Rectangular Dielectric Resonator Antenna Research Articles

Bilateral rectangular shape dielectric resonator antenna coupled with offset microstrip lines for wideband circular polarization

SummaryIn this work, an offset microstrip line coupled bilateral rectangular‐shaped dielectric resonator antenna (RDRA) is designed for broadband circular polarization (CP), which is fabricated and experimentally verified. The vertical microstrip is added in an offset position to generate orthogonal modes and the fundamental modes TEx111 and TEy111. The generation of orthogonal modes designates the antenna structure as a CP antenna with orthogonal modes. Moreover, the location of the microstrip feed arrangement is used to control the polarization state in the proposed work. In the proposed design, the simulated and hand‐measured input impedance bandwidth(|S11| ≤ −10 dB) obtained is 32.6% (3.53–4.9 GHz) and 33.2% (3.56–4.98 GHz), respectively, whereas the simulated and measured axial ratio (AR ≤ 3 dB) shows 16.1% (3.71–4.36 GHz) and 17.03% (3.7–4.39 GHz) of axial ratio bandwidth, respectively. This design shows a consistent radiation pattern and good average gain, with acceptable agreement between simulation and hand‐measured results. The simulated result shows 94% radiation efficiency in the working frequency range.

A compact dielectric resonator antenna with wideband circular polarization characteristics for C and X‐band applications

AbstractA wideband circularly polarized (CP) stacked rectangular dielectric resonator antenna (RDRA) is proposed in this article. The 3 dB axial ratio (AR) and 10 dB impedance bandwidth overlap of more than 66% is obtained. For increased bandwidth, the antenna comprises two dielectric resonators separated by an air gap. The upper dielectric layer is rotated at relative to the lower layer to obtain orthogonal modes for CP Both layers have dielectric constant . The rotation aids excitation of orthogonal modes , and in RDRA. The higher‐order modes generate left‐hand circular polarization at frequencies 6.75, 7.8, and 10.7 GHz, respectively. The upper layer consists of three holes giving a 10 dB impedance bandwidth of 66.7% from 6.52 to 11.02 GHz. The CP gain of 8.7, 6.8, and 6.4 dBi for 6.75, 7.8, and 10.7 GHz, respectively, is measured. The conformal orthogonal feeds enable a 72 3 dB AR bandwidth across the entire frequency band. The radiation efficiency is observed above 89 in the entire band (6.5–11 GHz). This work demonstrates a 66.7 overlap of 10 dB impedance and 3 dB AR bandwidth along with high gain in a single design which is suitable for 5G applications in C‐band as well as other X‐band applications.

Frequency-Reconfigurable Millimeter-Wave Rectangular Dielectric Resonator Antenna.

This paper introduces an innovative and cost-effective approach for developing a millimeter-wave (mmWave) frequency-reconfigurable dielectric resonator antenna (DRA), which has not been reported before. The antenna integrates two rectangular DRA elements, where each DRA is centrally fed via a slot. A strategically positioned PIN diode is employed to exert control over performance by modulating the ON-OFF states of the diode, thereby simplifying the design process and reducing losses. In the OFF state, the first DRA, RDRA-I, exclusively supports the TE311 resonance mode at 24.3 GHz, offering a 2.66% impedance bandwidth and achieving a maximum broadside gain of 9.2 dBi. Conversely, in the ON state, RDRA-I and RDRA-II concurrently operate in the TE513 resonance mode at 29.3 GHz, providing a 2.7% impedance bandwidth and yielding a high gain of up to 11.8 dBi. Experimental results substantiate that the proposed antenna presents an attractive solution for applications necessitating frequency-reconfigurable and high-performance mmWave antennas in 5G and Beyond 5G (B5G) communication systems.

Compact quad element dual band high gain MIMO rectangular dielectric resonators antenna for 5G millimeter wave application

In this article, a compact dual-band quad-port Multiple Input Multiple Output (MIMO) Rectangular Dielectric Resonator Antenna (RDRA) with a defected connected ground Geometry (DCGG) for 5G millimeter-wave (mm-wave) application is presented. The antenna is operating at 24 GHz to 32 GHz frequency range. The antenna configuration comprises four identical rectangular microstrip radiators mounted on an RT Duroid 5880 substrate (20 × 20 × 0.254) mm3. To enhance bandwidth, each radiator is equipped with both rectangular and circular-shaped ring slots. To improve the performance of the 4 port MIMO antenna, RDRAs are placed over each radiator and optimized. The MIMO RDRs exhibit dual-band with 4.24 GHz and 0.46 GHz bandwidths. The MIMO RDRA achieves exceptional isolation (>27 dB), high gain (8.24 dB), and more than 94 % radiation efficiency. The diversity parameters exhibit a low Envelope Correlation Coefficient (ECC) of 0.0006, and a high Diversity Gain (DG) of 9.97 dB is achieved, highlighting the effectiveness of the antenna system in providing diversity reception and improving communication reliability in challenging environments. Hence, the proposed MIMO antenna is compact, making it suitable for integration into small 5G devices or systems where space is limited, such as IoT devices, mobile phones, or small base stations at mm-wave frequency bands.

