Properties Of Denture Base Material Research Articles

Flexural strength, fracture toughness, translucency, stain resistance, and water sorption of 3D-printed, milled, and conventional denture base materials.

To compare mechanical, optical, and physical properties of denture base materials fabricated with various 3D printing systems to reference milled and conventionally heat-processed denture base materials. Specimens of denture base materials were either 3D-printed (DLP in-office printer, CLIP laboratory printer, or material jetting laboratory printer), milled, or heat processed. 3-point bend flexural strength testing was performed after 50 hours of water storage following 1hour of drying (dry testing) or in 37°C water (wet testing). Fracture toughness was performed with a notched beam specimen after 7 days of water storage and tested dry. The translucency parameter was measured with 2mm thick specimens. Stain resistance was measured as color change following 14 days of storage in 37°C coffee. Water sorption was measured following 7 days of storage in 37°C distilled water. For dry testing, all but one of the 3D-printed materials attained higher or equivalent flexural strength as the reference materials. For wet testing, all 3D-printed materials attained higher or equivalent strength as the reference materials and dry-tested materials. For 3D-printed materials, wet testing increased displacement before fracture whereas it decreased displacement for the reference materials. Only two of the 3D-printed materials had similar fracture toughness as the reference materials. One of the 3D-printed materials was more translucent and one was more opaque than the reference materials. Only one of the 3D-printed materials absorbed more water than the reference materials. 3D-printed denture base materials have mostly equivalent mechanical, optical, and physical properties to conventional and milled denture base materials.

Biological, Antifungal, and Physical Efficacy of a Denture Cleanser Formulated with Cnidium officinale Extracts.

We aimed to assess the antifungal efficacy and impact of a denture cleanser containing Cnidium officinale extract on the surface characteristics of denture base materials, as well as its physical and biological properties. The experimental denture cleansers were formulated with C. officinale at concentrations of 100 and 150 μg/mL, combined with 1% cocamidopropyl betaine as a natural surfactant. Antifungal efficacy was evaluated using zone-of-inhibition assays against Candida albicans, revealing inhibition zones of 20 ± 1.8 mm for the 100 μg/mL concentration and 23.6 ± 1.6 mm for the 150 μg/mL concentration. Surface property assessments-including hardness, roughness, color stability, and solubility measurements-demonstrated no significant differences compared to the control group. Biological evaluations included the quantification of polyphenol and flavonoid content. The C. officinale-based cleanser showed significant antifungal activity without affecting the hardness, roughness, color stability, or solubility of denture base materials. Biological tests revealed no cytotoxicity and minimal mucosal irritation. Polyphenol and flavonoid contents were quantitatively measured, revealing higher concentrations in the experimental groups, which were correlated with significant antifungal activity. These compounds are known for their roles in disrupting microbial processes and enhancing antimicrobial effects. These findings suggest that the C. officinale-based denture cleanser effectively inhibits C. albicans while preserving the physical properties of denture base materials. This study highlights the potential of C. officinale in denture cleanser formulations, promoting denture hygiene and oral health. Future research should prioritize long-term clinical evaluations and formulation optimization.

Effect of Adding Different Concentrations of Silver Nanoparticles on Flexural Strength and Microhardness of Different Denture Base Materials.

