Water Production Research Articles

Performance of a direct-expansion solar-assisted heat pump for domestic hot water production in Algeria

The focus of this study is to investigate the energy performance of a direct-expansion solar-assisted heat pump water heating system (DX-SAHPWH). The system consists of an unglazed solar collector-evaporator, which can absorb heat from solar energy and air ambient simultaneously, a condenser in the form of a coil immersed in a hot water storage tank, a thermostatic expansion valve and a hermetic reciprocating compressor. The performance of the heat pump system is evaluated using a developed mathematical model under Matlab code. The modelling method is based on lumped and distributed parameter approach of different system components. Numerical calculations were carried-out to study the influence of different parameters, such as ambient temperature, solar radiation intensity and polytropic index on the system performance. Additionally, in order to evaluate the long-term system performance, the system’s model was applied on a case study of a single-family building located in Djelfa (Algeria), which represents the coldest arid region of the country. The results showed that the solar radiation intensity and ambient temperature have significant effects on the heat pump performance. A COP of 5.9 and a collector-evaporator efficiency of 1.9 were obtained at high solar radiation of 850 W/m2 resulting in lower heating time (29 min). In addition, results revealed that the system can operate even at lower ambient temperature due to its ability to take advantage of heat from the ambient air. The results from the case study gave a COP ranging from 2.3 to 3.8, which enhance the promising adoption of this system in domestic hot water production to respond to people daily life needs with clean, abundant and renewable energy.

Techno-economic optimization and working fluid selection of a biogas-based dual-loop bi-evaporator ejector cooling cycle involving power-to-hydrogen and water facilities

Biogas-fueled decentralized energy systems featuring gas turbines emerge as pivotal players in the quest for more adaptable and eco-friendly energy solutions. This study presents the design of a cutting-edge multigeneration system that harnesses the potential of a gas turbine coupled with ejector-driven dual-loop bi-evaporator technology, reverse osmosis desalination, proton exchange membrane electrolysis, and an organic Rankine cycle. The research encompasses an extensive sensitivity analysis and deploys a genetic algorithm-based optimization technique. Through meticulous Optimization, the system achieves remarkable outcomes, including electricity generation, cooling capacity, heating capacity, desalinated water production, and hydrogen yield, measured at 957.3 kW, 231.4 kW, 272.3 kW, 7.336 kg/s, and 0.99 kg/h, respectively. Notably, this performance surpasses the base case by 2% and 8.9%, yielding exergy efficiency and total unit cost improvements of 33.3% and 16.4 $/GJ. Among the critical decisions made was selecting an organic working fluid for the organic Rankine cycle. Through rigorous evaluation, isobutene emerged as the optimal choice, demonstrating significantly improved output power compared to alternatives. Isobutane as the working fluid led to a substantial increase in overall exergy efficiency and a resultant total unit cost of 18.06 $/GJ, accompanied by an impressive 23.48% exergy efficiency.

Interlayer Structure Manipulation of FeOCl/MXene with Soft/Hard Interface Design for Safe Water Production Using Dechlorination Battery Deionization.

Suffering from the susceptibility to decomposition, the potential electrochemical application of FeOCl has greatly been hindered. The rational design of the soft-hard material interface can effectively address the challenge of stress concentration and thus decomposition that may occur in the electrodes during charging and discharging. Herein, interlayer structure manipulation of FeOCl/MXene using soft-hard interface design method were conducted for electrochemical dechlorination. FeOCl was encapsulated in Ti3C2Tx MXene nanosheets by electrostatic self-assembly layer by layer to form a soft-hard mechanical hierarchical structure, in which Ti3C2Tx was used as flexible buffer layers to relieve the huge volume change of FeOCl during Cl- intercalation/deintercalation and constructed a conductive network for fast charge transfer. The CDI dechlorination system of FeOCl/Ti3C2Tx delivered outstanding Cl- adsorption capacity (158.47 ± 6.98 mg g-1), rate (6.07 ± 0.35 mg g-1 min-1), and stability (over 94.49% in 30 cycles), and achieved considerable energy recovery (21.14 ± 0.25%). The superior dechlorination performance was proved to originate from the Fe2+/Fe3+ topochemical transformation and the deformation constraint effect of Ti3C2Tx on FeOCl. Our interfacial design strategy enables a hard-to-soft integration capacity, which can serve as a universal technology for solving the translational problem of electrode volume expansion.

