Control Of Quality Factor Research Articles

Control of quality factor of atomic force microscopy cantilever by cavity optomechanical effect

The effective quality factor of the cantilever plays a fundamental role in dynamic mode atomic force microscopy. Here we present a technique to modify the quality factor of an atomic force microscopy cantilever within a Fabry–Perot optical interferometer. The experimental setup uses two separate laser sources to detect and excite the oscillation of the cantilever. While the intensity modulation of the excitation laser drives the oscillation of the cantilever, the average intensity can be used to modify the quality factor via optomechanical force without changing the fiber-cantilever cavity length. The technique enables users to optimize the quality factor for different types of measurements without influencing the deflection measurement sensitivity. An unexpected frequency shift was observed and modelled as temperature dependence of the cantilever’s Young’s modulus, which was validated using finite element simulation. The model was used to compensate for the thermal frequency shift. The simulation provided relations between optical power, temperature, and frequency shift.

Antenna-Based Approach to Fine Control of Supercavity Mode Quality Factor in Metasurfaces.

The utilization of photonic bound states in the continuum (BIC) is a very attractive approach for many applications requiring efficient resonators. High-Q modes related to symmetry-protected BIC are formed due to perturbation defined by an asymmetry parameter, and the smaller this parameter is, the bigger the Q factor can be achieved. Inevitable fabrication imperfectness limits precise control of the Q factor through the asymmetry parameter. Here we propose an antenna-based design of metasurfaces for accurate tailoring of the Q factor where stronger perturbation leads to the same effect in the conventional design. This approach allows the fabrication of samples with equipment having lower tolerance keeping the Q factor at the same level. Furthermore, our findings reveal two regimes of the Q factor scaling law with saturated and unsaturated resonances dependent on the ratio of antenna particles to all particles. The boundary is defined by the efficient scattering cross section of the metasurface constituent particles.

Hybridization of surface lattice modes: towards plasmonic metasurfaces with high flexible tunability

Abstract When assembled in periodic arrangements, metallic nanostructures (NSs) support plasmonic surface lattice (SL) resonances resulting from long-range interactions these surface lattice resonances differ radically from localized surface plasmon (LSP). Similarly to the hybridization of LSP resonances, observed in short-range interactions, we demonstrate the possibility to generate a hybridization of surface lattice (SL) plasmon resonances, by the excitation of grazing order diffraction within the metasurface. This hybridization leads to the emergence of bonding and anti-bonding modes. If hybridization of LSP modes has been widely described in recent literature, there is still no experimental proof-of-concept reporting such hybridization with SL plasmon resonances. We fill this gap in the present paper by considering surfaces made of binary arrays with unit cells made of two gold disks of distinct diameters. We demonstrate the possibility to maximize or cancel the interaction between the hybridized SL resonances by simply controlling the distance between particles. All our experimental results are supported by FDTD calculations. The hybridization of SL modes results in much richer hybridization scenario in terms of wavelength and quality factor control, compared to a hybridization of LSP in a short-range configuration. It offers unprecedented opportunities to generate innovative optical devices, with high flexible tunability.

Control of vibration nonlinearity and quality factor for a carbon nanotube mass sensor

Control of vibration nonlinearity and quality factor for a carbon nanotube mass sensor

Reconfigurable Filtering Power Divider With Arbitrary Operating Channels Based on External Quality Factor Control

In this paper, we propose a scheme to design the reconfigurable filtering power divider with arbitrary operating channels based on external quality factor ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$Q_{\mathbf {e}}$ </tex-math></inline-formula> ) control. By using an input feeding line, <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${n}$ </tex-math></inline-formula> resonators, and <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$m$ </tex-math></inline-formula> output feeding lines, the <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$n^{\mathbf {th}}$ </tex-math></inline-formula> -order <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$m$ </tex-math></inline-formula> -way filtering power divider topology can be obtained with a simple configuration. A coupled-line output feeding structure loading with multiple PIN diodes is proposed to adjust the output <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$Q_{\mathbf {e}}$ </tex-math></inline-formula> values. Design theories for obtaining the desired <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$Q_{\mathbf {e}}$ </tex-math></inline-formula> values are provided. Then, the filtering power divider can be fully reconfigured in the states with one to <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$m$ </tex-math></inline-formula> operating channels. Good input matching can be achieved without using an additional reconfigurable impedance matching network in all these states, resulting in a size and loss reduction. For verification, a 2nd-order 4-way reconfigurable filtering power divider is designed, fabricated, and measured. As compared to the reported reconfigurable power dividers, the proposed design shows the merits of fully reconfigurable operating channels, favorable filtering responses, low insertion losses, high isolation, and a simple structure.

