Post-production Treatments Research Articles

Innovative 3D-Printed Titanium Specimens Favor a Modulation of Inflammation in Dental Pulp Stem Cells During Liposome-Triggered Mineralization.

developing customized titanium specimens, with innovative surfaces, is a suitable strategy to overcome implant failure. Additionally, a faster and efficient osteogenic commitment assists tissue regeneration. To investigate the interplay between inflammation and differentiation upon implantation, Dental Pulp Stem Cells (DPSCs) were cultured on 3D-printed titanium owning an internal open cell form, administering osteogenic factors by a liposomal formulation (LipoMix) compared to traditional delivery of differentiation medium (DM). osteogenic differentiation was evaluated by western blot, by measuring β1 integrin expression, and by and real-time RT-PCR, by measuring SP7 and Collagen I gene expression; while.angiogenesis was characterized by measuring VEGF secretion levels. Matrix mineralization was assessed by means of Alizarin Red Staining, cell adhesion and inflammation responses through western blot, enzymatic and ELISA assays evaluating Nrf2 expression, catalase activity and Prostaglandin E2 secretion, respectively. LipoMix enhances cell proliferation and adhesion, as revealed by increased integrin β1 expression. Mineralized matrix deposition, SP7 gene expression, Collagen I release and Alkaline Phosphatase activity appear increased in LipoMix condition. Additionally, the redox-sensitive transcription factor Nrf2 is overexpressed at the earliest experimental times, triggering the catalase activity. data reported confirm that internal topography and post-production treatments on titanium surfaces dynamically and positively condition the DPSC progress towards the osteogenic phenotype, moreover, the combination with LipoMix fastens the positive modulation of inflammation under osteogenic conditions. Therefore, the development of customized surfaces along with the administration of differentiating factors enclosed in a liposomal delivery system, could represent a promising and innovative tool in regenerative dentistry.

Recent advances on metal-organic frameworks (MOFs) and their applications in energy conversion devices: Comprehensive review

Metal-organic frameworks (MOFs) have enticed huge interest over the years in a wide range of applications, including electrochemical energy storage/conversion devices, due to their controllable porous structure, tuneable composition, excellent thermal/chemical stabilities, and facile synthesis. However, conductivity enhancement and synthesis of redox-active MOFs are two key challenges hindering their large-scale applications in electrochemistry. Redox-active MOFs can be prepared using redox-active ligands and metal ions, which in turn leads to an additional benefit of π-stacking interactions. Conductivity improvements through favourable overlap of energy and orientation of both metal and ligand, π-π stacking, and the incorporation of a guest molecule to induce free charge carriers and reduce band gaps are key strategies. This review provides a detailed assessment of various synthesis techniques followed by post-production treatments to improve MOF's conductivity. Advancements in computational methods & machine learning for MOFs as well as the econmics of MOF's production are introduced. The use of MOFs and MOF-based nanomaterials in batteries, supercapacitors, and fuel cells, as well as the progress in using MOF and MOF-based catalysts for CO2 reduction and as a photocatalyst for hydrogen production, have been scrutinized by highlighting their benefits and shortcomings. Finally, the challenges MOFs and MOF-based materials face and their prospects when adopted as active materials in energy storage/conversion devices, as well as CO2 reduction and green hydrogen production, have also been elaborated.

Hydrogen-Assisted Thermal Treatment of Electrode Materials for Electrochemical Double-Layer Capacitors.