Investigating Performance of Hybrid Photovoltaic–Thermal Collector for Electricity and Hot Water Production in Nigeria

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels, considering Nigeria as a case study. It is found that high solar radiation in Nigeria increases the surface temperature of PV panels above 25 °C of the optimal operating temperature. The redundant energy gain from solar irradiance creates heat at the rear of solar panels and reduces their efficiency. Cooling mechanisms are therefore needed to increase efficiency. In this study, we demonstrated a unique hybrid system design employing a heat exchanger at the back of the panel, with water circulated through the back of the PV panel to cool the system. The system was simulated using TRNSYS at three locations in Nigeria—Maiduguri, Makurdi, and Port Harcourt. The results of the peak annual electrical power output in Maiduguri give a power yield of 1907 kWh/kWp, which is the highest, due to a high solar radiation average of 727 W/m2 across the year. For Makurdi, the peak annual electrical power output is 1542 kWh/kWp, while for Port Harcourt the peak power output is 1355 kWh/kWp. It was observed that the surface temperature of Polycrystalline Si-PV was decreased from 49.25 °C to 38.38 °C. The electrical power was increased from 1526.83 W to 1566.82 W in a day, and efficiency increased from 13.99% to 15.01%.

Versatile GO/ANFs Aerogel for Highly Efficient Solar-Powered Water Purification in Wide Environments.

Solar-driven interfacial evaporation is a very promising choice for producing clean water. Despite the considerable investigation of pure NaCl brine purification, solar-driven complex water purification, such as real-world seawater desalination as well as domestic and industrial wastewater treatment, has rarely been investigated, mainly due to its compositions being much more complicated than NaCl brine. Herein, we developed a graphene oxide/aramid nanofiber (GO/ANFs) aerogel by a freeze-drying process. The GO/ANFs aerogel combined opened porous microchannels, superhydrophilicity, anti-oil-fouling capacity, enhanced broad-spectrum light absorption (more than 92%), and good solar/heat management. These integrated properties enabled the GO/ANFs aerogel to be an advanced solar interfacial evaporator for efficient freshwater production with the characteristics of localized heat conversion, quick water transport, and salt crystallization inhibition, and the rate of steam production rate was as high as 2.25 kg m-2 h-1 upon exposure to 1 solar irradiation. Importantly, the high-water-vapor generation rate was maintained even under complicated conditions, including real-world seawater, dye water, emulsions, and corrosive liquid environments. Considering its promising adaptability to a wide range of environments, this work hopes to inspire the development of brine desalination, wastewater purification, clean water production, and solar energy utilization.

Fast and Reliable History Matching of Channel Reservoirs Using Initial Models Selected by Streamline and Deep Learning

Abstract Ensemble-based methods involve using multiple models for model calibration correct initial models based on observed data. The assimilated ensemble models allow probabilistic analysis of future production behaviors. It is crucial to use good initial models to obtain reliable history matching and prediction of both oil and water productions especially for channel reservoirs having high uncertainty and heterogeneity. In this study, we propose a fast and reliable history matching method by selecting good initial models using streamline and deep learning. The proposed method is applied to two cases of 3D channel reservoir generated by SGeMS and GAN. The proposed method offers predictions with accuracy improvement more than 20% for oil and 10% for water productions compared with two other model selection methods. It also reduces the overall simulation time by 75% compared to the method of using all initial models.

Optimizing the water-ecosystem-food nexus using nature-based solutions at the basin scale

The water ecosystem food (WEF) nexus duly acknowledges the complex interdependencies among water, ecosystems, and food production, underscoring nature based solutions (NBS) as an efficacious strategy for navigating these interconnections. In this research, four different NBS (terraces, riparian forest, livestock management and agro ecological practices) were assessed in terms of their impact to WEF nexus. The Karst-SWAT and the one-dimensional integrated critical zone (1D-ICZ) models were used to simulate the impact of NBS on water quantity and quality as well as on soil ecosystem services of Koiliaris River Basin, which serves as an illustrative example of a basin that has experienced severe soil and biodiversity degradation. The Karst-SWAT model showed that a combination of NBS of terraces and riparian forest can reduce soil erosion and the sediment load by 97%. The 1D-ICZ model successfully simulated the soil-plant-water system and showed that agro ecological practices affect biomass production, carbon and nutrient sequestration, soil structure and geochemistry.

