Power Flow In Network Research Articles

Optimization of Active Distribution Network Operation with SOP Considering Reverse Power Flow

As the penetration of distributed renewable energy increases, the phenomenon of bidirectional power flow in distribution networks becomes increasingly severe. Traditional regulation devices like OLTC (on-load tap changer) and CB (capacitor bank) cannot effectively mitigate reverse power flow in distribution networks due to their limitations. The transmission capacity of the distribution network under reverse power flow is approximately 50% of the rated capacity of the OLTC, leading to issues such as voltage limit violations and high wind and solar curtailment rates. This paper proposes a method for calculating the reverse power flow delivery capacity of distribution networks, quantitatively describing the distribution network’s delivery limits for reverse power flow. Based on this, a joint optimization model for multiple distribution networks with an SOP is established. The SOP is utilized to share reverse power flow delivery capacity among multiple distribution networks, enhancing operational economy and increasing the accommodation of the DG. Finally, the method’s effectiveness and correctness are verified in the IEEE 33-node system. The results validate that while joint operation does not enhance the reverse flow transmission capacity of a single distribution network, it can, through the shared reverse flow transmission capacity approach, elevate the reverse flow transmission capacity to approximately 70% during the majority of time periods.

Comparative analysis of two static var compensator models in voltage control of transmission network

The static var compensator (SVC) is a member of the family of flexible alternating current transmission systems controllers used in power system engineering to manage specific transmission network characteristics to enhance the performance of the transmission networks and thus increase the networks’ reliability. Power system engineers typically find it difficult to choose which SVC model to implement for simulations. This research aims to address this issue by conducting a comparative examination of two key SVC models on a transmission network. The two models of SVC variable shunt susceptance and firing angle were mathematically modeled and methodically included into the Newton-Raphson power flow algorithm for the network power flow solution. The IEEE 30-bus network was adopted as the test case, and the method was implemented in the MATLAB/Simulink environment. The network performance metric utilized was the voltage profile of the network. The two SVC models were successful in enhancing the network's performance; however, the variable shunt susceptance model was computationally faster than the firing angle model, as revealed by the simulation results. Therefore, among the two SVC models, the variable shunt susceptance model may be taken into account for simulation to enhance the performance of the transmission networks.

The phenomenon and suppression strategy of overvoltage caused by PV power reverse flow

In the current distribution network’s energy structure, photovoltaic (PV) occupies a high proportion. However, the access of a high proportion of PV will lead to the phenomenon of reverse power flow in the distribution network, and then the problem of line overvoltage. When the reverse power flow increases, the problem of line overvoltage also worsens, which endangers the normal operation of power system. To solve this problem, this paper starts with the voltage rise theory of distribution network lines. Firstly, through strict mathematical derivation, it compares the influence of main network line parameters and distribution network line parameters on the voltage rise, and summarizes a simple calculation equation for the voltage rise of the distribution network with high proportion PV. Then, according to the mechanism of voltage rise and the principle of inverter control, considering the economy and practicability of the overvoltage suppression strategy, a reverse power flow overvoltage suppression strategy of a system with high proportion PV is proposed. Finally, a PV system model simulating a small village is used to verify the effectiveness of the proposed overvoltage suppression strategy.

Stochastic economic sizing and placement of renewable integrated energy system with combined hydrogen and power technology in the active distribution network

The current study concentrates on the planning (sitting and sizing) of a renewable integrated energy system that incorporates power-to-hydrogen (P2H) and hydrogen-to-power (H2P) technologies within an active distribution network. This is expressed in the form of an optimization model, in which the objective function is to reduce the annual costs of construction and maintenance of integrated energy systems. The model takes into account the planning and operation model of wind, solar, and bio-waste resources, as well as hydrogen storage (a combination of P2H, H2P, and hydrogen tank), and the optimal power flow constraints of the distribution network. Electrical and hydrogen energy are administered in an integrated energy system. The modeling of the uncertainties regarding the quantity of load and renewable resources is achieved through stochastic optimization using the Unscented Transformation method. The novelties of the scheme include the sizing and placement of a combined hydrogen and power-based renewable integrated energy system, the consideration of the impacts of bio-waste units, P2H, and H2P systems on the planning of the integrated energy system and the operation of the active distribution network, and the modeling of uncertainties using the Unscented Transformation method to reduce the calculation time. The study’s results demonstrate the scheme’s ability to improve the technical conditions of the distribution network by considering the optimal planning of integrated energy systems. In comparison to the network power flow, the operation status of the network has been improved by approximately 23-45% through the optimal siting, sizing, and energy management of hydrogen storage equipment, as well as renewable resources in the form of integrated energy systems. In other words, optimal energy management and planning of the integrated energy systems in the distribution network has been able to reduce energy losses and voltage drop by 44.5% and 42.4% compared to the load flow studies. In this situation, peak load carrying capability has increased by about 23.7%. In addition, compared to the case of the network with renewable resources, the overvoltage has decreased by about 43.5%. Also, Unscented Transformation method has a lower calculation time than scenario-based stochastic optimization.

