Block Copolymer Precursors Research Articles

Synthesis of Metallic and Metal Oxide Nanoparticles Using Homopolymers as Solid Templates: Luminescent Properties of the Eu+3 Nanoparticle Products

Starting from poly(4-vinylpyridine) ((P4VP)n), poly(2-vinylpyridine) ((P2VP)n), and [N=P(O2CH2CF3)]m-b-P2VP20 block copolymers, a series of metal-containing homopolymers, (P4VP)n⊕MXm, (P2VP)n⊕MXm, and [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm MXm = PtCl2, ZnCl2, and Eu(NO3)3, have been successfully prepared by using a direct and simple solution methodology. Solid-state pyrolysis of the prepared metal-containing polymeric precursors led to the formation of a variety of different metallic and metal oxide nanoparticles (Pt, ZnO, Eu2O3, and EuPO4) depending on the composition and nature of the polymeric template precursor. Thus, whereas Eu2O3 nanostructures were obtained from europium-containing homopolymers ((P4VP)n⊕MXm and (P2VP)n⊕MXm), EuPO4 nanostructures were achieved using phosphorus-containing block copolymer precursors, [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm with MXm = Eu(NO3)3. Importantly, and although both Eu2O3 and EuPO4 nanostructures exhibited a strong luminescence emission, these were strongly influenced by the nature and composition of the macromolecular metal-containing polymer template. Thus, for P2VP europium-containing homopolymers ((P4VP)n⊕MXm and (P2VP)n⊕MXm), the highest emission intensity corresponded to the lowest-molecular-weight homopolymer template, [P4VP(Eu(NO3)3]6000, whereas the opposite behavior was observed when block copolymer precursors, [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm MXm= Eu(NO3)3, were used (highest emission intensity corresponded to [N=P(O2CH2CF3)]100-b-[P2VP(Eu(NO3)3)x]20). The intensity ratio of the emission transitions: 5D0 → 7F2/5D0 → 7F1, suggested a different symmetry around the Eu3+ ions depending on the nature of the polymeric precursor, which also influenced the sizes of the prepared Pt°, ZnO, Eu2O3, and EuPO4 nanostructures.

Polymerization Induced Microphase Separation for the Fabrication of Nanostructured Materials.

Polymerization induced microphase separation (PIMS) is a strategy used to develop unique nanostructures with highly useful morphologies through the microphase separation of emergent block copolymers during polymerization. In this process, nanostructures are formed with at least two chemically independent domains, where at least one domain is composed of a robust crosslinked polymer. Crucially, this synthetically simple method is readily used to develop nanostructured materials with the highly coveted co-continuous morphology, which can also be converted into mesoporous materials by selective etching of one domain. As PIMS exploits a block copolymer microphase separation mechanism, the size of each domain can be tightly controlled by modifying the size of block copolymer precursors, thus providing unparalleled control over nanostructure and resultant mesopore sizes. Since its inception 11 years ago, PIMS has been used to develop a vast inventory of advanced materials for an extensive range of applications including biomedical devices, ion exchange membranes, lithium-ion batteries, catalysis, 3D printing, and fluorescence-based sensors, among many others. In this review, we provide a comprehensive overview of the PIMS process, summarize latest developments in PIMS chemistry, and discuss its utility in a wide variety of relevant applications.

Polymerization Induced Microphase Separation for the Fabrication of Nanostructured Materials

AbstractPolymerization induced microphase separation (PIMS) is a strategy used to develop unique nanostructures with highly useful morphologies through the microphase separation of emergent block copolymers during polymerization. In this process, nanostructures are formed with at least two chemically independent domains, where at least one domain is composed of a robust crosslinked polymer. Crucially, this synthetically simple method is readily used to develop nanostructured materials with the highly coveted co‐continuous morphology, which can also be converted into mesoporous materials by selective etching of one domain. As PIMS exploits a block copolymer microphase separation mechanism, the size of each domain can be tightly controlled by modifying the size of block copolymer precursors, thus providing unparalleled control over nanostructure and resultant mesopore sizes. Since its inception 11 years ago, PIMS has been used to develop a vast inventory of advanced materials for an extensive range of applications including biomedical devices, ion exchange membranes, lithium‐ion batteries, catalysis, 3D printing, and fluorescence‐based sensors, among many others. In this review, we provide a comprehensive overview of the PIMS process, summarize latest developments in PIMS chemistry, and discuss its utility in a wide variety of relevant applications.

