Electron Transfer Rate Constant Research Articles

Investigation of the Electrocatalytic Reduction of Peroxydisulfate Using Scanning Electrochemical Microscopy.

The elementary steps of the electrocatalytic reduction of S2O82- using the Ru(NH3)63+/2+ redox couple were investigated using scanning electrochemical microscopy (SECM) and steady-state voltammetry (SSV). SECM investigations were carried out in a 0.1 M KCl solution using a 3.5 μm radius carbon ultramicroelectrode (UME) as the SECM tip and a 25 μm radius platinum UME as the substrate electrode. Approach curves were recorded in the positive feedback mode of SECM by reducing Ru(NH3)63+ at the tip electrode and oxidizing Ru(NH3)62+ at the substrate electrode, as a function of the tip-substrate separation and S2O82- concentration. The one-electron reaction between electrogenerated Ru(NH3)62+ and S2O82- yields the unstable S2O83•-, which rapidly dissociates to produce highly oxidizing SO4•-. Because SO4•- is such a strongly oxidizing species, it can be further reduced at both the tip and the substrate, or it can react with Ru(NH3)62+ to regenerate Ru(NH3)63+. SECM approach curves display a complex dependence on the tip-substrate distance, d, due to redox mediation reactions at both the tip and the substrate. Finite element method (FEM) simulations of both SECM approach curves and SSV confirm a previously proposed mechanism for the mediated reduction of S2O82- using the Ru(NH3)63+/2+ redox couple. Our results provide a lower limit for dissociation rate constant of S2O83•- (∼1 × 106 s-1), as well as the rate constants for electron transfer between SO4•- and Ru(NH3)62+ (∼1 × 109 M-1 s-1) and between S2O82- and Ru(NH3)62+ (∼7 × 105 M-1 s-1).

A comparative analysis of square-wave voltammetry and multi-frequency electrochemical Faradaic spectroscopy for kinetic characterisation

AbstractA rigorous comparison between square-wave voltammetry (SWV) and the recently proposed multi-frequency electrochemical Faradaic spectroscopy (MEFS) is presented for both a quasireversible electrode reaction of a dissolved redox couple at a planar macroscopic electrode and a catalytic regenerative electrode mechanism (EC′ reaction scheme) by means of numerical simulations. MEFS offers fast kinetic characterisation with a minimal set of experiments, as the system is interrogated with a range of SW frequencies in a single experiment. By changing the mid-potential Em, a critical parameter of MEFS, a broad range of standard rate constants for the heterogeneous interfacial electron transfer is accessible, ranging between 0.006 and 0.12 cm s−1. In the case of the EC′ mechanism, features of the current components in both SWV and MEFS reflect the involvement of the follow-up regenerative chemical reaction (i.e. C′ catalytic step). However, for the kinetic characterisation of the EC′ mechanism, the comparative analysis suggests that SWV should be the main operating technique.

Voltammetric Sensing of Chloride Based on a Redox-Active Complex: A Terpyridine-Co(II)-Dipyrromethene Functionalized Anion Receptor Deposited on a Gold Electrode.

A redox-active complex containing Co(II) connected to a terpyridine (TPY) and dipyrromethene functionalized anion receptor (DPM-AR) was created on a gold electrode surface. This host-guest supramolecular system based on a redox-active layer was used for voltammetric detection of chloride anions in aqueous solutions. The sensing mechanism was based on the changes in the redox activity of the complex observed upon binding of the anion to the receptor. The electron transfer coefficient (α) and electron transfer rate constant (k0) for the modified gold electrodes were calculated based on Cyclic Voltammetry (CV) experiments results. On the other hand, the sensing abilities were examined using Square Wave Voltammetry (SWV). More importantly, the anion receptor was selective to chloride, resulting in the highest change in Co(II) current intensity and allowing to distinguish chloride, sulfate and bromide. The proposed system displayed the highest sensitivity to Cl- with a limit of detection of 0.50 fM. The order of selectivity was: Cl- > SO42- > Br-, which was confirmed by the binding constants (K) and reaction coupling efficiencies (RCE).