A wideband high-gain dielectric resonator antenna based on mullite microwave dielectric ceramics

In this paper, the high-quality factor mullite microwave dielectric ceramic is employed to introduce in dielectric resonator antenna (DRA). The microwave dielectric properties of ɛr ∼ 5.8, Q × f ∼ 31 240 at 9.66 GHz, and loss tangent tanδ = 1/Q ∼ 2.7 × 10−4 can be obtained by the solid-state reaction method in mullite microwave dielectric ceramic sintered at 1700 °C. On this basis, the resonant modes of the proposed broadband high-gain rectangular DRA are analyzed by using a dielectric waveguide theoretical model and the antenna performance is evaluated by a commercial CST Microwave Studio 2021® software. It has been found that the proposed rectangular DRA can provide a broad bandwidth of 35.9%, a maximum gain of 10 dBi at 3.61 GHz, and a radiation efficiency of 90% in the range of 3.13–4.42 GHz. For demonstration, adequate consistency between the simulation results and the measurement results was achieved. The proposed DRA has great application potential and value in 5G communication scenarios requiring wideband and high-gain antenna.

Four-Element Biodegradable Substrate-Integrated MIMO DRA with Radiation Diversity

This article presents a four-element directional multiple input multiple output (MIMO) rectangular dielectric resonator antenna (RDRA) equipped with strategically placed copper reflector plates to enhance port isolation. This design aims to achieve an extended coverage range without compromising the coverage area. The proposed MIMO antenna is 3D printed using biodegradable polylactic acid to ensure mechanical robustness and then integrated with the substrate to prevent mis-mounting issues. The proposed design exhibits good MIMO characteristics, registering a 3-GHz bandwidth (4–7 GHz) for |S11|≤-10 dB and a minimum radiation gain of 7 dBi for all four RDRAs. The antenna demonstrates a rotation of radiation patterns for different ports, thus enabling beam formation in specific directions. With a beam width of 71.2˚, the antenna covers all directions without any fade zones. The proposed 3D printed antenna offers simplicity, strong MIMO properties, and practicality for wireless communication systems, making it suitable for industrial, scientific, and medical band applications.

5G millimeter‐wave MIMO DRAs with reduced mutual coupling

AbstractA novel simple decoupling technique is proposed to suppress the mutual coupling of a millimeter‐wave multiple‐input‐multiple‐output dielectric resonator antenna (DRA). The design to be decoupled consists of two microstrip‐line fed rectangular DRAs placed side‐by‐side on an RT‐Duroid substrate and operates near 26 GHz. First, the DRAs are placed at an appropriate separation distance to avoid any close coupling. Second, to reduce coupling further, a set of square ring cell loaded slot is employed on the ground plane in between the DRAs. These two arrangements together, potentially reduce the mutual coupling between the DR elements and substantially improves the in‐band isolation from 14 to 23 dB (min)/34 dB (max) between them. The design is very simple, compact, and easy to fabricate. The model is prototyped and characterized to demonstrate its feasibility for operation. This can be a suitable technique for fifth‐generation compact handheld microwave devices.

Edge Hole Effect on Isolation of UWB MIMO RDRA for 5G Outdoor Applications

For 5G sub-6 GHz outdoor applications, a highly isolated two-port rectangular dielectric resonator antenna (RDRA) with UWB MIMO is presented in this research. For isolation enhancement purposes at the lower frequency band (2.27 GHz-2.62 GHz), a longitudinal slot is inserted at the ground plane. For isolation enhancement at the higher frequency band (3.9 GHz-5.73 GHz), an edged hole is inserted in the RDRA. Investigations are conducted on the impacts of slotted ground as well as edged hole radius on isolation. The orthogonal feeding scheme of UWB MIMO RDRA considering both edged hole and slotted ground plane effects are investigated. For the edged hole MIMO RDRA with a slotted ground plane, isolation is better than -24.7 dB at a higher frequency band and is better than -15.5 dB at a lower frequency band. This isolation improvement is explained by the surface current density distribution. The use of an edged hole RDRA and an aperture-coupled orthogonal feeding allows UWB bandwidth and good efficiency performances on the 5G operating bands. To justify the MIMO performance, the envelope correlation coefficient (ECC) and diversity gain (DG) are applied.