AIE-Active, Stimuli-Responsive Fluorescent 2D Block Copolymer Nanoplatelets Based on Corona Chain Compression.

Aggregation-induced emission (AIE) represents a powerful tool in nanoscience as a result of enhanced luminescence in the condensed state. Although AIEgenic materials have been utilized in a wide range of applications, well-defined self-assembled nanoparticles with tailorable and uniform dimensions and morphology remain challenging to access. Herein, we use the seeded growth, living crystallization-driven self-assembly (CDSA) method to prepare size-tunable and uniform AIE-active 2D nanoplatelets from amphiphilic block copolymer (BCP) precursors with a crystallizable core-forming block and a corona-forming block to which tetraphenylethene (TPE) groups were covalently grafted as AIE-active pendants. The nanoplatelets were formed as a result of a solvophobicity-induced 1D to 2D morphology preference change, which accompanied the seeded growth of a BCP with a quaternized corona-forming block bearing the TPE luminogen. The 2D nanoplatelets exhibited a solvent-responsive fluorescent emission, and examples with coronas containing homogeneously distributed AIE-active TPE groups and Hg(II)-capturing thymine units exhibited excellent performance as proof-of-concept "turn-on" sensors for Hg(II) detection with a rapid response, high selectivity, and a low detection limit (5-125 × 10-9 M, i.e., 1-25 ppb). The fluorescence intensity was found to be nonlinear with respect to analyte concentration and to increase with the area of the nanoplatelet. This behavior is consistent with a cooperative mechanism based on changes in the steric compression of the corona chains, which gives rise to a restriction of the intramolecular motion (RIM) effect.

Designing Anion-Exchange Ionomers with Oriented Nanoscale Phase Separation at a Silver Interface

Performance of polymer electrolyte-based energy systems is significantly impacted by transport within the electrode catalyst layer, where ionomer thin films coat catalyst particles. Proton exchange ionomer thin films have been thoroughly characterized, but few studies have critically examined anion-exchange ionomer (AEI) thin films. Further, none have reported nanoscale phase separation for hydrocarbon AEIs, which is critical to mitigate transport resistances. In this work, a set of hydrocarbon-based AEIs with nanoscale phase separation are developed from tunable block copolymer systems composed of polyisoprene (PIp) and polychloromethylstyrene (PCMS). The effect of the PIp/PCMS ratio, architecture, and thickness on the thin-film morphology of the neutral block copolymer precursors on silicon and silver substrates is investigated using grazing-incidence small-angle X-ray scattering (GISAXS) and atomic force microscopy (AFM). AEIs are prepared by quaternizing with trimethylamine or methylpiperidine and their cation-dependent morphology is characterized at 60 °C and 95% RH. A perpendicularly aligned morphology is observed on silver, while no phase separation is observed on silicon, indicating that silver–polymer interfacial interactions drive phase separation. After quaternization, dipole–dipole interactions induce some disorder, but nanoscale phase separation is still maintained. GISAXS patterns are modeled using a Unified Fit approach to understand water uptake and swelling, and recommendations for AEI design are presented.

Fast and efficient single step liquid chromatography separation of parent homopolymers from block copolymers

The modified layout of the barrier method called liquid chromatography under limiting conditions of enthalpic interactions is presented. It enables automated quantitative separation of blends of synthetic polymers, for example the single step discrimination of both parent homopolymers from the block copolymers. Moreover, this method enables the estimation of molar mass and molar mass distribution of the block copolymer precursor. Adjacent large sequences of mobile phase of different composition are applied as barriers. They are created by a computer controlled pair of pumping systems in the form of longitudinal profiles along the column. The home synthesized block copolymers polystyrene-block-poly(2-vinylpyridine) served as model examples of the method application. The adsorption retention mechanism was exploited using mesoporous bare silica gel column packing. Series of block copolymers of similar composition can be quickly handled with the method to optimize their synthesis.