Quality factor control of mechanical resonators using variable phononic bandgap on periodic microstructures

The quality factor (Q-factor) is an important parameter for mechanical resonant sensors, and the optimal values depend on its application. Therefore, Q-factor control is essential for microelectromechanical systems (MEMS). Conventional methods have some restrictions, such as additional and complicated equipment or nanoscale dimensions; thus, structural methods are one of the reasonable solutions for simplifying the system. In this study, we demonstrate Q-factor control using a variable phononic bandgap by changing the length of the periodic microstructure. For this, silicon microstructure is used because it has both periodicity and a spring structure. The bandgap change is experimentally confirmed by measuring the Q-factors of mechanical resonators with different resonant frequencies. The bandgap range varies depending on the extended structure length, followed by a change in the Q-factor value. In addition, the effects of the periodic structure on the Q-factor enhancement and the influence of stress on the structural length were evaluated. Although microstructures can improve the Q-factors irrespective of periodicity; the result of the periodic microstructure is found to be efficient. The proposed method is feasible as the novel Q-factor control technique has good compatibility with conventional MEMS.

Molecularization of meta-atoms for electromagnetically induced transparency resonance and quality-factor switching

Electromagnetically induced transparency (EIT) analogs in terahertz regimes have been actively tuned by hybridizing semiconductors into metasurfaces for effective terahertz manipulation. Although several multiple means have been adopted to modulate EIT, the active control of the EIT quality factor is less reported. Multifunctional EIT modulation should also be considered. In this study, we fabricated a terahertz metadevice by embedding Si bridges into a metasurface with optically controllable molecularization of terahertz meta-atoms and experimentally demonstrated dual-functional terahertz EIT modulation, including resonance amplitude modulation and quality-factor modulation. For a low-power pumping of 16 mW, ultrafast EIT resonance amplitude modulation can be achieved with a low-level molecularization, with a normalized amplitude modulation of up to 85%. Then, with a high-power pumping of 360 mW, we performed ultrafast EIT quality-factor switching, where the high Si-bridge conductivity altered the spatial interconnected structure and exhibited high-level molecularization. Both functions have a nanosecond-scale modulation speed. In addition, we numerically and theoretically explained the terahertz modulation and molecularization behaviors, which was consistent with the experimental results. Our proposed all-optical active terahertz metadevice with controllable molecularization provides a novel solution for multifunctional and ultrafast switchable terahertz modulators.

Voltage-Mode Biquad Filter Using Four OTAs and Its Application in Quadrature Oscillator with Noninteractive Control of the Oscillation Condition and Frequency

This paper presents an independently tunable, four-input, three-output, voltage-mode (VM) biquad filter consisting of four operational transconductance amplifiers (OTAs) and two grounded capacitors. The proposed circuit can simultaneously realize three basic biquad filtering functions for single input and three outputs. All five standard biquad filtering functions can be implemented with four inputs and single output by appropriate application of input voltage signals. The developed biquad filter with high input impedances enables noninteractive control of natural angular frequency and quality factor. By slightly modifying the proposed biquad filter, the VM quadrature sinusoidal oscillator with noninteractive control for the oscillation condition and the oscillation frequency has been achieved. Simulation and experimental results are used to validate theoretical predictions.

