Processing Temperature Research Articles

Study on Multi-Parameter Variation of Smoke Flow in Inclined Roadway Fire

ABSTRACT Based on the fluid similarity theory, a “Mine inclined roadway fire simulation experimental system” with similarity ratio of 1:20 is established. The temperature, velocity, density and dynamic pressure of fire smoke under different inlet wind speed (0.5 m/s, 1.0 m/s, 1.5 m/s) were tested and analyzed, and the distribution of temperature, velocity, density and dynamic pressure of inclined roadway during fire was simulated and analyzed by Ansys numerical simulation software. The research shows that: The higher the inlet wind speed, the faster the heat diffusion and the temperature field tends to be flat and long, the wind speed changes in advance and the change is drastic, the gas density decreases, the dynamic pressure first decreases and then increases and then tends to stabilize, but the change trend of temperature, wind speed, gas density and pressure in the overall combustion process remains unchanged. The numerical analysis results are in good agreement with the experimental results. By studying the change law of smoke temperature, velocity, density and dynamic pressure of coal mine inclined roadway fire, the theory of coal mine roadway fire is further perfected, and the level of coal mine fire prevention and rescue is improved.

Low temperature processing and characterization of novel ceria based electrolyte composition Ce0.8−xGd0.1Bi0.1TixO2−δ (x = 0.05,0.1) for intermediate temperature SOFC application

Low temperature processing and characterization of novel ceria based electrolyte composition Ce0.8−xGd0.1Bi0.1TixO2−δ (x = 0.05,0.1) for intermediate temperature SOFC application

Microbiological quality of vegan alternatives to dairy and meat products in England during 2022-3.

Plant-based alternatives to meat and dairy products have become increasingly popular in the UK. Despite a public perception that they have a relatively low microbiological risk, outbreaks of illness have been linked with these foods. This study aimed to assess the microbiological safety and quality of vegan alternatives to dairy and meat products available in England. Samples were collected between September 2022 and March 2023 from retail, production, and catering premises, and tested for a range of bacterial pathogens and hygiene indicators using standard procedures. A total of 937 samples were tested, of which 92% were of a satisfactory microbiological quality, 3% were borderline, and 5% were unsatisfactory. Those interpreted as unsatisfactory were due to elevated counts of Enterobacteriaceae and Escherichia coli (indicators of poor hygiene) rather than pathogenic microorganisms. Listeria monocytogenes was present in five samples of tofu, all from the same producer (all at counts of<100 CFU g-1), while other Listeria species were detected at counts of<20 CFU g-1 in two burgers and two 'vegan chicken' products. The majority of samples did not have pH and water activity values that would significantly contribute to preventing microbial growth: 62.4% had pH>5.0 and 82.4% had Aw>0.94. The majority of vegan products examined were of a satisfactory quality, but results demonstrate that microbiological control must be maintained using appropriate processing and storage temperatures, and application of a safe length of shelf life.

Sctudies on adsorption of Brilliant Green from aqueous solution onto nutraceutical industrial pepper seed spent

The study proposed the removal of Brilliant Green, a cationic dye, by adsorption process from wastewater solution utilizing a low-cost adsorbent such as Nutraceutical Industrial Pepper Seed Spent (NIPSS). The study comprises an investigation of the parametric influence on the adsorption process. The parameters identified are pH, dye concentration, process temperature, quantity of the adsorbent, and particle size. The study of statistics found from experiments was carried out by incorporating Freundlich, Brouers-Sotolongo, Langmuir, Toth, Sips, Jovanovic, and Redlich-Peterson isotherm models. The adsorption kinetics were determined by implementing pseudo-first-order and second-order models, diffusion film models, and Dumwald-Wagner and Weber-Morris models. The experimental adsorption capacity qe was found to be about 130 mg/g. This value was closest to the maximum adsorption of 144.6mg/g predicted by the Brouers-Sotolongo isotherm which had a correlation coefficient (R2) of 0.998. The adsorption kinetics data was confirmed to be a pseudo-second-order model. The change in free energy, enthalpy change, and entropy change were vital thermodynamic factors in concluding that adsorption is almost spontaneous and endothermic process. Change in enthalpy (ΔH°) reduced value indicates the physical nature of the process. The adsorption of BG dye on the adsorbent surface was authenticated by FTIR spectroscopy and SEM imaging. A Central Composite Design (CCD) Quadratic model under Response Surface Methodology (RSM) was implemented for statistical optimization of adsorption capacity for the five parameters studied, namely, time, temperature, concentration of the dye, weight of the adsorbent, and pH. Software Design Expert 7.0 was used to evaluate 3D contour plots. The process of optimization yielded a value of 350 mg/g. Thus, incrementing the adsorption process by 84.2 %. The study provides insights on various dye and adsorbent interaction possibilities and derives that NIPSS is an efficient adsorbent to extract BG dye from wastewater solutions.

