Properties Of Human Trabecular Bone Research Articles

Modeling of the dielectric properties of trabecular bone samples at microwave frequency

In this paper, the dielectric properties of human trabecular bone are evaluated under physiological condition in the microwave range. Assuming a two components medium, simulation and experimental data are presented and discussed. A special experimental setup is developed in order to deal with inhomogeneous samples. Simulation data are obtained using finite difference time domain from a realistic sample. The bone mineral density of the samples are also measured. The simulation and experimental results of the present study suggest that there is a negative relation between bone volume fraction (BV/TV) and permittivity/conductivity: the higher the BV/TV, the lower the permittivity/conductivity. This is in agreement with the recently published in vivo data.

Dependence of mechanical properties of trabecular bone on plate–rod microstructure determined by individual trabecula segmentation (ITS)

Individual trabecula segmentation (ITS) technique can decompose the trabecular bone network into individual trabecular plates and rods and is capable of quantifying the plate/rod-related microstructural characteristics of trabecular bone. This novel technique has been shown to be able to provide in-depth insights into micromechanics and failure mechanisms of human trabecular bone, as well as to distinguish the fracture status independent of area bone mineral density in clinical applications. However, the plate/rod microstructural parameters from ITS have never been correlated to experimentally determined mechanical properties of human trabecular bone. In this study, on-axis cylindrical trabecular bone samples from human proximal tibia (n=22), vertebral body (n=10), and proximal femur (n=21) were harvested, prepared, scanned using micro computed-tomography (µCT), analyzed with ITS and mechanically tested. Regression analyses showed that the plate bone volume fraction (pBV/TV) and axial bone volume fraction (aBV/TV) calculated by ITS analysis correlated the best with elastic modulus (R2=0.96–0.97) and yield strength (R2=0.95–0.96). Trabecular plate-related microstructural parameters correlated highly with elastic modulus and yield strength, while most rod-related parameters were found inversely and only moderately correlated with the mechanical properties. In addition, ITS analysis also identified that trabecular bone at human femoral neck had the highest trabecular plate-related parameters while the other sites were similar with each other in terms of plate–rod microstructure.

Within subject heterogeneity in tissue-level post-yield mechanical and material properties in human trabecular bone

The ability to determine patient-specific mechanical properties of trabecular bone is needed for a reliable estimation of fracture risks. Tissue mechanics and material composition are important factors that contribute to trabecular bone performance, but only a few studies have investigated the post-yield behaviour of human trabecular bone, and limited knowledge for modelling is available about ultimate properties needed.Aim of this paper was to investigate absolute values and deviation of mechanical and material properties of human trabecular bone at the tissue level, in a healthy and osteoporotic donor. A combination of tensile and bending tests of single trabeculae up to failure, μCT measurement of sample geometry and finite element analysis were incorporated to determine mechanical properties. The samples were analysed with Raman spectroscopy to evaluate the material composition. High within-subject variability was found, for both the healthy and osteoporotic donor. Nevertheless, the two donors could be separated by analysing the ultimate strain and post-yield work, as well as two of the material parameters (B-type carbonate substitution ratio and collagen cross-link ratio). It indicates that tissue level properties seem to be relevant also for macroscopic mechanical behaviour. These findings also suggest that the mechanical variability for the inelastic region at the tissue level may be associated with varying material properties, while until yielding occurs our data does not suggest any connection between the mechanical and the investigated material. Finally, a set of mechanical properties of human bone have been reported that are a relevant reference for computational studies and FE analysis.

Accuracy of individual trabecula segmentation based plate and rod finite element models in idealized trabecular bone microstructure.

