Polymer Dispersed Liquid Crystal Research Articles

A Smart Window with Passive Radiative Cooling and Switchable Near-Infrared Light Transmittance via Molecular Engineering.

Smart windows with synergetic light modulation have heightened demands for applications in smart cars and novel buildings. However, improving the on-demand energy-saving efficiency is quite challenging due to the difficulty of modulating sunlight with a broad bandwidth in an energy-saving way. Herein, a smart window with switchable near-infrared light transmittance and passive radiative cooling is prepared via a monomer design strategy and photoinduced polymerization. The effects of hydrogen bonds and fluorine groups in acrylate monomers on the electro-optical properties as well as microstructures of polymer-dispersed liquid crystal films have been systematically studied. Some films show a high contrast ratio of 90.4 or a low threshold voltage (Vth) of 2.0 V, which can be roll-to-roll processed in a large area. Besides, the film has a superior indoor temperature regulation ability due to its passive radiative cooling and controllable near-infrared light transmittance properties. Its radiative cooling efficiency is calculated to be 142.69 W/m2 and NIR transmittance could be switched to below 10%. The introduction of a carboxylic monomer and fluorinated monomer into the system endows the film with a highly efficient temperature management capability. The film has great potential for applications in fields such as flexible smart windows, camouflage materials, and so on.

Intelligent switchable nanomaterials doped optical switches with PDLC-PVA-PSCLC bilayer liquid crystal structure for smart windows

ABSTRACT Due to the ability to switch between transparent and light scattering states, polymer dispersed liquid crystals (PDLC) and polymer stabilised cholesteric liquid crystals (PSCLC) are widely used in smart windows and flexible displays. A novel double-layer optical switch fabricated from a PDLC-PVA-PSCLC structure has been developed in this study, and the optimal formulation of each layer of the structure was investigated. In addition, the effect of adding (spin-coating) nanoparticles on overall switch performance was investigated. The double-layer switch under optimal conditions achieved 89.1% UV shielding, which also possessed excellent layer-by-layer driving performance and was able to modulate the UV shielding rate according to the voltage, with a tunable range of 74.83%-94.33%. Consequently, this optical device holds great promise for significant improvement and application in smart windows and flexible displays.

Use of polymer dispersed liquid crystal (PDLC) film as a greenhouse cover material

Use of polymer dispersed liquid crystal (PDLC) film as a greenhouse cover material

Annual Energy-Saving Smart Windows with Actively Controllable Passive Radiative Cooling and Multimode Heating Regulation.

Smart windows with radiative heat management capability using the sun and outer space as zero-energy thermodynamic resources have gained prominence, demonstrating a minimum carbon footprint. However, realizing on-demand thermal management throughout all seasons while reducing fossil energy consumption remains a formidable challenge. Herein, an energy-efficient smart window that enables actively tunable passive radiative cooling (PRC) and multimode heating regulation is demonstrated by integrating the emission-enhanced polymer-dispersed liquid crystal (SiO2@PRC PDLC) film and a low-emission layer deposited with carbon nanotubes. Specifically, this device can achieve a temperature close to the chamber interior ambient under solar irradiance of 700W m-2, as well as a temperature drop of 2.3°C at sunlight of 500W m-2, whose multistage PRC efficiency can be rapidly adjusted by a moderate voltage. Meanwhile, synchronous cooperation of passive radiative heating, solar heating, and electric heating endows this smart window with the capability to handle complicated heating situations during cold weather. Energy simulation reveals the substantial superiority of this device in energy savings compared with single-layer SiO2@PRC PDLC, normal glass, and commercial low-E glass when applied in different climate zones. This work provides a feasible pathway for year-round thermal management, presenting a huge potential in energy-saving applications. This article is protected by copyright. All rights reserved.

