Pressure Force Research Articles

The walking surface influences vertical ground reaction force and centre of pressure data obtained with pressure-sensing insoles

BackgroundGait can be continuously monitored via vertical ground reaction force (VGRF) and centre of pressure (COP) measurement with pressure-sensing insoles. During daily living, a variety of walking surfaces will be encountered, which could affect the collected data. These effects might need to be taken into account when analysing disease- or injury-related gait characteristics to prevent misinterpretation, especially when drawing conclusions from data obtained in clinical populations. We hypothesized characteristic changes in insole-derived VGRF and COP parameters of healthy participants when walking on different surfaces.MethodsParticipants walked on flat indoor surface, flat and inclined outdoor surfaces, as well as on forest, gravel, grass, and sand surfaces while wearing pressure-sensing insoles with 16 pressure sensors each at a recording frequency of 100 Hz. Several gait parameters were extracted from the VGRF and COP data, and were compared between surfaces using repeated measures ANOVA.ResultsThirty participants were included (22 women and 7 men, age 30 ± 12 years, height 172 ± 8 cm, weight 76 ± 23 kg). VGRF and COP data were significantly influenced by the type of surface. The rmANOVA revealed significant within-subject differences between the walking surfaces in all calculated parameters. The largest changes in the VGRF and COP patterns occurred during uphill and downhill walking. Walking on compliant surfaces led to increased gait variability. The highest variability was observed when walking on sand. The change from walking indoors to outdoors, be it on flat, inclined, forest, gravel, grass or sand surfaces, was characterized by a characteristic change in the VGRF stance-phase curve. Based on these characteristic changes, it could be possible to identify whether someone is walking on a slope, as well as on non-compliant or compliant surfaces, while it is difficult to distinguish between different types of compliant surfaces.ConclusionVGRF data are affected by the type of walking surface in healthy adults. Walking on a slope affects VGRF and COP parameters, and in addition, the compliance of the surface increases their variability. When analysing gait data measured via insoles during daily living, we recommend to correct for the surface type to decrease variability.

Deciphering the Evolution of Thermodynamic Properties and their Connection to the Global Kinematics of High-Speed Coronal Mass Ejections Using FRIS Model

Abstract Most earlier studies have been limited to estimating the kinematic evolution of coronal mass ejections (CMEs), and only limited efforts have been made to investigate their thermodynamic evolution. We focus on the interplay of the thermal properties of CMEs with their observed global kinematics. We implement the Flux rope Internal State (FRIS) model to estimate variations in the polytropic index, heating rate per unit mass, temperature, pressure, and various internal forces. The model incorporates inputs of 3D kinematics obtained from the Graduated Cylindrical Shell (GCS) model. In our study, we chose nine fast-speed CMEs from 2010 to 2012. Our investigation elucidates that the selected fast-speed CMEs show a heat-release phase at the beginning, followed by a heat-absorption phase with a near-isothermal state in their later propagation phase. The thermal state transition, from heat release to heat absorption, occurs at around 3(±0.3) to 7(±0.7) R⊙ for different CMEs. We found that the CMEs with higher expansion speeds experience a less pronounced sharp temperature decrease before gaining a near-isothermal state. The differential emission measurement (DEM) analysis findings, using multi-wavelength observation from SDO/AIA, also show a heat release state of CMEs at lower coronal heights. We also find the dominant internal forces influencing CME radial expansion at varying distances from the Sun. Our study shows the need to characterize the internal thermodynamic properties of CMEs better in both observational and modeling studies, offering insights for refining assumptions of a constant value of the polytropic index during the evolution of CMEs.

Viscoelastic liquid flow dynamics in small porous-medium channels under pressure and velocity forces

Viscoelastic liquid flow dynamics in small porous-medium channels under pressure and velocity forces

Driving Forces of the Consumer Price Index During the Crises in the Eurozone: Heterogeneous Panel Approach

This paper examines key driving forces of inflationary pressures, taking into account supply and demand side determinants and actions of policy makers, during the pandemic and geopolitical crises in the Eurozone. Using heterogeneous nonstationary macro-panel models, especially the Mean Group (MG) and Pooled Mean Group (PMG) methods in the period 2020q1–2024q4, it is concluded that the dominant determination of inflationary pressures comes from the supply side. There is a long-run positive equilibrium relationship between the growth of energy prices and the growth of the consumer price index (CPI), and between the index representing supply bottlenecks (SBI) and the growth of CPI, while the relationship with the unemployment rate is insignificant. Also, the existence of a long-run equilibrium between the interest rate and CPI is homogeneous due to the unique monetary policy on a sample, and negative, indicating the efficiency of that policy. However, the speed of adjustment of individual economies is heterogeneous, and in the case of Greece and Ireland, insignificant. The heterogeneous or insignificant response of Eurozone member states, especially related to core-periphery asymmetry, refers to the vulnerability and structural weakness of the Eurozone economies, and the need for deeper integration.