This study aimed to evaluate the effect of adding different concentrations of silver nanoparticles (AgNPs) on the flexural strength and microhardness of various denture base materials. For this study, a total of 60 specimens were used and divided into equal groups. The first group consisted of heat-cured acrylic resin (Vertex-Germany), while the second group consisted of thermoplastic resin (Breflex 2nd edition, Germany). The samples were created using a split brass mold with dimensions of 65 × 10 × 2.5 mm, in accordance with the specifications of the American Dental Association (specifically No. 12 for flexural and microhardness). Following this, the samples were divided into three groups (A, B, and C) based on different concentrations of AgNPs (0, 2, and 5%). The flexural and microhardness of the samples were assessed using a universal testing machine and the Vickers hardness test, respectively. The data were gathered, organized, and analyzed using statistical methods. The flexural strength findings showed a significant difference between the two groups. Also, there was a considerable decrease in the average value of the acrylic group as the concentrations of AgNPs rose, while the flexural strength of the thermoplastic group notably improved. Regarding microhardness, the results showed a significant difference between the two groups. It showed that the mean value of both groups increased with increasing concentrations of AgNPs. Within the limitations of laboratory testing conditions of this study, it was discovered that AgNPs negatively impact the flexural strength of acrylic resins. Furthermore, an increase in the concentration of AgNPs was found to be directly related to the flexural strength of thermoplastic resin and the microhardness of both groups. The concentration of AgNPs has a significant impact on certain mechanical properties of denture base materials, but it is important to consider their potential toxicity. How to cite this article: El-Hussein IG. Effect of Adding Different Concentrations of Silver Nanoparticles on Flexural Strength and Microhardness of Different Denture Base Materials. J Contemp Dent Pract 2024;25(5):417-423.

Can pulsed laser treatment reduce microbial adhesion on the surface of resin denture base materials?

Objectives. The present work investigates the influence of pulsed nanosecond laser patterning of two commercial heat cure poly (methyl methacrylate) denture base materials, Trevalon and DPI heat cure, on their surface characteristics such as roughness, hydrophobicity, and microbial adhesion. Methods. A Q-switched Nd:YAG solid state nanosecond pulsed laser at a wavelength of 532 nm with a fluence of 2.55 × 1010 W cm−2 having a pulse frequency of 10 Hz was used at varying translation stage speed and vertical spacing for the surface patterning of denture base materials. The surface properties of control and patterned materials were characterized by measuring the compositional changes, wettability, and roughness. Microbial adhesion was assessed by incubating the specimens in Candida albicans suspension at 37 °C for 2 h followed by estimating the number of adherent Candida cells. Results. The micro-Raman spectroscopic studies indicated no chemical changes in the materials due to laser patterning. However, laser patterning increased the average surface roughness from 0.02 ± 0.005 and 0.04 ± 0.003 μm to 3.85 ± 0.20 μm and 3.70 ± 0.12 μm respectively for Trevalon and DPI heat cure materials. In addition, a reduction in the surface wettability was evident as manifested by an increase in water contact angle from 76 ± 2° to 105 ± 1° for Trevalon and from 72 ± 1° to 97 ± 1° for DPI heat cure. Finally, the microbial adhesion studies clearly indicated that the surfaces with higher hydrophobicity and roughness following laser patterning exhibited reduced microbial adhesion. Significance. Laser patterning can be utilized to tune the surface features of denture base materials and thus offer a promising method to create microbial adhesion resistant surfaces. Clinically, such surfaces help in reducing the incidence of denture stomatitis, especially in immunocompromised patients, without altering the composition and bulk properties of denture base materials.

Flexural strength of repaired denture base materials manufactured for the CAD-CAM technique.

To evaluate the flexural properties of repaired poly(methylmethacrylate) (PMMA) denture base materials for computer-aided design/computer-aided manufacturing (CAD-CAM) and to compare them with heat-activated polymerized PMMA. A total of 288 specimens (65 × 10 × 2.5 mm) were prepared using both CAD-CAM and conventional blocks and repaired using autopolymerizing and visible-light polymerizing (VLC) materials. Microwave energy, water storage and hydroflask polymerization were applied as additional post-polymerization cycles after the repair process. The flexural strength (FS) of the specimens was evaluated using the three-point bending test. Data were evaluated statistically using 2-way ANOVA followed by Bonferroni's correction to determine the significance of differences between the groups (P ≤ 0.05). The FS of the denture base materials for CAD-CAM was significantly higher than that for the heat-activated group (P ≤ 0.05). The FS was significantly highest when microwave energy was used for the post-polymerization cycle. The FS values for all groups repaired with VLC resin were significantly lower than for the autopolymerization group (P ≤ 0.05). The flexural properties of denture base materials for CAD-CAM repaired using autopolymerizing acrylic resins can recover by 50-70%. Additional post-polymerization cycles for autopolymerizing repair resin can be suggested to improve the clinical service properties of repaired dentures.