Direct Electrooxidation of Ammonia-Enriched Wastewater Using a Bipolar Membrane-Integrated Electrolytic Cell

The treatment of reject water containing concentrated ammonia and non-biodegradable organics is a challenging task in wastewater treatment plants. To address this problem, we propose a novel process consisting of a selective ammonium-exchange resin and an ammonia electrooxidation reaction (AmER-AOR). Because an alkaline condition is essential for direct ammonia oxidation, the use of a bipolar membrane (BPM) was helpful. Nonetheless, an initial pH of 13 and KOH addition were required to maintain a high alkalinity for the complete elimination of ammonia. The linear sweep voltammogram elucidated the high pH requirement and ammonia oxidation promotion. When the current density varied from 30 to 80 mA cm−2, 60 mA cm−2 showed the highest current efficiency (30.39%) and the lowest specific energy demand (95.3 kWh/kg-N), indicating the most energy-effective condition. Increasing the initial concentration of ammonia from 0.1 M to 0.5 M improved the current efficiency (51.57%), demonstrating an additional energy-effective strategy for the AmER-AOR. The energy efficiency of pure H2 production in the cathodic chamber was 30%. To estimate the viability for practical applications, reject water collected from a local wastewater treatment plant was applied in the AmER-AOR. Notably, no significant difference in the ammonia removal rate was observed with synthetic wastewater. To the best of our knowledge, this is the first study that employs a BPM as a separator and OH− supplier for direct ammonia oxidation. Our findings reveal that the AmER-AOR with a BPM has promising practical applicability in the treatment of reject water and energy production.

Analysing Spatiotemporal Variability of Chlorophyll-a Concentration and Water Surface Temperature in Coastal Lagoons of the Ebro Delta (NW Mediterranean Sea, Spain)

Coastal lagoons are highly productive transitional water bodies threatened by human factors and vulnerable to global climate change effects. Monitoring biophysical parameters in these ecosystems is crucial for their preservation. In this work, we used Sentinel-2 and Landsat imagery combined with in situ data to (1) develop preliminary algorithms for retrieving the Chl-a concentration and water surface temperature of six lagoons located in the Ebro Delta (NE Mediterranean Sea, Spain), and to (2) compute maps and trend lines for analysing their spatiotemporal evolution from 2015 to 2022. Our findings showed that the algorithms’ accuracy ranged from 72% to 78% and had limited potential under high Chl-a concentration regimes. Even so, they revealed the lagoons’ trophic status, usual fluctuations, and deviations of both parameters attributed to seasonal (i.e., light and temperature) and short-term physical (i.e., winds) forcing, as well as valuable spatial patterns potentially useful for conservation efforts and land use planning. Future work will focus on the acquisition of a larger in situ data sample under a range of environmental conditions to improve the algorithms’ robustness, which in turn will allow the investigation of natural and human factors controlling the dynamics of the two investigated parameters.

Biomimetic solar evaporator for continuous clean water production with synergistic organic dye wastewater remediation

Solar-driven water evaporation is recognized as an environment-friendly technology for sustainable clean water generation, serving the needs of both desalination and wastewater purification. However, its practical application is constrained by challenges such as single functionality and significant salt accumulation. Inspired by the transpiration of vascular plant, this work introduces a scalable and cost-effective biomimetic evaporator (PyCOF/Tri-Layers), consisting of a biomimetic hierarchical fibrous membrane (Tri-Layers) and a composite photothermal layer (PyCOF). Furthermore, the PyCOF composite, featuring an aloe-like flower structure, enhances the light trapping (95.1 %) through multiple scattering, realizing simultaneous desalination and azo dye degradation. Based on the PyCOF/Tri-Layers evaporator, we demonstrate a suspended multi-section hanging evaporation structure sustaining a consistent evaporation rate of approximately 1.41 kg m−2 h−1 over 15 days without salt accumulation, achieving above 99.3 % removal of dye pollutants within 120 min under one sun irradiation. Moreover, in outdoor experiments, the improved evaporator realizes a daily clean water yield rate of 8.73 kg m−2 d−1, and the collected water is suitable for supporting crop cultivation within an integrated solar desalination-cultivation system. This work not only provides a one-stone-two-birds approach for generating clean water from polluted seawater, but also presents promising possibilities for offshore self-sustainable agriculture production.

