Real-time Wireless Data Transmission Research Articles

Smart Capsule for Targeted Detection of Inflammation Levels Inside the GI Tract.

Effective management of Inflammatory Bowel Disease (IBD) is contingent upon frequent monitoring of inflammation levels at targeted locations within the gastrointestinal (GI) tract. This is crucial for assessing disease progression and detecting potential relapses. To address this need, a novel single-use capsule technology has been devised that enables region-specific inflammation measurement, thereby facilitating repeatable monitoring within the GI tract. The capsule integrates a pH-responsive coating for location-specific activation, a chemiluminescent paper-based myeloperoxidase (MPO) sensor for inflammation detection, and a miniaturized photodetector, complemented by embedded electronics for real-time wireless data transmission. Demonstrating linear sensitivity within the physiological MPO concentration range, the sensor is capable of effectively identifying inflammation risk in the GI fluid. Luminescence emitted by the sensor, proportional to MPO concentration, is converted into an electrical signal by the photodetector, generating a quantifiable energy output with a sensitivity of 6.14 µJ/U.ml-1. The capsule was also tested with GI fluids collected from pig models simulating various inflammation states. Despite the physiological complexities, the capsule consistently activated in the intended region and accurately detected MPO levels with less than a 5% variation between readings in GI fluid and a PBS solution. This study heralds a significant step towards minimally invasive, in situ GI inflammation monitoring, potentially revolutionizing personalized IBD management and patient-specific therapeutic strategies.

Coupling charge pump and BUCK circuits to efficiently enhance the output performance of triboelectric nanogenerator

Triboelectric nanogenerator (TENG) faces significant challenges in practical applications because of its low output charge density and high matching impedance, and the development of its energy management circuits is hindered by high initial device requirements, large circuit size and poor portability. In this work, we propose a simple, efficient and versatile energy management strategy that two-stage amplification of TENG output performance by coupling a charge pump circuit with a BUCK circuit. By implementing the energy management strategy, the charge output per cycle of an ordinary TENG can be increased by more than 40 times, resulting in a power density of 25.2 mWm−2 and a total energy transfer efficiency of exceeding 88% in constant mode. At a working frequency of 1 Hz, the TENG can charge a 1000 μF capacitor to 5.04 V in 240 s and store the energy of more than 12.72 mJ, of which represents an 848-fold increase in stored energy compared to using TENG directly. Remarkably, this TENG device exhibits exceptional an average power of 100.7 μW/Hz, setting a new record for devices with smaller TENG size (< 50 cm2) or limited PM circuit size (< 10 cm2). Moreover, an ordinary TENG can continuously power a wireless sensor by integrating the portable power management circuit, facilitating real-time wireless data transmission. This study is of great significance for the practical application of the TENG power supply in the sensor network of the Internet of Things and for expanding the application range of the TENG.

IoT based Optimal Liquid Metal Pipeline Damage Detection Using Hybrid Soft Computing Techniques

The pipeline plays an important role in transporting liquid metals over long distances. However, due to the harsh conditions on the construction site, the pipelines are always exposed to structural damage due to corrosion, damage, etc. These pipelines are often vulnerable to natural and third-party events such as explosions, earthquakes, explosions, drilling and vehicle traffic. Methods for monitoring liquid metal pipes include the use of continuous pipe assessments and pipe integration management systems. One of the biggest challenges faced by liquid metal pipeline system in the past has been the real-time monitoring of seamless pipes at certain locations. Previous studies of liquid metal pipeline monitoring have rarely focused on real-time wireless data transmission and data monitoring in the Internet of Things (IoT) operating system. In this paper, we propose an optimal liquid metal pipeline damage detection using IoT sensor platform and hybrid soft computing techniques. The proposed work consists of two fold systems such as data collection and data processing unit. In data collection unit, we utilize IoT sensors deployment with the multimedia sensors to gather liquid metal pipeline images which improve the detection accuracy. In data processing unit, we introduce a hybrid cat hunting based neural network (hybrid CHNN) to detect and localize the pipeline damages/cracks to avoid unwanted leakage and accidents. Finally, we evaluate the performance of our proposed hybrid CHNN detector with the different test samples and the simulation results are compared with the existing stateof- art pipeline damage detectors in terms of accuracy, precision, Recall and F-measure.