Effect of denture cleansers on color stability and surface properties of denture base material containing titanium dioxide nanoparticles.

To investigate the effect of different denture cleansers on color stability, surface roughness, and hardness of polymethylmethacrylate (PMMA) infused with titanium dioxide nanoparticles (TiO2 NPs) at concentrations of 1% and 2% by weight on each. In this in vitro study, 90 disc-shaped specimens (10×10×2mm) were divided into 3 main groups: the non-containing nanoparticle group (0wt% concentration), 1wt% concentration, and 2wt% concentration TiO2 NPs groups. Each group was further assorted into 3 subgroups (n = 10): immersed in distilled water, oxygenating tablet (Corega), and 0.5% sodium hypochlorite. Color change, surface roughness, and hardness values were assessed after 90 and 180 days of storage. Color changes (∆E) were measured with a spectrophotometer (VITA, Easy Shade V, Germany) and assessed using the CIE L*a*b* colorimetric system and the American National Bureau of Standards (NBS = 0.92×∆E). The surface roughness and surface hardness values were measured using a profilometer device and Vickers hardness tester, respectively. First, ANOVA-repeated measurements were performed, followed by the Tukey test. The significance level in this study was considered 0.05. At all concentrations, there were significant differences in the mean color changes of samples immersed in cleansers compared to distilled water (p < 0.01). Moreover, hypochlorite caused a significant increase compared to Corega at 0wt% concentration after 90 days and at 1wt% concentration after 90 and 180 days. Evaluations also showed that the mean NBS values in all cleanser groups were in the range of appreciable change, except the water group. In addition, only hypochlorite changed the color higher than the clinically acceptable range (∆E >3.7). The mean roughness of samples immersed in hypochlorite at 0wt% concentration was significantly higher than the samples containing TiO2 NPs (p = 0.006). No significant difference was observed in surface roughness of samples containing different concentrations of TiO2 NPs immersed in different cleansers; however, hypochlorite increased the surface roughness of samples without TiO2 NPs compared to samples containing TiO2 NPs after 180 days. The immersion time in cleansers had a significant influence on the surface roughness and hardness while having no effect on the color. In general, the cleansers had a significant effect on color change in all groups compared to distilled water. The adverse effect of hypochlorite was more than Corega. The cleansers in the samples containing TiO2 NPs did not make a significant difference in surface roughness in comparison with the distilled water groups. Surface hardness of the samples was not affected in a steady pattern by the cleansers.

Assessment The Mechanical and Color Changes Properties of Denture Base Material After Reinforcement with Nanoparticles Material

Although PMMA is widely used in prosthetic dentistry, but broken dentures are commonly known clinical events that remain as unsolved problems. The aim of this study was to evaluate the effect of incorporation Magnesium oxides nanoparticles with different concentrations on hardness and color changes o f heat cure acrylic resin. A total of 40-disc shape specimens with a diameter of (12±0.1) mm and a thickness of (2±0.1) mm were prepared from heat cure acrylic resin. They were grouped into 4 groups according to nanoparticles concentrations (10) specimens for each group, then they are subjected to hardness and color changes tests. Control group (A): (10 specimens) without addition. Group (B): 10 specimens of acrylic resin with (2%) concentration of MgO. Group (C): 10 specimens of acrylic resin with (4%) concentration of MgO. Group (D): 10 specimens of acrylic resin with (6%) concentration of MgO. The results showed there is high significant difference for MgO (2%, 4%) when compared with the controls. While there is no significant variation for MgO (6%). color changes showed there is a non-significant difference for all groups except for (6%) group which revealed there is high significant difference. Adding limited concentration of MgO (2%, 4%) have a positive effect on hardness of surfaces and color changes of heat-cured acrylic resins. any Increase in Concentration of MgO will effect adversely on hardness of surfaces and color stabiliti

