Power System Load Research Articles

An Analysis of Case Study Utilizing Distributed Power Flow Controllers Which Improves and Mitigates Power Quality

Abstract—Providing high-quality electrical power should be taken into consideration in light of the rising demand for electricity and the rise in non-linear loads in power systems. This research examines power quality concerns related to voltage sag and swell and uses a distributed power flow controller (DPFC) to reduce voltage deviation and enhance power quality. A novel FACTS device, the DPFC shares structural similarities with the unified power flow controller (UPFC). Despite UPFC, DPFC separates the three-phase series converter into many single-phase series dispersed converters via the line and removes the common dc-link between the shunt and series converters. A DPFC located in a single-machine infinite bus power system with two parallel transmission lines is included in the case study. The MATLAB/Simulink environment was to model the system. The simulation findings that are shown confirm that DPFC may raise power quality.

Optimization of emergency frequency control strategy for power systems considering both source and load uncertainties

With the increasing integration of renewable energy sources and the presence of numerous controllable loads such as electric vehicles and energy storage in the modern power system, higher nonlinearities and uncertainty both sources and loads are introduced. These factors pose challenges in achieving fast and accurate emergency frequency control. Therefore, this paper addresses the issue of dual source-load uncertainties in power system and presents an optimization strategy based on the Soft Actor Critic (SAC) algorithm that involves the participation of controllable loads in emergency frequency control. Firstly, the spatio-temporal uncertainties of wind farm power output on power supply side and power demand on the load side are described using Weibull and normal probability distributions, respectively. Secondly, an improved Markov Decision Process (MDP) model for emergency frequency control is established, which considers the characteristics of the dual source-load uncertainties. Finally, an optimization of the SAC algorithm is conducted based on Deep Reinforcement Learning (DRL), aiming to achieve rapid system frequency recovery and minimize the cost of removing controllable loads. The presented approach in the paper enhances the emergency frequency control strategy for uncertain power systems and effectively addresses the issue of source-load uncertainty compounded by fault power shortages.

Fusion Forecasting Algorithm for Short-Term Load in Power System

Fusion Forecasting Algorithm for Short-Term Load in Power System

Research on power metering method for nonlinear loads in power system based on improved S-transform

Abstract Traditional power metering algorithms are no longer suitable for new power systems to address the issue of distorted voltage and current waveforms caused by a growing number of nonlinear loads in modern power systems. The paper proposes a power-metering algorithm based on an Improved Stockwell Transform (IST). Based on the Stockwell transform, several parameters that can control the Gaussian window are introduced to improve the flexibility of the Gaussian window. Additionally, the inequality constraint based on the energy concentration measure is used to optimally select the best window parameters, enhancing the time–frequency domain analysis capability of the IST. The study uses IST to decompose and reconstruct the voltage and current fundamental characteristic signals and distortion characteristic signals in the power system. This provides good time resolution at low frequencies and good frequency-domain resolution at high frequencies. Power metering based on unsteady voltage and current is achieved by calculating the resulting fundamental and harmonic powers, respectively. The simulation results demonstrate that the IST-based power metering method has a higher level of accuracy than the existing metering methods.

Reliability-constrained configuration optimization for integrated power and natural gas energy systems: A stochastic approach

With the escalating dependence on electricity and natural gas infrastructure, ensuring both reliability and economic efficiency becomes paramount. It necessitates reliability centric measures to mitigate disruptions that could cascade between these interconnected systems. To address this challenges, this paper introduces a reliability-constrained two-stage stochastic model to optimize power-to-gas (P2 G) and gas-to-power (G2P) unit placement and sizing, aiming to enhance the reliability of both systems under stochastic scenarios. The proposed model, employing Sequential Monte Carlo (SMC) within its optimization framework, seeks to minimize investment, operation, and reliability costs. By addressing temporal uncertainties in component outages for both systems and considering uncertainties in power and gas system loads with a high temporal resolution and annual load growth, the model provides a comprehensive reliability perspective. Furthermore, sensitivity analysis is conducted to explore the impact of varying Values of Lost Load (VOLL) on the planning results. Numerical evaluation, using two integrated energy systems including IEEE 14-bus-10-gas node, and large-scale energy systems including IEEE 118-bus-85-gas node integrated power-gas system (IPGS), demonstrates a significant 12.53 % improvement in overall system reliability. Furthermore, a 2.81 % reduction in operation costs and a substantial 26.3 % reduction in reliability costs, validating the effectiveness of the proposed model.