Enrichment of Chlorophyta growth via cerium oxide and utilized for hydrogen production via hydrothermal gasification process

Abstract The growing interest in alternative fuels stems from the need to address energy security and economic challenges. Hydrogen fuel is considered a promising solution due to its versatility, efficiency, and potential for zero emissions, as well as continuous technological advancements and increasing policy support. This study intends to enhance Chlorophyta growth by incorporating different volume percentages of cerium oxide (CeO2) as feedstock for hydrogen production through hydrothermal gasification. The research findings indicate that the highest concentration (0.2 vol %) of CeO2 resulted in the maximum growth of 0.63 μ/day, which was utilized for hydrogen extraction. Additionally, the investigation explored the impact of Chlorophyta algae loading (0.05-0.15 g/mL) and processing temperature (500-650°C) on molar fraction, hydrogen yield, gasification efficiency, carbon efficiency, and total hydrogen production. Higher feedstock (0.15 g/mL) and gasification temperature (650°C) were found to improve hydrogen fraction (61.8%), yield (10.2 mol/kg), gasification efficiency (43.8 %), and total hydrogen production (62.5%).

Comparison of conventional and green approaches to the synthesis of aromatic Schiff bases

Abstract The chemical industry is one of the key elements in improving the quality of human life. At the same time, it generates pollution influencing the ecosystem and our health. To limit or remove some of the reasons of pollution for two decades less harmful approaches to the synthesis of various organic compounds were developed. Among organic compounds, azomethines, also known as Schiff bases, are of particular interest in biochemistry, medicine, and pharmacy. For over twenty years many novel approaches to the synthesis of these compounds have been investigated. Toxic solvents (benzene, toluene) have been replaced with water, fruit juice, or white egg, and in many cases, temperature and time of process were significantly reduced. In the review, conventional and green approaches to the synthesis of Schiff bases are presented with a focus on the effectiveness of these methods, including advantages and disadvantages.

Experimental and simulation study on lean combustion characteristics of passive pre-combustion chamber ignition boosted GDI engine

In order to verify the potential application of passive pre-combustion chamber technology in commercial GDI engines, the efficiency characteristics, combustion characteristics (CA50, Knock Index and COV) and emission characteristics of a pre-combustion chamber ignition engine in a boosted environment were studied by three-stage injection strategy to form a lean burn environment (λ = 1.3). A 3D simulation model of pre-combustion chamber ignition engine is established. Combined with the engine bench test results, the process of intake, mixture formation, combustion and emission generation under different working conditions is simulated by simulation method. The development process of TKE (turbulent kinetic energy), air-fuel ratio, temperature and combustion emissions in the main/pre-combustor is studied. It is found that under high load conditions in boosted pre-combustion chamber engine, the average knock index can be controlled between 2 and 3.4 bar, and the COV can be controlled between 3% and 3.5%. The indicated thermal efficiency reaches over 40% within the load range of IMEP from 10 to 14 bar. When the load increases, NOx and soot emissions show a downward trend, the HC and CO emissions slight increase. The pre-combustion chamber engine exhibits a tumble intake pattern around the cylinder axis perpendicular to the cylinder axis. The TKE reaches its maximum value 20 CAD before the top dead center and then rapidly decreases. The use of a three-injection strategy can form a uniform stratified mixture at the ignition moment. The fuel air equivalence ratio in the ignition area of the pre-combustion chamber is 0.8–0.9, slightly higher than the average fuel air equivalence ratio of 0.75.

