Adhesive Properties Research Articles

Bioinspired poly-dopamine/nano-hydroxyapatite: an upgrading biocompatible coat for 3D-printed polylactic acid scaffold for bone regeneration.

Poly-lactic acid (PLA) has been proposed in dentistry for several regenerative procedures owing to its biocompatibility and biodegradability. However, the presence of methyl groups renders PLA hydrophobic, making the surface less ideal for cell attachment, and it does not promote tissue regeneration. Upgrading PLA with inductive biomaterial is a crucial step to increase the bioactivity of the PLA and allow cellular adhesion. Our purpose is to evaluate biocompatibility, bioactivity, cellular adhesion, and mechanical properties of 3D-printed PLA scaffold coated with poly-dopamine (PDA) and nano-hydroxyapatite (n-HA) versus PLA and PLA/n-HA scaffolds. The fused deposition modelling technique was used to print PLA, PLA with embedded n-HA particles, and PLA scaffold coated with PDA/n-HA by immersion. After matrices characterization for their chemical composition and surface properties, testing the compressive strength was pursued using a universal testing machine. The bioactivity of scaffolds was evaluated by monitoring the formation of calcium phosphate compounds after simulated body fluid immersion. The PLA/PDA/n-HA scaffold showed the highest compressive strength which was 29.11 ± 7.58 MPa with enhancing calcium phosphate crystals deposition with a specific calcium polyphosphate phase formed exclusively on PLA/PDA/n-HA. With cell viability assay, the PDA/n-HA-coated matrix was biocompatible with increase in the IC50, reaching ⁓176.8 at 72 without cytotoxic effect on the mesenchymal stem cells, promoting their adhesion and proliferation evaluated by confocal microscopy. The study explored the biocompatibility, bioactivity, and the cell adhesion ability of PDA/n-HA coat on a 3D-printed PLA scaffold that qualifies its use as a promising regenerative material.

Tissue hydrate layer-trigger swollen gelatin-based aerogel hemostatic material with bletilla striata complex active ingredient complex to promote hemostasis

Gelatin exhibits excellent solubility at the 37℃ tissue surface due to its affinity for the rich tissue hydrate water. However, its inherent property doesn't facilitate the formation of a robust physical barrier to effectively manage wound hemorrhage and promote hemostasis. To address this challenge, a novel gelatin-based derivative (Ged) with swollen property upon absorbing the tissue hydrate layer was prepared. In this work, a hydrophobic monomer was introduced into gelatin under amide reaction to regulate the interactions between water molecules and gelatin molecular chains. This investigation results showed that Ged exhibited excellent adhesion properties and long-term swollen at 37 °C. In addition, bletilla striata complex active ingredients (Bscai) was employed to the Ged to promote hemostasis capacity, which referred to as Bscai/Ged hemostatic material. In-depth experiments were conducted to investigate the structural characteristics and biocompatibility of Bscai/Ged hemostatic materials, those results revealed that Bscai/Ged hemostatic materials had swift hydrate layer-trigger rate, robust adhesive strength on wet tissue surfaces, outstanding hemostatic properties and facilitating accelerated wound healing. Additionally, in vivo experimental results indicated that the Bscai/Ged hemostatic material could mitigate inflammatory responses, promote collagen deposition and enhance angiogenesis. Overall, Bscai/Ged hemostatic material presents a highly promising candidate for advanced hemostatic material applications.