The capacitance of electrode materials used in electrochemical double-layer capacitors (EDLCs) is currently limited by several factors, including inaccessible isolated micropores in high-surface area carbons, the finite density of states resulting in a quantum capacitance in series to Helmholtz double-layer capacitance, and the presence of surface impurities, such as functional groups and adsorbed species. To unlock the full potential of EDLC active materials and corresponding electrodes, several post-production treatments are commonly proposed to improve their capacitance and, thus, the energy density of the corresponding devices. In this work, we report a systematic study of the effect of a prototypical treatment, namely H2-assisted thermal treatment, on the chemical, structural, and thermal properties of activated carbon and corresponding electrodes. By combining multiple characterization techniques, we clarify the actual origins of the improvement of the performance (e.g., > +35% energy density for the investigated power densities in the 0.5-45 kW kg-1 range) of the EDLCs based on treated electrodes compared to the case based on the pristine electrodes. Contrary to previous works supporting a questionable graphitization of the activated carbon at temperatures <1000 °C, we found that a "surface graphitization" of the activated carbon, detected by spectroscopic analysis, is mainly associated with the desorption of surface contaminants. The elimination of surface impurities, including adsorbed species, improves the surface capacitance of the activated carbon (CsurfAC) by +37.1 and +36.3% at specific currents of 1 and 10 A g-1, respectively. Despite the presence of slight densification of the activated carbon upon the thermal treatment, the latter still improves the cell gravimetric capacitance normalized on the mass of the activated carbon only (CgAC), e.g., + 28% at 1 A g-1. Besides, our holistic approach identifies the change in the active material and binder contents as a concomitant cause of the increase of cell gravimetric capacitance (Cg), accounting for the mass of all of the electrode materials measured for treated electrodes compared to pristine ones. Overall, this study provides new insights into the relationship between the modifications of the electrode materials induced by H2-assisted thermal treatments and the performance of the resulting EDLCs.

Valorization and food applications of okara (soybean residue): A concurrent review.

Agriculture waste is rising continuously across the globe due to enormous industrial, food processing, and household activities. Proper valorization of this waste could be a promising source of various essential bioactive and functional ingredients. Okara is a major residue produced as result of soybean processing and has a rich nutritional profile. The nutritional profile of okara is affected by the processing conditions, variety, pre-treatment, post-production treatments, and processing techniques. Owing to the high fibers, lipids, proteins, and bioactive components, it is being used as an essential industrial ingredient in various food processing industries. The prebiotic potential and nutritional profile can be increased by various techniques, that is, enzymatic, chemical, biotransformation, high-pressure microfludization, and fermentation. The prebiotic potential of okara makes it suitable as a therapeutic agent to prevent a variety of metabolic disorders such as diabetes, obesity, hypercholesterolemia, and hyperlipidemia. The current review highlights the structural, nutritional, functional, therapeutic, and industrial applications of okara.

A comparative analysis of the effect of post production treatments and layer thickness on tensile and impact properties of additively manufactured polymers

Abstract In recent years, additive manufacturing (AM) technologies have become greatly popular in the polymer, metal, and composite industries because of the capability for rapid prototyping, and appropriateness for the production of complex shapes. In this study, a comprehensive comparative analysis focusing on the influence of post-processing types (heat treatment and water absorption) on tensile and impact responses was carried out on 3D printed PETG, PLA, and ABS. In addition, layer thickness levels (0.2, 0.3, and 0.4 mm) were selected as a major production parameter and their effect on mechanical properties was combined with post-processing type for the first time. The results showed that both tensile and impact resistance of the printed polymers increased thanks to the heat treatment. The highest tensile strength was measured for heat-treated PLA, while the peak impact endurance level was reached for heat-treated PETG. Also, water absorption caused a mass increment in all samples and induced higher tensile elongation values. Decreasing layer thickness had a positive effect on tensile features, but impact strength values dropped. On the other hand, all samples were subjected to macro and micro failure analyses to understand the deformation mechanism. These inspections indicated that for impact samples straight crack lines converted to zigzag style separation lines after the heat treatment. As for the tensile samples, the exact location of the main damage zone altered with the production stability, the water absorption capacity of the polymer, and the thermal diffusion ability of the filament.