Comparative Evaluation of Flexural and Impact Strength of Denture Base Acrylic Resin using Different Processing Methods - An in-vitro Study

Background: One of the chief limitations of Polymethylmethacrylate denture base material is its inadequate mechanical property. Different processing methods of Polymethylmethacrylate have varying influences on the mechanical properties of denture base material. Aim: The aim of our in-vitro study was to comparatively evaluate the flexural and impact strength values between CAD-CAM, Compression-molded and Injection- molded Polymethylmethacrylate specimens. Materials and methods: A total of 66 acrylic rectangular specimens of ISO Standardization (64 x10 x3.3mm) were fabricated. This study was conducted between three groups: Group I (n=22)-CAD-CAM Milled specimens (Ruthinium, India), Group II (n=22)- Compression-molded specimens (Dental Products of India, Chennai), Group III (n=22)- Injection-molded specimens (SR- Ivocap High Impact, Ivoclar Vivadent). Flexural strength was evaluated using four-point bend test and Impact strength by IZOD Impact tester. Kruskal Wallis unpaired test was used to compare the mean values between groups and Mann Whitney U test was used to carry out pair wise comparison. Results: Flexural strength of CAD-CAM samples were found to be statistically highest followed by injection molded specimens. Conversely, Impact strength of injection- molded specimens were highest followed by CAD-CAM specimens. Flexural as well as impact strength values were found to be least among compression-molded specimens. Conclusion: CAD-CAM specimens exhibited higher flexural strength whereas Injection-molded specimens had the highest impact strength.

Enhancement of PMMA base Denture Material: A Review

As we know Teeth problems can be prominent as age increases also due to accident teeth breaks. Physical appearance can be greatly affected by teeth. So we need to test material which has better or similar properties to the natural teeth before restoring teeth with suitable material. Therefore, it is important to study the physical and mechanical properties of denture base material. Denture base material properties can be improved by adding various monomers and cross linking agent. Focus is on the increase of impact strength other mechanical properties of denture material. Different additives being used should be compatible with MMA (Methyl methacrylate) and polymerize to PMMA (Poly methyl methacrylate). Heat cure and variation in chemical composition can affect the mechanical properties. This paper presents the review of the work that has been done to improve the properties of denture base material and the problems being faced during the fabrication. The gap in the literatures available has been also discussed.

Influence of ZrO2 Nanoparticle Addition on the Optical Properties of Denture Base Materials Fabricated Using Additive Technologies

This study investigated the translucency of 3D-printed denture base resins modified with zirconium dioxide nanoparticles (ZrO2NPs) under thermal cycling. A total of 110 specimens were fabricated and divided into 3 groups according to the materials, i.e., heat-polymerized resin, and 3D-printed resins (NextDent, and ASIGA). The 3D-printed resins were modified with 0, 0.5, 1, 3, and 5 wt.% of ZrO2NPs. All the specimens were subjected to 5000 thermal cycles. The translucency was measured using a spectrophotometer. The results showed that the heat-polymerized resin had considerably higher translucency than the 3D-printed resins. Compared to the unmodified group, the translucency decreased significantly after adding 5% ZrO2NPs to NextDent and 3% ZrO2NPs to ASIGA resins. The highest translucency was achieved for NextDent by adding 0.5% ZrO2NPs and for ASIGA without any ZrO2NPs. It was found that the average concentration level in ASIGA was significantly higher than that in NextDent. These findings revealed that 3D-printed resins have lower translucency than heat-polymerized acrylic resin, and adding ZrO2NPs at low concentrations did not affect the translucency of the 3D-printed resins. Therefore, in terms of translucency, 3D-printed nanocomposite denture base resins could be considered for clinical applications when ZrO2NPs are added at low concentrations.

