Pulsed Power Research Articles

A theoretical study of the output coupler reflectivity effect on the characteristics of Er+3 laser pulse at passively q-switching

The objective of this study deal the effect of the output coupler mirror reflectivity of laser system on behavior and characteristics (duration and energy) of erbium passive Q-switching laser pulse was studied theoretically. In the methods of the study, virtual passive Q-switching laser system consist of major elements such as erbium doped silica as an active medium, Cr+4: YAG crystal used as a saturable absorber, and the mirrors of resonator. Mathematical rate equations model has been used to describe the physical relationship between this element has been solved numerically by Rung - Kutta –Fehlberg method. The results showed regarding the pulse behavior, the increasing value of output coupler mirror reflectivity lead to decreasing of rising and falling time of pulse, so the emission of pulse occur in an advanced time. While regarding the pulse characteristics, the pulse was distinguishable by short duration and high energy, resulting high power of pulse when the output coupler mirror reflectivity increasing. Regarding of results discussion, the study attributes the results to a decrease of the initial and final population inversion density of active medium that results from the increasing value of output coupler mirror reflectivity. Therefore, it is possible to conclude in order to improve the characteristics of erbium passive Q-switching laser pulse; it is appropriate increase the value of output coupler mirror reflectivity within acceptable limits.

Low-noise 2-GHz figure-9 fiber laser based on passive harmonic mode-locking

We have proposed and demonstrated the generation of a high-repetition-rate ultrashort pulse with long-term stability and low noise based on a harmonic mode-locked (HML) figure-9 fiber laser. Different HML orders from the 2nd to the 13th are generated by adjusting the pump power, net dispersion, and wave plate angles. A 2-GHz HML pulse is obtained with a 155-MHz fundamental repetition rate in a Yb-doped fiber laser, and the corresponding supermode suppression level is as high as 50 dB. The average power of the output pulse is nearly 200 mW, and the compressed pulse duration is 535 fs. To the best of our knowledge, 2 GHz and 196 mW represent, respectively, the highest repetition rate and output power in a figure-9 fiber laser. This work offers a potential pathway to achieve high-repetition-rate ultrashort pulses in the GHz range with high power and low noise levels.

Pulse position encoded RZ-OOK transmission for free-space optical communications

This paper proposes a pulse position encoded return-to-zero on-off keying (PP-RZ-OOK) transmission for free space optical (FSO) communications. At the transmitter end, PP-RZ-OOK signal is modulated by encoding the pulse position of RZ-OOK in the symbol duration. At the receiver end, PP-RZ-OOK signal is demodulated by symbol-by-symbol signal estimation. First, the existence of pulse is distinguished by adaptive threshold decision using the channel state information (CSI). Then, with respect to the symbol with the pulse, the knowledge of pulse position is estimated by slot-by-slot pulse power comparison. Finally, PP-RZ-OOK signal is effectively demodulated by both pulse existence and pulse position estimation. Therefore, the spectral efficiency of RZ-OOK is increased by the proposed pulse position encoding technique. The performance of the proposed PP-RZ-OOK modulation was verified through simulations under different turbulence channels and pulse durations, and it was compared with non-return-to-zero OOK (NRZ-OOK) and RZ-OOK modulations. The simulation results demonstrated that the capability of scintillation effect compensation was significantly enhanced compared with NRZ-OOK due to the pulse power increasing. Besides, the spectral efficiency was improved compared with RZ-OOK due to the additional pulse position encoding.

Influence of Detonation Spraying Parameters on the Microstructure and Mechanical Properties of Hydroxyapatite Coatings