Synthesis of carboxylic acid-functionalized polymethacrylate-b-polystyrene as an Ag ion-loadable block copolymer thin film template

We report the synthesis of thiopropionic acid-functionalized polymethacrylate-b-polystyrene (PMATA-b-PS) as a template for patterning Ag nanoarrays. Reversible addition-fragmentation chain transfer (RAFT) polymerization of silyl-protected propagyl methacrylate followed by chain extension with styrene produced a block copolymer precursor. Deprotection of the trimethylsilyl group and subsequent thiol-yne reaction afforded the target, PMATA-b-PS. While the entire series of the precursor was in the disordered phase, microphase separated morphologies were identified from PMATA-b-PS, indicating an increased interaction parameter (χ) as a result of introducing the acid groups. As a preliminary result, we show that an Ag nanoparticle array can be fabricated by selectively associating Ag+ ions to the PMATA cylinders in the thin film of PMATA-b-PS and removing the organic polymer layer by oxygen plasma treatment.

Effects of Hydrophobic Modifications on the Solution Self-Assembly of P(DMAEMA-co-QDMAEMA)-b-POEGMA Random Diblock Copolymers.

In this work, the synthesis and the aqueous solution self-assembly behavior of novel partially hydrophobically modified poly(2-(dimethylamino) ethyl methacrylate)-b-poly(oligo(ethylelene glycol) methyl ether methacrylatetabel) pH and temperature responsive random diblock copolymers (P(DMAEMA-co-Q6/12DMAEMA)-b-POEGMA), are reported. The chemical modifications were accomplished via quaternization with 1-iodohexane (Q6) and 1-iodododecane (Q12) and confirmed by 1H-NMR spectroscopy. The successful synthesis of PDMAEMA-b-POEGMA precursor block copolymers was conducted by RAFT polymerization. The partial chemical modification of the diblocks resulted in the permanent attachment of long alkyl chains on the amine groups of the PDMAEMA block and the presence of tertiary and quaternary amines randomly distributed within the PDMAEMA block. Light scattering techniques confirmed that the increased hydrophobic character results in the formation of nanoaggregates of high mass and tunable pH and temperature response. The characteristics of the aggregates are also affected by the aqueous solution preparation protocol, the nature of the quaternizing agent and the quaternization degree. The incorporation of long alkyl chains allowed the encapsulation of indomethacin within the amphiphilic diblock copolymer aggregates. Nanostructures of increased size were detected due to the encapsulation of indomethacin into the interior of the hydrophobic domains. Drug release studies demonstrated that almost 50% of the encapsulated drug can be released on demand by aid of ultrasonication.

Transient Multivalent Nanobody Targeting to CD206-Expressing Cells via PH-Degradable Nanogels.

To target nanomedicines to specific cells, especially of the immune system, nanobodies can be considered as an attractive tool, as they lack the Fc part as compared to traditional antibodies and, thus, prevent unfavorable Fc-receptor mediated mistargeting. For that purpose, we have site-specifically conjugated CD206/MMR-targeting nanobodies to three types of dye-labeled nanogel derivatives: non-degradable nanogels, acid-degradable nanogels (with ketal crosslinks), and single polymer chains (also obtained after nanogel degradation). All of them can be obtained from the same reactive ester precursor block copolymer. After incubation with naïve or MMR-expressing Chinese hamster ovary (CHO) cells, a nanobody mediated targeting and uptake could be confirmed for the nanobody-modified nanocarriers. Thereby, the intact nanogels that display nanobodies on their surface in a multivalent way showed a much stronger binding and uptake compared to the soluble polymers. Based on their acidic pH-responsive degradation potential, ketal crosslinked nanogels are capable of mediating a transient targeting that gets diminished upon unfolding into single polymer chains after endosomal acidification. Such control over particle integrity and targeting performance can be considered as highly attractive for safe and controllable immunodrug delivery purposes.

Fabrication of an Inverse Size-Selective Membrane Using an Electrospun Nanofiber Mat as a Template.