Effect of Gum Arabic powder on the mechanical properties of denture base acrylic.

This study aimed to improve the mechanical properties of denture base material using various concentrations of natural biopolymer, i.e., Gum Arabic (GA). This experimental study was conducted at the Dental Health Department of the College of Applied Medical Sciences, King Saud University, Riyadh, Saudi Arabia from May 2022 to July 2022. After obtaining exemption from the institutional review board, the powdered GA was added in ratios of weight 5, 10, and 20% to PMMA heat-cured acrylic powder to produce bar-shaped samples (65 × 10 × 30 mm3 in dimensions). While the control group was prepared as such. Micro hardness (n=10/group) and fracture toughness (n=10/group) were evaluated. One-way analysis of variance method was used to statistically analyze the results (p<0.05) using SPSS version 23. Significant differences were observed for micro hardness (p<0.001) and fracture toughness (p=0.007) between the means of the different study groups. The control group exhibited the highest micro hardness (22.5±0.6 VHN) and fracture toughness (1.25±0.11 MPa.m1/2) value among the study groups. While 20 wt. % GA and 10 wt. % GA groups showed the lowest micro hardness and fracture toughness values, respectively. GA powder might not be an appropriate reinforcing material for denture base or the higher filler loading of GA in denture base acrylic might be detrimental to the mechanical properties.

Effect of Natural Fibers on Some Thermal and Physical Properties of Denture Base Materials

In this research, composite material consist of PMMA and MMA as a matrix materials was prepared and reinforced by natural fibers (sisal fibers) in different concentrations (5, 10%wt). The conventional processing technique for complete dentures was followed to prepare the composite specimens. FTIR test was carried out to reinforcement material (sisal fibers) before and after salinization to determine, whether or not there is chemical bond between reinforcements materials and saline coupling agent. Physical tests such as thermal conductivity, water sorption and solubility were performed on all specimens. The results refer to a highly significant differences in: thermal conductivity, water sorption and solubility of reinforced specimens compared with pure specimens. Increasing the fiber concentration showed a slight decrease in the thermal conductivity of PMMA specimens reinforced with sisal fibers, and increase both water sorption and solubility of composite specimens. FTIR results showed a new absorption band was developed after sialne treatment.

Effects of long-term cinnamaldehyde immersion on the surface roughness and color of heat-polymerized denture base resin

Statement of problemCinnamaldehyde has been successfully used for the short-term disinfection of dentures; however, its long-term effects on the surface and color properties of denture base materials remain unknown. PurposeThe purpose of this in vitro study was to evaluate the effects of simulated immersion in cinnamaldehyde for up to 5 years on the surface roughness and color parameters of a heat-polymerized denture resin. Material and methodsEighty Ø10×5-mm disk-shaped specimens were prepared from microwave heat-polymerized polymethylmethacrylate (PMMA) and immersed in 4 solutions (n=20): TW–tap water (control), SH – 0.5% sodium hypochlorite, PX–alkaline peroxide, and CA–cinnamaldehyde (27 μg/mL). The immersion protocol simulated 104 cycles (3.5 months), 913 cycles (2.5 years), and 1825 immersion cycles (5 years) of a daily immersion cleaning protocol, with immersion times ranging from 10 to 20-minutes. Surface roughness (Sa) and the color parameters of CIELab (L∗ a∗ b∗, ΔEab), CIEDE2000 (ΔE00), and the National Bureau of Standards (NBS) were analyzed at baseline (t=0) and after the immersion cycles. The data were analyzed by 2-way analysis of variance (ANOVA) for repeated measures and the Tukey post hoc test (α=.01). ResultsSa was significantly increased in all groups after 1825 cycles compared with baseline (P<.01), regardless of the solution. Only the time factor significantly affected ΔEab, ΔE00, and NBS parameters, which were below the perceptibility and acceptability thresholds. After a simulated 5-year immersion, the surface roughness and color values of CA-treated specimens were not statistically different from those of the other groups (P>.01). ConclusionsCinnamaldehyde solution (27 μg/mL) produced minor effects on the surface roughness and color parameters of a heat-polymerized denture base resin similar to those of 0.5% sodium hypochlorite and alkaline peroxide after a 5-year simulated immersion.