Currently, specimen-specific micro finite element (μFE) analysis based micro computed tomography (μCT) images have become a major computational tool for the assessment of the mechanical properties of human trabecular bone. Despite the fine characterization of the three-dimensional (3D) trabecular microstructure based on high-resolution μCT images, conventional μFE models with each voxel converted to an element are not efficient in predicting the nonlinear failure behavior of bone due to a prohibitive computational cost. Recently, a highly efficient individual trabecula segmentation (ITS)-based plate and rod (PR) modeling technique has been developed by substituting individual plates and rods with shell and beam elements, respectively. In this technical brief, the accuracy of novel PR μFE models was examined in idealized microstructure models over a broad range of trabecular thicknesses. The Young's modulus and yield strength predicted by simplified PR models strongly correlated with those of voxel models at various voxel sizes. The conversion from voxel models to PR models resulted in an ∼762-fold reduction in the largest model size and significantly accelerated the nonlinear FE analysis. The excellent predictive power of the PR μFE models, demonstrated in an idealized trabecular microstructure, provided a quantitative mechanical basis for this promising tool for an accurate and efficient assessment of trabecular bone mechanics and fracture risk.

The Role of Fabric in the Large Strain Compressive Behavior of Human Trabecular Bone

Osteoporosis-related vertebral body fractures involve large compressive strains of trabecular bone. The small strain mechanical properties of the trabecular bone such as the elastic modulus or ultimate strength can be estimated using the volume fraction and a second order fabric tensor, but it remains unclear if similar estimations may be extended to large strain properties. Accordingly, the aim of this work is to identify the role of volume fraction and especially fabric in the large strain compressive behavior of human trabecular bone from various anatomical locations. Trabecular bone biopsies were extracted from human T12 vertebrae (n=31), distal radii (n=43), femoral head (n=44), and calcanei (n=30), scanned using microcomputed tomography to quantify bone volume fraction (BV/TV) and the fabric tensor (M), and tested either in unconfined or confined compression up to very large strains (∼70%). The mechanical parameters of the resulting stress-strain curves were analyzed using regression models to examine the respective influence of BV/TV and fabric eigenvalues. The compressive stress-strain curves demonstrated linear elasticity, yielding with hardening up to an ultimate stress, softening toward a minimum stress, and a steady rehardening followed by a rapid densification. For the pooled experiments, the average minimum stress was 1.89 ± 1.77 MPa, while the corresponding mean strain was 7.15 ± 1.84%. The minimum stress showed a weaker dependence with fabric as the elastic modulus or ultimate strength. For the confined experiments, the stress at a logarithmic strain of 1.2 was 8.08 ± 7.91 MPa, and the dissipated energy density was 5.67 ± 4.42 MPa. The latter variable was strongly related to the volume fraction (R(2)=0.83) but the correlation improved only marginally with the inclusion of fabric (R(2)=0.84). The influence of fabric on the mechanical properties of human trabecular bone decreases with increasing strain, while the role of volume fraction remains important. In particular, the ratio of the minimum versus the maximum stress, i.e., the relative amount of softening, decreases strongly with fabric, while the dissipated energy density is dominated by the volume fraction. The collected results will prove to be useful for modeling the softening and densification of the trabecular bone using the finite element method.

Ultrasound Backscatter Imaging Provides Frequency-Dependent Information on Structure, Composition and Mechanical Properties of Human Trabecular Bone

The strength as well as the acoustic properties of trabecular bone are determined by its structure and composition. Consequently, tissue structure and compositional properties also affect the ultrasound propagation in bone. The diagnostic potential of ultrasound has not been fully exploited in clinical quantitative ultrasound devices. The aim of this study was to investigate the ability of quantitative ultrasound pulse-echo imaging, conducted over a broad range of frequencies (1 to 5 MHz), to predict the mechanics, composition and microstructure of trabecular bone. Ultrasound reflection and backscatter parameters correlated significantly with the ultimate strength of the trabecular bone and the bone volume fraction ( r = 0.76–0.90, n = 20, p < 0.01). Ultrasound backscatter associated significantly (independently of bone structure or mineral content) with the collagen content of the bone matrix ( r = 0.75, r adjusted = 0.66, p < 0.01). Interestingly, the applied ultrasound frequency seemed to relate the sensitivity of ultrasound backscatter to different properties of trabecular bone. At frequencies ranging from 1 to 3.5 MHz, the ultrasound backscatter associated significantly with the tissue mechanical and structural parameters. At 5 MHz, the composition of the bone matrix was a more significant determinant of the measured backscatter. This study provides useful information for optimizing the use of pulse-echo measurements, and thereby further emphasizes the diagnostic potential of the ultrasound backscatter measurements of trabecular bone.