Bioremediation of textile wastewater using Bacillus cereus isolated from refinery site: Comparative analysis of free and immobilized cells systems

The textile industries consume a considerable amount of freshwater and discharge untreated or semi-treated pollutants to the environment. Azo dyes, generally employed in textile manufacturing industries, have a hazardous impact on the ecosystem. Incomplete treatment of wastewater containing azo dyes discharges into the aquatic system, which has recalcitrant and toxic properties. Hence, the need for cost-effective and high-performing technologies is essential. In this direction, bacterial degradation is considered an economically viable and efficient technique for the treatment of Active blue (AB) dye. Polyurethane foam (PUF) is a low-cost and hydrophilic material with a microporous structure, which offers an excellent surface-to-volume ratio. Hence, PUF was preferred for the immobilization of isolated bacterial species. For this, a dye-degrading gram-positive bacteria namely Bacillus cereus GS2 IIT (BHU) was isolated from the petroleum sludge. A comparative analysis between free and immobilized cell systems was carried out by varying the process parameters, i.e., batch time, pH, temperature, glucose concentration, and initial AB dye concentration. The corresponding optimum conditions were found to be 6.0 days, 6.5, 30 °C, 1.0 g/L, and 50 mg/L, respectively. The immobilized cell system exceeds the dye removal efficiency (RE) by 10. 7 % compared to the free cell system. The packed bed bioreactor could be able to deliver 98.56 % of dye removal at an inlet loading rate of 30 mg/L d and 50 mg/L of initial dye concentration.

Jet Array Design for the Physical Tempering Process of Ultrathin Glass

Jet Array Design for the Physical Tempering Process of Ultrathin Glass

Including detailed chemistry features in the modeling of emerging low-temperature reactive flows: A review on the application to diluted and MILD combustion systems

Developing and optimizing new reactive systems with carbon-neutral fuels like biofuels, e-fuel, hydrogen, or ammonia is crucial for sustainable energy. This requires advanced technologies capable of fuel flexibility, high efficiency, and minimal pollutant emissions. However, these energy carriers still produce pollutants, especially NOx. To address this, engineers aim to lower combustion process temperatures by adopting different strategies such as burned gas recirculation, staging or increasing the air-to-fuel ratio. Yet, lean flames, though effective at emission reduction, are prone to instability and extinction, posing safety and mechanical risks. Emerging technologies like MILD Combustion, based on burned gas recirculation and reactant dilutions offer interesting solutions. The review article begins by synthesizing experimental studies and numerical simulations of MILD turbulent combustion. It then explores fundamental phenomena specific to diluted combustion (where MILD regimes are included as sub-sets), including autoignition and flame propagation. Using high-fidelity simulations and advanced experiments, it examines flow and mixing roles in reactive zones stabilization. Moving forward, the review paper addresses the inclusion of detailed chemical properties in modeling turbulent combustion systems. Scientific challenges revolve around modeling the intricate interactions between combustion chemistry and flow turbulence while maintaining computational efficiency compatible with industrial constraints. To address this, various simplified chemistry methods – such as reduced, tabulated, or optimized chemistry – have been developed. Additionally, turbulence/chemistry coupling modeling remains unresolved in simulations, with three main routes – geometrical, statistical, or reactor-based approaches – available for turbulent combustion modeling. The state-of-the-art in simplified chemistry and turbulent combustion modeling for low-temperature regimes is then focused on capturing MILD regimes, where there is a crucial impact of dilution by burnt gases, heat transfer, and turbulence mixing on the chemical flame structure. Recent advancements enabled by machine learning and deep learning algorithms are also highlighted. Lastly, the article underscores the critical need for data to validate models, emphasizing the importance of scale-bridging experiments.

Expression of Neurotrophic Factors and Their Receptors in the Rat Spinal Trigeminal Nucleus