Application of artificial neural network for peak load forecasting in 150 kV Semarang power system

Accurate load forecasting is essential for reliable and efficient operation of power systems. Traditional forecasting methods often struggle with capturing complex nonlinear patterns in load data. Artificial neural networks (ANNs) have emerged as a promising alternative due to their ability to learn complex relationships from historical data (Syed et al. in IEEEA 9:54992–55008, 2021. https://doi.org/10.1109/ACCESS.2021.3071654). This study investigates the potential of ANNs for short-term peak load forecasting in a 150 kV power system in Semarang, Indonesia. The study examines the impact of different input variables, including historical peak load, minimum load, population, and energy production, on forecasting accuracy. Several ANN architectures are trained and evaluated using mean absolute percentage error (MAPE) and mean squared error (MSE) metrics as reported by Demuth and De Jesús (neural network design). The results indicate that ANNs can achieve high accuracy in predicting peak load, with MAPE values below 10%. The study also demonstrates the importance of carefully selecting input variables and training parameters for optimal model performance. The findings highlight the potential of ANNs for improving load forecasting accuracy in power systems, contributing to enhanced grid reliability and operational efficiency. The findings of this study contribute to a deeper understanding of the application of ANNs in power system load forecasting. They demonstrate the potential of ANNs to achieve high accuracy and provide valuable insights into the factors influencing model performance. The findings are relevant for power system operators, researchers, and policymakers working to improve grid reliability and efficiency as reported by Prabha Kundur and Malik (Power System Stability and Control, McGraw-Hill Education, New York, 2022. https://www.accessengineeringlibrary.com/content/book/9781260473544).

Study on the Evolutionary Process and Balancing Mechanism of Net Load in Renewable Energy Power Systems

With the rapid development of renewable energy sources such as wind and solar, the net load characteristics of power systems have undergone fundamental changes. This paper defines quantitative analysis indicators for net load characteristics and examines how these characteristics evolve as the proportion of wind and solar energy increases. By identifying inflection points in the system’s adjustment capabilities, we categorize power systems into low, medium, and high renewable energy penetration. We then establish adjustment models that incorporate traditional coal power, hydropower, natural gas generation, adjustable loads, system interconnections, pumped-storage hydroelectricity, and new energy storage technologies. A genetic algorithm is employed to optimize and balance the net load curves under varying renewable energy proportions, analyzing the mechanism behind net load balance. A case study, based on real operational data from 2023 for a provincial power grid in western China, which is rich in renewable resources, conducts a quantitative analysis of the system’s adjustment capability inflection point and net load balancing strategies. The results demonstrate that the proposed method effectively captures the evolution of the system’s net load and reveals the mechanisms of net load balancing under different renewable energy penetration levels.

On the Uniqueness of the Solution of Electric Power System Load Flow Nonlinear Equation Systems in the Form of a Power Balance

On the Uniqueness of the Solution of Electric Power System Load Flow Nonlinear Equation Systems in the Form of a Power Balance

Assessment of the Renewable Energy Consumption Capacity of Power Systems Considering the Uncertainty of Renewables and Symmetry of Active Power

The rapid growth of renewable energy presents significant challenges for power grid operation, making the efficient integration of renewable energy crucial. This paper proposes a method to evaluate the power system’s capacity to accommodate renewable energy based on the Gaussian mixture model (GMM) from a symmetry perspective, underscoring the symmetrical interplay between load and renewable energy sources and highlighting the balance necessary for enhancing grid stability. First, a 10th-order GMM is identified as the optimal model for analyzing power system load and wind power data, balancing accuracy with computational efficiency. The Metropolis–Hastings (M-H) algorithm is used to generate sample spaces, which are integrated into power flow calculations to determine the maximum renewable energy integration capacity while ensuring system stability. Short-circuit ratio calculations and N-1 fault simulations validate system robustness under high renewable energy integration. The consistency between the results from the M-H algorithm, Gibbs sampling, and Monte Carlo simulation (MCS) confirms the approach’s accuracy.