Enchasing Production Planning and Inventory Management : A Quantitative Approachto Forecasting for Bottled Mineral Water Products at PT Arima

PT Arima is a company engaged in the production of bottled mineral water. The demand for bottled mineral water is experiencing fluctuations, with demand increasing at the end, so companies must carry out optimal production planning to avoid stock buildup. Production planning at PT Arima is carried out by identifying demand levels using quantitative forecasting methods, namely moving average (n = 3) and exponential smoothing (α = 0.05) to maintain optimal production levels and stock in the warehouse does not accumulate. The results of processing the level of forecasting accuracy using 12 months of demand data obtained using the moving average method showed that the production level = 39,733 boxes in January 2024. MAD = 3733.22; MSE = 21566024.78 and MAPE = 0.10. Based on the exponential smoothing method, the production level = 38,081 boxes in January 2024. MAD = 5773.50; MSE = 43466303 and MAPE = 0.15. Based on the results of comparing the MAPE values ​​of the two forecasting methods, the lowest MAPE value was obtained, namely the average method (n=3) of 0.10 with the production level of bottled mineral water to maintain optimal supply conditions in January 2024 of 39,733 boxes.

Scaled solar-driven atmospheric water harvester with low-cost composite sorbent

The rapidly developing atmospheric water harvesting (AWH) technology can convert inexhaustible water vapor from the air into liquid water, which has become a highly potential technological solution for humanity to cope with water crises. Unlike the energy-intensive method of cooling air below the dew point to achieve water production, the sorption-based AWH (SAWH) system with adsorbents can achieve efficient water production above the dew point temperature in arid areas using low-grade energy represented by solar energy. However, current research of SAWH focuses mainly on small-scale devices, and practical verification with large-scale experimental equipment is still lacking. In addition, most of these verifications used auxiliary equipment to support the demonstration, and the expensive chosen adsorbent to pursue full-day adsorption capacity further limited the practical application of this technology. Based on this, from developing composite adsorbents to scalable solar-driven devices, this work proposes a complete technical solution to meet practical needs in arid regions. The developed low-cost composite adsorbent has an adsorption capacity of 0.52 g g−1 at 30 °C@60 % of relative humidity (RH), and its adsorption capacity can be significantly improved with the increase of RH (e.g., 0.97 g g−1 at 30 °C@80%RH), which is very beneficial for the utilization of high-humidity adsorption environments at night. The developed adsorbent, combined with a scaled device optimized by thermal design, achieved a high-level water production capacity of 355 g in a day and 0.74 L m−2 in practical field experiments.

Heat recovery of multistage circulated permeate gap membrane distillation for energy-efficient water production

Addressing the challenges of energy efficiency in the desalination industry, this study proposed an energy-efficient water desalination system, focusing on the novel innovative approach of gap water circulation in permeate gap membrane distillation (PGMD) systems. A counterflow multistage is considered and analyzed using combined heat-mass transfer modeling. In comparison to conventional PGMD configurations, the introduction of gap water circulation has visibly emerged to increase water productivity while decreasing energy consumption. This research systematically explored the impact of this innovation, employing a comprehensive methodology that includes modifying flow chamber configurations and analyzing operational parameters. The study was performed at different seawater intake flow rates, intake temperature, feed injection temperature, and different number of stages. It was found that increasing the number of stages in the counterflow configuration presented better energy efficiency and higher feed recovery ratios at different conditions. A remarkable reduction in Specific Thermal Energy Consumption (STEC) to 92 kWh/m3, coupled with a notable increase in flux values reaching 28 kg/m2.hr for the alternative modules due to the intensified turbulence and mixing. The study demonstrated the potential of gap water circulation in significantly enhancing the energy efficiency and productivity of MD systems compared to conventional PGMD systems.

Multifunctional nanofiber membrane with antifouling properties for efficient seawater desalination and wastewater purification

Solar-driven water evaporation has attracted widespread attention for its extensive applications in the production of clean water from seawater and wastewater. However, most of the designed evaporators focus on evaporation performance but ignore the antifouling ability, particularly the evaporator used for wastewater treatment. Herein, a cellulose acetate (CA)/polyaniline (PANI)/copper sulfide (CuS) nanofiber membrane with a core-shell structure was designed as an evaporator. The super-hydrophilic CA nanofiber membrane was obtained by deacetylation, which could provide sufficient water for water evaporation. Meanwhile, the in situ polymerization of PANI on CA nanofiber facilitates the growth of a uniform CuS layer on the fibers. Consequently, the synergistic effect between PANI and CuS not only improved the light absorption and photothermal conversion ability but also enhanced the photocatalytic ability of composite membranes. The d-CA/PANI/CuS evaporator exhibited a high evaporation rate of 1.45 kg m−2 h−1 under one solar radiation. Due to the excellent photocatalytic self-cleaning ability, the average evaporation rate of d-CA/PANI/CuS nanofiber membrane for methylene blue (MB) solution remained at 1.42 kg m−2 h−1 in a long-term evaporation experiment. This work may shine a new light on the design of novel antifouling evaporators with photocatalytic self-cleaning capability for seawater desalination and wastewater treatment.