Regulation of the Properties of Polymers based on Thiirane using Mixtures of Amine Hardeners

Abstract: Introduction: The possibility of regulating the curing rate and the complex of adhesive, deformation-strength and dynamic mechanical properties of polymers based on bisphenol A dithioester (thiirane) using a mixture of amine hardeners of various chemical nature is investigated. Method: Diethylenetriamine, diethylenetriaminomethylphenol and aminopolyamide were investigated as hardeners. The ratio of the components of the mixed hardener is selected, which provides the best combination of strength properties. Results: It was found that the rate of adhesion and cohesive strength at the initial stage (during the first hour) of curing compositions containing a mixture hardener significantly exceeds compositions cured by individual components of the mixture. Conclusion: The results of measuring the dynamic mechanical characteristics of the studied polymers indicate that the dynamic modulus of elasticity, measured at temperatures below and above the transition from a glassy state to a high elastic one, for a sample containing a mixed hardener has an intermediate value between the values characteristic of samples containing individual components of a mixed hardener. objective: The ratio of the components of the mixed hardener is selected, which provides the best combination of strength properties.

Regulatable Orthotropic 3D Hybrid Continuous Carbon Networks for Efficient Bi-Directional Thermal Conduction

HighlightsA composite thermal interface material with three-dimensional hybrid carbon network-reinforced polydimethylsiloxane was proposed.The cooperative regulation of thermal conductivity and mechanical properties was achieved by controlling the assembly process of micro-nano scale unit carbon materials.The orthotropic continuous carbon structure endowed the composites with in-plane and out-of-plane thermal conductivities of up to 113.61 and 24.37 W m−1 K−1, respectively.The excellent compressibility and adhesion properties cooperatively improved the effective thermal conductivity by more than an order of magnitude.

Effect of folA gene in human breast milk-derived Limosilactobacillus reuteri on its folate biosynthesis

IntroductionFolate supplementation is crucial for the human body, and the chemically synthesized folic acid might have undesirable side effects. The use of molecular breeding methods to modify the genes related to the biosynthesis of folate by probiotics to increase folate production is currently a focus of research.MethodsIn this study, the folate-producing strain of Limosilactobacillus reuteri B1-28 was isolated from human breast milk, and the difference between B1-28 and folA gene deletion strain ΔFolA was investigated by phenotyping, in vitro probiotic evaluation, metabolism and transcriptome analysis.ResultsThe results showed that the folate producted by the ΔFolA was 2–3 folds that of the B1-28. Scanning electron microscope showed that ΔFolA had rougher surface, and the acid-producing capacity (p = 0.0008) and adhesion properties (p = 0.0096) were significantly enhanced than B1-28. Transcriptomic analysis revealed that differentially expressed genes were mainly involved in three pathways, among which the biosynthesis of ribosome and aminoacyl-tRNA occurred in the key metabolic pathways. Metabolomics analysis showed that folA affected 5 metabolic pathways, involving 89 different metabolites.DiscussionIn conclusion, the editing of a key gene of folA in folate biosynthesis pathway provides a feasible pathway to improve folate biosynthesis in breast milk-derived probiotics.

Coal gangue in asphalt pavement: A review of applications and performance influence

The comprehensive utilization of coal gangue is low, and this causes serious environment problems and security risks. The physical and chemical properties of coal gangue were analyzed in this paper, and the estimated value of different chemical components of coal gangue was counted. The physical properties of coal gangue aggregate were analyzed, and performance and its influencing factors of base course mixture with coal gangue aggregate were studied. The influence of coal gangue powder and coal gangue aggregate on performance of asphalt mortar and asphalt mixture was analyzed, and possible influencing factors and function mechanism were discussed. The results showed that heavy metal elements of coal gangue applied into asphalt pavement is not seeped out. The crushing value, water absorption and flat elongated particles content of coal gangue aggregate are generally high, but the compressive strength of base course with coal gangue aggregate is verified to meet the strength requirement. The performance, volume stability and durability of base course with coal gangue aggregate are closely related to aggregate gradation, the type and dosage of cementations materials and aggregate. The high temperature performance, temperature susceptibility and viscosity of asphalt mortar are improved by the addition of different coal gangue powder, and improvement effect of activated coal gangue powder on asphalt mortar performance is better. The low temperature performance and adhesion property of asphalt mortar with chemical activated coal gangue powder are improved. The physical reaction between asphalt and different coal gangue powder is only taken place. The temperature stability of asphalt mixture with coal gangue coarse aggregate has achieved the specification requirement. The water stability and low temperature fracture performance of asphalt mixture with fine aggregate replaced by coal gangue are improved. However, the high temperature performance of above mixture is lower than conventional hot mix asphalt mixture. The research results will provide reference for coal gangue applied into asphalt pavement.