Assessing biocompatibility & mechanical testing of 3D-printed PEEK versus milled PEEK

ObjectivesTo compare mechanical properties of 3D-printed and milled poly-ether-ether-ketone (PEEK) materials. To define post-production treatments to enhance biocompatibility of 3D-printed PEEK. MethodsStandardised PEEK samples were produced via milling and fused-deposition-modelling 3D-printing. To evaluate mechanical properties, tensile strength, maximum flexural strength, fracture toughness, and micro-hardness were measured.3D printed samples were sandblasted with 50 or 125 μm aluminium oxide beads to increase biocompatibility.Scanning electron microscopy (SEM) evaluated microstructure of 3D-printed and sandblasted samples, estimating surface roughness at scales from 1mm-1μm.Cell adhesion on 3D printed and sandblasted materials was evaluated by culturing primary human endothelial cells and osteoblasts (HUVEC, HOBS) and evaluating cell growth over 48 h. Results3D printed materials had lower tensile strength, flexural strength, and fracture toughness, but higher micro-hardness.SEM analysis of 3D-printed surfaces showed sandblasting with 125 and 50 μm silica particles removed printing defects and created roughened surfaces for increased HUVEC and HOBs uniform cell adhesion and distribution. No cytotoxicity was observed over a 48h period, and all cells demonstrated >95% viability. Clinical significance3D-printing of PEEK is an emerging technology with clear advantages over milling in maxillofacial implant production. Nonetheless, this manufacturing modality may produce 3D printed PEEK devices with lower mechanical resistance parameters compared to milled PEEK but with values compatible with natural bone. PEEK has poor osteoconductivity and ability to osseointegrate. Sandblasting is an inexpensive modality to remove irregular surface defects and create uniform micro-rough surfaces supporting cell attachment and potentially enhancing integration of PEEK implants with host tissue.

Morphological integrity of insulin amyloid-like aggregates depends on preparation methods and post-production treatments

Protein aggregates are often varying extensively in their morphological characteristics, which may lead to various biological outcomes, such as increased immunogenicity risk. However, isolation of aggregates with a specific morphology within an ensemble is often challenging. To gain vital knowledge on the effects of aggregate characteristics, samples containing a single morphology must be produced by direct control of the aggregation process. Moreover, the formed aggregates need to be in an aqueous solution suitable for biological assays, while keeping their morphology intact. Here we evaluated the dependence of morphology and integrity of amyloid-like fibrils and spherulites on preparation conditions and post-treatment methods. Samples containing either amyloid-like fibrils or spherulites produced from human insulin in acetic acid solutions are dependent on the presence of salt (NaCl). Moreover, mechanical shaking (600 rpm) inhibits spherulite formation, while only affecting the length of the formed fibrils compared to quiescent conditions. Besides shaking, the initial protein concentration in the formulation was found to control fibril length. Surprisingly, exchanging the solution used for aggregate formation to a physiologically relevant buffer, had a striking effect on the morphological integrity of the fibril and spherulite samples. Especially the secondary structure of one of our spherulite samples presented dramatic changes of the aggregated β-sheet content after exchanging the solution, emphasizing the importance of the aggregate stability. These results and considerations have profound implications on the data interpretation and should be implemented in the workflow for both fundamental characterization of aggregates as well as assays for evaluation of their corresponding biological effects.

Modifications of bacterial cellulose in wound care.

Wound infection may occur in acute and chronic wounds, wounds resulting from surgery or traffic accidents, and burns. Regardless of the extent and cause of the wound, prompt treatment is essential in reducing the patient's pain and limiting the spread of contamination. Improper wound care and associated chronic diseases may hinder the therapeutic success. Bacterial cellulose (BC) is highly biocompatible and has no cytotoxic effect on cells engaged in wound healing, such as fibroblasts and keratinocytes. Its high hydration level guarantees the maintenance of a moist wound environment. High mechanical strength, flexibility and resistance to damage make BC a promising material for dressings. Unfortunately, it does not display an inhibitory effect on bacterial growth. Introducing antimicrobial agents into the structure of BC has been a subject of many studies. This paper aims to present the latest reports on the possibility of the absorption of bacteriostatic and bactericidal agents in BC, such as metal particles, essential oils, antibiotics, antiseptics, and wound irrigation solutions. Moreover, the modifications in BC culture and post-production treatments in order to improve its physical properties are discussed.

The Open Cell Form of 3D-Printed Titanium Improves Osteconductive Properties and Adhesion Behavior of Dental Pulp Stem Cells.