Security constrained optimal power flow solution for practical transmission grid using hybrid use of generating plant and network restructuring

This paper presented a study on the security constrained optimal power flow (SCOPF) of a practical transmission utility grid network (TUGN). The objectives of reduction in the transmission losses of TUGN (TLGN) and to minimize the bus voltage deviations (BVD) are achieved by addition of thermal power plant (TPP) and network restructuring (NR). Identification of best fit node for generation injection is achieved using the method based on hybrid combination of analytic approach and genetic algorithm (GA). Efficacy of the proposed study is evaluated using the computation of energy equivalent to network loss saving, percentage derating of the load (PDOL), voltage profile, bus voltage deviations, and financial analysis (FA). Study is performed without and with contingency (N-1) for the base case network, TUGN with addition of TPP and TUGN with addition of TPP and NR. This is established that addition of TPP, addition of TPP with NR are effective to reduce the TLGN, improve the voltage profile and minimize the bus voltage deviations. This study is more efficient compared to various studies reported in literature.

Decentralized Optimal Power Flow for Multi-Agent Active Distribution Networks: A Differentially Private Consensus ADMM Algorithm

Decentralized Optimal Power Flow for Multi-Agent Active Distribution Networks: A Differentially Private Consensus ADMM Algorithm

Power flow analysis and volt/var control strategy of the active distribution network based on data-driven method

In order to solve the problems of low power flow calculation accuracy and voltage overcrossing of the distribution network caused by large-scale distributed power supply, a data-driven power flow analysis and volt/var optimization control strategy for distribution network are proposed in this paper. Firstly, a data-driven power flow analysis model for the distribution network is proposed, and the nonlinear mapping relationship between the distribution network state and power flow results is described from the data-driven perspective. Secondly, the paper analyzes the influence of photovoltaic power supply on the voltage of the distribution network, and establishes the volt/var optimization model based on photovoltaic power supply. Then, on the basis of data-driven power flow analysis of the distribution network, the distribution network reactive voltage optimization strategy based on data-driven power flow analysis is proposed to ensure the safe and stable operation of distribution network voltage, reduce the operating network loss of distribution network, and realize the distribution network reactive voltage optimization is not affected by factors such as distribution network line parameters. Finally, IEEE 33 node power distribution system is used to verify the effectiveness of the proposed strategy.

Data-model driven probability model of branch power flow for distribution networks and its application to analysis of overload and line loss

The fluctuation of highly penetrated distributed generations (DGs) in distribution networks (DNs) increases branch overload risks, which makes the analysis uncertainty of branch power flow more complex. The probability analysis of branch power can grasp the power flow operation characteristics under uncertain conditions, which supports the power flow optimization management and ensures the safe and economic operation of DNs. Therefore, this paper proposes a data-model driven probability analysis method for branch power flow in DNs. An approximate branch power model is first derived to reveal the analytical relationship between branch power and node power. Then, based on the branch power approximation model and the forecasting error, the datasets of branch apparent power are constructed to capture the complex nonlinear characteristics of the power flow. The non-Gaussian distribution characteristics of branch apparent power and line loss are described by the optimal probability fitting method. Finally, the probability level of branch overload is evaluated and the probability distribution of line loss is analyzed. The case studies demonstrate that the branch power approximation model is highly accurate, and the probability distribution of the branch apparent power presents different characteristics. The proposed method can quickly and accurately calculate the branch overload probability level.