The process of osteointegration depends significantly on the surface roughness, structure, chemical composition, and mechanical characteristics of the coating. In this regard, an important direction in the development of medical materials is the development of new techniques of surface modification and the creation of bioactive ceramic coatings. Calcium-phosphate materials based on hydroxyapatite have been proposed as bioactive ceramic coatings on titanium implants for the effective acceleration of bone tissue healing. To obtain bioactive ceramic coatings, pulse power sources are best suited, namely detonation spraying, in which the energy of the explosion of gas mixtures is used as a source of pulse action. The pulse mode of operation in the detonation spraying method is preferable for the formation of bioactive ceramic coatings. It provides a high velocity of hydroxyapatite particles, which promotes their effective fixation on the titanium substrate, while minimizing the heating of the material. This approach preserves the substrate structure and improves the coating adhesion. Four different types of coatings with varying O2/C2H2 molar ratios, ranging from 2.6 to 3.7, were obtained using detonation spraying. Powders and obtained coatings of hydroxyapatite were studied by Raman spectroscopy and XRD structural analysis. The results of XRD phase analysis showed the partial conversion of the hydroxyapatite phase to the α-tricalcium phosphate (α-TCP) phase during the detonation spraying process. The results obtained by Raman spectroscopy indicate that hydroxyapatite is the main phase in coatings. All hydroxyapatite-based coatings exhibited hydrophobic properties, which was confirmed by contact-angle values above 90° in wettability tests, characteristic of hydrophobic surfaces. The adhesive strength of the coatings was measured by the scratch test method. Tribological tests were conducted using the ball-on-disk method under both dry conditions and in Ringer’s solution. This approach enabled the evaluation of wear resistance and friction coefficient of the coatings in different environments, simulating both lubrication-free conditions and those resembling physiological environments.

Development of an inductive energy storage pulsed power supply using SiC semiconductor devices for ozone production by streamer discharges

An inductive energy storage (IES) pulsed power generator driven by a silicon carbide metal oxide semiconductor field effect transistor (SiC-MOSFET) with a blocking voltage of 1.2 kV was developed. The IES pulsed power generator consists of a capacitor, a pulsed transformer and the SiC-MOSFET used as an opening switch. The influence of the turn ratio of the pulsed transformer on the output voltage was evaluated. The output voltage amplitude increased with increasing secondary turn ratio. Under the conditions of no load, a peak output voltage of 13 kV and a pulse width of 120 ns were obtained with a voltage across the drain–source terminals of the MOSFET of 1 kV. The peak voltage increased, and the peak current and pulse width decreased, with increasing load resistance and decreased capacitance. The maximum energy transfer efficiency was obtained at 500 Ω and was approximately 56%.

Effects of ultrasonic treatment and current pulse frequency on properties of micro-arc oxidation coating on Mg alloy LAZ931

To enhance corrosion resistance of magnesium-lithium (Mg-Li) alloy LAZ931 in corrosive environments, a micro-arc oxidation (MAO) based surface treatment was carried out under a unipolar pulsed power supply. Effects of ultrasonic treatment and current pulse frequency on the performance of MAO coatings were investigated using scanning electron microscopy, electrochemical characterization, and friction wear tests. Results demonstrate that ultrasonic treatment greatly reduced the number density of micro-defects in the resulting MAO coatings and improved their overall performance. Corrosion and wear resistance of the MAO coating increased when current pulse frequency increased from 400 to 2000 Hz. Those findings are beneficial for improving the performance of MAO on Mg-Li alloys through optimizing the processing parameters.

A Multi-Module HTS Inductive Pulse Power Supply With Wide Current Pulse Output

A Multi-Module HTS Inductive Pulse Power Supply With Wide Current Pulse Output

A Shunt DC Electric Spring Control Strategy for MVDC Bus Voltage Stability Onboard AES

Background: The recent trend in the all-electric ship (AES) electrical systems, especially in military vessels, is to move towards medium voltage direct current (MVDC) distribution. Bus voltage instability is a major issue in direct current (DC) distribution systems. Nowadays, direct current electric springs (DCES) are extensively used in low-voltage direct current (LVDC) microgrids to address voltage instability issues. This paper extends the use of a shunt DCES to stabilize the bus voltage in an MVDC grid. The work proposes an addition to the MVDC onboard ship distribution system architecture, described in IEEE 1709, by integrating a shunt DCES with a novel control strategy to stabilize the bus voltage under various loading conditions, including propulsion motor (PM) and online pulsed power load (PPL). Methods: The shunt DCES is designed to provide current into the MVDC bus, which reduces the bus current ripple to attain a stable bus voltage with reduced ripple. A dual loop control with a battery management system (BMS) is proposed for the shunt DCES and simulated in MATLAB/Simulink. BMS is designed based on the state of charge (SOC) of the battery and bus current ripple extracted from the system's source and load side currents. The current supplied by the shunt DCES and the extracted ripple current validate the effectiveness of the proposed control. Total harmonic distortions (THDs) as a measure of voltage ripple of the MVDC bus voltage at different intervals are measured and compared for both systems, with and without shunt DCES. Results: It was observed that the shunt DCES could reduce the voltage ripple well below the permissible limit, which is 5% as per IEEE 1709. Conclusion: The proposed control strategy could attain a reduction of 68-85% in THD under peak to off-peak loading conditions with the addition of shunt DCES.