Novel Fluidic Oscillator Evaluation Considering Dimensional Modifications

Although flow mixing and cooling can be greatly enhanced when considering the use of fluidic oscillators (FOs), they are more commonly employed in active flow control (AFC) applications where the injected pulsating flow interacts with the boundary layer, usually in order to delay its separation. In fact, prior to any FO implementation in a given application, it is essential to study the range of frequencies and amplitudes it can generate as a function of the incoming mass flow and its dimensions. This is what is being performed in the present manuscript for a rather novel FO configuration. A numerical study of a standard three-dimensional (3D) FO configuration, and also using a two-dimensional (2D) approach, is initially presented. After comparing the 3D and the 2D results and analyzing the main differences, we modified some of the internal dimensions of the FO in order to evaluate the variation in its dynamic performance. The present results clarify which internal dimensional modifications are more effective in generating larger output frequencies and velocity field variations. Care is taken to analyze the origin of self-sustained oscillations. This paper links, for the first time, the origin of the pressure force oscillations at the feedback channel’s outlet, with the interaction of the mixing chamber central jet and the reverse feedback channel flow at the mixing chamber’s converging walls. A novel equation relating the FO outlet mass flow frequency with the time-averaged FC reverse flow is presented and discussed. In fact, the present study needs to be seen as the continuation of a former one, recently published by authors, where the effects of several Reynolds numbers as well as some different internal dimensions were considered.

Flexibility, Dispersion Property, and Giant Sunlight Absorption of Monolayer MX2 (M = Zr, Hf; X = S, Se) and Related Janus MXY (M = Zr, Hf; X = S, Y = Se)

IVB–VIA transition metal dichalcogenides (TMDs) MX2 (M = Zr, Hf; X = S, Se) and related Janus MXY (M = Zr, Hf; X = S, Y = Se) have garnered significant attention due to their unique optoelectronic properties. To further explore their potential in flexible photonics, their mechanical, band dispersion, and optical dielectric properties using orbital hybrid theory are investigated. The results reveal that the out‐of‐plane linear compression resistance of these materials is considerably lower than their in‐plane resistance, primarily because van der Waals interactions are much weaker compared to ionic bond interactions. This characteristic makes them less susceptible to external pressure and torsional forces, positioning them as promising candidates for flexible optoelectronic devices. Furthermore, the presence of multiple energy bands at the same momentum state suggests a tendency toward metal–insulator transitions. Notably, the materials exhibit a high photon flux, indicating robust photoelectric conversion capabilities, making them suitable for applications in photoelectric transducers. This study not only deepens the understanding of the optoelectronic and mechanical properties of IVB–VIA TMD materials, but also offers theoretical guidance for the development and application of flexible optoelectronic devices based on IVB‐VIA TMDs and related Janus materials.

Research on the Mechanism of Femtosecond Laser Ablation Concave-Convex Microstructure Transformation.

The phenomenon of femtosecond laser ablation of convex structures from the bottom to the top is interesting. In this study, AZ31B magnesium alloy was used as the substrate to analyze the impact of the laser pulse energy and scanning speed on the morphology of concave-convex microstructures. Subsequently, a unified two-dimensional numerical model incorporating solid, liquid, and gas phases was established, and combined with experimental data, the mechanism and formation process of concave-convex transformation in magnesium alloy under laser ablation were revealed. The results indicate that the transition from concave to convex structures is significantly influenced by the laser scanning speed, whereas the laser pulse energy primarily affects the shape and size of the convex structures. During the ablation process, molten material is expelled and gradually accumulates on both sides of the ablation groove under the action of the recoil pressure. During cooling, the molten material at both ends of the groove merges to form protrusions under the combined effects of internal negative pressure, gravity, and Marangoni forces. Moreover, this method of femtosecond laser ablation for generating convex structures deviates from the traditional single-texture approach to concave structures, potentially broadening the application of laser composite processing surfaces.