Size-selective membranes have applications in water purification and other areas. Although many methods have been developed for the fabrication of nanoporous membranes, each method has its limitations. For example, thin films containing uniform nanochannels can be prepared from block copolymer precursors. However, block copolymers are expensive. The electrospinning of a polymer solution can yield long nanofibers that fold into mats and the diameters of these fibers can be tuned from nanometers to micrometers. Infusing another polymer into the voids between these fibers and subsequently removing the nanofiber template should yield an inverse porous membrane, complementary in pore structure to the original nanofiber mat membrane. In this paper, we report on the fabrication of these membranes. We discovered that the flux across such membranes increased by thermally annealing the nanofiber mats under pressure before the infusion of the second polymer and by etching the surfaces of the final membrane with plasma to expose the encapsulated nanochannels. We further discovered that the size of the pores formed at the junction of the fused nanofibers and, eventually, the nanotubes governed the size selectivity of the final membrane. The pore size at the junctions increased by increasing the thermal annealing temperature and, thus, the extent of fiber fusion. The developed methodology is general and should be useful for the fabrication of nanoporous membranes from different materials possessing pore diameters that are governed by the diameter of the templating nanofibers and the extent of their fusion.

Preparation of Nitrogen-Doped Mesoporous Carbon for the Efficient Removal of Bilirubin in Hemoperfusion.

The development of bilirubin adsorbent with high selectivity, brilliant adsorption ability, and biocompatibility is still a considerable challenge. In this study, a copolymer-templated nitrogen-doped mesoporous carbon (CTNC) has been prepared via a simple carbonization procedure of well-defined polyacrylonitrile-block-poly(n-butyl acrylate) (PAN-b-PBA) block copolymer precursors. The structure and morphology were characterized by transmission electron microsphere (TEM), adsorption-desorption isotherms, and X-ray photoelectron spectroscopy (XPS). Owing to its high specific area, hierarchical open-porous structure, and the introduction of nitrogen atoms in graphitic sp2 network, the adsorbent CTNC exhibited high removal efficiency toward bilirubin and bile acid from human plasma. The removal rate of bilirubin was more than 50.7% with a minimal loss of albumin. Meanwhile, exceeding 95% of bile acid was eliminated. The effect of albumin on the adsorption kinetic of bilirubin was identified. The result indicated that the adsorption rate of BSA-bonded bilirubin experienced a decline than that of free bilirubin, but the adsorption capacity was still up to 39.8 mg/g within 2 h. Moreover, the effect of porosity and nitrogen contents on bilirubin adsorption ability and blood compatibility were systematically investigated. The material with lower nitrogen content showed only a negligible hemolysis activity. Therefore, the nitrogen-doped mesoporous carbon developed in this work has potential application in blood purification for the efficient removal of bilirubin.

α-Mannosyl-Functionalized Cationic Nanohydrogel Particles for Targeted Gene Knockdown in Immunosuppressive Macrophages.

Immunosuppressive M2 macrophages govern the immunophathogenic micromilieu in many severe diseases including cancer or fibrosis, thus, their re-polarization through RNA interference is a promising concept to support combinatorial therapies. For targeted siRNA delivery, however, safe and stable carriers are required that manage cell specific transport to M2 macrophages. Here, siRNA-loaded cationic nanogels are reported with α-mannosyl decorated surfaces that target and modify M2 macrophages selectively. Via amphiphilic precursor block copolymers bearing one single α-mannosyl moiety at their chain end mannosylated cationic nanohydrogel particles (ManNP) were obtained of 20 nm diameter determined by dynamic light scattering and cryogenic electron transmission microscopy. α-Mannosyl surface modification is confirmed by agglutination with concanavalin A. SiRNA-loaded ManNP preferentially targets the overexpressed mannose receptor CD206 on M2 macrophages, as shown by in vitro cell uptake studies in M2 polarized primary macrophages. This specificity is confirmed, since ManNP uptake could be reduced by blocking of CD206 with mannan. Effective ManNP-guided siRNA delivery is confirmed by sequence-specific gene knockdown of CSF-1R in M2-type macrophages exclusively, while the expression levels in M1-polarized macrophages is not affected. In conclusion, α-mannosyl-functionalized ManNPs are promising universal siRNA carriers for targeted immunomodulatory treatment of immunosuppressive macrophages.

Ultrathin nanoporous membrane fabrication based on block copolymer micelles

As researchers can control the nanostructure of the nanoporous membrane based on block copolymer precursors, it is considered to be an ideal device for separation and purification. However, the challenge still remains to make ultrathin, economic, nanopore sized and charged isoporous membranes without post-treatment. Hence, a simple, energy saving and sacrificial layer free technique was adopted to bridge the gap between the uniformly spread PS-b-PAA nanospheres and the ultrathin, negatively charged nanoporous membrane. The flux of the membrane is as high as 350 L m−2 h−1 bar−1, while the effective pore size is only ca. 8 nm. It can separate not only the nanoparticles based on their size differences, but can also separate similarly sized proteins based on the charge differences efficiently. Moreover, nanofibers and lamellae formed nanoporous membranes have now been fabricated. The effective pore size can be customized, and can even be smaller than 1.5 nm for the lamellae formed membrane.