Wearable soft electrochemical microfluidic device integrated with iontophoresis for sweat biosensing

A soft and flexible wearable sweat epidermal microfluidic device capable of simultaneously stimulating, collecting, and electrochemically analyzing sweat is demonstrated. The device represents the first system integrating an iontophoretic pilocarpine delivery system around the inlet channels of epidermal polydimethylsiloxane (PDMS) microfluidic device for sweat collection and analysis. The freshly generated sweat is naturally pumped into the fluidic inlet without the need of exercising. Soft skin-mounted systems, incorporating non-invasive, on-demand sweat sampling/analysis interfaces for tracking target biomarkers, are in urgent need. Existing skin conformal microfluidic-based sensors for continuous monitoring of target sweat biomarkers rely on assays during intense physical exercising. This work demonstrates the first example of combining sweat stimulation, through transdermal pilocarpine delivery, with sample collection through a microfluidic channel for real-time electrochemical monitoring of sweat glucose, in a fully integrated soft and flexible multiplexed device which eliminates the need of exercising. The on-body operational performance and layout of the device were optimized considering the fluid dynamics and evaluated for detecting sweat glucose in several volunteers. Furthermore, the microfluidic monitoring device was integrated with a real-time wireless data transmission system using a flexible electronic board PCB conformal with the body. The new microfluidic platform paves the way to real-time non-invasive monitoring of biomarkers in stimulated sweat samples for diverse healthcare and wellness applications.

Millimeter-Wave Multiplexed Wideband Wireless Link Using Rectangular-Coordinate Orthogonal Multiplexing (ROM) Antennas

This paper is the first demonstration of multiplexed wideband data transmission in the millimeter-wave range using rectangular-coordinate orthogonal multiplexing (ROM) antennas. This spatial wireless multiplex communication method can be applied at several hundred GHz for further improvements in the data rate because much wider bandwidth is available and this multiplexing method does not require any signal processing. The multiplexing is achieved through the spatial eigenmodes of a novel antenna based on a rectangular coordinate system and magic-T which eliminates the need for computational signal processing efforts. The aperture distributions of these spatial eigenmodes are designed to have different polarities to avoid crosstalk and operate over a wide bandwidth range. We demonstrate their performance with four eigenmodes, achieving crosstalk between modes below −37.8 dB over a 14.6% relative bandwidth (57–66 GHz). We have introduced these antennas on a photonics-enabled real-time wireless data transmission, transmitting over two channels simultaneously, without any signal processing at the transmitter (multiplex) or the receiver (demultiplex). The two multiplexed channels show a total data rate up to 9.0 Gbps at most (5.875 Gbps and 3.125 Gbps for each channel) limited by the bandwidth of the low noise amplifiers at the receiver. The measured bit error rate (BER) is below the forward error correction (FEC) limit.

Wearable Sensory Apparatus for Real-Time Feedback in Wearable Robotics

We describe the Wearable Sensory Apparatus (WSA) System, which has been implemented and verified in accordance with the relevant standards. It comprises the Inertial Measurement Units (IMUs), real-time wireless data transmission over Ultrawideband (UWB), a Master Unit and several IMU dongles forming the Wireless Body Area Network (WBAN). The WSA is designed for, but is not restricted to, wearable robots. The paper focuses on the topology of the communication network, the WSA hardware, and the organization of the WSA firmware. The experimental evaluation of the WSA incorporates the confirmation of the timing using the supply current WSA profile, measurements related to determining the less error prone position of the master device on the backpack, measurements of the quality of the data transfer in a real environment scenario, measurements in the presence of other microwave signals, and an example of raw IMU signals during human walking. Placement of the master device on the top of the backpack was found to be less error prone, with less than 0.02% packet loss for all the IMU devices placed on different body segments. The packet loss did not change significantly in public buildings or on the street. There was no impact of Wi-Fi bands on the WSA data transfer. The WSA hardware and firmware passed conformance testing in a certified lab. Most importantly, the WSA performed reliably in the laboratory and in clinical tests with exoskeletons and prostheses.