Friction-Induced Near-Infrared Emission and Its Mechanism.

Triboluminescence (TL) is an optical phenomenon in which light is emitted from the surface of a material when subjected to pressure or shear forces. Due to its potential applications in non-destructive testing, radiation sources, and spectroscopic probes, TL has garnered increasing attention over the past two decades. However, experimental observations in the infrared spectrum remain limited, and its emission mechanism has not yet been fully understood. In this study, significant emission in the near-infrared spectrum was experimentally observed from the tribo-pairs of Cr/YSZ and quartz/YSZ. The results indicate that the Tribo-Induced Near-Infrared Light Emission consists of three peaks, in which the 780 nm peak is related to the electronic transition between the 3d5/2 and 3d3/2 orbitals of Y3+ ions, while the 880 nm and 990 nm peaks can be attributed to hole centers and T-type centers in the intrinsic defects of YSZ, respectively. Additionally, experiments reveal that the Cr/YSZ tribo-pair exhibits a redshift of 11-18 nm at the 780 nm peak compared to the quartz/YSZ tribo-pair. To explain the cause of the redshift phenomenon, X-ray photoelectron spectroscopy and UV-Vis absorption spectroscopy were used to measure the energy level spacing between the 3d5/2 and 3d3/2 orbitals of Y3+ and the bandgap width of YSZ before and after friction, respectively. We found that the bandgap width of the doped YSZ decreases after friction, which is often accompanied by a reduction in the energy level spacing between the 3d5/2 and 3d3/2 orbitals of Y3+. The extent of the reduction in energy level spacing varies with different dopants, leading to the redshift phenomenon.

Under pressure: Care, capacity and organ donation

In this paper, I seek to theorise the concept of pressure in relation to families’ experiences of organ donation during COVID-19. Drawing on Australia-based fieldwork, I follow circuitries of pressure in and beyond interiorities of bodies, biographies and infrastructures of care to ask what happens when pressure builds to such an extent that there is no capacity left in bodies and in institutions. Pressure concentrates in some spaces and bodies more than others revealing uneven flows and restrictions to care. But how might a theorisation of pressure enable care to be imagined otherwise – to circulate differently? Extending recent care scholarship, I explore alternative versions of care enacted by families and clinicians involved in organ donation. This is an expansive and capacious care, which may offer potential to diffuse the force of pressure through radical interdependence.

Analytical relations for fields and currents in magnetic-pulsed «expansion» of tubular conductors of small diameter

Introduction. This work was initiated by the problems of cardiovascular diseases, which are one of the main causes of mortality of the population of our planet. More than ten years ago, in 2012, approximately 3.7 million people died of acute coronary syndrome worldwide. The fight against such pathologies is carried out with the help of so-called stents, the manufacture of which can be carried out by the method of magnetic pulse «expansion» from hollow metal cylinders. The limited production possibilities of magnetic pulse «expansion» were caused by the minimum cross-sectional size of the inductor-instrument, which can be practically manufactured. Other tools are required to perform this operation. Novelty. A system of magnetic-pulse expansion of thin-walled pipes of small diameter with an inductor that excites an azimuthal electromagnetic field in the case of direct current passing through the processing object and in the absence of its connection in an electric circuit with an inductor is proposed. Purpose. The main analytical dependencies for the characteristics of the electromagnetic processes taking place in the inductor systems for the expansion of cylindrical conductive pipes of small diameter when direct passage of current through the processed object and when it is not connected to an electric circuit with an inductor (insulated billet) is derived. Methods. The solution of the boundary value problem with given boundary conditions was carried out by applying Laplace transforms and integrating Maxwell’s equations. Results. Analytical expressions were obtained for the main characteristics of the processes: the intensities of the excited electromagnetic fields and currents in the system depending on the parameters of the studied systems. The analysis of possible technical schemes for solving the given problem indicated the choice of the optimal variant of an effective system of magnetic-pulse «stretching» of thin-walled cylindrical conductors of small diameter. Practical value. Based on the qualitative analysis of the obtained results, recommendations for the practical implementation of the proposed system were formulated. The obtained dependences allow us to give numerical estimates of the effectiveness of excitation of magnetic pressure forces on the object of processing and to choose directions for further improvement of the magnetic pulse technology for solving such problems. References 23, figures 2.