Visible Light as a Promising Signal Amplification Tool for the Efficient Electrochemical Detection of Azithromycin Antibiotic by Using Photoactive Spinel Nickel Ferrite Nanoflakes

An efficient photoactive spinel NiFe2O4 nanoflakes (NFO NFs) was successfully prepared and integrated into an electrochemical sensor for the sensitive determination of Azithromycin (AZM) under visible light illumination. With the introduction of 532 nm laser illumination, NFO NFs could be easily excited and induce the charge-separation state with electrons in the conduction band and holes in the valence band. Upon illumination, the low band gap value in combination with edge-to-flat-surface/edge-to-edge conjunctions of NFO NFs could form the electron transfer pathway for transferring photogenerated electron-hole pairs to the AZM analyte-NFO electrode interface. Hence, the fabricated visible light-assisted NFO-based electrochemical sensor shows remarkable enhanced analytical performance, with calculated values of electron transfer rate constant, adsorption capacity, diffusion coefficient, and catalytic rate constant under visible light illumination of 1.29, 1.27, 2.08, and 3.40 times higher than in the dark condition, respectively. As a result, the NFO-based electrochemical sensing platform in the presence of visible light illumination possessed a high electrochemical sensitivity of 0.070 μA μM−1 in a wide linear dynamic range of 2.5–150 μM and a detection limit of 1.67 μM and also exhibited excellent anti-interference ability, repeatability, storage stability, reproducibility, and practical feasibility for AZM detection in pharmaceutical tablets.

Microbiologically influenced corrosion can cause a dental implant rejection

In the present study, we apply electrochemical and molecular biology approaches to establish whether microbiologically influenced corrosion (MIC) may be the reason for dental implant rejection. Titanium-based implants have been incubated in vitro in Ringer/glucose solution in the presence and absence of a salivary microbiota and the change in their corrosion potential and current density was monitored over time by potentiodynamic polarization. The charge transfers processes occurring on the Ti-based implant surface during the initial bacterial adhesion and after biofilm formation were analyzed by electrochemical impedance spectroscopy. The components of the equivalent electrical circuit as well as the heterogeneous electron transfer rate constants were estimated. In parallel, bacterial species from the salivary microbiota have been identified by sequencing of the 16S ribosomal amplicon method, and their contribution to the corrosion processes of dental implants was verified and compared to that of native saliva in vitro. The scanning electron microscopy observation and energy dispersive spectroscopy analysis of the implant surface after long-term exposure to a bacterial-containing environment revealed more detailed features of the occurring corrosion processes.

Ultrafast Electron Transfer from CuInS2 Quantum Dots to a Molecular Catalyst for Hydrogen Production: Challenging Diffusion Limitations.

Systems integrating quantum dots with molecular catalysts are attracting ever more attention, primarily owing to their tunability and notable photocatalytic activity in the context of the hydrogen evolution reaction (HER) and CO2 reduction reaction (CO2RR). CuInS2 (CIS) quantum dots (QDs) are effective photoreductants, having relatively high-energy conduction bands, but their electronic structure and defect states often lead to poor performance, prompting many researchers to employ them with a core-shell structure. Molecular cobalt HER catalysts, on the other hand, often suffer from poor stability. Here, we have combined CIS QDs, surface-passivated with l-cysteine and iodide from a water-based synthesis, with two tetraazamacrocyclic cobalt complexes to realize systems which demonstrate high turnover numbers for the HER (up to >8000 per catalyst), using ascorbate as the sacrificial electron donor at pH = 4.5. Photoluminescence intensity and lifetime quenching data indicated a large degree of binding of the catalysts to the QDs, even with only ca. 1 μM each of QDs and catalysts, linked to an entirely static quenching mechanism. The data was fitted with a Poissonian distribution of catalyst molecules over the QDs, from which the concentration of QDs could be evaluated. No important difference in either quenching or photocatalysis was observed between catalysts with and without the carboxylate as a potential anchoring group. Femtosecond transient absorption spectroscopy confirmed ultrafast interfacial electron transfer from the QDs and the formation of the singly reduced catalyst (CoII state) for both complexes, with an average electron transfer rate constant of <kET> ≈ (10 ps)-1. These favorable results confirm that the core tetraazamacrocyclic cobalt complex is remarkably stable under photocatalytic conditions and that CIS QDs without inorganic shell structures for passivation can act as effective photosensitizers, while their smaller size makes them suitable for application in the sensitization of, inter alia, mesoporous electrodes.