Optimal Power Flow Calculation Based on Improved Crossover Algorithm

Abstract Aiming at the optimization problem of power flow distribution in power system, this paper puts forward a method for calculating the optimal power flow of power network based on the improved crisscross algorithm. The fast convergence crisscross optimization algorithm (FCSO) is based on the traditional crisscross optimization algorithm (CSO) to improve the efficiency and accuracy of solving the Optimal Power Flow, OPF) problem. Based on the original double crossover operator, the improved algorithm puts forward a brand-new operator-central crossover operator, which alternates with transverse crossover operator according to certain rules, In order to improve the quality of single search and accelerate convergence, each individual in the population performs crossover operation with the current optimal individual in turn, and then performs competition operator to selectively approach the current global optimal individual. Finally, combined with experimental verification, the optimal power flow calculation of reactive power optimization based on FSCO has obvious practical effects in improving network voltage quality and reducing line loss, The average voltage increase ratio of 220kV bus and 110kV bus is 0.676% and 0.855% respectively, and the loss reduction rate reaches 3.51%, Compared with CSO, the convergence and calculation speed of FSCO proposed in this paper is faster, the convergence curve is smoother, and the average time consumption is increased to 59.53% compared with CSO, In the case of obtaining the same precision solution, the optimization time is obviously shortened, the timeliness of the optimal solution in regulation operation is effectively improved, and the problem of reactive power optimization in power system can be well solved.

Real-Time Power Regulation of Flexible User-Side Resources in Distribution Networks via Dual Ascent Method

Flexible user-side resources are of great potential in providing power regulation so as to effectively address the challenges of reverse power flow and overvoltage issues in distribution networks characterized by high photovoltaic (PV) penetration. However, existing distributed algorithms typically implement control signals after the convergence of the algorithms, making it difficult to track frequent and rapid fluctuations in PV power outputs in real time. Given this background, an online-distributed control algorithm for the real-time power regulation of flexible user-side resources is proposed in this paper. The objective of the established control model is to minimize network losses by dynamically adjusting active power outputs of flexible user-side resources and reactive power outputs of PV inverters while respecting branch power flow and voltage magnitude constraints. Furthermore, by deconstructing the centralized problem into a primal–dual one, a distributed control strategy based on the dual ascent method is implemented. With the proposed method, agents can achieve global optimality by exchanging limited information with their neighbors. The simulation results verify the good balance between economic efficiency and voltage control performance of the proposed method.

Distributed flexible resource regulation strategy for residential communities based on deep reinforcement learning

AbstractIn an era characterized by the rapid proliferation of distributed flexible resources (DFRs), the development of customized energy management and regulation strategies has attracted significant interest from the field. The inherent geographical dispersion and unpredictability of these resources, however, pose substantial barriers to their effective and computationally tractable regulation. To address these impediments, this paper proposes a deep reinforcement learning‐based distributed resource energy management strategy, taking into account the inherent physical and structural constraints of the distribution network. This proposed strategy is modelled as a sequential decision‐making framework with a Markov decision process, informed by physical states and external information. In particular, targeting the community energy management system for critical public infrastructure and community holistic benefits maximization, the proposed approach proficiently adapts to fluctuations in resource variability and fluctuating market prices, ensuring intelligent regulation of distributed flexible resources. Simulation and empirical analysis demonstrate that the proposed deep reinforcement learning‐based strategy can improve the economic benefits and decision‐making efficiency of distributed flexible resource regulation while ensuring the security of distribution network power flow.

Optimization of the power–transportation coupled power distribution network based on stochastic user equilibrium

With the increasing penetration of electric vehicles (EVs) in road traffic, the spatial and temporal stochasticity of the travel pattern and charging demand of EVs as a mode of transportation and an electrical load have generated different degrees of congestion impacts on both the power grid and the transportation network. Based on this, this paper proposes a power–transportation-coupled distribution network optimization strategy based on stochastic user traffic equilibrium theory. First, a stochastic user equilibrium-mixed traffic flow allocation model that expresses user non-completely rational path selection behavior is established, and the traffic flow equilibrium solution is obtained using an improved method of successive algorithm and mapped to charging loads. Second, a distribution network power flow optimization model under the coupled power–transportation architecture is established to optimize the operation state of the distribution network by combining distributed resources such as energy storage, demand response loads, wind power, photovoltaic, and gas turbines.