The spinal trigeminal nucleus as part of the trigeminal sensory nuclear complex is associated with the transmission of discriminative tactile sensations, primarily pain, and temperature, from the orofacial region. It is divided into three parts – caudal, interpolar, and oral subnucleus which process pain and temperature stimulate. Our previous experiments have revealed the presence of certain neurotrophic factors such as the nerve growth factor (NGF), brain-derived neurotrophic factor (BDNF), and neurotrophin-3 (NT-3) in this nucleus. These neurotrophins facilitate neuronal differentiation, survival, and plasticity by signalling through high-affinity transmembrane receptors. By using primary antibodies against NGF, BDNF, NT-3, and glial-derived neurotrophic factor (GDNF), and their corresponding receptors of the tyrosine receptor kinase (Trk) proto-oncogene family and GFRα1, we found immunoreactive cells scattered along the whole length of the nucleus in rats in all three subnuclei. In particular, we observed that the majority of spinal trigeminal neurons were intensely immunostained for all the neurotrophic factors examined and that they were richly endowed with their Trk receptors. Our results also showed that NGF, NT-3, TrkC and GFRα1 expression did not differ between different topographic regions of the nucleus, while BDNF, GDNF, and TrkA expression was highest in the SpVo, and TrkB expression was highest in the SpVi and SpVc. Given that these neurotrophic factors are involved in mechanisms of central sensitization in trigeminal nociceptive pathways, it can be inferred that neurotrophins may contribute to a better understanding of the fundamental mechanisms of orofacial pain.

Preparation and Application of a Novel Liquid Oxygen-Compatible Epoxy Resin of Fluorinated Glycidyl Amine with Low Viscosity

A liquid oxygen-compatible epoxy resin of fluorinated glycidyl amine (TFEPA) with a low viscosity of 260 mPa·s in a wide range of temperatures, from room temperature to 150 °C, was synthesized and used to decrease the viscosity of phosphorus-containing bisphenol F epoxy resins. And the forming process and application performances of this resin system and its composite were investigated. The viscosity of the bisphenol F resin was decreased from 4925 to 749 mPa·s at 45 °C by mixing with 10 wt.% TFEPA, which was enough for the filament winding process. Moreover, the processing temperature and time windows were increased by 73% and 186%, respectively. After crosslinking, the liquid oxygen compatibility was preserved, and its tensile strength, elastic modulus, and breaking elongation at −196 °C were 133.31 MPa, 6.59 GPa, and 2.36%, respectively, which were similar to those without TFEPA. And the flexural strength and modulus were 276.14 MPa and 7.29 GPa, respectively, increasing by 21.73% in strain energy at flexural breaking, indicating an enhanced toughness derived from TFEPA. Based on this resin system, the flexural strength and toughness of its composite at −196 °C were 862.73 MPa and 6.88 MJ/m3, respectively, increasing by 4.46% and 10.79%, respectively.

Microstructural and properties investigations of tantalum-doped tungsten diboride ceramic coatings via HiPIMS and RF magnetron sputtering

In this work, tantalum-doped tungsten boride ceramic coatings were deposited from a single sputtering target with the radio frequency (RF) and high-power impulse magnetron sputtering (HiPIMS) methods. Two-inch torus targets were synthesised from pure elements with the spark plasma sintering (SPS) method with a stoichiometric composition of W1-xTaxB2.5 (x = 0, 0.08, 0.16, 0.24). Films were deposited with RF and HiPIMS power suppliers at process temperatures from RT to 600 °C. The substrate heating and the energy of the ionised material impacting the substrate increase the surface diffusivity of adatoms and are crucial in the deposition process. The results of SEM and XRD investigations clearly show that the addition of tantalum also changes the microstructure of the deposited films. The coatings without tantalum possess a finer microstructure than those with 24% of tantalum. The structure of films is homogeneous along the film thickness and composed mainly of columns with a (0001) preferred orientation. Deposited coatings are composed mainly of P6/mmm α-WB2 structures. The analysis of nanoindentation results allowed us to determine that ceramic coatings obtained with the HiPIMS method possess hardness above 41 GPa and a ratio of hardness to reduced Young modulus above 0.1. The thickness of HiPIMS-deposited films is relatively small: only around 60% of the RF magnetron sputtered coatings even when the average power input was two times higher. However, it has been shown that the RF coatings require heating the substrate above 400 °C to obtain a crystalline structure, while the HiPIMS method allows for a reduction of the substrate temperature to 300 °C.