Understanding first electron transfer kinetic process of electrochemical nitrate reduction to ammonia on Fe2O3 nanorods array

Electroreduction reaction of nitrate (NO3RR) to ammonia (NH3) using reproducible energy is an effective alternative strategy to energy-intensive Haber-Bosch process and potentially energy storage. However, the reaction needs coupling of multiple electrons and protons, considering it a grand challenge to NH3 yield and selectivity affected by slow electron transfer kinetic processes. Herein, we investigate the electrode kinetics process by Tafel plots on Fe2O3 nanorods array electrocatalysts, confirming that the process of the first electron transfer is involved in the rate-determining step (RDS) for NO3RR. The reaction rate constant (k) of the first electron transfer (NO3– + e-→*NO3) indicates that Fe2O3 electrocatalyst treated at 450 ℃ has a faster electron transfer kinetic and thus exhibits a higher NH3 yield. Furthermore, operando EIS and in situ Raman spectroscopic characterizations demonstrate that electron gaining and losing process of Fe promotes the transfer of the first electron to NO3–, thus substantially accelerating the kinetic process of the RDS. These results provide key insight into the metal oxide-based electrocatalysts kinetic processes on the performance of NO3RR.

Electrochemical Aptasensing Platform for the Detection of Retinol Binding Protein-4.

Here, we present the results of our the electrochemical aptasensing strategy for retinol binding protein-4 (RBP-4) detection based on a thiolated aptamer against RBP-4 and 6-mercaptohexanol (MCH) directly immobilized on a gold electrode surface. The most important parameters affecting the magnitude of the analytical signal generated were optimized: (i) the presence of magnesium ions in the immobilization and measurement buffer, (ii) the concentration of aptamer in the immobilization solution and (iii) its folding procedure. In this work, a systematic assessment of the electrochemical parameters related to the optimization of the sensing layer of the aptasensor was carried out (electron transfer coefficients (α), electron transfer rate constants (k0) and surface coverage of the thiolated aptamer probe (ΓApt)). Then, under the optimized conditions, the analytical response towards RBP-4 protein, in the presence of an Fe(CN)63-/4- redox couple in the supporting solution was assessed. The proposed electrochemical strategy allowed for RBP-4 detection in the concentration range between 100 and 1000 ng/mL with a limit of detection equal to 44 ng/mL based on electrochemical impedance spectroscopy (EIS). The specificity studies against other diabetes biomarkers, including vaspin and adiponectin, proved the selectivity of the proposed platform. These preliminary results will be used in the next step to miniaturize and test the sensor in real samples.

Reviving the absorbent chemistry of electrochemically mediated amine regeneration for improved point source carbon capture

Electrochemically mediated amine regeneration (EMAR) is emerging as a promising electrochemical approach for carbon capture from point sources. In this study, for the first time, the absorbent chemistry of the EMAR process was revived by considering criteria beyond metal-amine complexation. The systematic investigation focused on using second amines, which were previously overlooked in EMAR due to limited metal-amine interaction, despite their proven effectiveness in conventional carbon capture processes. The integration of second amines— monoethanolamine (MEA), aminomethyl propanol (AMP), and methyldiethanolamine (MDEA)—with the benchmark ethylenediamine (EDA) was thoroughly studied, evaluating their impact on absorption and desorption kinetics and capacities, and electrochemical performance. Among the blends, EDA + MDEA emerged as the top performer, particularly excelling in electrochemical aspects. The charge transfer resistance (RCT) of the deposition reaction, as the rate-limiting step, for the EDA + MDEA blend was reduced by 40 % compared to pure EDA, and the heterogeneous electron transfer rate constant (k0) improved threefold. In the bench-scale assessments, the EDA + MDEA blend showed a notable decrease in desorption energetics to 37 kJ/molCO2, marking a 34 % reduction compared to the 56 kJ/molCO2 required for pure EDA. This marks the lowest reported energetics for an EMAR process targeting point source carbon capture. This research paves the way for future systematic investigations of a wider range of amine blends for EMAR and eventually the process implementation at larger scales.