Titanium specimens have been proven to be safe and effective biomaterials in terms of their osseo-integration. To improve the bioactivity and develop customized implants titanium, the surface can be modified with selective laser melting (SLM). Moreover, the design of macro-porous structures has become popular for reaching a durable bone fixation. 3D-printed titanium (Titanium A, B, and C), were cleaned using an organic acid treatment or with electrochemical polishing, and were characterized in terms of their surface morphology using scanning electron microscopy. Next, Dental Pulp Stem Cells (DPSCs) were cultured on titanium in order to analyze their biocompatibility, cell adhesion, and osteoconductive properties. All tested specimens were biocompatible, due to the time-dependent increase of DPSC proliferation paralleled by the decrease of LDH released. Furthermore, data highlighted that the open cell form with interconnected pores of titanium A, resembling the inner structure of the native bone, allows cells to better adhere inside the specimen, being proteins related to cell adherence highly expressed. Likewise, titanium A displays more suitable osteoconductive properties, being the profile of osteogenic markers improved compared to titanium B and C. The present work has demonstrated that the inner design and post-production treatments on titanium surfaces have a dynamic influence on DPSC behavior toward adhesion and osteogenic commitment.

Contaminants in biochar and suggested mitigation measures – a review

Biochars produced by pyrolysis at high temperatures under oxygen limited conditions can contain both well-known contaminants (polycyclic aromatic hydrocarbons (PAHs), potentially toxic elements (PTEs), dioxins, volatile organic compounds (VOCs)) and emerging contaminants (e.g., persistent free radicals, metal cyanide). Their potential to induce phytotoxicity, cytotoxicity, and neurotoxicity highlight the need to establish effective strategies to control and eliminate contaminants for sustainable biochar use. Although some articles have reviewed the ecotoxic potential of biochar in relation to some of these contaminants, strategies to mitigate the whole suite of contaminants potentially present in biochar have not been systematically reviewed so far. This review discusses (i) the formation mechanism of such contaminants and (ii) evaluates their potential risk to ecosystems, a prerequisite (iii) to understand and explore effective control strategies for producing biochars with minimum contamination. A pyrolysis unit design where pyrolysis liquids and solids are fully separated following the pyrolysis zone and optimization of pyrolysis parameters ensures organic contaminants in the pyrolysis liquids do not condense onto the biochar. Post-production treatments, such as thermal treatment or natural and artificial ageing help organic contaminant removal and breakdown. Co-pyrolysis of metal-rich feedstock with metal-free biomass is the only way of reducing total PTE levels, though available PTE levels are low in biochars and decrease further with pyrolysis temperature. More specific strategies for reducing the concentration of individual contaminants are discussed in the review. With our proposed recommendations, biochars with little risk for the environment can be produced.

Effect of Heat Treatment in Different Atmospheres on Thermally Evaporated ZnS films

In this study, the properties of ZnS films which can be used as a buffer layer in photovoltaic thin film solar cell technologies were tried to be improved by applying post-production heat treatments. ZnS films were subjected to annealing processes in Nitrogen, Argon and Air atmospheres with an atmosphere-controlled heat treatment system and the effects of these atmospheres on the films were investigated. As a result of XRD analysis, it was determined that all films show a preferential orientation towards the (111) ZnS plane. The crystallite size of the ZnS film increased with the applied heat treatment. It was also confirmed by transmittance measurements that the ZnS film annealed in air is partially oxidized and contains the secondary ZnO phase in its structure. Optical band gap values for ZnS films were found to be 3.53–3.56 eV. The refractive index values of the films were determined by spectroscopic ellipsometry. Two-probe technique was used to determine the electrical resistivity and heat treatment caused a decrease in the resistivity values of the films. Surface analyzes of the films were performed with the help of AFM and SEM measurements. As an outcome of this study, it has been revealed that the surfaces of ZnS films can be modified by heat treatment in Argon atmosphere. The production of ZnS films and their optimization with subsequent heat treatments were carried out, and ZnS films with high transmittance and improved morphology were obtained. These materials can be used as buffer layer or window layer in CZTS, CIGS and CdTe based solar cells.