Impact of overvoltage on the mode transition of the spark gap switch: from edge breakdown to stochastic breakdown

Abstract Spark gap switch (SGS) is a fundamental but critical component for large-scale pulsed power devices, whose reliable operation is significantly affected by the breakdown characteristics of SGS. It is observed experimentally that, with the increase of overvoltage, the bridging position of the spark channel transits from edge to stochastic center. In this work, the influence of overvoltage on the breakdown process of a parallel-plate SGS with low geometric distortion of static electric field (<13%) between an atmospheric-pressure air gap of 5 mm is investigated by particle-in-cell/Monte Carlo collision simulation. It is found that, under a low overvoltage (ratio of applied voltage U a to static breakdown voltage U 0, U a/U 0 = 1.5), the streamers at the edge first bridge the gap before that in the central region, due to the field enhancement induced by the electrode curvature. Under higher overvoltage (U a/U 0 = 3), the synchronicity between streamers initiating from the center and those from the edge is greatly improved during the inception stage. After the streamers pass the middle of the gap, the field enhancement at the streamer front is more intensified and promotes the generation of fast electrons. These fast electrons rapidly magnify the difference among the propagating streamers by providing abundant seed electrons ahead of the discharge channel, which leads to the randomness of the bridging position. The results in this work demonstrate the relationship between overvoltage and streamer dynamics, which is beneficial for the performance improvement of SGS.

Coordinated intelligent control strategy and power management for marine gas turbine under pulsed load using optimized neural network

Faced with the challenges of potentially irreversible damage due to instantaneous large pulsed power loads onboard, considering all-electric ship's small power grid capacity and complex gas turbine system, this study proposes a coordinated intelligent control strategy. It utilizes multi-objective optimization neural network to control a validated 20MW ship three-shaft gas turbine, ensuring global optimization tailored to pulsed load variations. Research findings reveal that the gas turbine efficiency at the design point is 32.3%, with a steady-state error within 2.8% and a maximum steady time error of 3.4 seconds, demonstrating acceptable accuracy. Under slope-type pulsed load of 20MW change in 5s, the proposed control strategy effectively manages speed while utilizing the energy storage system to smooth load inputs. It is worth noting that, increasing the fuel flow rate to 1.28 kg/s and inlet guide vane to 5.8 degrees reduces overshoot by 0.7% and rotor steady time by 15.4 seconds. Under transient-type pulsed load of 10MW back and forth change in 5s, the coordinated inlet guide vane control strategy mitigates surge margin and exhaust temperature issues. Adjusting the fuel flow to 1.17 kg/s and inlet guide vane to 9.96 degrees enables the gas turbine to operate within safety boundaries, reducing rotor speed overshoot by 0.4% and steady time by 6.1 seconds. Importantly, the optimized control strategy without energy storage system provides faster and safer dynamic regulation and power transmission for ship acceleration processes under radar load. However, considering only the coordinated strategy of the fuel sub-control loop, it is advisable to avoid compressor surge and over-temperature protection for electromagnetic ejection load scenarios. The research results will lay a valuable technical foundation for the intelligent control and smooth power transfer of the all-electric ship gas turbine power system with pulse loads in the extreme missions of ships in the future.