1-D Carbon Nano-Coils Derived from Almond Skin: Exhibiting Density of State, Diffusivity, Electron Transfer Rate, and Dopamine Redox Modulation Properties Akin to Graphene Oxide.

The quest to develop graphene-like biomass-carbon for advanced biomolecule redox modulation and sensing remains a challenge. The primary obstacle is the limited ability of biomass to undergo extensive graphitization during pyrolysis resulting in the formation of amorphous carbon materials with a small carbon-double-bond-carbon domain size (Lsp2 ), density of state (LDOS), ion diffusivity (D), and electron transfer rate constant (Ks). Herein, using almond skin (AS) the morphology of biomass is demonstrated as the key to overcoming these limitations. AS consists of 1D syringyl/guaiacyl lignin nano-coils which under H2 /H2 annealing transform into pyrolytic 1D carbon nano-coils (r-gC). Spectroscopy and microscopy analyses reveal that the sheet layering structure, crystallinity, LDOS, and Lsp2 of r-gC mimic those of graphene oxide (GO). Moreover, its unique 1D morphology and profound microstructure facilitate faster charge transfer and ion diffusion than GO's planar structure, leading to better redox modulation and sensing of the neurotransmitter dopamine (DA) in physiological fluids. r-gC's DA detection limit of 3.62nM is below the lower threshold found in humans and on par with the state-of-the-art. r-gC is also DA-selective over 14 biochemicals. This study reveals that biomasses with well-defined and compact lignin structures are best suited for developing highly electroactive graphene-like biomass carbon.

Comparison of Different Electrochemical Methodologies for Electrode Reactions: A Case Study of Paracetamol

Understanding electrochemical reactions at the surface of electrodes requires the accurate calculation of key parameters—the transfer coefficient (α), diffusion coefficient (D0), and heterogeneous electron transfer rate constant (k0). The choice of method to calculate these parameters requires careful consideration based on the nature of the electrochemical reaction. In this study, we conducted the cyclic voltammetry of paracetamol to calculate the values of these parameters using different methods and present a comparative analysis. Our results demonstrate that the Ep − Ep/2 equation for α and the modified Randles–Ševčík equation for D0 is particularly effective for the calculations of these two parameters. The Kochi and Gileadi methods are reliable alternatives for the calculation of k0. Nicholson and Shain’s method using the equation k0 = Ψ(πnD0Fν/RT)1/2 gives the overestimated values of k0. However, the value of k0 calculated using the plot of ν−1/2 versus Ψ (from the Nicholson and Shain equation, where ν is scan rate) agrees well with the values calculated from the Kochi and Gilaedi methods. This study not only identifies optimal methodologies for quasi-reversible reactions but also contributes to a deeper understanding of electrochemical reactions involving complex electron transfer and coupled chemical reactions, which can be broadly applicable in various electrochemical studies.

Electrochemical measurement of the electronic structure of graphene via quantum mechanical rate spectroscopy

Quantum-rate theory defines a quantum mechanical rate ν that complies with the Planck–Einstein relationship E=hν, where ν=e2/hCq is a frequency associated with the quantum capacitance Cq, and E=e2/Cq is the energy associated with ν. Previously, this definition of ν was successfully employed to define a quantum mechanical meaning for the electron-transfer (ET) rate constant of redox reactions, wherein faradaic electric currents involved with ET reactions were demonstrated to be governed by relativistic quantum electrodynamics at room temperature (Bueno, 2023c).This study demonstrated that the definition of ν entails the relativistic quantum electrodynamics phenomena intrinsically related to the perturbation of the density-of-states dn/dE=Cq/e2 by an external harmonic oscillatory potential energy variation. On this basis, the electronic structure of graphene embedded in an electrolyte environment was computed. The electronic structure measured using quantum-rate spectroscopy (QRS) is in good agreement with that measured through angle-resolved photo-emission spectroscopy (ARPES) or calculated via computational density-functional theory (DFT) methods.Electrochemical QRS has evident experimental advantages over ARPES. For instance, QRS enables obtaining the electronic structure of graphene at room temperature and in an electrolyte environment, whereas ARPES requires low temperature and ultrahigh-vacuum conditions. Furthermore, QRS can operate in-situ using a hand-held, inexpensive piece of equipment, whereas ARPES necessarily requires expensive and cumbersome apparatus.