Theoretical and experimental analysis of sea ice centrifugal desalination and supercooled water production for slurry ice

This study presents a comprehensive investigation of centrifugal desalination of sea ice and the production of slurry ice from supercooled water. A mathematical model for centrifugal desalination was established and validated through experiments. The results displayed a high level of accuracy in both the theoretical and experimental analyses, with an average goodness of fit of approximately 0.94. An experimental platform is established to produce supercooled water, using different types of water as ice-making solutions. The slurry ice is more suitable for centrifugal desalination than solid ice, and it can be obtained by disrupting the supercooled state of supercooled water, with finer ice crystals produced through ultrasonic supercooling release compared to natural methods. Decreasing the refrigerant temperature benefits enhancing the supercooling degree while compromising the stability of supercooled water generation. The stability is investigated with variations in refrigerant temperature to generate a solution temperature 2.0 °C higher than the refrigerant. When the supercooling degree is 1.0 °C, all of these solutions have a high stability of 80 %, however, it becomes worse as the supercooling degree increases. At the supercooling degree of 2.0 °C, saltwater has the highest stability of only 35 %, and seawater has the lowest stability of 15% due to its complicated composition. This phenomenon also reveals that conducting experiments using saline solution instead of seawater can lead to significant misleading effects. Additionally, the impact of flow rate on the supercooling degree is investigated, showing a minor influence.

Geochemical tracers associated with methane in aquifers overlying a coal seam gas reservoir

Understanding inter-aquifer connectivity or leakage of greenhouse gases and groundwater to aquifers overlying gas reservoirs is important for environmental protection and social licence to operate. Australia's Great Artesian Basin (GAB) is the largest artesian groundwater system in the world with groundwater extracted for agriculture, livestock, mines, energy, private or town water supply. Microbial coal seam gas (CSG) and production water are also extracted from the GAB. Here a range of groundwater tracers is used to investigate the potential for gas and groundwater connectivity between the CSG reservoir and aquifers.The GAB aquifer and alluvium contained a range of methane concentrations (0.001 to 2100 mg/L) that exhibit an increase with depth and δ13C-CH4. Aquifer and alluvium groundwater 87Sr/86Sr were in the range 0.7042 to 0.7082. CSG production waters however had non-radiogenic, distinctive 87Sr/86Sr signatures <0.7036, indicating a lack of significant groundwater leakage. One gassy aquifer bore with 160 mg/L methane conversely has 87Sr/86Sr, δ13C-CH4, δ2H-CH4 and δ13C-DIC values overlapping the CSG waters. In several aquifers δ34S-SO4 and δ18O-SO4 are sourced from windblown surface salts of inland Australian playa lakes in recharge waters. Bacterial sulphate reduction is additionally occurring in a regional aquifer. Cosmogenic isotopes and tritium show recent recharge and mixing with older groundwaters in several shallow aquifers.Groundwater and gas signatures indicate that leakage of groundwater and methane from the CSG reservoir was not occurring in the majority of areas investigated here. Methane was consistent with in situ generation in shallow GAB aquifers by primary microbial CO2 reduction or acetate fermentation. Connectivity of one alluvial bore and the underlying GAB aquifer could not be completely ruled out. Separately, one gassy Springbok GAB aquifer bore is either connected to the underlying CSG gas reservoir, or has in situ secondary microbial CO2 reduction producing methane from interbedded coal within the aquifer. This study is relevant to other basins in Australia and internationally where gas is observed in aquifers that overly conventional, unconventional or coal seam gas reservoirs.