Synthesis of biquad filters using two VD-DIBAs with independent control of quality factor and natural frequency

This contribution presents the procedure to synthesis the voltage-mode active biquad filters using the active elements, voltage differencing differential input buffered amplifier (VD-DIBA). Two filtering categories, single input four output (SIFO) configuration and three input three output (TITO) configuration are proposed. Both proposed filters consist of two VD-DIBAs, two grounded capacitors and two resistors. All input voltage nodes for both biquad filters exhibit high impedance. The proposed SIFO biquad filter simultaneously provide four filtering responses, low pass (LP), band pass (BP), high pass (HP) and band reject (BR) functions, while the proposed TITO filter provides five filtering responses (including all pass (AP) function). The natural frequency (ω0) is linearly and electronically tuned without affecting the quality factor (Q). Also, the Q adjusting can be done without affecting the ω0. By modifying the proposed TITO biquad filter, the current controlled sinusoidal oscillator is achieved. The frequency of the generated sinewave is linearly tuned without affecting the condition of oscillation. The performances of the proposed circuits are simulated by Cadence software and the Spectre simulator of the Analog Design Environment using CMOS VD-DIBA in 0.18 μm TSMC CMOS technology and laboratory experiment using VD-DIBA constructed from commercially available ICs.

Enhanced harmonic generation in gases using an all-dielectric metasurface

Abstract Strong field confinement, long-lifetime resonances, and slow-light effects suggest that metasurfaces are a promising tool for nonlinear optical applications. These nanostructured devices have been utilized for relatively high efficiency solid-state high-harmonic generation platforms, four-wave mixing, and Raman scattering experiments, among others. Here, we report the first all-dielectric metasurface to enhance harmonic generation from a surrounding gas, achieving as much as a factor of 45 increase in the overall yield for Argon atoms. When compared to metal nanostructures, dielectrics are more robust against damage for high power applications such as those using atomic gases. We employ dimerized high-contrast gratings fabricated in silicon-on-insulator that support bound states in the continuum, a resonance feature accessible in broken-symmetry planar devices. Our 1D gratings maintain large mode volumes, overcoming one of the more severe limitations of earlier device designs and greatly contributing to enhanced third- and fifth-harmonic generation. The interaction lengths that can be achieved are also significantly greater than the 10’s of nm to which earlier solid-state designs were restricted. We perform finite-difference time-domain simulations to fully characterize the wavelength, linewidth, mode profile, and polarization dependence of the resonances. Our experiments confirm these predictions and are consistent with other nonlinear optical properties. The tunable wavelength dependence and quality factor control we demonstrate in these devices make them an attractive tool for the next generation of high-harmonic sources, which are anticipated to be pumped at longer wavelengths and with lower peak power, higher repetition rate lasers.

Different Features of Control Systems for Single-Phase Voltage Source Inverters

The aim of this paper is to determine which type of control loop is better for each particular type of standard voltage source inverter (VSI) load (static, dynamic, nonlinear rectifier resistive-capacitive RC load). A comparison of three different types of controllers for single-phase VSIs is presented. The first two are of the single input single output (SISO)/proportional-integral-derivative controller (PID) and coefficient diagram method (CDM) types, and the third is of the multi-input single output (MISO)/passivity-based control (PBC) type. The selections of the gains for SISO and MISO controllers are presented, including the problem in the choice of PBC controller gains caused by the imperfection of the pulse width modulation (PWM) modulator. For a standard nonlinear rectifier RC load, the new control quality factor (CQF) is defined to distinguish the properties of the controllers. The results show the superiority of the MISO-PBC controller for the RC load; however, for a linear dynamic load, the MISO-PBC performed worse than the SISO-PID or CDM. Therefore, the choice between either a simple and inexpensive SISO with one measurement trace or an expensive MISO with three measurement traces depends on the purpose of the VSI. The initial simulations and measurements of the experimental models are presented and discussed.

Hybrid cascode compensation with Q-factor control module for three-stage OTAs driving ultra-large load capacitors