Optimization of transparent conductive properties of magnetron sputtered Sb-doped SnO2 films by RF power: Towards application in polymer-dispersed liquid crystal (PDLC) films

Sb-doped SnO2 (ATO) films were prepared with different RF powers (PRF) under two O2 flow rates (FO2) by magnetron sputtering, and then subjected to rapid thermal annealing (RTA) treatment. The effects of PRF, FO2, and RTA on the crystallinity, stress, surface morphology, conductive properties, transmittance in visible-light range (TVis), and energy gap (Eg) of the films were investigated. As the PRF increases, the film crystallinity improves or first improves and then slightly degrades, and the compressive stress decreases. With increasing PRF, the surface changes from textured to granular morphology and from granular to honeycomb-like morphology under two FO2, respectively. Meanwhile, the conductive properties first enhance and then degrade, and the TVis and Eg tend to decrease, especially at higher PRF. Basically, the films prepared with higher FO2 have lower compressive stress, inferior conductive properties, and larger TVis and Eg compared with the films prepared with lower FO2. After RTA, the film crystallinity obviously improves, the compressive stress transforms into tensile stress, and the surface morphology has not undergone significant changes. Meanwhile, the conductive properties significantly enhance and Eg obviously increases. The TVis of the films prepared with lower FO2 can be increased by RTA. The influence mechanisms of the above factors on the structure and optoelectronic properties of the ATO films were explored, and ultimately, the ATO films have the TVis of 76.35–80.86%, sheet resistance of 51.7–91.9 Ω/sq., and quality factor of 1.03–1.67 × 10−3 Ω−1 within the optimized PRF range. Polymer-dispersed liquid crystal (PDLC) films were fabricated using optimized performance ATO films as electrodes, and their on-state transmittance, off-state transmittance, threshold electric field, and saturation electric field were 2.08–4.61%, 61.69–68.56%, 0.656–0.796 V/μm, and 1.68–2.108 V/μm, respectively. The current results indicate the potential application of ATO films in PDLC films as electrode.

A novel dual-functional flexible dimming film for smart window applications: Energy saving and self-cleaning performance

Polymer dispersed liquid crystal (PDLC) is a promising candidate for electrically controlled smart window applications because of its energy efficiency, convenience and other advantages. However, its flexibility and heat management capabilities are not effectively evaluated. Herein, a flexible dual-functional intelligent window based on PDLC composite is designed for this purpose, which integrates Ag nanowires as a transparent conductive electrode (TCE) and Tm3+/Yb3+-CsxWO3 (Tm3+/Yb3+-CWO) as a near-infrared shielding and air purification layer. Specifically, the as-made smart window can control the transmission of both visible and near-infrared light. Furtherly, it also possesses self-cleaning capability. A series of characterization has been carried out. The resistance of the Ag nanowire layer is measured to be 22.47 Ω/sq and the transmittance reaches 78.8 %. Flexibility test shows that when the bending radius is 4 mm, the resistance value of the TCE changes only 6 % after 500 repetitions, indicating good flexibility and stability. The spectrum examination reveals that the near-infrared light shielding efficiency achieves 80 % and the average transmittance of visible light is 76.7 %. The degradation of Rhodamine B (RhB) is used to evaluate the purification performance and result shows that the degradation percentage reaches 70 % in 120 min. Heat-regulation simulation test discloses that the indoor temperature can be decreased by 10 °C. Compared to traditional PDLC windows, the designed flexible window has broader application prospects in areas of architecture, vehicle glass, military stealth materials and so on.

Study on polymer dispersed liquid crystal films with wide viewing angle

ABSTRACT Polymer Dispersed Liquid Crystal (PDLC) films have been widely used as electronically controlled dimming technology, and solving the problem of narrow angle of PDLC is a cutting-edge challenge for their application. In this paper, a theoretical model of the viewing angle characteristics of PDLC is constructed, and the corresponding samples are experimentally fabricated. It is found that the simulation results of transmittance changing with the viewing angle are in good agreement with the experimental results. Furthermore, the technical approaches to improve PDLC viewing angle characteristics and achieve a wide viewing angle are discussed theoretically. The results show that the PDLC films for wide viewing angle can be obtained by using liquid crystal materials with smaller anisotropy of refractive index and polymer materials with refractive index slightly higher than the ordinary refractive index of liquid crystal.