Electrochemical Behavior of Quinones Classically Used for Bioenergetical Applications: Considerations and Insights about the Anodic Side

AbstractQuinones are electrochemical probes which are used for a large range of applications including bioenergetics. One electrochemical feature of quinones is their possible slow electron transfer kinetics. In this article we compared several quinones towards electron transfer kinetics and the ability of anodic pretreatment to increase electron transfer rate constant. Rotating disk electrode and chronoamperometry measurements were used to revisit their electrochemical behavior. Additionally, the number of electrons exchanged as a function of the characteristic time was used as a proxy to investigate kinetic limitations. A model was suggested to rationalize our results. Beyond a classification of quinones regarding the kinetic and thermodynamic ability of the hydroquinone form to be re‐oxidized, some intrinsic physicochemical properties were identified from our model (such as a time dependency of the exchanged number of electrons) to characterize such important redox mediators.

Photolysis mechanism of Di(tert‐butylphenyl)iodonium salt using 2‐isopropylthioxanthone as a sensitizer

AbstractDiaryliodonium salts (Ar2I+X−) are used as a photosensitive initiator that generates acid or radical species by ultraviolet light irradiation. Recently, sensitization of Ar2I+X− has gained importance owing to the escalating demand for high‐sensitive initiators with longer wavelength absorption such as 365 and 436 nm. However, the mechanism of photolysis of Ar2I+X− has not been strictly elucidated. This paper shows discussions of the details of its mechanism. Herein, we analyzed the photosensitization of Ar2I+X− with 2–isopropylthioxanthone (ITX) based on transient absorption techniques. As a result, it was revealed that electron transfer occurred from a triplet excited state of ITX to Ar2I+X− with an electron transfer rate constant of 4.2 × 109 s−1. Furthermore, high performance liquid chromatography measurements found the quantum yield of the photolysis was determined to be 0.48.

An on-site and portable electrochemical sensing platform based on spinel zinc ferrite nanoparticles for the quality control of paracetamol in pharmaceutical samples.

In this study, crystalline spinel zinc ferrite nanoparticles (ZnFe2O4 NPs) were successfully prepared and proposed as a high-performance electrode material for the construction of an electrochemical sensing platform for the detection of paracetamol (PCM). By modifying a screen-printed carbon electrode (SPE) with ZnFe2O4 NPs, the electrochemical characteristics of the ZnFe2O4/SPE and the electrochemical oxidation of PCM were investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), chronoamperometry (CA), and differential pulse voltammetry (DPV) methods. The calculated electrochemical kinetic parameters from these techniques including electrochemically active surface area (ECSA), peak-to-peak separation (ΔEp), charge transfer resistance (Rct), standard heterogeneous electron-transfer rate constants (k0), electron transfer coefficient (α), catalytic rate constant (kcat), adsorption capacity (Γ), and diffusion coefficient (D) proved that the as-synthesized ZnFe2O4 NPs have rapid electron/mass transfer characteristics, intrinsic electrocatalytic activity, and facilitate the adsorption-diffusion of PCM molecules towards the modified electrode surface. As expected, the ZnFe2O4/SPE offered excellent analytical performance towards sensing of PCM with a detection limit of 0.29 μM, a wide linear range of 0.5-400 μM, and high electrochemical sensitivity of 1.1 μA μM-1 cm-2. Moreover, the proposed ZnFe2O4-based electrochemical nanosensor also exhibited good repeatability, high anti-interference ability, and practical feasibility toward PCM sensing in a pharmaceutical tablet. Based on these observations, the designed electrochemical platform not only provides a high-performance nanosensor for the rapid and highly efficient detection of PCM but also opens a new avenue for routine quality control analysis of pharmaceutical formulations.

On the fundamentals of quantum rate theory and the long-range electron transport in respiratory chains.