PurposeThe purpose of this study is to discuss the effect of hybrid cascode compensation with quality factor (Q-factor) control module for the three-stage amplifiers driving ultra-large load capacitors. Compared to the present frequency compensation solutions, it extends the amplifier bandwidth by establishing an extra AC feedback pathway besides the primary pathway through the Miller capacitor, increasing the loop gain at the gain–bandwidth product (GBW) frequency by pushing to the higher frequencies the nondominant poles.Design/methodology/approachA Q-factor control block is used to improve the damping factor of the compensation loop with no power or area overhead, thereby reducing the frequency peaking and the undesired oscillation in the time response for small load capacitors. The Q-factor control module is realized by a tiny-size on-chip capacitor, and provides an extra feedback loop to feed the damping current back to the input stage. A left-half-plane (LHP) zero is also introduced to further improve the stability.FindingsA prototype of the proposed amplifier is simulated in 180-nm CMOS with a quiescent current of 24-µA from 1.80-V voltage supply. It achieves a 3.98-MHz gain–bandwidth product for 500-pF load capacitor, while the overall compensation capacitor is limited to 0.5-pF and the DC gain is extended beyond 100-dB.Originality/valueThe proposed amplifier is absolutely stable for the load capacitors ranging between 80-pF and 100-nF.

Control of quality factor in laterally coupled vertical cavities

In this work, the authors demonstrate the control of quality factor (Q-factor) is laterally coupled vertical cavities. A 3 μm-side-length square cavity directly connected to a 1.5 μm-width, 10 μm-length Fabry–Perot (FP) cavity has been fabricated and measured. Dynamic tuning of the Q-factor has been successfully observed by bringing the square cavity and FP cavity into resonance. The vertical-cavity-based Q-factor control scheme provides a new choice for the modulation of light and holds potentials for applications associated with optical information processing.

A microchip microcontroller-based transducer controller for non-contact scanning probe microscopy with phase-locked loop, amplitude, and Q control.

An inexpensive yet versatile transducer controller for non-contact scanning probe microscopy (SPM) based on a PIC32 microcontroller from Microchip Technology, Inc is described. In addition to feedback control using the amplitude or phase of the signal from the non-contact transducer, the controller includes a phase-locked loop for frequency-shift feedback, as well as fixed-amplitude, quality factor (Q) control, and self-excitation modes. Apart from the input amplifiers, output buffers, and the Q-control circuit, all other functions of the controller are instantiated in software on the microchip, enabling rapid changes in operating parameters if needed. The controller communicates with a host personal computer via a simple serial connection. The controller has been tested with a quartz tuning-fork transducer but can be used with any oscillating non-contact transducer.

A CFOA-Based Voltage-Mode Multifunction Biquadratic Filter and a Quadrature Oscillator Using the CFOA-Based Biquadratic Filter

This paper proposes a new high-input impedance current feedback operational amplifier (CFOA)- based voltage-mode multifunction biquadratic filter and a voltage-mode quadrature oscillator using the proposed high-input impedance CFOA-based biquadratic filter. The proposed high-input impedance CFOA-based voltage-mode multifunction biquadratic filter uses three CFOAs, three resistors, and two grounded capacitors with two inputs and three outputs. The filter can simultaneously realize non-inverting low-pass, non-inverting band-pass, and non-inverting band-reject filtering functions at the high-input impedance terminal while the inverting band-pass and non-inverting high-pass filtering functions can also be obtained by applying another high-input impedance terminal. The filter offers orthogonal control of resonance angular frequency and quality factor. The proposed high-input impedance CFOA-based voltage-mode multifunction biquadratic filter can be used to implement a voltage-mode quadrature oscillator with an independently controlled the frequency of oscillator and the condition of oscillation. The OrCAD PSpice simulation and experimental results of the commercially available integrated circuit, AD844AN, are used to confirm the characteristics of the proposed filter and oscillator.

Development of control quality factor for HVAC control loop performance assessment I—Methodology (ASHRAE RP-1587)

This article is the second paper from the ASHRAE research project RP-1587, focusing on the methodology of obtaining a control quality factor (CQF). This article presents a development of two CQFs for assessing the heating, ventilation, and air-conditioning (HVAC) control loop performance. Both CQFs are able to detect whether the control loop is able to maintain the setpoint and identify the loop’s ability to handle disturbances. In addition, the reversal behaviors are assessed as well. The first CQF (CQF-Harris) is proposed based on the normalized Harris index using the recursive least squares method. This recursive least squares method is selected because of its computational efficiency compared with the maximum likelihood estimation method. The second CQF (CQF-EWMA) is based on the exponentially weighted moving average of the error ratio. The assessment scale of excellent, good, fair, bad, and failed, which indicates the quality of the HVAC control loops, is established as well. The sensitivity analysis for both CQFs is also conducted, and it provides insights on choosing the appropriate parameters to compute such CQFs. Such parameters include the sampling frequency, the length of the moving window, and the variance of the unmeasured disturbance. The field evaluations and tests of the proposed CQFs for simulated control loops and real control loops can be found in the companion paper with the title “Development of Control Quality Factor for HVAC Control Loop Performance Assessment—III: Field Testing and Results (ASHRAE RP-1587).”

