponding interference from structurally similar analogs. In conclusion, we have established a cRMP based on ID-LC-MS/MS for the measurement of VMA and HVA in urine samples, demonstrating well-defined method performance including accuracy, precision, and specificity. This newly established cRMP is suitable for routine assay standardization and evaluation of clinical samples. Furthermore, this method has the potential to significantly enhance the diagnostic accuracy for neuroblastoma.

Transferability and degree of harmonization of an LC-MS based reference measurement procedure for apolipoproteins in a network of calibration laboratories

Transferability and degree of harmonization of an LC-MS based reference measurement procedure for apolipoproteins in a network of calibration laboratories

Establishment, performance evaluation, and influence factors analysis of the α-amylase reference measurement procedure

Establishment, performance evaluation, and influence factors analysis of the α-amylase reference measurement procedure