Mechanical Properties of the Modified Denture Base Materials and Polymerization Methods: A Systematic Review.

Amidst growing technological advancements, newer denture base materials and polymerization methods have been introduced. During fabrication, certain mechanical properties are vital for the clinical longevity of the denture base. This systematic review aimed to explore the effect of newer denture base materials and/or polymerization methods on the mechanical properties of the denture base. An electronic database search of English peer-reviewed published papers was conducted using related keywords from 1 January 2011, up until 31 December 2021. This systematic review was based on guidelines proposed by the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA). The search identified 579 papers. However, the inclusion criteria recognized 22 papers for eligibility. The risk of bias was moderate in all studies except in two where it was observed as low. Heat cure polymethyl methacrylate (PMMA) and compression moulding using a water bath is still a widely used base material and polymerization technique, respectively. However, chemically modified PMMA using monomers, oligomers, copolymers and cross-linking agents may have a promising result. Although chemically modified PMMA resin might enhance the mechanical properties of denture base material, no clear inferences can be drawn about the superiority of any polymerization method other than the conventional compression moulding technique.

A comparative evaluation of properties of denture base materials processed with different processing methods: a preliminary study

A comparative evaluation of properties of denture base materials processed with different processing methods: a preliminary study

Biological and Mechanical Properties of Denture Base Material as a Vehicle for Novel Hydroxyapatite Nanoparticles Loaded with Drug.

Purpose: This study aimed to evaluate the biological and mechanical properties of the poly(methyl methacrylate) (PMMA) denture base material as a vehicle incorporating novel hydroxyapatite nanoparticles (HA-NP) loaded with metronidazole (MZ) drug. Methods: HA-NP was prepared via wet-chemical-method, characterized by XRD, SEM/EDX, TEM, Fourier-transform infrared spectroscopy (FTIR), as well as the measurement of surface area and pore-size distribution. Four drug delivery formulas were prepared in the form of discs (10 x 2 mm) as follows: F1 (MZ/ HA-NP/PMMA), F2 (HA-NP/ PMMA), F3 (control-PMMA) and F4 (MZ/PMMA). Characterization of all formulas was performed using differential scanning calorimetry (DSC) and FTIR. MZ release rate, antimicrobial properties against three oral pathogens, cytotoxicity (MTT assay) and surface micro-hardness were also assessed. Statistical analysis of data was performed using one-way ANOVA test (P < 0.05). Results: DSC thermograms showed compatibility among MZ, HA-NP and PMMA along with physical stability over 6 months storage period at room temperature. FTIR spectroscopy proved the absence of any possible chemical interaction with MZ. MZ-HA-NP/PMMA formula showed relatively better drug release compared to MZ-PMMA. Both formulas showed statistically significant antimicrobial potentials against two microbial strains. MTT demonstrated reduction in cell cytotoxicity after 96 hours with the least value for HA-NP. Surface micro-hardness revealed non-significant reduction compared with the control PMMA. Conclusion: A novel biocompatible drug nanocarrier (HA-NP) was developed and incorporated in PMMA denture base material as a vehicle to allow prolonged sustained drug release to manage oral infections.