Preparation, characterization, and in vitro activity evaluation of triblock copolymer-based polymersomes for drugs delivery

Polymersomes are polymer-based vesicles that form upon hydration of amphiphilic block copolymers and display high stability and durability, due to their mechanical and physical properties. They have hydrophilic reservoirs as well as thick hydrophobic membranes; allowing to encapsulate both water-soluble bioactive agent and hydrophobic drugs. In this study, poly ethylene glycol (PEG3350 and PEG6000) were used as hydrophilic part and poly(vinyl benzoate) (PVBz) as hydrophobic block to synthesize amphiphilic triblock copolymers (PVBz-b-PEG-b-PVBz). Different proportions of hydrophilic/hydrophobic part were assayed in order to obtain polymersomes by solvent injection method. For the synthesis of the copolymers, the initial block of PEG was derived to obtain a macroinitiator through a xanthate functional group (PEGX3 or PEGX6) and the polymerization of vinyl benzoate was carried out through reversible addition-fragmentation chain transfer polymerization (RAFT). The structure of PEGX and copolymers was confirmed by Infrared, 1H-NMR and UV-Vis spectrometry, while the average molecular weight (Mw) and polydispersity index (PI) were determined by size exclusion chromatography (SEC). The structures adopted by the copolymers in aqueous solution by self-assembly were investigated using transmission electron microscopy (TEM), dynamic light scattering (DLS) and small-angle X-ray scattering (SAXS). Both techniques confirm that polymersomes were obtained for a fraction of hydrophilic block (f) ≈ 35 ± 10%, with a diameter of 38.3 ± 0.3 nm or 22.5 ± 0.7 nm, as determined by TEM and according to the M w of the precursor block copolymer. In addition, we analyzed the possible cytotoxicity in view of its potential application as biomedical nanocarrier. The results suggest that polymersomes seem not induce cytotoxicity during the periods of time tested.

One-pot “grafting-from” synthesis of amphiphilic bottlebrush block copolymers containing PLA and PVP side chains via tandem ROP and RAFT polymerization

A one-pot “grafting-from” strategy is presented to prepare AB- and ABA-type bottlebrush block copolymers (BBCPs). Precursor block copolymers with pendant dithiocarbamate and hydroxyl groups were synthesized as the macroinitators. Polylactide (PLA) and poly(N-vinylpyrrolidone) (PVP) side chains were grafted by ring-opening polymerization (ROP) and reversible addition-fragmentation chain-transfer (RAFT) polymerization in one pot, respectively. Molecular weight control was achieved as evidenced by gel permeation chromatography (GPC) and 1H nuclear magnetic resonance (1H NMR). The length of side chains in each block (DP from 8 to 113) could be facilely tuned by polymerization conditions such as the reaction time and the feed ratio of monomer to initiator, leading to various molecular morphologies observed by atomic force microscopy (AFM). This synthetic strategy is flexible and adaptable, allowing convenient access to customized macromolecular architecture.

Cationic Nanohydrogel Particles for Therapeutic Oligonucleotide Delivery.

Short pharmaceutical active oligonucleotides such as small interfering RNA (siRNA) or cytidine-phosphate-guanosine (CpG) are considered as powerful therapeutic alternatives, especially to medicate hard-to-treat diseases (e.g., liver fibrosis or cancer). Unfortunately, these molecules are equipped with poor pharmacokinetic properties that prevent them from translation. Well-defined nanosized carriers can provide opportunities to optimize their delivery and guide them to their site of action. Among several concepts, this Feature Article focuses on cationic nanohydrogel particles as a universal delivery system for small anionic molecules including siRNA and CpG. Cationic nanohydrogels are derived from preaggregated precursor block copolymers, which are further cross-linked to obtain well-defined nanoparticles of tunable sizes and with (degradable) cationic cores. Novel opportunities for oligonucleotide delivery in vitro and in vivo with respect to liver fibrosis therapies will be highlighted as well as perspectives toward modulating the immune system. In general, the approach of covalently stabilized cationic carrier systems can contribute to find advanced oligonucleotide therapeutics.