Sensitivity Analysis and Distribution Factor Calculation under Power Network Branch Power Flow Exceedance

As the scale of power systems continue to expand and their structure becomes increasingly complex, it is likely that branch power flow exceedance may occur during the operation of power systems, posing threats to the safe and stable operation of entire systems. This paper addresses the issue of branch flow exceedance in power networks. To enhance the operational efficiency and optimize the adjustment effects, this paper proposes a method for eliminating branch power flow exceedance by improving the particle swarm optimization (PSO) algorithm through the introduction of sensitivity and distribution factors. Firstly, it introduces the basic theory and calculation methods of sensitivity analysis, focusing on deriving the calculation principles of power flow sensitivity and voltage sensitivity, used to predict the responses of power flow at each branch in the power network to power or voltage changes. Subsequently, the paper provides a detailed derivation of the calculation principles for the line outage distribution factor (LODF), which effectively assesses the changes in branch power flow in the power network under specific conditions. Finally, a method for eliminating branch power flow exceedance based on a combination of sensitivity analysis and PSO algorithm is proposed. Through case analysis, it is demonstrated how to use the sensitivity and distribution factor to predict and control the power flow exceedance issues in power systems, verifying the efficiency and practicality of the proposed method for eliminating branch power flow exceedance. The study shows that this method can rapidly and accurately predict and address branch power flow exceedance in power system, thereby enhancing the operational safety of the power system.

A Method for Power Flow Calculation in AC/DC Hybrid Distribution Networks Considering the Electric Energy Routers Based on an Alternating Iterative Approach

With the advancement of new power system construction, distribution networks are gradually transforming from being a simple energy receiver and distributor to being an integrated power network that integrates sources, networks, loads, and energy storage with interactive and flexible coupling with the upper-level power grid. However, traditional distribution networks lack active control and distribution capabilities, failing to meet the demands of network transformation and upgrading. To address this issue, this paper proposes a method for solving AC/DC power flow calculation considering an electric energy router (EER) based on an alternating iterative method. Initially, the model for the multi-port EER and three types of power flow models for the AC distribution network, DC distribution network, and EER are constructed. By leveraging the properties of the EER and the hybrid power flow calculation model, a method is proposed for calculating the power flow in the AC/DC hybrid distribution network considering the EER. Finally, by solving the power flow in a medium- and low-voltage AC/DC distribution system, the adaptability of the proposed method is compared. The results demonstrate that the AC/DC hybrid distribution network power flow calculation method established in this paper, which incorporates the EER, possesses high accuracy and adaptability, with an error margin of less than 0.05%.

An Active Learning Local Control Method for Optimal Power Flow in Low Voltage Distribution Networks Considering Missing Data

An Active Learning Local Control Method for Optimal Power Flow in Low Voltage Distribution Networks Considering Missing Data

Unlocking responsive flexibility within local energy communities in the presence of grid-scale batteries

The transition towards a decentralized, decarbonized, and distributed energy infrastructure necessitates techno-economic initiatives to empower local energy communities (LECs) to achieve self-reliance and evolve into self-sustained electricity networks. It is crucial to underscore the significance of network resilience, especially in the context of local power generation, battery storage, and the radial topology of low-voltage (LV) networks. While contemporary LV networks have made significant attempts to integrate distributed energy resources (DERs), the notable deficiency lies in their lack of network redundancy, posing a substantial challenge in the occurrence of high-impact, low-probability (HILP) events. Therefore, to enhance LV network resilience and leverage its capability to withstand unexpected disruptions, the network operator needs to unlock the potential contributions of end-users within the active distribution networks (ADNs). In this paper, a comprehensive model is developed based on multi-temporal optimal power flow (MTOPF) for unbalanced LV networks addressing the technical issues in islanded microgrid operational planning. The contributions of the grid-scale batteries in forming islanded microgrids and the flexibility that can be provided by the end-users in the LEC have been considered in this paper. To demonstrate the performance of the proposed model, the simulation studies have been carried out on a part of medium and low voltage networks, consisting of network reconfiguration and load transferring capability to reduce the service interruptions during HILP events. The energy-not-served (ENS) is chosen as one of the key performance indicators (KPIs) in this study. With the unlocking flexibility potentials and contribution of the DERs, including grid-scale energy storage (GES) units and Photovoltaic (PV) panels, the ENS has been reduced from 700.8 kWh to 447.5 kWh by activating the local resources, proper switching action, and contribution of the flexible loads, for one of the severe HILP events, i.e., the main grid outage. In this case, the full load curtailment index is reduced from 180 to 106 client hours.