Microstructure and Mechanical Properties of Ti-6Al-4V Manufactured by Selective Laser Melting after Stress Relieving, Hot Isostatic Pressing Treatment, and Post-Heat Treatment

Additive manufacturing (AM) is defined as a technology performed for tooling applications. It is used for manufacturing tools that have complex shapes and figures. In this study, an extensively applied Ti-6Al-4V alloy was made using the selective laser melting method. Post-production heat treatments were applied to decrease thermal stresses and to enhance the mechanical properties and the microstructure. The study investigates the fatigue mechanical properties, microstructure, hardness, and porosity of the AM Ti-6Al-4V after stress relieving (SR) and after SR followed by hot isostatic pressing (HIP). The samples’ upper and lower parts were independently examined to determine the effects of thermal conditions and the heat treatment of the microstructure. The microstructures were examined through optical microscopy, scanning electron microscopy and x-ray diffraction methods. The mechanical properties were investigated through microhardness testing, alongside assessment by fatigue testing at room temperature. The findings demonstrated that the microstructure after SR at 704 °C for 2 h is 100% fine martensitic α'-Ti, with a microhardness value of 408 HV. Air and furnace cooled samples have a more homogenous structure and are characterised by mixture (α + β) with microhardness values of 382 and 356 HV, respectively. After HIP at 920 °C and 100 MPa for 2 h was applied, the martensite was converted into a lamellar (α + β) microstructure, whereby the α phase is presented as fine needles situated among the β ridges in the microstructure, with the existence of the prior β grain boundary.

Ultra-High Vacuum characterization of Molybdenum-Carbide Graphite for HL-LHC collimators

In view of the High-Luminosity upgrade of the Large Hadron Collider (LHC) collimation system, a family of novel molybdenum-carbide graphite (MoGr) composites was developed to meet the challenging requirements of HL-LHC beam-halo collimation, in particular the electrical conductivity and thermo-mechanical performances. The Ultra-High Vacuum (UHV) behaviour of this material was extensively characterized to assess its compatibility with the accelerator’s specifications. The results presented in this paper correlate the outgassing behaviour with the microscopic features of MoGr compared to other graphite-based materials. Residual gas analysis (RGA) was exploited to optimize post-production treatments.

Neutron diffraction residual stress determinations in Fe3Al based iron aluminide components fabricated using wire-arc additive manufacturing (WAAM)

The Wire-Arc Additive Manufacturing (WAAM) process is an increasingly attractive method for producing porosity-free metal components. However, the residual stresses and distortions resulting from the WAAM process are major concerns as they not only influence the part tolerance but can also cause premature failure in the final component during service. The current paper presents a method for using neutron diffraction to measure residual stresses in Fe3Al intermetallic wall components that have been in-situ additively fabricated using the WAAM process with different post-production treatments. By using averaging methods during the experimental setup and data processing, more reliable residual stress results are obtained from the acquired neutron diffraction data. In addition, the present study indicates that the normal residual stresses are significant compared to normal butt/fillet welding samples, which is caused by the large temperature gradient in this direction during the additive layer depositions.

A comparative study on pre- and post-production plasma treatments of PCL films and nanofibers for improved cell-material interactions

In this work, an atmospheric pressure plasma jet (APPJ) has been used to modify a 5% polycaprolactone (PCL) solution, after which the PCL solution was spin coated or electrospun to generate PCL films and nanofibers respectively. The APPJ treatment was found to have no effects on the chemical and physical properties of the PCL films, however, a strong influence on the morphology of electrospun PCL nanofibers could be observed. PCL nanofibers generated from the pristine PCL solutions contained multiple beads, while the PCL nanofibrous material generated from the APPJ-treated solutions consisted of nicely elongated, beadless PCL nanofibers. This enhanced electrospinnability was attributed to the strongly increased solution conductivity induced by the APPJ exposure. The APPJ treatment was also found to have minor effects on the chemical composition and the wettability of the nanofibers, which could be linked to the different surface morphology. All investigated pristine and APPJ-treated films and nanofibers unfortunately possessed poor cell-material interactions as a result of their high hydrophobicity. To cope with this issue, after spin coating and electrospinning, a second surface modification treatment making use of a dielectric barrier discharge (DBD) sustained in argon was also conducted. These treatments were found to considerably increase the wettability of PCL films and nanofibers without affecting their surface morphology. The enhanced wettability was caused by the incorporation of CO functional surface groups by the performed DBD treatments. The treatments were also found to positively affect cell growth on PCL films and nanofibers, with the best cellular performance obtained for the APPJ/DBD-treated PCL nanofibers. A combination of plasma treatments can thus play a significant role in the preparation of ideal electrospun PCL scaffolds for tissue engineering applications.