Multi-axial mechanical properties of human trabecular bone

In the context of osteoporosis, evaluation of bone fracture risk and improved design of epiphyseal bone implants rely on accurate knowledge of the mechanical properties of trabecular bone. A multi-axial loading chamber was designed, built and applied to explore the compressive multi-axial yield and strength properties of human trabecular bone from different anatomical locations. A thorough experimental protocol was elaborated for extraction of cylindrical bone samples, assessment of their morphology by micro-computed tomography and application of different mechanical tests: torsion, uni-axial traction, uni-axial compression and multi-axial compression. A total of 128 bone samples were processed through the protocol and subjected to one of the mechanical tests up to yield and failure. The elastic data were analyzed using a tensorial fabric-elasticity relationship, while the yield and strength data were analyzed with fabric-based, conewise generalized Hill criteria. For each loading mode and more importantly for the combined results, strong relationships were demonstrated between volume fraction, fabric and the elastic, yield and strength properties of human trabecular bone. Despite the reviewed limitations, the obtained results will help improve the simulation of the damage behavior of human bones and bone-implant systems using the finite element method.

Spatial variation of acoustic properties is related with mechanical properties of trabecular bone

In clinical applications, ultrasound parameters are measured as an average value over a region of interest (ROI) or as a value at a single measurement point. Due to natural adaptation to loading conditions, trabecular bone is structurally, compositionally and mechanically heterogeneous and anisotropic. Thus, spatial variation of ultrasound parameters within ROI may contain valuable information on the mechanical integrity of trabecular bone. However, this issue has not been thoroughly investigated. In the present study, we aimed at investigating the significance of the spatial variation of ultrasound parameters for the prediction of mechanical properties of human trabecular bone. For this aim, parametric maps of apparent integrated backscattering (AIB), integrated reflection coefficient (IRC), speed of sound (SOS), average attenuation (AA) and normalized broadband ultrasound attenuation (nBUA) were calculated for femoral and tibial bone cylinders (n = 19–20). Further, the effect of time window length on the AIB, variation of AIB within ROI and association between AIB and bone mechanical properties were characterized. Based on linear correlation analysis, spatial variation of AIB, assessed as standard deviation of measurements within ROI, was a strong predictor of bone ultimate strength (r = −0.82, n = 19, p < 0.01). Further, the time window length affected absolute values of AIB and strength of correlation between AIB and bone ultimate strength. Interestingly, linear combination of mean IRC and spatial variation of AIB within ROI was the strongest predictor of bone ultimate strength (r = 0.92, n = 19, p < 0.01). In conclusion, our findings suggest that the measurement of two-dimensional parametric maps of ultrasound parameters could yield information on bone status not extractable from single point measurements. This highlights the potential of parametric imaging in osteoporosis diagnostics.

The role of fabric in the quasi-static compressive mechanical properties of human trabecular bone from various anatomical locations

Osteoporosis leads to an increased risk of bone fracture. While bone density and architecture can be assessed in vivo with increasing accuracy using CT and MRI, their relationship with the critical mechanical properties at various anatomical sites remain unclear. The objective of this study was to quantify the quasi-static compressive mechanical properties of human trabecular bone among different skeletal sites and compare their relationships with bone volume fraction and a measure of microstructural anisotropy called fabric. Over 600 trabecular bone samples from six skeletal sites were assessed by microCT and tested in uniaxial compression. Bone volume fraction correlated positively with elastic modulus, yield stress, ultimate stress, and the relationships depended strongly on skeletal site. The account of fabric improved these correlations substantially, especially when the data of all sites were pooled together, but the fabric-mechanical property relationships remained somewhat distinct among the anatomical sites. The study confirms that, beyond volume fraction, fabric plays an important role in determining the mechanical properties of trabecular bone and should be exploited in mechanical analysis of clinically relevant sites of the human skeleton.