Harmonic State Estimation in Power Systems Using the Jaya Algorithm

The increasing use of nonlinear loads in power systems introduces voltage and current components at non-fundamental frequencies, leading to harmonic distortion, which negatively impacts electrical and electronic devices. A common mitigation strategy involves identifying harmonic sources and installing filters nearby. However, due to the high cost of power quality (PQ) meters, comprehensive harmonic level monitoring across the entire power system is impractical. To address this, various methodologies for Harmonic State Estimation (HSE) have been developed, which estimate distortion levels on unmonitored system buses using data from a minimal set of monitored ones. Many HSE techniques rely on optimization algorithms with numerous tuning parameters, complicating their application. This paper proposes a novel methodology for fundamental frequency power flow and harmonic state estimation using the Jaya algorithm, which is characterized by fewer tuning parameters for easier adjustment. It also introduces a strategy to determine the minimal number of buses that need monitoring to achieve system observability. The methodology is validated on the IEEE-14 and IEEE-30 bus systems, demonstrating its effectiveness. The results of the proposed methodology are compared with those obtained using Evolutionary Strategies (ESs), highlighting its enhanced accuracy and computational efficiency.

Dynamic prediction of overhead transmission line ampacity based on the BP neural network using Bayesian optimization

Traditionally, the ampacity of an overhead transmission line (OHTL) is a static value obtained based on adverse weather conditions, which constrains the transmission capacity. With the continuous growth of power system load, it is increasingly necessary to dynamically adjust the ampacity based on weather conditions. To this end, this paper models the heat balance relationship of the OHTL based on a BP neural network using Bayesian optimization (BO-BP). On this basis, an OHTL ampacity prediction method considering the model error is proposed. First, a two-stage current-stepping ampacity prediction model is established to obtain the initial ampacity prediction results. Then, the risk control strategy of ampacity prediction considering the model error is proposed to correct the ampacity based on the quartile of the model error to reduce the risk of the conductor overheating caused by the model error. Finally, a simulation is carried out based on the operation data of a 220-kV transmission line. The simulation results show that the accuracy of the BO-BP model is improved by more than 20% compared with the traditional heat balance equation. The proposed ampacity prediction method can improve the transmission capacity by more than 150% compared with the original static ampacity.

Key technologies and applications of collaboration between digital power grid and Internet of Things

AbstractThe integration of electricity technology and information technology, such as the Internet of Things (IoT), enables the construction of new power systems, along with the innovation of application scenarios and business scope. The key technologies of power IoT and the data flow process are summarised first. The IoT technology and application scenario requirements of power generation, transmission, loading, and storage of new power systems are studied. Thus, the nature of the collaborative development of the digital power grid and the IoT is demonstrated from the perspective of data processing in power IoT and application requirements in power systems. The key problems and solutions faced by the power IoT under the digital transformation are described, and the cross‐integration of key technologies and promotion of application scenario innovation are prospected. Finally, the key issues of future technological development were discussed, providing reference ideas for fully leveraging the value of energy and electricity data production factors and promoting the construction of a digital electricity ecosystem.

Globally optimal sequencing of optimal reactive dispatch control adjustments to minimize operational losses in transmission systems by graph shortest path, parallel computing, and dynamic programming

Minimizing operational losses in transmission systems through the Optimal Reactive Dispatch (ORD), a non-convex mixed-integer nonlinear programming problem, is crucial for operational cost reduction, resource optimization, and greenhouse gas emission mitigation. Besides all intricacies associated with solving ORDs, transmission system operators encounter the challenge of determining sequences in which ORD control adjustments must be implemented before significant changes occur in generators scheduled power output and system loading. Sequencing ORD control adjustments, in spite of not being novel, remains modestly scrutinized in the literature. This paper introduces a two-phase framework that tackles the globally optimal sequencing of n ORD control adjustments over n! potential paths by solving the ORD to minimize operational losses in transmission systems in the first phase, and optimally sequencing ORD control adjustments employing fast power flow calculations, graph shortest path, parallel computing, and dynamic programming in the second phase. We discuss the framework’s second phase asymptotic time complexity, which is exponential over factorial for brute-force approaches, and its capability to guarantee globally optimal paths toward minimal operational losses determined in the framework’s first phase. ORD control adjustments for transmission systems with up to 27 controllable variables are benchmarked against two mixed-integer nonlinear programming solvers: BARON, a global non-convex solver, and Knitro, a local solver (assuming convexity around local optima). Globally optimal sequences of ORD control adjustments over n! potential paths (more than 1028 for sequencing 27 control adjustments) and average algorithm runtimes validate the straightforward application and, more importantly, effectiveness of such a comprehensive framework.