Amorphous InZnSnO Thin-Film-Transistors Performance Enhancement with Low-Energy Xenon Pulsed-Light Annealing

The electrical characteristics and stability of amorphous indium-zinc-tin oxide (IZTO) thin-film transistors (TFTs) were significantly improved in this study using low-energy Xenon pulsed-light annealing (PLA). In comparison to conventional furnace annealing (FA), PLA treatment significantly reduced the processing temperature and annealing time. Besides, the defect states are obviously reduced from 1.73×1012 cm-2 to 6.53×1011 cm-2 by PLA treatment, resulting in improved device electrical characteristics and enhanced reliability, including improved carrier mobility from 20.08 to 39.61 cm2/V∙s, threshold voltage from 0.82 to 0.24 V, subthreshold swing (S.S.) from 0.54 to 0.24 V/decade, and the ON/OFF current ratio from 2.32×107 to 7.31×108. In addition, the enhanced stability is observed under both positive gate-bias stress (PGBS) of VGS = 30 V and negative gate-bias stress (NGBS) of VGS = –30 V for a stress duration of 3000 s. The threshold voltage shift (ΔVTH) is reduced from 8.31 V to 1.65 V and from –3.93 V to –1.51 V, respectively. This is the first time low-energy PLA was conducted for IZTO TFT performance improvement.

The role of processing temperature for achieving superplastic properties in an Al-3Mg-0.2Sc alloy processed by high-pressure torsion

Experiments were conducted to systematically assess the superplastic properties and the microstructural changes of an Al-3Mg-0.2Sc alloy processed by 10 HPT revolutions at room temperature (RT ≈ 300 K) or at 450 K after subsequent tensile testing at temperatures from 473 to 723 K over a wide range of strain rates. The HPT processing at RT led to the development of elongated grains with an average size of ∼140 nm whereas the grain structures were equiaxed and slightly larger (∼150 nm) after HPT at 450 K. After HPT processing at RT, the Al-Mg-Sc alloy exhibited true superplastic flow at low homologous temperatures and attained a maximum elongation of ∼850 % at 523 K. Nevertheless, the elongations decreased at temperatures T ≥ 623 K and an elongation higher than 400 % was only achieved at 673 K for a strain rate of ε˙ = 4.5 × 10−3 s−1. The material processed by HPT at 450 K displayed superior microstructural stability and substantially higher superplastic ductilities. Elongations of >1100 % were attained at 673 K for strain rates from 3.3 × 10−4 to 1.0 × 10−1 s−1 and a record elongation of ∼1880 % for an HPT-processed metal was achieved at 1.5 × 10−2 s−1 at 673 K. High strain rate superplasticity was also reached for an extended range of temperatures and strain rates. Analysis of the data confirms a stress exponent of ∼2 which is consistent with superplastic flow by grain boundary sliding accommodated by dislocation glide and climb.

Prediction and optimization of wet bulb efficiency in solar energy-based novel evaporative cooling system: Response Surface Method Approach

Abstract The wet bulb efficiency is an essential parameter in performance of Indirect evaporative cooling systems, as it impacts efficiently cool air while minimizing energy usage. This paper focuses on model and optimize multi tubular type wet channel for indirect evaporative cooler system. The optimized wet bulb efficiency based on Box-Behnken experimental design model and response surface method. The methodology included predicting and optimizing input process and working flow parameters of indirect evaporative cooling system to maximize wet bulb efficiency. A quadratic model of response surface method was used to evaluate influence of each factor on wet bulb efficiency, which was validated through analysis of variance results. The study found a maximum WBE of 89.65% under specific conditions, with a relative error of 3.25% between predicted and experimental result. This optimization process, governed by RSM, determined essential parameters for enhancing efficiency of system. These parameters include inlet process temperature of 28°C, working air velocity of 3.5 m/s, relative humidity of 45%, and inlet working air temperature of 24°C. These results demonstrate practical significance of current research, providing useful insights for optimal design and optimization of indirect evaporative cooling systems to fulfil cooling requirements while minimising energy consumption.

Enhanced osmotic dehydration of watermelon rind using honey-sucrose solutions: A study on pre-treatment efficacy and mass transfer kinetics.