Orthogonal Properties of Human Trabecular Bone by Spherical Indentation Test

The elastic modulus and the apparent density of the trabecular bone were evaluated from spherical indentation tests and Computed Tomography and their relationship was quantified. After the femurs were prepared and embedded with respect to their anatomical orientation, the transverse planes of the trabecular bone specimens were scanned at 1mm intervals using a CT scanner. The metaphyseal regions were sectioned with a diamond-blade saw, producing 8mm cubes. Using a custom-made spherical indentation tester, the cubes were mechanically tested in the anteriorposterior (AP), medial-lateral (ML), and inferior-superior (IS) directions. After determination of modulus from the mechanical testing, the apparent densities of the specimens were measured. The results showed that the IS modulus was significantly greater than both the AP and ML moduli with the AP modulus greater than the ML modulus. This demonstrated that orthogonality was a structural characteristic of the trabecular bone. The power relationship between the modulus and the apparent density was also found to be statistically significant.

Prediction of density and mechanical properties of human trabecular bone in vitro by using ultrasound transmission and backscattering measurements at 0.2–6.7 MHz frequency range

The ultrasound (US) backscattering method has been introduced as an alternative for the through-transmission measurement of sound attenuation and speed in diagnosis of osteoporosis. Both attenuation and backscattering depend strongly on the US frequency. In this study, 20 human trabecular bone samples were measured in transmission and pulse-echo geometry in vitro. The aim of the study was to find the most sensitive frequency range for the quantitative ultrasound (QUS) analyses. Normalized broadband US attenuation (nBUA), speed of sound (SOS), broadband US backscatter (BUB) and integrated reflection coefficient (IRC) were determined for each sample. The samples were spatially scanned with five pairs of US transducers covering a frequency range of 0.2–6.7 MHz. Furthermore, mechanical properties and density of the same samples were determined. At all frequencies, SOS, BUB and IRC showed statistically significant linear correlations with the mechanical properties or density of human trabecular bone (0.51 < r < 0.82, 0.54 < r < 0.81 and 0.70 < r < 0.85, respectively). In contrast to SOS, IRC and BUB, nBUA showed statistically significant correlations with mechanical parameters or density at the centre frequency of 1 MHz only. Our results suggest that frequencies up to 5 MHz can be useful in QUS analyses for the prediction of bone mechanical properties and density. Since the use of higher frequencies provides better axial and spatial resolution, improved structural analyses may be possible. While extensive attenuation of high frequencies in trabecular bone limits the clinically feasible frequency range, selection of optimal frequency range for in vivo QUS application should be carefully considered.

Prediction of mechanical properties of human trabecular bone by electrical measurements

In trabecular bone, the interrelationships of electrical and dielectric properties with mechanical characteristics are poorly known. Information on these relations is crucial for evaluation of the diagnostic potential of impedance techniques. In this study, electrical and dielectric properties, i.e. permittivity, conductivity, phase angle, loss factor, specific impedance and dissipation factor of human trabecular bone samples (n = 26, harvested from the distal femur and proximal tibia) were characterized in a wide frequency range (50 Hz–5 MHz). Mechanical properties, i.e. Young's modulus, ultimate strength, yield stress, yield strain and resilience of the samples (n = 20) were determined by using destructive compressive testing. Subsequently, measurements of electrical and dielectric properties were repeated after mechanical testing. The measurements were also repeated for the control samples (n = 6) that were not mechanically tested. Electrical, dielectric or mechanical properties showed no significant differences between the intact femoral and tibial samples. The electrical and dielectric parameters as well as the linear correlations between the dielectric and electrical parameters with mechanical parameters were strongly frequency dependent. At the frequency of 1.2 MHz, the relative permittivity showed the strongest linear correlations with the Young's modulus (r = 0.71, p < 0.01, n = 20) and ultimate strength (r = 0.73, p < 0.01, n = 20). Permittivity and dissipation factor showed statistically significant changes after mechanical testing. Our results suggest that the measurements of low frequency electrical and dielectric properties may provide information on the mechanical status of trabecular bone and, possibly, may even help to diagnose bone microdamage. In the future, these measurement techniques may be further developed for use during open surgery, such as bone grafting or total hip replacement surgery.