Power system loading margin enhancement based on a multi-objective TCSC placement to mitigate the risk of blackouts

In the evolving power systems, loading margin (LM) enhancement has a significant effect on the mitigation of the risk of cascading line outages and thereby the occurrence of large blackouts. On the other hand, flexible alternating current transmission system (FACTS) devices, especially thyristor-controlled series compensated (TCSC) devices, are more effective than other mitigation strategies such as constructing new lines because of environmental and economic reasons. In this paper, a multi-objective framework is presented to maximize the LM with a minimum installation cost of TCSCs. The optimization problem is solved by using the ɛ-constraint method. The benefit of each Pareto solution is calculated by the probabilistic risk assessment, and the most preferred one is selected by a benefit/cost analysis. The proposed method is developed based on a modified alternating current (AC) version of the ORNL–Pserc–Alaska (OPA) model inspired by the self-organized criticality (SOC) theory in complex power grids. Using the benefit/cost criterion, it is revealed that by the proposed approach, a larger value for the most preferred Pareto solution is obtained in comparison with the defined transmission expansion planning (TEP) scenarios. It confirms the suitability of the proposed method to suppress the cascading outages instead of expensive and time-consuming policies such as building new lines.

Hybrid Optimal Power System Recovery and Load Pick-Up With DGAllocation In Electrical Power System

The increasing demand for electricity, the expansion of complex power networks, and the operation of power systems near their capacity have heightened the risk of power outages. Consequently, control room operators must develop comprehensive restoration plans to minimize recovery time. Key steps in power system restoration include starting non-black-start units with black-start units and initiating load pick-up. This process requires identifying the shortest route between nodes to expedite repairs. This research presents an expert plan employing the Modified Cuckoo Search algorithm (MCSA) to determine optimal pathways. Additionally, it explores the optimal allocation of distributed generators (DG) to enhance the system's voltage profile and reduce power losses using particle swarm optimization (PSO). The results demonstrate that DG significantly reduces losses during recovery. The study prioritizes the restoration of DGs with strong black start capability, considering network and DG constraints. The effectiveness of the proposed restoration approach is validated through MATLAB simulations on theIEEE 39-bus system.

Ambient Signals based Load Modeling with Two Three-phase Induction Motors

Abstract The traditional electric power system simulation and calculation are based on the simple load model including one motor and one static load. On the one hand, the power system load is getting more and more complex. On the other hand, it’s proved that two kinds of three-phase induction motors will show a little difference. As a result, in this paper, a new model load with two three-phase induction motors is proposed. Besides, the dynamic of the power system load is taken into account. The torque of those two three-phase motors will show different characteristics, that one is constant and the other is variable. Formerly, the dynamic of the load is regarded as the result of an induction motor. However, the single-phase motor and electronic load both lead to the complexity of the load. To get a more accurate calculation, we need a more proper load model. One of the ways to improve the load model is to pay more attention to the ingredients ignored. The single-phase motor and power electronic load make a great difference. Besides, it’s proved that the composited load model with two three-phase motors will be better in the calculation.