ICCOS-Based Continuous Inductive Pulse Power Circuit Topology

ICCOS-Based Continuous Inductive Pulse Power Circuit Topology

Multilayer Bionic Tunable Strain Sensor with Mutually Non‐Interfering Conductive Networks for Machine Learning‐Assisted Gesture Recognition

AbstractFlexible strain sensors capable of acquiring tiny mechanical signals and attaching to various irregular surfaces are becoming prevalent in physiological measurement, soft robotics, and human‐machine interaction. However, the advancement of flexible strain sensors is substantially impeded by the intrinsic compromise between sensitivity and the range of detectable signals. Inspired by the multilayer structure of nacre in nature, a carbon nanotubes (CNTs)/graphene (GR)/graphene (GR)/thermoplastic polyurethane (TPU) mat (CGGTM) is prepared by electrospinning and high‐pressure spraying technology. By designing a multilayer structure with mutually non‐interfering conductive networks, the resulting CGGTM possesses a low detection limit (0.05% strain), high sensitivity (gauge factor, GF > 152537), large detection range (up to 364% strain), fast response/recovery time (80 ms/100 ms), and excellent cyclic durability (up to 1000 cycles). Furthermore, the CGGTM also exhibits satisfactory triboelectric performances when assembled into a triboelectric nanogenerator (TENG, 3 × 3 cm2), including high triboelectric output (open‐circuit voltage Voc = 135.4 V, short‐circuit current Isc = 1.25 µA) and power density (88 mW m−2), enabling reliable power supply, self‐powered sensing, and pulse monitoring capability. Finally, CGGTM is successfully applied to the collection of biological signals and multi‐gesture motion recognition assisted by machine learning algorithms, which holds promise for intelligent interaction with gestures in the future.

A Broad-High Temperature Ceramic Capacitor with Local Polymorphic Heterogeneous Structures.

Crafting high-performance dielectrics tailored for pulsed power capacitors, in response to the escalating demands of practical applications, presents a formidable challenge. Herein, this work introduces a novel lineup of lead-free ceramics with local polymorphic heterogeneous structures, defined by the formula (1-x)[0.92BaTiO3-0.08Sr(Mg1/2Ti3/4)O3]-x(Na0.5Bi0.5)TiO3 (BT-SMT-xNBT). This innovative multi-scale synergistic strategy, spanning from the atomic to grain scale, yields materials with a giant recoverable energy density (Wrec) of 10.1 J·cm-3 and an impressive energy efficiency (η) of 95.0%. The integration of linear end elements SMT can significantly mitigate the polarization hysteresis while concurrently boosting the breakdown strength, thus enhancing overall energy efficiency. Furthermore, the inclusion of NBT with high polarization serves to amplify domain size, thereby reinforcing the electric field-induced polarization. This addition also stimulates the creation of polymorphic heterostructures, where tetragonal and rhombohedral nanodomains coexist, as validated by aberration-corrected transmission electron microscopy. Notably, the BT-SMT-0.2NBT ceramics have demonstrated outstanding high-temperature energy storage capabilities, with a Wrec of 7.2 J·cm-3 and an η of 92.2% at 150 °C, along with remarkable broad-temperature stability (ΔWrec, Δη ≤ 4.0%, ≈20-150 °C). These achievements in this work propel the field toward more practical and durable solutions of energy storage dielectrics.

Estimation of Lithium-Ion Battery SOC Based on IFFRLS-IMMUKF

The state of charge (SOC) is a characteristic parameter that indicates the remaining capacity of electric vehicle batteries. It plays a significant role in determining driving range, ensuring operational safety, and extending the service life of battery energy storage systems. Accurate SOC estimation can ensure the safety and reliability of vehicles. To tackle the challenge of precise SOC estimation in complex environments, this study introduces an improved forgetting factor recursive least squares (IFFRLS) method, which integrates the Golden Jackal optimization (GJO) algorithm with the traditional FFRLS method. This integration is grounded in the formulation of a lithium battery state equation derived from a second-order RC equivalent circuit model. Additionally, the research utilizes the interactive multiple model unscented Kalman filter (IMMUKF) algorithm for SOC estimation, with experimental validation conducted under various conditions, including hybrid pulse power characterization (HPPC), urban dynamometer driving schedule (UDDS), and real underwater scenarios. The experimental results demonstrate that the SOC estimation method of lithium batteries based on IFFRLS-IMMUKF exhibits high accuracy and a favorable temperature applicability range.