Laser Powder Bed Fusion: tailoring the microstructure of alloys for biomedical applications

Abstract Additive manufacturing (AM) is particularly attractive for biomedical applications, where complex geometries and a high degree of individualization are required. Laser powder bed fusion (LPBF) is an AM technology exploiting the action of a solid-state laser to locally melt a metal powder according to a computer aided design (CAD) model. In the present study, the EOS Cobalt Chrome SP2 (Co-Cr-Mo-W) and Ti64 (Ti6Al4V) powders were sintered by the system equipped with a Yb fiber laser. During LPBF, the Co-Cr-Mo-W metal powder undergoes total melting followed by rapid cooling, giving rise to athermal martensitic phase transformation from the high-temperature γ (fcc) phase to the low-temperature e (hcp) phase. This produces an intricate network of thin e-lamellae inside the γ phase matrix. After the firing cycle this structure is maintained, and a massive presence of coarse precipitates is also observed. Owing to the rapid cooling taking place during LPBF, in Ti6Al4V sintered samples only the acicular martensitic α’ phase is present. The firing cycle induces the β phase formation at the α plate boundaries and this microstructure leads to reduced values of strength, with respect to those of the as-sintered samples. The highlighted behaviors show that by tuning the post-production heat treatments it is possible to tailor the microstructure and the mechanical properties.

Expeller Barrel Dry Heat and Moist Heat Pressure Duration Induce Changes in Canola Meal Protein for Ruminant Utilisation.

Simple SummaryCanola meal, a by-product of oil production from canola seed, is a source of protein commonly incorporated into dairy and feedlot rations. Processing conditions and pressure treatments can alter the quality of protein in canola meal. In this study, the impact of expeller dry heat and moist heat pressure duration time on general nutritional properties, in vitro protein degradability, Maillard reaction product formation, and molecular and microscopic structural characteristics of canola meal were investigated. Increased dry heat temperature rapidly increased digestible protein and non-protein nitrogen content, and constricted amide II secondary structure. Increased moist heat pressure treatment duration promoted browning, and the conversion of protein to more intermediately and slowly degradable forms. Dry heat and moist heat pressure affected meal protein solubility and protein and lipid-related functional groups. Moist heat pressure fragmented canola meal into enzyme-resistant aggregates with crevices containing oil bodies. Induced changes may impact the supply of protein and amino acids and subsequently the yield and composition (protein and lipid) of milk produced by dairy cows. These findings benefit producers of canola meal by further describing the effects of processing and treatment conditions on protein characteristics, particularly those which affect the production potential of ruminants fed canola meal as a source of protein.To improve the protein nutritional quality of canola (Brassica napus L.) meal, further investigation of the effects of processing conditions and post-production treatments is desirable. The impact of barrel dry heat temperature (20 °C (cold press) and 100 °C (expeller)) and moist heat pressure (MHP) duration time on general nutritional properties, Maillard reaction product (MRP) formation, in vitro protein degradability, and molecular and microscopic structural characteristics of canola meals were investigated. Increased MHP duration reduced (p < 0.05) dry matter, soluble protein, rapidly degradable protein, yellowness (early MRP), whiteness (late MRPs), absorbance at 294 nm (intermediate MRPs), and amide I; and increased (p < 0.05) non-protein N, neutral detergent fibre, neutral detergent insoluble crude protein (CP), intermediately and slowly degradable protein, in vitro effective CP degradability, redness, degree of colour change, and browning. Increased dry heat temperature reduced (p < 0.01) CP and rapidly degradable protein, constricted amide II, reduced (p < 0.05) protein solubility in 0.5% KOH and increased (p < 0.05) acid-detergent fibre and intermediate MRPs. Browning index and redness exhibited potential as rapid indicators of effective CP degradability and soluble protein, respectively. Dry heat and MHP altered (p < 0.05) lipid-related functional groups. Dry heat affected napin solubility, and MHP altered cruciferin and napin solubility. Application of MHP induced the formation of proteolysis-resistant protein aggregates with crevices containing oil bodies. Induced changes may impact the supply of proteins and amino acids and subsequently the yield and composition (protein and lipid) of milk produced by dairy cows.