Long-term performance of chemically modified cotton straw fibers in micro-surfacing asphalt mixtures

Using agricultural wastes in asphalt pavements presents a promising solution to enhance pavement performance and utilize agricultural wastes simultaneously. In the paper, the fibers are made from recycled cotton stalks. Chemical modifiers are chosen to enhance the adherence of fiber asphalt binders. Different modified fibers are added to the SBR-modified emulsified asphalt. The modified asphalt binders are then utilized to prepare asphalt mixtures. Comparative studies on construction performance, road performance, and durability were carried out. Results showed that water consumption and bitumen aggregate ratio at the micro-surfacing were increased after adding fiber. Fibers with low hygroscopicity, rough surface, and high asphalt absorption rate had better adhesion properties. The long-term performance of a micro-surfacing mixture was most remarkably improved by the CH3COOH-modified cotton straw fibers, demonstrating a 10.07% drop in rutting depth, a 9.13% decrease in abrasion value, and a 41.13% gain in shear resistance compared to the micro-surfacing mixtures with unmodified fibers. The study concluded that modified fiber micro-surfacing asphalt mixes are more suitable for seasonal frozen regions than the conventional mixes. The findings offer a theory foundation for the future development of cotton straw fibers in road engineering.

Biodegradable polylactic acid emulsion ink based on carbon nanotubes and silver for printed pressure sensors

Investigating biodegradable and biocompatible materials for electronic applications can lead to tangible outcomes such as developing green-electronic devices and reducing the amount of e-waste. The proposed emulsion-based conducting ink formulation takes into consideration circular economy and green principles throughout the entire process, from the selection of materials to the production process. The ink is formulated using the biopolymer polylactic acid dissolved in a sustainable solvent mixed with water, along with conductive carbon nanotubes (CNTs) and silver flakes as fillers. Hybrid conductive fillers can lower the percolation threshold of the ink and the production costs, while maintaining excellent electrical properties. The coating formed after the deposition of the ink, undergoes isothermal treatment at different temperatures and durations to improve its adhesion and electrical properties. The coating’s performance was evaluated by creating an eight-finger interdigitated sensor using a Voltera PCB printer. The sensor demonstrates exceptional performance when exposed to various loading and unloading pressures within the 0.2–500.0 kPa range. The results show a consistent correlation between the change in electrical resistance and the stress caused by the applied load. The ink is biodegradable in marine environments, which helps avoiding its accumulation in the ecosystem over time.

Dental biomaterials redefined: molecular docking and dynamics-driven dental resin composite optimization

BackgroundDental resin-based composites are widely recognized for their aesthetic appeal and adhesive properties, which make them integral to modern restorative dentistry. Despite their advantages, adhesion and biomechanical performance challenges persist, necessitating innovative strategies for improvement. This study addressed the challenges associated with adhesion and biomechanical properties in dental resin-based composites by employing molecular docking and dynamics simulation.MethodsMolecular docking assesses the binding energies and provides valuable insights into the interactions between monomers, fillers, and coupling agents. This investigation prioritizes SiO2 and TRIS, considering their consistent influence. Molecular dynamics simulations, executed with the Forcite module and COMPASS II force field, extend the analysis to the mechanical properties of dental composite complexes. The simulations encompassed energy minimization, controlled NVT and NPT ensemble simulations, and equilibration stages. Notably, the molecular dynamics simulations spanned a duration of 50 ns.ResultsSiO2 and TRIS consistently emerged as influential components, showcasing their versatility in promoting solid interactions. A correlation matrix underscores the significant roles of van der Waals and desolvation energies in determining the overall binding energy. Molecular dynamics simulations provide in-depth insights into the mechanical properties of dental composite complexes. HEMA-SiO2-TRIS excelled in stiffness, BisGMA-SiO2-TRIS prevailed in terms of flexural strength, and EBPADMA-SiO2-TRIS offered a balanced combination of mechanical properties.ConclusionThese findings provide valuable insights into optimizing dental composites tailored to diverse clinical requirements. While EBPADMA-SiO2-TRIS demonstrates distinct strengths, this study emphasizes the need for further research. Future investigations should validate the computational findings experimentally and assess the material's response to dynamic environmental factors.