Nanoporous Films with Sub-10 nm in Pore Size from Acid-Cleavable Block Copolymers.

Nanoporous thin films with pore size of sub-10 nm are fabricated using an acid-cleavable block copolymer (BCP), a benzoic imine junction between poly(ethylene oxide) (PEO) and poly(methacrylate) (PMAAz) bearing an azobenzene side chain (denoted as PEO-bei-PMAAz) as the precursor. After a thermal annealing, the block copolymers are self-assembled to form highly ordered PEO cylinders within a PMAAz matrix normal to the film, even in the case of low BCP molecular weight due to the existing of the liquid crystalline (LC) azobenzene rigid segment. Thus, PMAAz thin films with pore size of ≈7 nm and density of ≈1012 cm-2 are obtained after removal of the PEO minor phase by breaking the benzoic imine junction under mild acidic conditions. This work enriches the nanoporous polymer films from BCP precursors and introduces the LC property as a functionality which can further enhance the mechanical properties of the films and broaden their applications.

Formation of hierarchical mesoporous silicon carbide from self-assembled block copolymer micelles

We report a novel technique for synthesizing hierarchical mesoporous non-oxide SiC ceramic from a block copolymer precursor. The block copolymers self-assemble into nano-scaled micelles with a core-shell structure in toluene and the subsequent pyrolysis converts the aggregation of the micelles into SiC. The resultant SiC shows hierarchical mesoporous structure and has potential applications in catalysis, solar cells, separation, and purification processes. The technique is likely applicable in other non-oxide material systems.

A New Approach for the Synthesis of pH‐Responsive Cross‐Linked Micelles from a Poly(glycidyl methacrylate)‐Based Functional Copolymer

An amphiphilic poly(ethylene glycol)methyl ether‐block‐poly(glycidyl methacrylate) (MPEG‐b‐PGMA) diblock copolymer is first synthesized via atom transfer radical polymerization. Epoxy groups of this precursor block copolymer are converted to hydroxyl and tertiary amine residues by reacting with diethyl amine over a ring‐opening reaction. The resulting diblock copolymer is poly(ethylene glycol)methyl ether‐block‐poly(3‐diethylamino‐2‐hydroxypropyl methacrylate) (MPEG‐b‐PDEAHPMA). Micellar solution of this diblock copolymer is prepared at pH 12.0 in aqueous media. At high pH (12.0), core– shell micelles are formed with PDEAHPMA‐core and MPEG‐shell. PDEAHPMA blocks have both hydroxyl and tertiary amine groups that provide reactivity against divinyl sulfone (DVS) and a response to solution pH, respectively. Cross‐linking of hydroxyl groups of PDEAHPMA chains in the micelle core is successfully achieved by adding DVS. At pH 2.0, the DEAHPMA‐core of core cross‐linked (CCL) micelles becomes protonated and hence swelling is observed. The effect of varying the DVS concentrations is also studied. The micelle formation of diblock copolymer and its response to solution pH are investigated by using surface tensiometer, 1H NMR spectroscopy, and dynamic light scattering (DLS) techniques. CCL micellar structure and its response to solution conditions are investigated with transmission electron microscopy and DLS studies, respectively. image

Biomimetic Nanofluidic Diode Composed of Dual Amphoteric Channels Maintains Rectification Direction over a Wide pH Range.

pH-gated ion channels in cell membranes play important roles in the cell's physiological activities. Many artificial nanochannels have been fabricated to mimic the natural phenomenon of pH-gated ion transport. However, these nanochannels show pH sensitivity only within certain pH ranges. Wide-range pH sensitivity has not yet been achieved. Herein, for the first time, we provide a versatile strategy to increase the pH-sensitive range by using dual amphoteric nanochannels. In particular, amphoteric polymeric nanochannels with carboxyl groups derived from a block copolymer (BCP) precursor and nanochannels with hydroxyl groups made from anodic alumina oxide (AAO) were used. Due to a synergistic effect, the hybrid nanochannels exhibit nanofluidic diode properties with single rectification direction over a wide pH range. The novel strategy presented here is a scalable, low-cost, and robust alternative for the construction of large-area membranes for nanofluidic applications, such as the separation of biomolecules.