A Localization and Navigation Method for an In-Pipe Robot in Water Distribution System Through Wireless Control Towards Long-Distance Inspection

In this paper, we propose an operation procedure for our previously developed in-pipe robotic system that is used for water quality monitoring in water distribution systems (WDS). The proposed operation procedure synchronizes a developed wireless communication system that is suitable for harsh environments of soil, water, and rock with a multi-phase control algorithm. The new wireless control algorithm facilitates smart navigation and near real-time wireless data transmission during operation for our in-pipe robot in WDS. The smart navigation enables the robot to pass through different configurations of the pipeline with long inspection capability with a battery in which is mounted on the robot. To this end, we have divided the operation procedure into five steps that assign a specific motion control phase and wireless communication task to the robot. We describe each step and the algorithm associated with that step in this paper. The proposed robotic system defines the configuration type in each pipeline with the pre-programmed pipeline map that is given to the robot before the operation and the wireless communication system. The wireless communication system includes some relay nodes that perform bi-directional communication in the operation procedure. The developed wireless robotic system along with operation procedure facilitates localization and navigation for the robot toward long-distance inspection in WDS.

Highly Efficient Front End Direct Conversion Receiver for 28-GHz Wireless Access Point

The manuscript presents the design and characterization of a wideband front-end receiver, based on hollow waveguide technology, for the wireless access point (WAP) applications. The Ka-band receiver is comprised of a low-loss beam-switching antenna network (BSAN) with two-dimensional (2D) scanning property. For demodulation, the receiver uses an efficient six-port network (SPN) that is composed of four 90° hybrid couplers and a 90° phase shifter. To suppress the phase imbalance on the entire band of interest, 27 GHz to 33 GHz, a frequency-independent phase shifter with a minimum phase error is suggested. The SPN receiver is integrated with antenna-in-package in waveguide technology to decrease the insertion losses and noise levels at the first stages. To determine the SPN phase errors, a theoretical and experimental analysis of real-time wireless data transmission utilizing phase-shift keying (PSK) and quadrature amplitude modulated (QAM) signal is conducted. Besides, channel capacity along with beamformer influence on channel performance improvement are determined.

Compact Integrated Full-Duplex Gap Waveguide-Based Radio Front End For Multi-Gbit/s Point-to-Point Backhaul Links at E-Band

This paper presents the design and realization of a high data rate radio front-end module for point-to-point backhaul links at E-band. The design module consists of four vertically stacked unconnected metal layers without any galvanic and electrical contact requirements among the building blocks, by using gap waveguide technology. The module components are a high-gain array antenna, diplexer, and circuitry consisting of a transmitter (Tx) and a receiver (Rx) monolithic microwave integrated circuits (MMICs) on a carrier board, which is successfully integrated into one package with a novel architecture and a compact form. The diplexer consists of two direct-coupled cavity bandpass filters with channels at 71–76 GHz and 81–86 GHz with a measured return loss of 15 dB and an isolation greater than 50 dB. A wideband $16\times 16$ slot array antenna with a measured gain of more than 31 dBi is used to provide high directivity. The measured results show that the packaged transmitter provides a conversion gain of 22 and 20 dB at 76 and 86 GHz, respectively, with an output power of 14 and 16 dBm at 1-dB gain compression point, at the same frequencies. The packaged receiver shows an average conversion gain of 20 dB at 71–76-GHz and 24 dB at 81–86-GHz bands. A real-time wireless data transmission is successfully demonstrated with a data rate of 8 Gbit/s using 32-quadrature amplitude modulated signal over 1.8-GHz channel bandwidth with spectral efficiency of 4.44 bit/s/Hz. The proposed radio front end provides the advantages of low loss, high efficiency, compact integration, and a simple mechanical assembly, which makes it a suitable solution for small-cell backhaul links.