The influence of post-production heat treatment on the multi-directional properties of nickel-aluminum bronze alloy fabricated using wire-arc additive manufacturing process

In this paper, a nickel-aluminum bronze alloy component is built using wire-arc additive manufacturing process. In order to investigate the influence of anisotropy introduced by the wire-arc additive manufacturing process, the layer-by-layer manufactured components with different post-production heat treatments are characterized by optical and scanning electron microscopy morphologies, X-ray diffraction and mechanical tests in longitudinal, transverse and normal directions. The experimental results show that the deposit exhibits higher strengths in the longitudinal and transverse direction than in the normal direction. Also, the ductility of the alloy is significantly improved with the designed quenching and tempering method, and competitive mechanical properties are achieved when tempering temperature reaches 650 °C. In addition, the anisotropy in the additively manufactured alloy can be effectively modified by the quenching and tempering heat treatments.

Designing for Multiple Expressions: Questioning Permanence as a Sign of Quality in Textiles

Developing alternative materials and methods of production and recycling is crucial to achieving more sustainable, circular textile practices. In addition to these, a shift in how textiles are perceived may well be needed. Textile practice has long sought to create textiles that, regardless of their material or post-production treatments do not subsequently change in expression, eliminating the fading of colors and wearing out of materials. Questioning this in order to evaluate quality, durability, and aesthetics may open up for greater circularity through extending product lifetimes, and allowing change to be embraced rather than delaying the signs of aging. This paper presents work that challenges the notion of permanence as a sign of quality in textiles by shifting the focus towards creating textiles that are capable of developing different visual expressions over time. By examining the natural changes in color of materials in plain and Jacquard-patterned woven textiles made of several materials, this paper explores the possibilities relating to designing textile patterns that can evolve in multiple different directions from one starting point. Textiles woven with a combination of different materials were used in various contexts, including outdoors, in order to explore how the materials reacted. The resulting color combinations varied depending on what conditions the material was exposed to, suggesting a more versatile view on the aesthetics of textiles. The results indicate that various colors, patterns, and structures can be achieved from one starting point, indicating that an alternative definition for quality, based on the aesthetics of change, may be viable. The natural aging of materials could be used in design processes to embed evolving patterns, colors, or structures in textiles, reconnecting textile products with the inherent, changeable qualities of materials.

Observation of Magnetic Radial Vortex Nucleation in a Multilayer Stack with Tunable Anisotropy

Recently discovered exotic magnetic configurations, namely magnetic solitons appearing in the presence of bulk or interfacial Dzyaloshinskii-Moriya Interaction (i-DMI), have excited scientists to explore their potential applications in emerging spintronic technologies such as race-track magnetic memory, spin logic, radio frequency nano-oscillators and sensors. Such studies are motivated by their foreseeable advantages over conventional micro-magnetic structures due to their small size, topological stability and easy spin-torque driven manipulation with much lower threshold current densities giving way to improved storage capacity, and faster operation with efficient use of energy. In this work, we show that in the presence of i-DMI in Pt/CoFeB/Ti multilayers by tuning the magnetic anisotropy (both in-plane and perpendicular-to-plane) via interface engineering and postproduction treatments, we can stabilize a variety of magnetic configurations such as Néel skyrmions, horseshoes and most importantly, the recently predicted isolated radial vortices at room temperature and under zero bias field. Especially, the radial vortex state with its absolute convergence to or divergence from a single point can potentially offer exciting new applications such as particle trapping/detrapping in addition to magnetoresistive memories with efficient switching, where the radial vortex state can act as a source of spin-polarized current with radial polarization.