Harnessing Green Electricity from Food: A Split Black Gram-Based Triboelectric Nanogenerator for a Self-Powered Autonomous Lighting System and Portable Electronics.

Triboelectric nanogenerators (TENGs) represent a promising solution to mounting environmental concerns associated with battery disposal amid the escalating demand for portable electronics. However, prevailing TENG fabrication predominantly relies on nonbiodegradable, nonbiocompatible, and synthetic materials, posing a grave ecological threat. To mitigate this, there is a pressing need to develop eco-friendly and green TENGs leveraging sustainable, naturally occurring materials. This study pioneers the use of split black gram (SBG) as a tribo-positive material for TENGs. SBG's effectiveness as a tribo-positive material stems from its abundance of oxygen-containing functional groups, as confirmed by FTIR analysis, facilitating electron donation during the triboelectric process. SBG offers compelling advantages, including widespread availability, cost-effectiveness, biodegradability, and hydrophobic and adhesive properties due to its richness in starch and protein, positioning it as an optimal choice for eco-conscious TENG manufacturing. The fabrication process of an SBG-TENG is not only economical and facile but also solvent-free, requiring no specialized tools. Demonstrating commendable performance, the SBG-TENG achieves a maximum power density of 15.36 μW/cm2 at 1 MΩ, with an open circuit voltage of 84 V and short circuit current of 28 μA, comparable to recent studies. In practical applications, the SBG-TENG seamlessly integrates with LEDs and portable electronic devices via a full bridge rectifier, successfully powering them postcapacitor charging. Moreover, an autonomous lighting system is developed by embedding the SBG-TENG in a foot mat, enabling wireless light control through human stepping on the mat, introducing power-saving functionality for residential and office environments. In essence, the introduction of the SBG-TENG not only delivers cost-effectiveness but also minimizes the environmental impact by harnessing sustainable energy from food sources.

Comparison and investigation of H-bond assisted reusable PU adhesives with high shear strength

Hot-melt adhesive (HMA) is commonly used in industrial manufacturing due to its ease of use. However, the direct factors that affect shear strength have been unclear in recent years, making it difficult to prepare hot melt adhesives with high shear strength, which are mostly lower than 6 MPa. In this study, three types of polyurethane HMAs, differing in the position of H-bond motifs, ureidopyrimidinone (UPy), were synthesized and characterized, the most central factor for shear strength, Young's modulus, was firstly found out and proved. Side-chain UPy provides better flexibility and more chain entanglement. The lap shear strength of SPU was about 13.48 MPa, which was the highest shear strength of PU HMA, and remained 73.4 % even after 4 cycles. Compared to the other two samples, the side-chain motifs improved the possibility of forming hydrogen bonds with adherends and increased chain mobility. This led to a more efficient wetting process and strengthened Young's modulus directly, enhancing adhesive property incomparably. This work provides a satisfactory method for achieving high shear strength in HMA.