This study investigates the osmotic dehydration process of watermelon rind using a solution composed of honey and sucrose. The impact of the ratio of rind-to-solution and temperature on the process is illustrated. Pre-treatments such as blanching, microwaves, and ultrasonication were utilized. Ultrasonication reduces the time needed for osmosis in a sample, resulting in increased fluid loss and solute uptake; therefore, it was selected as the method to investigate the kinetics and modelling of mass transfer. The effective diffusivities for water loss (ranging from 3.02 × 10-5 to 4.21 × 10-4 m2 s-1) and solid gain (ranging from 1.94 × 10-6 to 3.21 × 10-6 m2 s-1) were shown to increase with process variables such as temperature and the rind-to-solution ratio. The activation energy decreased as the process temperature increased, ranging from 3.723 to 0.928 kJ mol-1 for water loss and from 1.733 to 0.903 kJ mol-1 for solid gain, respectively. The sample treated with microwaves exhibited the maximum dehydration coefficient, rendering it appropriate for producing dehydrated products. Five empirical models were utilized, with the power law model (R 2 = 0.983) and the Magee model (R 2 = 0.950) being the most suitable for water loss data and solid gain, respectively.

Entrapment of Amphipathic Drugs in Core-Shell Polymeric Nanoparticles under Batch Conditions─The Role of Control and Solubility Parameters.

The amphipathic bioactive compounds curcumin, resveratrol, and mitomycin C, which have similar solubility parameter component distributions, have been studied for encapsulation under batch conditions into core-shell nanocarriers composed of external hydrophobically functionalized polyelectrolytes and an inner matrix of polyesters or polyester blends: poly(l-lactide), poly(lactide-co-glycolide), and/or poly(ethylene succinate). Our contribution comprises determining the influence of process parameters on the properties and quality of the final products, namely core-shell nanoparticles loaded with appropriate drugs, according to process analysis technologymanagement. The crucial roles of the organic phase dosing rates and process temperatures were carefully investigated. Moreover, a technically feasible method of removing organic solvents from aqueous dispersions─stripping with inert gas─was employed and evaluated via FT-IR studies. The experiments were supported by the calculation and analysis of solubility parameters (δ) and dispersion (δd), polar (δp), and hydrogen bond (δh) components utilizing HSPiP software. The payload locus and sample morphology were studied via atomic force microscopy and X-ray photoelectron spectroscopy analyses with Ar+ sputtering. It was demonstrated that dosing rates of organic phases not exceeding ca. 0.5 mL/min per 1 L of aqueous dispersion of hydrophobically functionalized polyelectrolytes made it possible to obtain core-shell nanoparticles of ca. 100-150 nm with a very narrow polydispersity (PdI < 0.2). The locus of amphipathic payloads in nanocarriers, mostly within the core polymeric structure, was in good agreement with the results of solubility parameter component studies: water-insoluble polyesters with both polar and nonpolar interactions between chains serve as good host materials for amphipathic drugs.

Thermo-Convective Solution Growth of Vertically Aligned Zinc Oxide Nanowire Arrays for Piezoelectric Energy Harvesting

The search for a synthesis method to create longer ZnO NWAs with high-quality vertical alignment, and the investigation of their electrical properties, have become increasingly important. In this study, a hydrothermal method for growing vertically aligned arrays of ZnO nanowires (NWs) using localized heating was utilized. To produce longer NWs, the temperature environment of the growth system was optimized with a novel reaction container that provided improved thermal insulation. At a process temperature above ~90 °C, ZnO NWs reached a length of ~26.8 µm within 24 h, corresponding to a growth rate of 1.1 µm/h, nearly double the rate of 0.6 µm/h observed in traditional chemical bath growth using a glass reactor. The densely grown NWs (~1.9/µm2), with a diameter of ~0.65 µm, exhibited a preferred hexagonal c-axis orientation and were vertically aligned to the (100) silicon (Si) substrate. These NW structures have multiple applications, e.g., in piezotronic strain sensors, gas sensing, and piezoelectric energy harvesting. As proof of concept, a piezoelectric nanogenerator (PENG) was fabricated by embedding the NWs in an S1818 polymer matrix over a 15 mm × 15 mm area. Under repeated impulse-type compressive forces of 0.9 N, a maximum peak output voltage of ~95.9 mV was recorded, which is higher by a factor of four to five than the peak output voltage of 21.6 mV previously obtained with NWs measuring ~1.8 µm in length.

Effect of Sintering Temperature and Hot Cross-Rolling Process on Physical, Mechanical and Microstructural Properties of Al/B4C Composite Made by the Hot Pressing Process

Effect of Sintering Temperature and Hot Cross-Rolling Process on Physical, Mechanical and Microstructural Properties of Al/B4C Composite Made by the Hot Pressing Process