A review of morphology–elasticity relationships in human trabecular bone: theories and experiments

In the perspective of predicting mechanical from morphological properties of human trabecular bone, the theoretical and experimental relationships between volume fraction, fabric and elastic properties were reviewed. Five data sets of human trabecular bone and two data sets of idealized cells were obtained from various investigators and analyzed statistically with one isotropic and four anisotropic models. For each model, multiple linear regressions were performed to fit the components of both the compliance and the stiffness tensors using volume fraction and in some cases fabric. The adjusted coefficients of determination of the regressions and the average relative errors of the reported versus the predicted tensor norms were calculated. The three anisotropic models that implied a log transformation of the data showed the best results. Excluding the idealized cell data, the adjusted coefficients of determination of these models ranged from 0.80 to 0.95 for the compliance and from 0.80 to 0.94 for the stiffness tensors, while the average relative errors varied between 16% and 55% for the compliance and between 25% and 62% for the stiffness data. The use of volume fraction alone in the isotropic model decreased the adjusted coefficients of determination by 0.03–0.25 and increased the average relative errors by 5–27%. This review confirms the potential of morphology–elasticity relationships for estimation of elastic properties of human trabecular bone using peripheral quantitative computed tomography or magnetic resonance imaging, but emphasizes the need for standardized measurements of mechanical properties at both continuum and tissue level.

A global relationship between trabecular bone morphology and homogenized elastic properties.

An alternative concept of the relationship between morphological and elastic properties of trabecular bone is presented and applied to human tissue from several anatomical locations using a digital approach. The three-dimensional morphology of trabecular bone was assessed with a microcomputed tomography system and the method of directed secants as well as the star volume procedure were used to compute mean intercept length (MIL) and average bone length (ABL) of 4 mm cubic specimens. Assuming isotropic elastic properties for the trabecular tissue, the general elastic tensors of the bone specimens were determined using the homogenization method and the closest orthotropic tensors were calculated with an optimization algorithm. The assumption of orthotropy for trabecular bone was found to improve with specimen size and hold within 6.1 percent for a 4 mm cube size. A strong global relationship (r2 = 0.95) was obtained between fabric and the orthotropic elastic tensor with a minimal set of five constants. Mean intercept length and average bone length provided an equivalent power of prediction. These results support the hypothesis that the elastic properties of human trabecular bone from an arbitrary anatomical location can be estimated from an approximation of the anisotropic morphology and a prior knowledge of tissue properties.

Evaluation of orthogonal mechanical properties and density of human trabecular bone from the major metaphyseal regions with materials testing and computed tomography

We evaluated the orthogonal mechanical properties of human trabecular bone from the major metaphyseal regions with materials testing and quantitative computed tomography (CT). The proximal tibia, distal femur, proximal femur, distal radius, and proximal humerus from fresh cadaver specimens between the ages of 55 and 70 years were excised and prepared for experimentation. The bones were embedded and scanned at 1 or 1.5 mm intervals on a Technicare HPS 1440 and GE 9800 CT scanner. After scanning, the bones were sectioned, producing 8-mm cubes of trabecular bone which were mechanically tested in uniaxial compression at a strain rate of 1%. The testing sequence consisted of preyield tests in two of the three orthogonal directions and failure in the third. After testing, the cubes were evaluated for apparent density and ash weight. The results of the study show that the strength and stiffness of trabecular bone varies significantly within metaphyseal regions and from metaphysis to metaphysis. The power and significance of relationships between density and modulus varied as a function of metaphyseal location. Both linear and nonlinear models were significant, suggesting that trabecular deformation occurs in response to both axial and bending loads. Finally, the need for architectural measures of trabecular bone to predict mechanical properties is emphasized.