Slate–Cork Laminate Enhanced with Silicone for Habitat Industry Application

This study investigates the feasibility of using a composite material comprising slate reinforced with cork sheets for architectural purposes like facades and wall coverings. The research involves the comprehensive characterisation of both slate and cork materials along with the evaluation of the silicone adhesive used in their bonding process, specifically Sikasil® HT from SIKA®. It was found that both slate and cork exhibited low wettability, which was enhanced through cold plasma treatment. Subsequently, a composite sandwich structure was fabricated and subjected to impact testing in a drop tower, along with fire resistance evaluations. The fire tests revealed that when subjected to a flame of 900 °C for 15 min, the slate alone heated rapidly, reaching 500 °C within 3 min on the side opposite to the flame. However, the sandwich structure reached 260 °C on the cork side (opposite to the flame) at 7.5 min, maintaining this temperature until the deterioration or detachment of the cork between 11 and 12 min. This provided insulation and delayed ignition. The sandwich structure maintained its fire resistance due to the insulating properties of cork and the superior thermal resistance of silicone compared to other adhesives up to 260 °C. Overall, the results suggest the potential suitability of this sandwich structure for architectural applications. Its favourable adhesion properties and acceptable fire resistance indicate that it could serve as a viable alternative for construction materials in architectural contexts.

Defined Transfer of Colloidal Particles by Electrochemical Microcontact Printing

AbstractSoft lithography, in particular microcontact printing (µCP), represents a well‐established and widespread class of lithographic patterning techniques. It is based on a directed deposition of molecules or colloidal particles by a transfer process with a micro‐structured stamp. A critical aspect of µCP is the adhesion cascade that enables the directed transfer of the objects. Here, the interfacial properties of a µCP‐stamp are tuned electrochemically to modify the adhesion cascade. During the printing process, the µCP‐stamp is submerged in an electrolyte solution and acted as a working electrode whose surface properties depended on the externally applied potential, thus enabling in situ rapid switching of its adhesion properties. As a proof of principle, defined particle patterns are selectively removed from a monolayer of colloidal particles. The adhesion at the particle/solid interface and the transfer mechanisms are determined by using the colloidal probe technique based on atomic force microscopy (AFM). In this case, a single particle is brought into contact with an electrode with the same surface chemistry as the µCP‐stamp. Hence, it became possible to determine the electrochemical potential ranges suitable to establish an adhesion cascade.

Engineering Wet-Resistant and Osteogenic Nanocomposite Adhesive to Control Bleeding and Infection after Median Sternotomy.

Median sternotomy surgery stands as one of the prevailing strategies in cardiac surgery. In this study, the cutting-edge bone adhesive is designed, inspired by the impressive adhesive properties found in mussels and sandcastle worms. This work has created an osteogenic nanocomposite coacervate adhesive by integrating a cellulose-polyphosphodopamide interpenetrating network, quaternized chitosan, and zinc, gallium-doped hydroxyapatite nanoparticles. This adhesive is characterized by robust catechol-metal coordination which effectively adheres to both hard and soft tissues with a maximum adhesive strength of 900 ± 38kPa on the sheep sternum bone, surpassing that of commercial bone adhesives. The release of zinc and gallium cations from nanocomposite adhesives and quaternized chitosan matrix imparts remarkable antibacterial properties and promotes rapid blood coagulation, in vitro and ex vivo. It is also proved that this nanocomposite adhesive exhibits significant in vitro bioactivity, stable degradability, biocompatibility, and osteogenic ability. Furthermore, the capacity of nanocomposite coacervate to adhere to bone tissue and support osteogenesis contributes to the successful healing of a sternum bone defect in a rabbit model in vivo. In summary, these nanocomposite coacervate adhesives with promising characteristics are expected to provide solutions to clinical issues faced during median sternotomy surgery.