It has been shown that both the electron-transfer rate constant of an electrochemical reaction and the conductance quantum are correlated with the concept of quantum capacitance. This simple association between the two separate concepts has an entirely quantum rate basis that encompasses the electron-transfer rate theory as originally proposed by Rudolph A. Marcus whether statistical mechanics is appropriately taken into account. I have prepared a concise review of the quantum mechanical rate theory principles focused on its quantum electrodynamics character to demonstrate that it can reconcile the conflicting views established on attempting to use the super-exchange (supported on electron transfer) or 'metallic-like' (supported on conductance quantum) mechanisms separately to explain the highly efficient long-range electron transport observed in the respiratory processes of living cells. The unresolved issues related to long-range electron transport are clarified in light of the quantum rate theory with a discussion focused on Geobacter sulfurreducens films as a reference standard of the respiration chain. Theoretical analyses supported by experimental data suggest that the efficiency of respiration within a long-range electron transport path is intrinsically a quantum mechanical event that follows relativistic quantum electrodynamics principles as addressed by quantum rate theory.

The effect of gold nanostructure morphology on label-free electrochemical immunosensor design

In this research, various electrodeposition techniques were used to form gold nanostructures (AuNSs) on the surface of graphite rod electrode (GE). Three distinct AuNS morphologies on GE have been achieved based on the composition of electrodeposition solution. The use of H2SO4 as a supporting electrolyte resulted in the formation of smaller but more numerous AuNSI with a modified electrode’s electroactive surface area (EASA) of 0.213 cm2. Exchanging the supporting electrolyte to KNO3 and increasing HAuCl4 concentration facilitated the formation of bigger AuNSII particles with electrode EASA of 0.116 cm2. Finally, a partial coverage of GE by branched gold nanostructures (AuNSIII) was achieved with an estimated EASA of 0.110 cm2, when the HAuCl4 and KNO3 concentrations were increased. Estimated values of heterogeneous electron transfer rate constant did not depend on AuNS morphology. Electrode modified with AuNSI exhibited the highest bovine serum albumin (BSA) immobilization efficiency and the highest relative response for the detection of specific polyclonal antibodies against BSA (p-anti-BSA) compared to other modified electrodes. The limit of p-anti-BSA detection in PBS buffer was calculated as 0.63 nM, while in blood serum it was 0.71 nM. Linear ranges were from 1 to 7 nM and from 1 to 5 nM, respectively.

Nanoscale Photoelectrochemical Mapping of Two-Dimensional Electrodes

Electron transfer plays a significant role in many chemical processes, especially in the catalytic reactions involved in photoelectrochemical energy conversion and storage. Revealing the electron transfer behavior at the interface of electrode-electrolyte is thus of great importance. Here we fabricate atomically thin semiconductor MX2 (M = Mo, W; X = S, Se) by chemical vapor deposition method and directly map the photoelectrochemical behavior using Atomic Force Microscopy-combined with light-induced Scanning Electrochemical Microscopy (AFM-SECM). AFM-SECM feedback mapping shows a layer-dependent photoelectrocatalytic ability of MX2 to oxidize the redox species Ru2+ back to Ru3+. Moreover, AFM-SECM generation and collection mode shows the potential-dependent edge and basal plane activity for the hydrogen evolution reaction of WSe2. Compared with monolayer and bilayer, few-layer WSe2 shows better stability in an electrochemical environment, faster electron transfer, and higher hydrogen production. Furthermore, finite element method based numerical simulations using MATLAB® and COMSOL Multiphysics® is performed to calculate the electron transfer rate constants k0 and simulate the steady-state concentration gradient. Finally, the photoelectrochemistry at MX2 electrode-electrolyte interfaces are spatially resolved and understanding this behavior will be useful for the future photoelectrochemical devices.