Study of transient pressure and fluctuation characteristics in a centrifugal pump using the delayed detached-eddy simulation method

This study employed OpenFOAM, the delayed detached-eddy simulation (DDES) turbulence model, and structured grids to develop numerical models for three centrifugal pumps with twisted blades. The internal pressure field, velocity field, forces, and fluctuation characteristics of the centrifugal pumps are comprehensively analyzed under various operating conditions. The findings indicate that the pressure is relatively higher in the flow passages near the volute tongue and the outlet within the impeller. Regions of high relative velocity (slip velocity) are mainly found on the suction side of the blades, indicating that the design of the blade suction side affects the fluid outward slip performance. As the flow rate increases, the forces and force fluctuation amplitudes of each pump component also rise. Conversely, as the rotational speed increases, the force on the blades or impeller gradually increases while the fluctuation amplitude decreases. In the stationary domain, the force on the volute gradually decreases while the fluctuation amplitude of this force increases. The shape of the volute tongue influences the rate at which pressure inside the volute is converted to outlet pressure. The power spectral density (PSD) of pressure fluctuations is smallest at the nominal flow rate, displaying a clear and distinct axial frequency pattern without complex low-frequency fluctuations. Under low flow and high-speed conditions, the PSD at the axial frequency is relatively small, whereas the pressure PSD at other low frequencies is relatively large. This indicates instability in the flow under these conditions.

Turbulent flow and wall forces in staggered square cylinder porous media: An LES Analysis

Abstract The Wall-Modeled-Large Eddy Simulation (WMLES) technique was used to analyze turbulent flow in a porous medium composed of a staggered arrangement of square cylinders. The study focused on a porosity range of 0.3 to 0.8 at a pore Reynolds number of 10×103. The research provides novel information on pressure and shear force distributions around the cylinders and time-averaged values of particle drag and fluctuating lift coefficients. Results indicate that the flow physics are mainly driven by an expansion region in front of the central particle and another in the rear, where the flow is contracted and strongly accelerated. In the first region, velocities, turbulence kinetic energy (k), and its dissipation rate (e) are attenuated by a sudden pressure increase, while in the contraction region, the effect is the opposite. As porosity decreases, flow gradients and the overall levels of k, e, and Reynolds stresses become more significant. Turbulent anisotropy increases as porosity decreases below 0.6. Hydrodynamic stresses in the last interval present relatively uniform levels, which is a unique feature that may be considered in designing dedicated engineering devices with controlled stresses.

A Computational Study of Temperature Driven Low Engine Order Forced Response In High Pressure Turbines

Abstract This paper reports the results of computational studies of the effect of combustor exit temperature distortions on Low Engine Order (LEO) forced response of a High Pressure Turbine (HPT). Forced response of this kind occurs at frequencies below the Stator Vane Passing Frequency (SVPF) and can be a major cause of High Cycle Fatigue (HCF) in turbines due to its tendency to excite fundamental modes of vibration. This paper investigates the extent through which temperature distortions act as a forcing stimulus in HPT rotor rows, through measuring unsteady pressure and modal force magnitude recorded from full annulus unsteady simulations of the MT1 stage: a low temperature, unshrouded, HPT rig. Rotor relative incidence angle variations are shown to be the key mechanism through which temperature acts as a forcer in HPT rotor rows, whilst temperature driven forced response is shown to be dependent on the magnitude of the modal content of the upstream temperature waves. These findings are used to build a reduced domain tool for blocked burner forced response prediction, which is shown to be accurate to an RMS error of 2.66%, far beyond the current accepted standard for forcing prediction of this kind.

Experimental Analysis of Cavitation Erosion: Parameter Sensitivity and Testing Protocols