Compact Drive Circuit for Capacitive Wireless Power Transfer System Utilizing Leakage-Enhanced Transformer

In capacitively-coupled wireless power transmission (C-WPT), drive circuit topologies with various impedance matching or compensation techniques have been widely investigated in conventional studies, but they tend to increase the circuit complexity and thus offset the simplicity of the energy link structure which is a unique advantage over the inductively-coupled power transmission. In this paper, through systematic considerations on various matching schemes, a compact drive circuit with leakage-enhanced transformer is proposed in order to minimize the circuit volume for the capacitive power transfer system. In the proposed topology, the integrated transformer handles quality factor control as well as reactive compensation. Consequently, it reduces the number of components, the overall system volume, and the voltage stress of the energy link capacitor. The optimal design guideline of the leakage-enhanced transformer is also presented. Comparisons with the conventional method considering the circuit volume and component stress show the advantage of the proposed scheme, and feasibility of the new topology is verified with 10 W prototype hardware.

On-chip Heaters for Tension Tuning of Graphene Nanodrums.

For the study and application of graphene membranes, it is essential to have means to control their resonance frequency and temperature. Here, we present an on-chip heater platform for local tuning of in-plane tension in graphene mechanical resonators. By Joule heating of a metallic suspension ring we show thermomechanical resonance frequency tuning in a few-layer (FL) graphene nanodrum, which is accompanied by an increase in its quality factor, which we attribute to the increase of the in-plane tension. The in situ control of temperature, in-plane tension, resonance frequency, and quality factor of suspended two-dimensional (2D) nanodrums makes this device a unique platform for investigating the origin of dissipation in these ultrathin structures and can be of fundamental importance for studying the thermal properties of 2D materials. Moreover, by simultaneously controlling the heater and the backgate voltage, we can independently control the resonance frequency and quality factor, which is of great importance for applications in sensors and resonant mechanical filters.

Nanomechanical control of optical field and quality factor in photonic crystal structures

Actively controlling the properties of localized optical modes is crucial for cavity quantum electrodynamics experiments. While several methods to tune the optical frequency have been demonstrated, the possibility of controlling the shape of the modes has scarcely been investigated. Yet an active manipulation of the mode pattern would allow direct control of the mode volume and the quality factor and therefore of the radiative processes. In this work, we propose and demonstrate a nano-optoelectromechanical device in which a mechanical displacement affects the spatial pattern of the electromagnetic field. The device is based on a double-membrane photonic crystal waveguide which, upon bending, creates a spatial modulation of the effective refractive index, resulting in an effective potential well or antiwell for the optical modes. The change in the field pattern drastically affects the optical losses: large modulations of the quality factors and dissipative coupling rates larger than 1 GHz/nm are predicted by calculations and confirmed by experiments. This concept opens new avenues in solid-state cavity quantum electrodynamics in which the field, instead of the frequency, is coupled to the mechanical motion.

Silicon nanobeam cavity for ultra-localized light-matter interaction.

In this work, we theoretically and experimentally demonstrate an unusual air mode silicon nanobeam cavity design with dielectric mirrors. This design combines an extremely strong localization of light-matter interaction in the cavity center and a reduced sensitivity of the resonator wavelength to temperature or top cladding material refractive index variations. The proposed approach allows accurate control of the resonator cavity quality factor combined with flexible choice of the cavity effective mode volume. Q-factors higher than 50,000 have been determined for such cavities and mode volumes smaller than (λ/n)3 were achieved in the investigated configurations. Such a cavity design provides a robust approach to study the hybrid integration of various active materials in the silicon platform, including carbon nanotubes, III-V nanowires, graphene, etc., for light emission, modulation, or detection.