Preparation of a double-layer liquid crystal optical shutter with fluorescent properties and its ultraviolet shielding screening properties

ABSTRACT Polymer dispersed liquid crystal (PDLC) films and polymer-stabilised cholesteric liquid crystals (PSCLC) films have been widely applied in smart optoelectronics due to electrical switching properties. In this study, fluorescent dyes were introduced into PDLC films and combined with PSCLC films to invent a new type of optical shutter, and the optimal formulations of each of liquid crystal structural layers were investigated. Then, PDLC anti-counterfeit optical device doped with fluorescent materials were fabricated by UV curing method using polymerisation-induced phase separation. The novel optical shutter could be driven layer by layer at room temperature according to different voltages to realise the switching of three states, namely, off state, PDLC layer-driven, and full-driven (open state). Samples under optimal conditions showed that the new optical shutter could achieve 96.5% UV shielding in the off state and had a long lifetime. The results demonstrate the attractive potential of the new optical shutter for optoelectronic devices and smart curtain applications.

Reduced driving electric field of ionic salt doped nano-structured polymer dispersed liquid crystals device

The nano-structured polymer dispersed liquid crystal (NPDLC) possesses several intriguing properties due to its nano-confined structure and unprecedented flexibility. However, the involved polymer networks necessitate a higher operating field which deteriorates the device's feasibility for real-device applications. Here, we demonstrate a simple technique to reduce the driving field by introducing a small amount of ionic salt into the NPDLC. The selective occupation of ionic salt during the phase separation reduces the interfacial energy of LC molecules, dipping by 40 % (3.6 V/µm) of the driving electric field. The electrohydrodynamic instability created by localized ion transportation led to reduced LC anchoring strength at the polymer interface at which the operating field was reduced. Our design is versatile and a potential alternative to the present NPDLC.

Voltage‐Driven Molecular Orientation with Optical Synergy in Rare Earth Doped Polymer Dispersed Liquid Crystals

AbstractAchieving reversible large‐span photoluminescence regulation still faces difficulties due to limitations in the design or preparation conditions of related materials. Herein, a universal strategy that combines voltage‐driven molecular orientation with optical synergy between rare earth (RE) doped materials and polymer dispersed liquid crystals (PDLC) is proposed to achieve large‐span reversible opto‐electrically synergistic induced multi‐response photoluminescence regulation. The obtained Eu(tta)3phen/PDLC composites can exhibit different emission colors reversible transform from purple to purplish‐pink depending on the excitation wavelength and the applied electric voltage. The interaction between PDLC and Eu(tta)3phen is analyzed and the field distribution of internal microstructures is simulated using the finite‐difference time‐domain method, providing a theoretical basis for the voltage‐dependent photon interactions. The potential applications of Eu(tta)3phen/PDLC composites for anticounterfeiting is suggested by demonstrating a proof‐of‐concept anticounterfeiting system based on the composites. The strategy of opto‐electrically synergistic induced multi‐response photoluminescence regulation, with general applicability, can be easily extended to other RE doped materials and PDLC systems, opening up new possibilities for photoluminescence regulation research.

Preparation and Characterization of Bilayer Polymer-Dispersed Liquid Crystals Doped with Gd2O3 Nanoparticles and Rhodamine B Base Fluorescent Dye.

Using the polymerization-induced phase separation (PIPS) method, bilayer polymer-dispersed liquid crystal (PDLC) films with a PDLC-PVA-PDLC structure were prepared in this work. It was found that all PDLC performance indexes were affected by polymer mesh size after comparing the microscopic morphology and electro-optical properties of samples with different monomer ratios. Gd2O3 nanoparticles and rhodamine B base fluorescent dyes introduced into the bilayer PDLC optimized the samples' electro-optical properties and developed new functionalities. In addition, the bilayer PDLC doped with Gd2O3 and rhodamine B base held excellent progressive driving functions as well as stable durability properties. Samples doped with Gd2O3 nanoparticles and rhodamine B base also produced excellent anti-counterfeiting effects under UV irradiation at different angles, further exploiting the application potential of PDLC.