Identification method on the vibration properties of a periodic core sandwich: Thermal impact on the band gap

This paper focuses on the thermal impact of filtering properties on sandwich structures with periodic core. The evolution of the bandgap is carefully studied as a function of temperature. Sandwich structure allows to shear the viscoelastic core layer and increases passive damping. Two polymers are selected for their viscoelastic properties and their adhesion properties with metal surfaces. The mechanical properties, shear modulus G(ω) and loss factor η(ω) of these polymers, are determined at temperature by an inverse method. The periodicity of the sandwich structure is achieved by alternating two materials with specific viscoelastic properties in the core, allowing resonant frequencies to be located in beams creating frequency ranges without resonant peaks. Temperature has a strong influence on the mechanical properties of polymer materials. This is why we felt it was important to be able to carry out a temperature investigation. Numerical finite element modelling is developed considering periodicity and temperature. Periodic sandwich fabricated in our laboratory are tested under thermal conditioned. The results show the importance of considering the effect of temperature. It has a direct impact on the filtering properties obtained by periodic structures.

Laboratory assessment of the impact of modified asphalt binder on mechanical properties of grouted macadam mixtures under various performance conditions

ABSTRACT Grouted Macadam (GM) mixtures are used for pavement coatings due to their strong load-bearing capacity and rutting resistance. However, weak asphalt-cement interface bonding reduces crack resistance performance of these mixtures. This study aimed to enhance this adhesion through implementing TEGO Addibit L300 additive at concentrations of 0.2, 0.3, and 0.4% by weight of asphalt binder. Various tests assessed additive’s impact on asphalt binder properties, including penetration, softening point, and kinematic viscosity. Adhesion properties were evaluated through sessile drop and semi-circular bending bonding strength tests. Additionally, GM mixture performance was assessed with mechanical tests such as 3-point bending strength, indirect tensile strength, and Marshall stability, considering two conditions: samples tested immediately after a 28-day curing period (non pre-conditioned samples), and samples tested after the same period followed by exposure to 60 ℃ for 16 h (pre-conditioned samples). Results revealed that the adhesion capacity of the asphalt binder significantly affected GM mixture performance in both conditions. Addition of TEGO Addibit L300 enhanced ductility and fracture energy by 53.9% and 45.2%, respectively, in non pre-conditioned samples. In pre-conditioned samples, the additive increased indirect tensile strength by up to 12.1%. The optimal dosage for improving GM materials performance was determined to be 0.3%.

Surface engineering of aerospace aluminium alloys: Understanding alloying effects on chemical pre-treatment and sol-gel coating adhesion

The sol–gel process is a chemical surface preparation method based on hydrolysis and polycondensation reactions for enhanced adhesion for metallic substrates in adhesive bonding and coating applications. This paper describes an investigation into the effect of the microstructural complexity of two commonly used aerospace aluminium alloys (AAs) 2024-T3 and 7075-T6, on the response to different surface pre-treatments before deposition of the sol-gel coating and subsequent adhesive bonding.Different surface pre-treatments, including two abrasive treatments and three chemical surface pre-treatments were used, and their effect on surface chemistry, wettability and roughness was assessed. Surfaces were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, profilometry and static contact angles. A hybrid silane sol-gel film was deposited on the differently pre-treated aluminium alloys, an epoxy adhesive was applied and the adhesion properties were evaluated using pull-off testing. The role of the altered physicochemical properties of the pre-treated surfaces was related to the adhesion strength of the sol–gel reinforced epoxy/aluminium interfaces.The microstructural complexity of the aerospace alloys caused non-uniform responses to the pre-treatments, proving the importance of compatibility between material and treatment conditions. Statistical analysis revealed that, despite that overall higher adhesion values were obtained on rougher surfaces, only a strong correlation exists between the surface hydroxyl fraction and adhesion strength. The relation of roughness and water contact angle to interfacial adhesion was found to be non-significant.The findings of this study underscore the critical role of surface pre-treatments and their impact on adhesion strength in aerospace aluminium alloys, providing valuable insights for the effective utilization of sol-gel coatings in adhesive bonding and coating processes.