Modified Microstrip Feed Hybrid Rectangular Dielectric Resonator Antenna for Wireless Tri-Band Applications

Abstract This article reports the Modified Microstrip Feed Hybrid Rectangular Dielectric Resonator Antenna (RDRA). The proposed structure has a ground plane with a plus-shaped slot on an FR4 substrate with a height of 1.6 mm and dimensions of 38 mm x 35 mm. The proposed Dielectric resonator antenna is made of a material with 10 as its dielectric constant, and the dimensions of the DR are 19 x 20 x 18 mm3. The DR is connected to a modified microstrip feed with an octagonal ring through the plus-shaped slot in the ground. The proposed structure operates in frequencies from 2.60 GHz - 2.74 GHz, 3.12 GHz - 3.37 GHz, and 4.25 GHz - 4.37 GHz. The resonant frequency of the final proposed RDRA is 2.68 GHz, 3.26 GHz, and 4.31 GHz, which covers WLAN, WIMAX and Wireless Avionics Intra-Communications (WAIC) applications, respectively. The entire structure was simulated using the CST microwave studio. The simulated results agree with the measured results and both are presented. The compact size, stable radiation pattern and reasonable gain make this antenna suitable for the proposed applications.

A Multiband Millimeter-Wave Rectangular Dielectric Resonator Antenna with Omnidirectional Radiation Using a Planar Feed.

In this study, a millimeter-wave (mmWave) dielectric resonator antenna (DRA) with an omnidirectional pattern is presented for the first time. A key feature of the proposed design is the utilization of a planar feed network to achieve omnidirectional radiation from a rectangular DRA, which has not been reported previously in the open literature. In addition, the proposed antenna offers multiband operation with different types of radiation patterns. The degenerate TE121/TE211 modes were excited at 28.5 GHz with an overall internal electromagnetic field distribution that was similar to that of the HEM21δ mode of a cylindrical DRA. The achieved omnidirectional bandwidth and gain were 1.9% and 4.3 dBi, respectively. Moreover, broadside radiation was achieved by exciting the TE111 fundamental mode at 17.5 GHz together with the resonance of the feeding ring-slot at 23 GHz. The triple-band operation offers a highly versatile antenna that can be utilized in on-body and off-body communications. Furthermore, the proposed design was validated through measurements, demonstrating good agreement with simulations.

Analysis of dielectric resonator antenna using natural fiber reinforced polymer composites

This work aims to demonstrate the viability of replacing natural fiber reinforced polymer composites for hard ceramics in millimeter-wave dielectric resonator antennas (DRA). The dielectric characteristics of three novel natural fiber reinforced polymer composites were determined using the Lichtenecker logarithmic mixing law. Using two commercial antenna design software packages, CST Studio and ANSYS HFSS, the resulting dielectric characteristics were utilized to study a probe-fed rectangular DRA. Natural fiber-reinforced polymer-based DRAs offer a wider bandwidth than ceramic-based DRAs. Close coupling is obtained by the three natural fiber-reinforced polymer-based antennas and the ceramic DRA. In all cases, the impedance bandwidths observed are the consequence of quasi-TM111 mode radiation. HFSS studies indicate that the resonance frequency of the natural fiber reinforced polymer based DRAs is roughly 75 percent higher than that of the ceramic DRA. CST results indicate that the resonance frequency of the natural fiber polymer-based DRA is approximately 88 percent higher than that of the ceramic DRA. Natural fiber reinforced Polymer-based DRAs have three times the −10 dB impedance bandwidth of ceramic-based DRAs.

Frequency reconfigurable wideband rectangular dielectric resonator antenna for sub-6 GHz applications with machine learning optimization

This work presents frequency reconfigurable Wideband Rectangular Dielectric Resonator Antenna (RDRA) using a Machine Learning (ML) approach for 5G (Sub-6 GHz) applications. The concept of ML is integrated with reconfigurable DRA for the first time. A novel approach has been proposed to obtain wideband and frequency reconfigurability. Frequency reconfigurability is achieved electronically (PIN diode switches) and operates in four different configurations, offering a maximum of 76.84 % wide tuning range. Hybrid structure and higher order mode TE111 and TE211 modes excitation is responsible for wideband operation. The Extreme Gradient Boosting (XGB) ML algorithm provides more than 90 % accuracy in all configurations for S11 prediction.