Passively Mode-Locked Erbium-Doped Fiber Laser and Application in Laser Thrombolysis

Fiber lasers have been widely used in surgery with the development of fiber photonics. Since the human body is prone to myocardial infarction caused by blood clots, laser thrombolysis was proposed as a safe and efficient treatment. Mode-locked fiber lasers have high peak power and narrow pulse width. In order to observe the effect of laser thrombolysis with mode-locked fiber lasers, a 1.5 µm mode-locked fiber laser based on carbon nanotubes was built, showing a pulse width of 1.46 ps, a 3 dB bandwidth of 1.65 nm, and a repetition rate of 29.5 MHz. The output pulses were amplified by an erbium-doped fiber amplifier to the hundred-milliwatt level and were applied to the surface of a self-made thrombus. The influences of lasing power and time on the damage diameter of the thrombus surface were evaluated. A low threshold damage power of 45 mW was observed, which resulted from the high peak power of the mode-locked pulses. These results demonstrate that high ablation efficiency can be achieved by using mode-locked pulses with a narrow pulse width and high peak power.

An enhanced electrokinetic system for remediation of Cu-polluted clay soils by integrating purging solutions and intermittent power

This study investigated the effectiveness and underlying mechanisms of purging solutions enhanced by intermittent power in improving electrokinetic (EK) restoration of clay soils even under high levels of heavy metals (HM). In so doing, the artificially contaminated specimens containing a wide range of copper (Cu) were prepared and then subjected to a series of EK tests with various electrolytes and electric regimes. Macro and micro scale examinations revealed that under the unenhanced EK condition (i.e., continuous current without agents), the formation of non-conducting solid phases and/or the clogged fabric in the samples with the high dosages (> 250 mg/kg) of HM could dramatically impede the metal separation from the soil. Hence, increasing the remediation time would not be very effective in facilitating the decontamination process. It was observed that the EDTA-ameliorated treatment accompanied by pentetic acid and acetic acid can mitigate the metal precipitation/encapsulation effects induced by EK actions, resulting in improved rate of HM removal. In this case; however, a high portion of these enhancers would be required to ensure the stable mobility of ions and to achieve successful recovery. Such a limitation has been shown to be overcome by incorporating pulsed power (PP) at an optimal frequency. In fact, as evidenced by SEM-EDX and XRD analyses, the integration of chemical agents with PP could simultaneously retain the solubilized Cu species in the soil mass and modify the matrix tortuosity (i.e., the establishment of well-linked pores), two features that have been found to play essential roles in providing for favorable activity of HM ions during the EK operation. The corresponding refinements in the binary system would cause an almost 8 folds increase in the removal efficiency and a shorter (up to 30 %) time of treatment compared to conventional EK.

Effect of thermal shock on energy density of biaxially oriented polypropylene films for pulsed power capacitors

In this paper, thermal shock experiments are performed on the biaxially oriented polypropylene (BOPP) films, and the changes in dielectric and energy storage properties before and after the experiments are explored. The experimental results show that the films have reduced comprehensive performance with the thermal shock time and frequency increasing. After the thermal shock, both the permittivity and the dielectric loss increase slightly. And, the direct current (DC) conductivity has risen by 73.6%–714.2%. The lowest DC breakdown strength of film is 604.4 kV mm−1, showing a 13.5% reduction compared to that of pristine film. In addition, energy storage performance has also deteriorated. The maximum discharge energy density decreased from 4.62 J cm−3 of pristine film to 3.26 J cm−3 of treated film. There is a decrease in charge and discharge efficiency under the same electric field. The metallization layer of the film receives less influence; the capacitance is reduced by only 0.37%. The causes and mechanisms of performance changes are analyzed and discussed. The disruption of molecular chains during thermal shock is the most important factor leading to the degradation of films. This paper provides a powerful perspective and reference for studying the performance degradation and failure of polymer dielectrics under extreme operating conditions.

Spectral and optic-metric methods of monitoring parameters of plasma channels caused by discharge currents between metals granules in working liquids