DNA Nanotweezers and Graphene Transistor Enable Label-Free Genotyping.

Electronic DNA-biosensor with a single nucleotide resolution capability is highly desirable for personalized medicine. However, existing DNA-biosensors, especially single nucleotide polymorphism (SNP) detection systems, have poor sensitivity and specificity and lack real-time wireless data transmission. DNA-tweezers with graphene field effect transistor (FET) are used for SNP detection and data are transmitted wirelessly for analysis. Picomolar sensitivity of quantitative SNP detection is achieved by observing changes in Dirac point shift and resistance change. The use of DNA-tweezers probe with high-quality graphene FET significantly improves analytical characteristics of SNP detection by enhancing the sensitivity more than 1000-fold in comparison to previous work. The electrical signal resulting from resistance changes triggered by DNA strand-displacement and related changes in the DNA geometry is recorded and transmitted remotely to personal electronics. Practical implementation of this enabling technology will provide cheaper, faster, and portable point-of-care molecular health status monitoring and diagnostic devices.

Epidermal Microfluidic Electrochemical Detection System: Enhanced Sweat Sampling and Metabolite Detection.

Despite tremendous recent efforts, noninvasive sweat monitoring is still far from delivering its early analytical promise. Here, we describe a flexible epidermal microfluidic detection platform fabricated through hybridization of lithographic and screen-printed technologies, for efficient and fast sweat sampling and continuous, real-time electrochemical monitoring of glucose and lactate levels. This soft, skin-mounted device judiciously merges lab-on-a-chip and electrochemical detection technologies, integrated with a miniaturized flexible electronic board for real-time wireless data transmission to a mobile device. Modeling of the device design and sweat flow conditions allowed optimization of the sampling process and the microchannel layout for achieving attractive fluid dynamics and rapid filling of the detection reservoir (within 8 min from starting exercise). The wearable microdevice thus enabled efficient natural sweat pumping to the electrochemical detection chamber containing the enzyme-modified electrode transducers. The fabricated device can be easily mounted on the epidermis without hindrance to the wearer and displays resiliency against continuous mechanical deformation expected from such epidermal wear. Amperometric biosensing of lactate and glucose from the rapidly generated sweat, using the corresponding immobilized oxidase enzymes, was wirelessly monitored during cycling activity of different healthy subjects. This ability to monitor sweat glucose levels introduces new possibilities for effective diabetes management, while similar lactate monitoring paves the way for new wearable fitness applications. The new epidermal microfluidic electrochemical detection strategy represents an attractive alternative to recently reported colorimetric sweat-monitoring methods, and hence holds considerable promise for practical fitness or health monitoring applications.

Wearable Flexible and Stretchable Glove Biosensor for On-Site Detection of Organophosphorus Chemical Threats.

A flexible glove-based electrochemical biosensor with highly stretchable printed electrode system has been developed as a wearable point-of-use screening tool for defense and food security applications. This disposable-mechanically robust "lab-on-a-glove" integrates a stretchable printable enzyme-based biosensing system and active surface for swipe sampling on different fingers, and is coupled with a compact electronic interface for electrochemical detection and real-time wireless data transmission to a smartphone device. Stress-enduring inks are used to print the electrode system and the long serpentine connections to the wireless electronic interface. Dynamic mechanical deformation, bending, and stretching studies illustrate the resilience and compliance of the printed traces against extreme mechanical deformations expected for such on-glove sampling/sensing operation. An organophosphorus hydrolase (OPH)-based biosensor system on the index finger enables rapid on-site detection of organophosphate (OP) nerve-agent compounds on suspicious surfaces and agricultural products following their swipe collection on the thumb finger. The new wireless glove-based biosensor system offers considerable promise for field screening of OP nerve-agents and pesticides in defense and food-safety applications, with significant speed and cost advantages. Such "lab-on-a-glove" demonstration opens the area of flexible wearable sensors to future on-the-hand multiplexed chemical detection in diverse fields.

