Pseudo Random Bit Sequence Data Research Articles

Where Tape and Hard-Disk Technology Meet: The HDD Head–Tape Interface

In this paper, we study the mechanical interface between a hard-disk drive (HDD) head and magnetic recording tape to enable the use of HDD heads to investigate future tape operating points. Tape surface height measurements were obtained using an interferometer microscope for varying wrap angle configurations, tape velocities, and tape tensions. Simultaneously, the readback signal from the read element of the HDD head was captured to study the quality of the contact between the tape and the head. The signal-to-noise ratio (SNR) and bit-error rate (BER) performance of pseudorandom bit sequence (PRBS) data readback experiments are presented. An analytical model is described for estimating the magnetic spacing from the PRBS readback spectrum. In contrast to current commercial tape heads, the HDD head surface has a pronounced topography containing cavities. When tape passes in close proximity, subambient pressures are formed inside these cavities and the resulting pressure differences force the tape toward the head and deform the tape into remarkable shapes. For the topography of the HDD head used, the shape of tape is predominantly determined by the leading and trailing wrap angles. Readback was obtained only in the backward direction (i.e., opposite to the direction of operation in an HDD), with positive leading but negative trailing wrap angles. Better readback is obtained for shallow wrap angles, lower tape velocity, and higher tape tension. Good readback is obtained for leading and trailing wrap angles ~0.3° and -0.2°, respectively. Fits of the analytical model to the spectrum of the readback signal of PRBS data lead to a magnetic spacing estimate of ~30 nm. At 600 kb/in linear density, we measured 11 dB SNR and 7 × 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-3</sup> BER for PRBS data on perpendicularly oriented particulate barium-ferrite tape.

Ultrafast and bias-free all-optical wavelength conversion using III-V-on-silicon technology

Using a 7.5 μm diameter disk fabricated with III-V-on-silicon fabrication technology, we demonstrate bias-free all-optical wavelength conversion for non-return-to-zero on-off keyed pseudorandom bit sequence (PRBS) data at the speed of 10 Gbits/s with an extinction ratio of more than 12 dB. The working principle of such a wavelength converter is based on free-carrier-induced refractive index modulation in a pump-probe configuration. We believe it to be the first bias-free on-chip demonstration of all-optical wavelength conversion using PRBS data. All-optical gating measurements in the pump-probe configuration with the same device have revealed that it is possible to achieve wavelength conversion beyond 20 Gbits/s.

A Full On-Chip CMOS Clock-and-Data Recovery IC for OC-192 Applications

In this paper, a fully integrated OC-192 clock-and-data recovery (CDR) architecture in standard 0.18-mum CMOS is described. The proposed architecture integrates the typically large off-chip filter capacitor by using two feed-forward paths configuration to generate zero and pole and satisfies SONET jitter requirements with a total power dissipation (including the buffers) of 290 mW. The measured RMS jitter of the recovered data is 0.74 ps with a bit-error rate less than 10-12 when the input pseudorandom bit sequence (PRBS) data pattern has a pattern length of 215 - 1 and a total horizontal eye closure of 0.54 peak-to-peak unit interval (Ulpp) due to the added intersymbol interference distortion by passing data through 9-in FR4 printed circuit board trace. The chip exceeds SONET OC-192 jitter tolerance mask, and high-frequency jitter tolerance is over 0.31 Ulpp by applying PRBS data with a pattern length of 231 - 1.

DFB 반사기가 집적된 다중전극 레이저 다이오드를 이용한 RZ 및 NRZ 데이터 신호의 광클럭 재생

We have extracted an optical clock signal from a return-to-zero(RZ) pseudorandom bit sequence(PRBS) and non-return-to-zero(NRZ) PRBS data in a pulsation multi-section laser diode with DFB reflector. The ms timing jitter achieved less than 1 ps for the input 11.727 Gbit/s RZ PRBS and NRZ PRBS data. The PRE data wasconverted from the NRZ data using an NRZ to pseudo-return to zero(PRZ) converter module. The optical clock was extracted from the PRZ data which contains the clock components. Although the input PRZ data gives a timing jitter of 2 ps, the extracted clock has timing jitter of 1 ps.