The scientific goal of this study was to investigate the effects of various parameters on cavitation-induced erosion, with the aim to enhance the understanding and assessment of cavitation resistance in hydraulic systems. Cavitation erosion poses significant challenges to the durability and efficiency of hydraulic components, such as those found in hydropower plants and pumping stations. Prompted by the need to improve the reliability of cavitation testing and material assessment, this research conducted a comprehensive sensitivity analysis of a cavitation jet apparatus (CJA). This study employed an experimental platform that consisted of a vertical cylindrical test tank, a submerged nozzle, and an aluminum sample. By examining a range of orifice diameters, this research identified that smaller diameters led to increased erosion intensity, with the most pronounced effects observed at a diameter of 2 mm. Furthermore, various standoff distances (SoDs) were tested, which revealed that shorter distances resulted in greater erosion, with the highest impact noted at an SoD of 5 cm. This study also evaluated different nozzle geometries, where it was found that a 132° conical sharped edges nozzle, combined with an orifice diameter of 2 mm and an SoD of 5 cm, produced the most severe erosion. Conversely, chamfered edges nozzles and a commercial nozzle (MEG2510) with an SoD of 10 cm or greater showed reduced erosion. These results highlight that by standardizing the testing duration to 1200 s, the CJA could reliably assess the cavitation resistance of materials. This study established a clear relationship between increased pressure and higher impact forces, which led to more severe erosion. The findings underscore the effectiveness of the CJA in evaluating material resistance under various cavitation conditions, thus addressing a critical need for reliable cavitation testing tools.

Numerical simulation of open channel basaltic lava flow through topographical bends

In this study, we utilised computational fluid dynamics to investigate the behaviour of open-channel basaltic lava flows navigating bends on shield volcanoes. Our focus was on understanding the relationship between flow velocity, rheology, and bend geometry. Employing a simple Force Balance Model (FBM), which considers the equilibrium between hydrostatic pressure and centrifugal force, we accurately approximated the changes in the height of the lava’s free surface through various bend geometries. Our analysis includes examining the influence of channel depth, width, and bend radius on the flow, revealing that variations in these parameters significantly affect the flow’s vertical displacement. Additionally, the bend sector angle emerged as a critical factor, indicating a minimum angle necessary for the flow to fully develop before exiting the bend.Further, we assessed the applicability of the Shallow Water Equations (SWE) for modelling the inertial displacement of the lava flow in bends, finding a good fit. The study extended to comparing the FBM’s predictions of the tilt angle of the flow’s free surface with the SWE results, showing notable agreement under specific conditions, particularly at a bend angle of 90 degrees. The impact of fluid density was also considered, revealing that density is a contributing factor to the development of the wetted line in the bend, a factor that is not captured by the simple FBM model. Finally, we explored different rheologies akin to natural lava flows, such as viscoplastic flow, and determined that factors like yield stress, consistency index, and power law index have a small impact on the flow behaviour in a steady-state condition within a bend.

A Multichamber Pulsating-Flow Device With Optimized Spatial Shear Stress and Pressure for Endothelial Cell Testing.

Design and analysis are presented for a new device to test the response of endothelial cells to the simultaneous action of cyclic shear stresses and pressure fluctuations. The design consists of four pulsatile-flow chambers connected in series, where shear stress is identical in all four chambers and pressure amplitude decreases in successive chambers. Each flow chamber is bounded above and below by two parallel plates separated by a small gap. The design of the chamber planform must ensure that cells within the testing region experience spatially uniform time-periodic shear stress. For conditions typically encountered in applications, the viscous unsteady flow exhibits order-unity values of the associated Womersley number. The corresponding solution to the unsteady lubrication problem, with general nonsinusoidal flowrate, is formulated in terms of a stream function satisfying Laplace's equation, which can be integrated numerically to determine the spatial distribution of shear stresses for chambers of general planform. The results are used to optimize the design of a device with a hexagonal planform. Accompanying experiments using particle tracking velocimetry (PTV) in a fabricated chamber were conducted to validate theoretical predictions. Pressure readings indicate that intrachamber pressure variations associated with viscous pressure losses and acoustic fluctuations are relatively small, so that all cells in a given testing region experience nearly equal pressure forces.

Study on the Susceptibility of Steel Arches with Letting Pressure Nodes Based on Incremental Dynamic Analysis

When soft rock tunnels pass through fractured fault zones, they are particularly susceptible to extrusion and large-scale deformations, especially during seismic events. To address these challenges, this study introduces an innovative yield-support steel arch design featuring a circumferential letting pressure node at its core. This design delivers incremental support resistance within the deformation zone and a susceptibility curve is applied to evaluate the damage probability of the steel arch with a letting pressure node under seismic loading conditions. Measurements of the surrounding rock pressure and structural forces on the steel arch with the letting pressure node were conducted at the Baoshan Jewel Mountain Tunnel in China. The field experiment results revealed a 23% reduction in the surrounding rock pressure and an 11% decrease in the internal forces of the support structure. These findings demonstrate the successful application of the letting pressure node-supported steel arch in mitigating large deformations in soft rock environments. Additionally, using finite element software ANSYS 2022, a seismic time-history analysis was conducted, employing the relative deformation rate of the letting pressure node steel arch as the damage index and the peak ground acceleration (PGA) as the strength parameter to generate the incremental dynamic analysis (IDA) curve. According to the susceptibility curve derived from the incremental dynamic analysis, at the design ground motion level of 8 degrees, the letting pressure node steel arch has a 94% probability of exceeding its normal service life limit and experiencing damage. The findings of this study offer a novel approach to addressing large deformations in soft rock tunnels. The proposed susceptibility curves for steel arches with letting pressure nodes provide a robust foundation for predicting the damage probability of yielding support structures under seismic conditions.