Integration of IoT Technologies for Enhanced Monitoring and Control in Hybrid-Powered Desalination Systems: A Sustainable Approach to Freshwater Production

In the face of our rapidly expanding global population, the necessity of meeting the fundamental needs of every individual is more pressing than ever. Human survival depends upon access to water, making it a vital resource that demands novel solutions to ensure universal availability. Although our planet is abundant in water, 97.5% of it is saltwater, compelling nations to investigate ways to make it suitable for consumption. Seawater desalination is becoming increasingly vital for water sustainability. While seawater desalination offers a solution, existing methods often grapple with high energy consumption and maintaining consistent water quality. This paper proposes a novel hybrid water desalination system that addresses these limitations. Our system leverages solar energy, a readily available renewable resource, to power the desalination process, significantly improving its environmental footprint and operational efficiency. Additionally, we integrated a network of sensors and the Internet of Things (IoT) to enable the real-time monitoring of system performance and water quality. This allows for the immediate detection and improvement in any potential issues, ensuring the consistent production of clean drinking water. By combining solar energy with robust quality control via IoT, our hybrid desalination system offers a sustainable and reliable approach to meet the growing demand for freshwater.

Synergizing theory and experiment: Enhancing solar distillation performance with external reflector in a passive 4-stage model

Passive multi-stage solar distillers are pivotal in sustainable water purification, effectively utilizing solar energy. This study addresses the underexplored impact of reflective characteristics by integrating an aluminum reflector with radiation-trapping properties into a passive 4-stage solar distiller leveraging both experimental and theoretical methodologies. The influence of reflector height and angle on solar input, water production rate, and the Gain Output Ratio (GOR) was examined. Findings revealed a water production rate of 5.98 kg∙m−2hr−1and a GOR enhancement to 156 % at an optimal reflector setup of 40 mm height and 120° angle. Theoretical analysis assessed heat distribution and thermal efficiency across various air gaps and solar radiation levels. Evaporation emerged as the dominant heat mechanism, achieving 91 % thermal efficiency in the first stage with a 6.5 mm air gap and 1.50 kW∙m−2 of reflected solar radiation. Conversely, a 16 mm gap significantly lowered efficiency to 72 % in the last stage due to increased lateral heat loss. Transient analysis of the newly defined dissipation percent showed that narrower air gaps boosted heat retention in the distiller for evaporation and greater heat dissipation through the last stage, optimizing heat recycling for thermal applications. Increasing the solar input leads to sustained dissipation capacity.

Efficient sulfamethoxazole removal, water recovery and electricity generation were achieved simultaneously by osmotic microbial fuel cell in treating antibiotic wastewater

Microbial fuel cell (MFC) processes are associated with poor effluent quality when treating antibiotic wastewater. This study innovatively applied osmotic microbial fuel cell (OsMFC) technology to treat antibiotic wastewater while achieving the efficient removal of sulfamethoxazole (SMX), producing high-quality water, and generating electricity. During the stable operation of the OsMFC system, the chemical oxygen demand (COD) removal efficiency reached 80.1%, and the SMX removal efficiency reached 99.3% owing to forward osmotic membrane interception and biodegradation. The high-quality water production rate was 25% ± 5%. Interestingly, the addition of SMX improved the electrochemical performance of the system. The maximum power density was 4,642.4 mW/m3, and the internal resistance was only 230.7 Ω. During long-term operation of the system, membrane fouling was slight, and proteins were the main component of the fouling, followed by α-D glucopyranose polysaccharides and β-D glucopyranose polysaccharides. This study provides a new approach for the treatment of antibiotic wastewater and a novel method for the biodegradation of challenging emerging pollutants.

Experimental investigation on the effect of nano-enhanced phase change materials on the thermal performance of single slope solar still

Solar desalination is employed to create drinkable water from salt water. Using solar energy saves money and supplies clean, renewable fresh water. Nano-enhanced Phase change materials (NEPCM) and nano-enhanced absorption were utilized in this analysis to increase the capacity of solar desalination. Increased solar energy absorption makes anthracite content in saline water. CuO and AlN nanoparticles at 0.2 wt% and 0.4 wt% were combined in paraffin wax and injected into 12 copper pipes on the anthracite to boost the thermal characteristics of PCM. Copper pipes coated with dark paint containing scattered CuO nanoparticles to improve thermal conductivity. According to the findings, solar still production amplifies by 55.8 % and 49.5 %, respectively. Copper Oxide and Aluminium Nitride nanoparticles, each containing 0.2 wt%, lowered the melting temperature to 2.2ºCand 1.9ºC, respectively. It found that the CPL values of the Single slope solar still were 0.2₹/L and 8.26₹/L with the nano-enhanced PCM at 0.4 wt% CuO and AlN. The nano-coating also achieved a 5.7 % rise in the water production rate of the solar still.