(Invited) The Effect of Surfactants on Vanadium Electrochemistry in Porous Carbon Electrodes

We present a study of vanadium electrochemistry in porous electrodes with and without sodium dodecyl sulfate (SDS) additives present. Carbon paper and felt electrodes are compared. Carbon felt electrodes are the de facto standard in flow batteries. There are significant differences in the electronic conductivity of these media. The carbon paper has a much higher conductivity than the felt, which has an electronic conductivity similar to the ionic conductivity of the electrolytes used. The latter fact motivates an extension of available theory for polarization curve fitting to explicitly include both electronic and ionic contributions in the porous electrode. We demonstrate agreement between our model and an existing model evaluated at the limit where electrode conductivity is significantly greater than electrolyte conductivity. Our model uses the product of the electrode surface area per volume ratio and the heterogeneous electron transfer rate constant, and the Damköhler number as fitting parameters for carbon paper and felt electrodes. We discuss the effect of SDS additives on kinetics in the context of the cation hydration shell for the vanadium ions. To this point, we apply Marcus-Hush-Chidsey formalism to our porous electrode model to quantify reorganization energies obtained through polarization curve fitting. This work was supported as part of the Breakthrough Electrolytes for Energy Storage (BEES2), an Energy Frontier Research Center funded by the United States. Department of Energy, Office of Science, Basic Energy Sciences under Award # DE-SC0019409.

Effect of Aspect Ratio of a Gold-Nanorod-Modified Screen-Printed Carbon Electrode for Carbaryl Detection in Three Different Samples of Vegetables.

In this study, three different sizes of gold nanorods (AuNRs) were synthesized using the seed-growth method by adding various volumes of AgNO3 as 400, 600, and 800 μL into the growth solution of gold nanoparticles. Three different sizes of AuNRs were then characterized using UV-vis spectroscopy, high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED) patterns, and atomic force microscopy (AFM) to investigate the surface morphology, topography, and aspect ratios of each synthesized AuNR. The aspect ratios from the histogram of size distributions of three AuNRs as 2.21, 2.53, and 2.85 can be calculated corresponding to the addition of AgNO3 volumes of 400, 600, and 800 μL. Moreover, each AuNR in three different aspect ratios was drop-cast onto the surface of a commercial screen-printed carbon electrode (SPCE) to obtain three different SPCE-modified AuNRs (SPCE-A400, SPCE-A600, and SPCE-A800, respectively). All SPCE-modified AuNRs were then evaluated for their electrochemical behavior using cyclic voltammetry and electrochemical impedance spectroscopy (EIS) techniques and the highest electrochemical performance was shown as the order of magnitude of SPCE-A400 > SPCE-A600/SPCE-A800. The reason for the highest electrocatalytic activity of SPCE-A400 might be due to the smallest particle size and uniform distribution of AuNRs ∼ 2.2, which enhanced the charge transfer, thus providing the highest electroactive surface area (0.6685 cm2) compared to other electrodes. These results also confirm that the sensing mechanism for all SPCE-modified AuNRs is controlled by diffusion phenomena. In addition, the optimum pH was obtained as 4 for carbaryl detection for all SPCE-modified AuNRs with the highest current shown by SPCE-A400. Furthermore, SPCE-A400 has the highest fundamental parameters (surface coverage, catalytic rate constant, electron transfer rate constant, and adsorption capacity) for carbaryl detection, which were investigated using cyclic voltammetry and chronoamperometric techniques. The electroanalytical performances of all SPCE-modified AuNRs for carbaryl detection were also investigated with SPCE-A400 displaying the best performance among other electrodes in terms of its linearity (0.2-100 μM), limit of detection (LOD) ∼ 0.07 μM, and limit of quantification (LOQ) ∼ 0.2 μM. All SPCE-modified AuNRs were also subsequently evaluated for their stability, reproducibility, and selectivity in the presence of interfering species such as NaNO2, NH4NO3, Zn(CH3CO2)2, FeSO4, diazinon, and glucose and show reliable results as depicted from %RSD values less than 3%. At last, all SPCE-modified AuNRs have been employed for carbaryl detection using a standard addition technique in three different samples of vegetables (cabbage, cucumber, and Chinese cabbage) with its results (%recovery ≈ 100%) within the acceptable analytical range. In conclusion, this work demonstrates the great potential of a disposable device based on an AuNR-modified SPCE for rapid detection and high sensitivity in monitoring the concentration of carbaryl as a residual pesticide in vegetable samples.