A Framework for Real-Time Source-Agnostic ECG Monitoring Using Artificial Intelligence

Background: Long-term, continuous real-time ECG monitoring for arrhythmia detection has been limited by challenges in development of comfortable, wearable ECG devices, real-time streaming and accurate, automated analysis. Our framework involves three independent but linked methodologies, involving ECG acquisition on a small wearable device, continuous wireless digital transfer of ECG data to a mobile device, and real-time arrhythmia-detection using artificial intelligence (AI). Methods: The current study was performed to compare our automated system against simultaneous ECG monitoring in a coronary care unit, using a standard patient monitoring system. ECGs were de-identified and randomised, and blinded R-R interval measurements were performed using manual digital callipers by three independent cardiologists. Results: ECG acquisition and continuous wireless transmission showed excellent data integrity and no significant dropouts. Storage and encryption of data was robust. The ECG signals acquired by our device appeared visually identical to the standard monitoring system. Agreement of R-R interval measurement between devices and observers was good, with RMSE and Bias at 26 and 6 ms, respectively. The rhythm comparison showed an accuracy of 93%. Conclusion: Our continuous, wearable ECG device with real time wireless data transmission to a mobile device provides robust data integrity, and good agreement compared with a standard ECG monitoring system. The framework provides a suitable platform for automated continuous arrhythmia detection on a smart phone, using AI.

Adaptive real time wireless data transmission using superposition coding with feedback of channel state information

High quality data transmission services are an important issue for broadband wireless access (BWA) systems. This paper deals with the design issues of a real-time wireless data transmission which provides unequal error protection (UEP) over an additive white Gaussian noise (AWGN) channel. Traditionally, transmission is made from a one bit stream at one level of power (for example, pulse amplitude modulation (PAM)) but using different techniques to exploit the available bandwidth. Using superposition coding, the real time data bit stream can be divided into two bit streams. The first bit stream represents the region of high priority (HP) while the second represents low priority (LP) region. These two bit streams are modulated separately, and superimposed together with two different levels of power to achieve the UEP at the receiver side. Feedback of the channel state information (CSI) is used by adaptive channel in the physical layer such that the current available bandwidth is used efficiently. In this proposed scheme, the same design metrics, namely time, bandwidth and power are used to increase the transmission efficiency. The performance of the proposed scheme is compared with the traditional, 2-PAM and 4-PAM schemes. Unlike the traditional schemes, the results show that our scheme provides a higher data rate at an acceptable bit error rate (BER) when the channel is in good condition. When channel quality is degraded, a reduced data rate is applied in contrast with the traditional schemes. As compared with the traditional 4-PAM scheme, the proposed scheme gives a good error performance for the HP bit stream with 0.2 dB gain increase at BER of 10-5, and exhibited a 4 dB gain when the channel condition is bad. Key words: Superposition coding, real time transmission, UEP, CSI, AWGN.

Unequally Error Protected Wireless Data Transmission Using Channel State Information and Adaptive Encoders

Problem statement: Higher data transmission rate with Quality of Serv ices (QoS) guarantee is an important objective for wireless br oadband communication systems. Unlike other communication system, real-time transmission requir es high data rate and good error performance to ensure good quality of service. This study descr ibes the design problem of real-time wireless data transmission which provides higher achievable data rate with Unequal Error Protection (UEP). Approach: Real-time data stream was divided equally into two streams, High Priority (HP) and Low Priority (LP) streams depending on their requirements. We considered these two bit streams as being encoded separately by two adaptive encoders. Feedback of Channel State Information (CSI) was used in adaptive physical lay er channel for efficient use of the current available bandwidth by controlling the encoders. Hi gh code rate were used in both encoders when the channel is good while low code rate is otherwis e. The two coded data streams were superimposed together with two different adjustable levels of power to achieve the UEP at the receiver end. Results: In this proposed scheme, same design metrics, name ly, time, bandwidth and power were used to increase the transmission effici ency. Conclusion/Recommendations: Results showed that our scheme provided higher error perfor mance for HP stream compared with other schemes that transmit using one power level data st ream. The finding can be modified for studying the effects of fading on this system in fu ture research.