Synthesis, characterization of Ag+ and Sn2+ complexes and their applications to improve the biological and mechanical properties of denture base materials

A new Ag+ and Sn2+ complexes of polymethyl methacrylate amide sulfadiazine (ligand H2L) were synthesized. The synthesized compounds were characterized by elemental analysis, TGA, SEM, TEM and spectral studies including 1H NMR, 13C NMR, FTIR, Electronic absorption and X-ray powder diffraction. The analytical and spectral technique used has identified that the H2L ligand acts as bidentate by amide group atoms of oxygen and nitrogen. For Ag+ and Sn2+ complexes the stoichiometry is 1:1 and 1:2 (M: Ligand) respectively. The results confirm the tetrahedral geometry of the Ag+ complex and an octahedral structure of the Sn2+ complex. The spectra of X-ray powder diffraction and TEM data show the nano-scale synthesized compounds. The antifungal activity of the synthesized ligand and its Ag+ and Sn2+ complexes was tested in vitro against the fungal Candida albicans before and after addition to the heat-polymerized acrylic denture base resin material. The data showed strong antifungal activity in the Sn2+ complex than in Ag+ complex and H2L ligand. Before and after combination with complexes H2L, Ag+, and Sn2+, the mechanical properties of acrylic denture base resin were studied. The results showed that the flexural strength, modulus, and hardness of acrylic denture base resin have improved than the control group. The addition of Sn2+ complex has decreased the deflection of acrylic resin more than H2L, while it has increased with the addition of Ag+ complex. Roughness decreased in heat-polymerized acrylic resin after adding H2L, Ag+, and Sn2+ complexes.

The effect of different cooling procedures on mechanical properties of denture base materials measured by instrumented indentation testing

PurposeTo evaluate the different cooling procedures on the mechanical properties of five heat-cured polymethyl methacrylate (PMMA) denture materials. Methods250 specimens were made equally from Meliodent (ME), Paladon 65 (PA), Probase Hot (PB), Stellon QC–20 (QC) and Vertex Rapid Simplified (VE) implementing five different cooling procedures (n=10/procedure): A) removal from water bath, bench-cooling (10min) and cooling under water (15min), B) remain in water bath till room temperature, C) removal from water bath and cooling in water for 15min, D) removal from water bath and bench cooling till room temperature and E) removal from water bath, bench cooling for 30min and cooling under water for 15min. The specimens were immersed in distilled water (15 days/37ºC) and then subjected to Instrumented Indentation Testing for Martens Hardness (HM), indentation modulus (EIT) and elastic index (ηΙΤ). Results were statistically analyzed by two- and one-way Analysis of variance (ANOVA) plus Tukey post hoc tests (α=0.05). ResultsThe highest values for HM were recorded for QC, PA, VE with B cooling procedure, PB with A and ME with E, for EΙΤ for QC, PB with A, for PA, VE with B and ME with E, and for ηIT for QC, PB with B, PB with E, ME with C and VE with D. ConclusionsThe cooling procedures recommended for PB resulted in the lowest mechanical properties. A and B may be considered as universal short- and long-cooling procedures respectively providing the highest mechanical properties for the materials tested.

The effect of polyamide microparticles addition on some mechanical prop-erties of light-cured acrylic resin

The general upgrading of polymer denture base material and research continuously looking for ideal restorative dental material with better properties, adequate esthetic properties, less expensive and easier to handle material to develop photo polymerization dental materials. This study was conducted to evaluate the effect of addition polyamide on mechanical microparticle properties light cure denture base material. One hindered sixty specimens from light-cured acrylic resin (Aurora). The divided mainly into four groups according to test used (Transverse strength test, impact strength test, hardness test and tensile strength test) with 40 specimens for each group. The results show an increase in Transverse strength, impact strength, hardness and tensile strength in all experimental group when compared to control group the highest mean values for all tests included in the study appeared in group B 1% polyamide. The addition of polyamide microparticle improves transverse, tensile, impact strength and hardness properties of denture base material.

Studying the Mechanical Properties of Denture Base Materials Fabricated from Polymer Composite Materials

Studying the Mechanical Properties of Denture Base Materials Fabricated from Polymer Composite Materials