Defected ground structure based compact UWB dielectric resonator antennas with enhanced bandwidth

Abstract This article introduces two new compact ultra-wide band (UWB) rectangular dielectric resonator antennas (RDRAs) with enhanced bandwidth (BW), gain, and directivity. The RDRAs are designed at 10 GHz resonant frequency. The proposed RDRAs are compactly designed using resonating dielectric material (RDM) of Alumina_96 pct (ε r = 9.4, tanδ = 0.006) with overall dimensions of 30 × 20 × 4.6 mm3. The RDMs are mounted on FR4 substrate (ε r = 4.4, tanδ = 0.02) with defected ground structure (DGS). The DGS are comprised of rectangular and circular ring slots on it. These compact DGS-RDRAs provides enhanced BW. Prototypes of the two suggested RDRAs are fabricated. The fabricated RDRAs are validated by experimental set-ups. The RDRA with rectangular-ring slot DGS provides impedance BW (S 11 < −10 dB) of 33.97 % (8.6658–12.071 GHz). The impedance BW of the other RDRA is 27.97 % (9.08–11.869 GHz). The rectangular-ring slotted RDRA offers radiation efficiency and peak realized gain of 86.4 % and 6.27 dBi, respectively within the band of operating frequencies. The radiation efficiency and realised gain of circular-ring slotted RDRA are 86.18 % and 5.9 dBi, respectively. Good agreements are achieved in between the simulated results and measured results. The results are compared with some recently developed antennas available in literature. The comparison shows that the proposed RDRAs can be suitable candidate for various X-band applications such as satellite downlinks, synthetic aperture radar, weather monitoring by military and some government organizations.

A Low-Profile Compact Broadband CP DRA for RF Energy Harvesting Applications

In this letter, a low-profile circularly polarized (CP) chamfered rectangular dielectric resonator antenna (RDRA) is designed and investigated for radio frequency energy harvesting (RFEH) applications. The proposed modified RDRA comprises of dielectric resonator (DR) made up of Alumina material (ε r = 9.9) mounted on the PEC ground plane. Dual unequal triangular-shaped vertical slits are engraved on the rectangular DR for generating the orthogonal modes with CP characteristics. The optimized antenna offers an impedance bandwidth (IBW) of 51.4% (2.25–3.81 GHz) and axial ratio bandwidth (ARBW) of 14.8% (3.25–3.77 GHz), respectively. The peak realized gain and maximum radiation efficiency are 7.18 dBi and 97.8% in desired frequency bands. Due to the wide impedance and AR bandwidths with realized gain and radiation efficiency, the optimized antenna is suitable for integration with a rectifier circuit for RF energy harvesting applications. A rectifier circuit with a single shunt diode topology is also designed for rectification purposes. The rectifier achieved 67.16% RF-DC power conversion efficiency (PCE) at 3.5 GHz and 5dBm input power. At 0dBm input power, the rectifier achieved 60.26% PCE. The effective input power range, during which the PCE maintains above 50%, is calculated to be 15.2 dBm from −3.5 to 11.7 dBm.

A Frequency Tunable Dielectric Resonator Antenna with Reduction of Cross Polarisation for Wi MAX and Sub 6 GHz 5G Applications

A frequency Tunable (mechanical tuning) Linearly Polarized (TLP) rectangular Dielectric Resonator Antenna(DRA) coupled with a horizontal/vertical-slot and excited with circular-ring type feed is investigated in this article.The frequency tunability (mechanical tuning) is achieved by the rotation of slot at different angles of the proposedstructure. Hence, two linearly polarized antennas have been proposed for different frequency bands such as Wi-MAX and Sub-6 GHz/5G, respectively, using slot variations (named as DRA-1 and DRA-2). TE 11δ mode has been excited in both the DRAs and confirmed by orientation of electric field inside the rectangular DRA. The measured -10 dB input impedance bandwidths of DRA-1 offer 21.60 % being centered at 2.87 GHz and the separation of co-polarized and cross-polarized field levels is above -24 dB in the broadside direction (xz-plane). Whereas DRA-2 offers measured -10 dB input impedance bandwidths of 23.03% being centered at 3.56 GHz having a separation of co-polarized and cross-polarized field levels are above -23 dB in the broadside direction (xz-plane). In addition, the proposed DRA-1 and DRA-2 show a maximum gain of 5.23 dBi and 4.75 dBi in broadside direction, respectively.