Interaction of a self-expandable stent with the arterial wall in the presence of hypocellular and calcified plaques.

Self-expandable stents manufactured from nitinol alloys are commonly utilized alongside traditional balloon-expandable stents to provide scaffolding to stenosed arteries. However, a significant limitation hampering stent efficacy is restenosis, triggered by neointimal hyperplasia and resulting in the loss of gain in lumen size, post-intervention. In this study, a nonlinear finite element model was developed to simulate stent crimping and expansion and its interaction with the surrounding vessel in the presence of a plaque. The main aim was to determine contact pressures and forces induced at the interface between an artery wall with hypocellular and calcified plaques and an expanded stent. The results demonstrated the drawbacks of plaque calcification, which triggered a sharp contact pressure and radial force surge at the interface as well as a significant rise in von Mises stress within the vessel, potentially leading to rupture and restenosis. A regression line was then established to relate hypocellular and calcified plaques. The adjusted coefficient of determination indicated a good correlation between contact pressures for calcified and hypocellular plaque models. Regarding the directionality of wall properties, contact pressure and force observations were not significantly different between isotropic and anisotropic arteries. Moreover, variations in friction coefficients did not substantially affect the interfacial contact pressures.

Verification of validity of the electrodynamic model of ball lightning

The stability of ball lightning is analyzed. According to the electrodynamic model, the ball lightning consists of an energy core in the form of an ensemble of dynamic electric capacitors located inside a spherical shell of water. The dynamic capacitor consists of electrons and protons rotating in closed orbits. The shell tends to stretch under the force Fcf, which is, proportional to the kinetic energy of protons Ek, and the force Fel, proportional to the square of the uncompensated electric charge of the core Q2. The shell is compressed by the force Fsh proportional to its thickness a and the charge Q, as well as the atmospheric pressure force Pa. It is shown that, provided that the radius R of ball lightning can change only due to the work of internal forces, its size remains unchanged. The stability of the size of ball lightning is maintained under the balance of the rate of loss of its energy reserve Ek and the charge Q. If this balance is disturbed, an explosion of ball lightning or its collapse may occur. The relationship between the main parameters of ball lightning is considered: its energy Ek, charge Q, shell thickness a and shell radius R. The conditions for accumulation of maximum energy at a minimum shell thickness are found. The results of calculating the parameters of ball lightning with energy of 10-2300 MJ are compared with the parameters of observed high-energy ball lightning. It is shown that these data are in good agreement with each other.

Coupling of tribovoltaic effect and tribo-electrostatic effect at dynamic semiconductor heterojunction interfaces

Tribovoltaic effect at the dynamic semiconductor interface is of great fundamental and practical importance for developing a variety of functional devices; yet, it can be coupled with a series of different physical effects, such as the contact-electrification induced electrostatic effect and mechanical wearing effect, and the coupling mechanisms are still remained to be elucidated. Herein, we investigated the coupling between tribovoltaic and tribo-electrostatic effects at the dynamic heterojunctions of two wide-bandgap semiconductors: zinc oxide (ZnO) and gallium nitride (GaN). It is found that, in the contact-separation mode, the direct-current outputs from tribovoltaic effect can be clearly distinguished from the alternating-current outputs from tribo-electrostatic effect. Then, humidity, external load resistance and pressure force are found to reveal the coupling characteristics of these two effects, that tribovoltaic outputs are less affected by humidity, show smaller matched impedance and are more sensitive to high pressure force, diverging from the tribo-electrostatic outputs. Lastly, we demonstrate that the mechanical wearing effect can be inhibited in contact-separation mode, achieving long-term stability over 50,000 cycles. Therefore, this work provides insights to the mechanism of tribovoltaic effects and practical guidance for high-performances tribovoltaic devices.