Фінансові перешкоди впровадженню теплових насосів в централізованому теплопостачанні

The use of powerful industrial heat pumps (HP) is a fairly effective means of rational and environmentally friendly use of energy resources both in individual households and in district heating (DH), as well as in production processes in various industries. Powerful HPs are used in Ukraine much less than in developed European countries. In fact, these are isolated cases. The post-war reconstruction of destroyed cities with their district heating systems gives Ukraine a unique chance to use modern energy-efficient technologies, including HP. As a result, efficiency will improve and DH competitiveness will increase due to the low cost of thermal energy for consumers. Almost all developed countries of the world have government financial support for the HP implementation. The purpose of this study is to determine the level and form of government financial support for projects to implement HP in DHs of Ukraine. Financial modeling of the implementation of heat pump plants shown that they are more expediently to be used in the mode of generating thermal energy than in the mode of regulating the electric load of power systems. It is shown that the projects of heat pump plants, which use the heat of flue gases as a source of low-potential heat (LPH), are the most economically attractive and practically do not require government financial support. Projects of heat pump plants, which use air, ventilation emissions, waste water, soil and groundwater, sea, rivers, and waste heat of technological processes as LPH, are not financially attractive without government financial support, and some of them are even unprofitable. The most appropriate comprehensive financial support is tax incentives and interest compensation on the loan. Sensitivity analysis showed that projects for the implementation of heat pump plants may be the most sensitive to the amount of generated thermal energy, the price of natural gas and electricity. Keywords: heat pumps, low-potential heat sources, district heating, financial obstacles, tax incentives, grants.

Effect of Load Variation and Fault Resistance on the Operation Time of IDMT Overcurrent Relay

Fault can occur in power system due to many factors such as lightning, tree or crane encroachment, animal intervention, human error etc. Each fault occurrence has its own fault resistance value, and this value is unknown to the protection relay used to the protect the circuit. Besides that, the connected load in power system is dynamic where the value is changing over time. It is very important for the protection relay to be as reliable as it can so that the fault can be isolated as soon as possible when a fault occur. This paper study the effect of fault resistance value and load variation on IDMT overcurrent relay operation time. This relay is used to protect the line from fault occurrence where the higher the fault current, the faster the operation time will be. MATLAB Simulink has been used to model the transmission line, source, connected load and IDMT overcurrent relay. Faults simulations were conducted for various fault resistance and load values and the effects on relay operation time have been analysed. From the results, it was found that, the higher the fault resistance, the higher the operation time while the higher the value of connected load at the end of the line, the faster the relay operation time.

Power system load frequency management using fuzzy logic

A power system is a sizable, intricately linked network that has multiple sources and loads. The population growth causes variations and unpredictability in load demand. The utilities are responsible for meeting load demand while abiding by operational restrictions on the power system. Control of load frequency is alone in charge of providing the customers with sustainable electrical power. Its primary purpose is to control system frequency and power flow in additional areas within advised bounds by controlling tie-line power and the utility generator's output power in reaction to changes in load without compromising system frequency. The paper's recommended concept illustrates the load frequency control of two area systems using fuzzy logic, fuzzy tuned proportional integral, conventional proportional integral, and proportional integral derivative controllers. SIMULINK is used for simulation research.

Many-objective optimization based mutual feed scheduling for energy system of integrated energy station

The battery storage system of the integrated energy station contains electric vehicles as the distributed energy storage node of the regional power system can help the regional power system to achieve peak shaving and valley filling. This paper proposes a many-objective optimization based mutual feed model of the energy system of the integrated energy station. The model includes multiple modules of electric vehicle (EV), wind turbine (WT), photovoltaic (PV) and battery energy storage system (BESS). BESS was modeled according to the two behaviors of EVs charging and swapping. The model ensures the role of peak shaving and valley filling for regional power, reduces the loss of battery life in the battery storage system of the integrated energy station, and reduces the operating cost of the battery storage system. In the optimized results, the regional power system load peak-to-valley ratio by 28.72 %, and the daily battery charge/discharge life loss is minimized to 0.00036 %. In addition, for known many-objective optimization problems, this paper also proposes a new meta-heuristic many-objective optimization algorithm the non-dominated sorting hunter prey optimization (NSHPO for short) and compared with other four many-objective optimization algorithms by three indexes (Distribution range, Hypervolume index, and Running time). The simulation results show that compared with other algorithms, the HV metrics of NSHPO are lower by about 1.56 %-7.26 %, Spread metrics are better by about 0.39 %-2.73 %, and the proposed NSHPO algorithm is better in terms of convergence and distributivity.