1-D Wideband Phased Dielectric Resonator Antenna Array With Improved Radiation Performance Using Characteristic Mode Analysis

A 1-D wideband phased array of the rectangular ring dielectric resonator antenna (RRDRA) is presented for millimeter-wave applications. By using the characteristic mode analysis, it is found that the unwanted higher order mode (HOM) of the RRDRA results in severe gain degradation and high cross polarization when the array scans. To remedy the problem, each RRDRA is loaded with a pair of silver strips. They can suppress the unwanted HOM and enable good scanning performance in a wide frequency range. To demonstrate the idea, a 1×4 phased RRDRA array was designed, fabricated and measured for the licensed millimeter-wave bands (24.25–29.5 GHz). Reasonable agreement between the measured and simulated results is observed.

A new planar feeding method of dielectric rod antenna using dielectric resonator

This article proposes a new method for exciting surface waves in dielectric rod antennas using dielectric resonator antennas. The method involves housing a rectangular dielectric resonator antenna with a dielectric constant of 10.2 inside a hollow cylindrical dielectric rod antenna made of Teflon. By exciting the {TE}_{111}^{y} and {TE}_{113}^{y} modes of the dielectric resonator antenna, a surface wave can be launched along the Teflon tube. This method offers the advantage of integrating the dielectric rod antenna with planar circuits, where maximum radiation in the direction normal to the board is desirable. Compared to other planar feeding methods, this technique leads to lower back lobe and sidelobe levels. I fabricated the proposed structure and conducted tests to measure its performance. The measured results show an impedance bandwidth of 22% from 7.35 to 9.4 GHz and a maximum gain of 14 dB. Additionally, the simulated radiation efficiency of the proposed antenna in the entire band is above 90%.

Novel corrugated rectangular dielectric resonator antenna with wide half power beam width

ABSTRACT In this work, a dielectric resonator antenna element is corrugated in a specific way, which led to increase its half power beam width (HPBW). The HPBW of the antenna is investigated for different values of corrugation depth and it has been concluded that HPBW can be increased by increasing this depth. By embedding periodic grooves in the DRA walls, it is possible to adjust the radiation intensity ratio of the upper wall to the side walls. By increasing this ratio, the HPBW of the antenna can be increased. To confirm the concept of beam widening method, a prototype of the corrugated DRA is fabricated and measured. Measured results show an impedance bandwidth of 23% (3.8–4.8 GHz). The measured E- and H-plane HPBWs at 4.1 GHz are 137° and 123°, respectively. Measured and simulated results are in a good agreement.

DESIGN OF A UAV BLADE MONOPOLE WITH THE USE OF DIFFERENT RTADIATING ELEMENTS AND SIMULATION OF DRA ANTENNA

Because of its small size, light weight, and aerodynamic design that causes the least amount of drag blade monopole antennas are favored for usage in airborne applications. Consequently, their radiation patterns are unipolar and produce deep nulls in the upward direction. Such patterns will cause severe blind spots for the aircraft above and below this plane, which is undesirable for avionics networks. [1] To solve this problem, a dielectric resonator antenna (DRA) is attached to the blade antenna and thus a different design is formed. In this paper a rectangular DRA is used to illustrate the main idea.The antenna is housed inside the aerodynamically designed radome to reduce air drag (large dome-shaped structures which protect the radars from the bad weather conditions but at the same time allow the electromagnetic signals to be received by the radar without any distortion or attenuation). [11] An air core coil is also provided for DC grounding proposes. The antenna configuration is first optimized using HFSS based Ansys Electronics Desktop Student 2021 R2 simulation software and latter practically implemented. The comparison of simulated results is also presented in this paper.

A Novel Low‐profile Rectangular Dielectric Resonator Antenna with enhanced gain for 5G New Radio band applications

AbstractA wideband low‐profile chamfered rectangular dielectric resonator antenna (RDRA) with high gain is proposed for sub‐6 GHz 5G new radio band applications. RDRA is excited with microstrip cross‐slot aperture coupling which is employed on the substrate. The dielectric resonator antenna with low‐profile produces unwanted back radiation. The reflector placed at the bottom side of the RDRA is accountable for gain improvement on boresight direction by reducing back radiation. Slits, introduced on the copper layer, help to control the phase difference between direct waves and reflected waves. A rectangular stub is added to microstrip feed to enhance the impedance matching between excitation port and the antenna. The proposed antenna offers 2.74–4.35 GHz impedance bandwidth and 9.1 dBi peak gain. The proposed design is fabricated and experimentally verified.