Molybdesum selenide-based platelet-rich plasma containing carboxymethyl chitosan/polyvinyl pyrrolidone composite antioxidant hydrogels dressing promotes the wound healing

Excess free radicals at the wound site can cause an inflammatory response, which is not conducive to wound healing. Hydrogels with antioxidant properties can prevent inflammatory storms by scavenging free radicals from the wound site and inhibiting the release of inflammatory factors. In this study, we prepared the carboxymethyl chitosan (CMCS)/polyvinyl pyrrolidone (PVP)/Molybdenum (IV) Selenide (MoSe2), and platelet-rich plasma (PRP) (CMCS/PVP/MoSe2/PRP) hydrogels for accelerating the repair of wounds. In the hydrogels, the MoSe2 can scavenge various free radicals to reduce oxidative stress at the site of inflammation, endowed the hydrogels with antioxidant properties. Interestingly, growth factors released by PRP assisted the tissue repair by promoting the formation of new capillaries. CMCS as a backbone not only showed good biocompatibility and biodegradability but also played a significant role in maintaining the sustained release of growth factors. In addition, incorporating PVP enhanced the tissue adhesion and mechanical properties. The multifunctional composite antioxidant hydrogels have good swelling properties and biodegradability, which is completely degraded within 28 days. Thus, the antioxidant CMCS/PVP/MoSe2/PRP hydrogels provide a new idea for designing ideal multifunctional wound dressings.

All-in-one hydrogel patches with sprayed bFGF-loaded GelMA microspheres for infected wound healing studies

The current wound healing process faces numerous challenges such as bacterial infection, inflammation and oxidative stress. However, wound dressings used to promote wound healing, are not well suited to meet the clinical needs. Hyaluronic acid (HA) not only has excellent water absorption and good biocompatibility but facilitates cell function and tissue regeneration. Dopamine, on the other hand, increases the overall viscosity of the hydrogel and possesses antioxidant property. Furthermore, chitosan exhibits outstanding performance in antimicrobial, anti-inflammatory and antioxidant activities. Basic fibroblast growth factor (bFGF) is conducive to cell proliferation and migration, vascular regeneration and wound healing. Hence, we designed an all-in-one hydrogel patch containing dopamine and chitosan framed by hyaluronic acid (HDC) with sprayed gelatin methacryloyl (GelMA) microspheres loaded with bFGF (HDC-bFGF). The hydrogel patch exhibits excellent adhesive, anti-inflammatory, antioxidant and antibacterial properties. In vitro experiments, the HDC-bFGF hydrogel patch not only showed significant inhibitory effect on RAW cell inflammation and Staphylococcus aureus (S. aureus) growth but also effectively scavenged free radicals, in addition to promoting the migration of 3 T3 cells. In the mice acute infected wound model, the HDC-bFGF hydrogel patch adhered to the wound surface greatly accelerated the healing process via its anti-inflammatory and antioxidant activities, bacterial inhibition and pro-vascularization effects. Therefore, the multifunctional HDC-bFGF hydrogel patch holds great promise for clinical application.

Study on Bonding Behavior between High Toughness Resin Concrete with Steel Wire Mesh and Concrete

This paper investigates the interfacial bonding behavior between high toughness resin concrete with steel wire mesh (HTRCS) and concrete. A total of five sets of fifteen double shear specimens were tested for parameters including concrete strength and material properties of HTRCS composites. The test results showed that the failure mode of DS1 specimens was partial debonding and fracture, and the rest of the specimens were the fracture of HTRCS. The concrete strength and reinforcement ratios of HTRCS composites were positively correlated with interfacial adhesion properties. When the concrete strength was increased from C30 to C40 and C50, the ultimate load increased by 43.4% and 43.2%, respectively. The ultimate load capacity increased by 32.1%, with the reinforcement ratio of HTRCS composites increasing from 1.05% to 1.83%. Moreover, the bonding slip model and the bearing capacity formula for the interface between HTRCS composites and concrete were proposed, and the calculation values were in good agreement with the test values, with an average value of 0.978.