Analysis of the Influence of Distributed Photovoltaic Access on the Operation Quality of Asymmetry Distribution Network

Abstract Distributed photovoltaic(PV) power generation, as a highly flexible renewable energy source, is currently developing rapidly and has been widely used. However, due to its uncertainty and randomness, large-scale distributed photovoltaic integration into the distribution network will change the network power flow distribution, which will have a greater impact on the operation quality of the distribution network operation. In order to study the influence of distributed PV access on the operation of asymmetry distribution network, this paper builds a three-phase power flow model of distributed photovoltaic access to distribution network. Based on the IEEE33 node three-phase calculation example data, the impact of distributed photovoltaic access location and capacity on a series of operation indicators such as voltage deviation, three-phase unbalance and network loss under asymmetry operation of the distribution network is studied. Finally, for the asymmetry distribution network operating condition, guidance suggestions for distributed photovoltaic access based on operation quality are given.

Energy Consumption Management of Residential Appliances Based on Load Signatures Decomposition

Nowadays, energy consumption management techniques in the residential side have gained significant importance due to their considerable influence on the control of power flow in distribution networks and especially the possibility of managing a huge part of domestic electrical demand during peak-load hours. Since the customer’s data are recorded in an aggregated form, therefore, in order to apply control approaches, it is necessary to use load pattern evaluation techniques (load signature). These methods capable to decomposition effective features that help control approaches to implement with more accuracy. In this article, features of residential loads have been extracted by using the signature of the aggregated consumer’s demand. Then these features have been evaluated by methods such as logistic regression, k-nearest neighborhood, and decision tree. By assessing the results, it was determined that among the extracted features, the first two features (consumed power and injected harmonics) covered more than 89% of the variance of the entire set, and with the help of using the principal component analysis method, it was determined that by reducing the number of features to 2, a considerable amount of computation is reduced and only about 4% of the accuracy is reduced. Also, the convolutional neural network approach was used to estimate the type of load, and by identifying controllable loads and applying remote home energy management methods, it was found that by increasing participation up to 80%, more than 41% of peak-load consumption could be shifted to off-peak hours.

Analysis of power quality and additional loss in distribution network with distributed generation

As the penetration of distributed generation in the power grid, the power quality issues in the active distribution network are becoming increasingly diversified, hence followed with complex changes of the additional loss. The article investigates the additional loss caused by disorder power flow and power quality disturbances in the active distribution network. Firstly, the active distribution network model is established based on typical parameters. The impact of the access of distributed generation on power quality issues, including three-phase imbalance, harmonic distortion and voltage deviation and rise, is analyzed. Then, the influence of different power quality disturbances on additional loss with distributed generation is quantitatively explored. By introducing the concept of harmonic three-phase imbalance, the article analyzes the variation characteristics of network loss under the disturbances of composite power quality issues, and introduces the concept of a loss reduction interval, whose size is related to the average current. Finally, the validity of the analysis is verified through simulation. This article provides a new approach for loss analysis in distribution network containing distributed generation, which is beneficial for identifying and minimizing network loss in distribution networks.

Research on the minimum network loss optimization control strategy of the active distribution network based on the distributed power flow controller

With large-scale access to distributed new energy, the power flow form of the distribution network tends to be complex. The distribution loop network rate increases, resulting in serious circulation of the distribution network, which places significant pressure on the loss of the distribution network. The problem of network loss change caused by distributed new energy grid connection, coupled with the inconsistency between load fluctuation and output power change of distributed new energy, will have a significant impact on the safety, reliability, and economic operation of the distribution network. Therefore, it is urgent to have good economic and technical means of power flow control. This paper proposes a minimum network loss optimization control strategy for active distribution networks based on a distributed power flow controller. First, according to the characteristics of the distribution network load and the new energy power supply along the distribution line, the multiple sub-modules of the distributed power flow controller are arranged in sections in the distribution loop network line. The regulation effect of the distributed power flow controller on the voltage and power flow of the distribution loop network is analyzed. The loop network current equation and power loss equation after the distributed power flow controller are constructed, and the power equation with the minimum active loss of the active distribution loop network is derived. Second, the control strategy for minimum network loss of the active distribution network based on the distributed power flow controller is proposed. Finally, the simulation model of the active distribution loop network is constructed by PSCAD/EMTDC. The loss of the loop network before and after the distributed power flow controller is simulated and analyzed, and the effectiveness of the proposed strategy is verified.