Introduction. Spark-erosion processing of metals and alloys granules in working liquids is the basis of a several technological processes. Efficiency of energy use in them and parameters of the resulting product largely depend on the accuracy of stabilization and regulation of pulse power in each plasma channel between the granules. To achieve this, until now only the voltage and current of the discharge pulses in the entire layer of granules have been controlled. Problem. The measurement methods, which are used, are not effective enough for monitoring the parameters of individual plasma channels and predicting the size distribution of eroded metals particles at the stage of their formation. The aim of the work is to develop a method for determining the volumes of components of plasma channels in layers of metals granules during their spark-erosion treatment to predict the size distribution of eroded metal particles at the stage of their formation, as well as to simplify the method of spectrometric analysis of the elemental composition of substances surrounding plasma channels for the operational prediction of the chemical composition of resulting products. Methodology. A series of experiments were carried out on spark-erosion processing of Al and Ag granules layers in distilled water. Using a digital camera, images of the plasma channels in them were obtained. Based on the theory of pulsed electrical breakdown of liquid dielectrics, an analysis of the components of plasma channels was carried out. Using the specialized ToupView program, the volumes of equivalent ellipsoids of rotation were determined, approximating the halos of colored radiation likely arising from streamers, as well as the spark cores of plasma channels emitting white light. The shades of the resulting radiation were studied for several metals and working liquids. The obtained data were compared with the known results of spectrometric studies for the same elements excited by similar mechanisms. Results. The theory of discharge-pulse systems for spark-erosion processing of granular conductive media has been developed in the direction of new methods for monitoring the parameters of discharge pulses and predicting the chemical composition and size distribution parameters of eroded metal particles at the stage of their production. An optic-metric method has been developed for determining the volumes of halos and cores of plasma channels. A simplified spectral method for determining the chemical composition of erosion particles based on the shade of the resulting radiation was proposed. Originality. The developed new optic-metric method makes it possible to obtain information about almost every plasma channel, which refines predictions of the size distribution of erosion particles. To implement the method, general-purpose hardware and specialized software that is freely available are used. The developed method of simplified spectral analysis of excited atoms makes it possible to make preliminary predictions of the chemical composition of the obtained erosion particles already at the stage of their formation without the use of expensive specialized equipment. Practical significance. The ratio of the volumes of halos and cores of plasma channels between Al and Ag granules in distilled water was measured. An analysis of the emission spectra of plasma channel halos between Al, Ag and Cu granules in distilled water, Fe in ethyl alcohol, Ni-Mn-Ga and Ti-Zr-Ni alloys in liquid nitrogen, and Ti-Zr-Ni in liquid argon was carried out. Based on spectrometry data, the resulting shades of these radiations were substantiated and their description in the RGB system is given. References 56, table 1, figures 4.

Improving the Energy Storage Performance in Bi0.5Na0.5TiO3-Based Ceramics by Combining Relaxor and Antiferroelectric Properties.

Ceramic capacitors have received great attention for use in pulse power systems owing to their ultra-fast charge-discharge rate, good temperature stability, and excellent fatigue resistance. However, the low energy storage density and low breakdown strength (BDS) of ceramic capacitors limit the practical applications of energy storage technologies. In this work, we present a series of relaxor ferroelectric ceramics (1-x) [0.94 Bi0.5Na0.5TiO3 -0.06BaTiO3]- x Sr0.7Bi0.2TiO3 (1-x BNT-BT- x SBT; x = 0, 0.20, 0.225, 0.25, 0.275 and 0.30) with improved energy storage performances by combining relaxor and antiferroelectric properties. XRD, Raman spectra, and SEM characterizations of BNT-BT-SBT ceramics revealed a rhombohedral-tetragonal phase, highly dynamic polar nanoregions, and a reduction in grain size with a homogeneous and dense microstructure, respectively. A high dielectric constant of 1654 at 1 kHz and low remnant polarization of 1.39 µC/cm2 were obtained with the addition of SBT for x = 0.275; these are beneficial for improving energy storage performance. The diffuse phase transition of these ceramics displays relaxor behavior, which is improved with SBT and confirmed by modified the Curie-Weiss law. The combining relaxor and antiferroelectric properties with fine grain size by the incorporation of SBT enables an enhanced maximum polarization of a minimized P-E loop, leading to an improved BDS. As a result, a high recoverable energy density Wrec of 1.02 J/cm3 and a high energy efficiency η of 75.98% at 89 kV/cm were achieved for an optimum composition of 0.725 [0.94BNT-0.06BT]-0.275 SBT. These results demonstrate that BNT-based relaxor ferroelectric ceramics are good candidates for next-generation ceramic capacitors and offer a potential strategy for exploiting novel high-performance ceramic materials.

Modulating lifetime distribution through variable excitation pulse length and power: a case study on colloidal PbS quantum dots

Modulating lifetime distribution through variable excitation pulse length and power: a case study on colloidal PbS quantum dots