Polymer-dispersed liquid crystal with low driving voltage utilising reaction selectivity of two-stage polymerisation

ABSTRACT An optimised approach is presented in this study for the fabrication of a polymer-dispersed liquid crystal (PDLC) device with a low driving voltage and high contrast ratio (CR). This method involves a two-step process utilising Michael addition and radical polymerisation, employing a reaction-selective orthogonal photoinitiated system. The impact of incorporating low surface energy monomers on PDLC performance is thoroughly investigated, and the driving voltage is further reduced through selective reaction-induced interface modification. The polymer morphology can be finely tuned by adjusting the thiol content, leading to various PDLC properties. This paper introduces a novel surface modification technique within the polymer-liquid crystal system, presenting a fresh perspective on regulating PDLC performance. By choosing monomer structures, the sequence of reactions can be precisely controlled, allowing for the introduction of structural units with distinct functionalities at the polymer interface. This approach facilitates interfacial functionalization and enables the design of multi-layer structures for synthetic polymers, realising innovative functionalities.

Preparation and Application of Polymer-Dispersed Liquid Crystal Film with Step-Driven Display Capability.

The realization of multifunctional advanced displays with better electro-optical properties is especially crucial at present. However, conventional integral full drive-based transparent display is increasingly failing to meet the demands of the day. Herein, partitioned polymerization as a novel preparation method was introduced innovatively into polymer-dispersed liquid crystals (PDLC) for realizing a step-driven display in agreement with fluorescent dye to solve the above drawback. At first, the utilization of fluorescent dye to endow the PDLC film with fluorescent properties resulted in a reduction in the saturation voltage of the PDLC from 39.7 V to 25.5 V and an increase in the contrast ratio from 58.4 to 96.6. Meanwhile, the experimental observations and theoretical considerations have elucidated that variation in microscopic pore size can significantly influence the electro-optical behavior of PDLC. Then, the step-driven PDLC film was fabricated through the exposure of different regions of the LC cell to different UV-light intensities, resulting in stepwise voltage-transmittance (V-T) responses of the PDLC film for the corresponding regions. Consequently, under appropriate driving voltages, the PDLC can realize three different states of total scattering, semi-transparent and total transparent, respectively. In addition, the PDLC film also embodied an outstanding anti-aging property and UV-shielding performance, which makes it fascinating for multifunctional advanced display applications.

The regulation of electro-optical properties and polymer morphology of polymer-dispersed liquid crystal films with silicon nanostructure

ABSTRACT In this work, the thiol modified silica nanostructures (SiO2-SH) were doped into polymer-dispersed liquid crystal (PDLC) films. The SEM was used to observe the morphology of the polymer microstructure. The electro-optical (E-O) property test was determined by a liquid crystal parameter tester. The SEM images suggested that the SiO2-SH nanoparticles can react with acrylate groups to form the polymer matrix. The saturation voltage decreased by half in the sample when the dosage of the SiO2-SH nanoparticles was 7.5 wt%, which may be due to the reduced anchoring strength of the polymer matrix incorporated with silicon nanoparticles resulting from the lower surface energy and the enhanced steric repulsions of LC droplets and polymer matrix. In addition, the preparation conditions like polymerisation temperatures and UV light intensity also effectively regulated the E-O properties and polymer microstructure of the PDLC film with silica nanostructure. Thus, the results showed that the E-O properties and the polymer morphology of PDLC films with silicon nanostructures can be effectively regulated by doping SiO2-SH nanoparticles and regulating the preparation conditions such as the polymerisation temperature and UV light intensity. This work can provide practical guidance for modulating the properties of PDLC films.

Effects of hydroxylated acrylates on electro-optical performance and adhesion strength of polymer dispersed liquid crystal films

In this study, effects of hydroxylated acrylate monomers that includes both monoacrylate and diacrylate on properties of the as-made polymer dispersed liquid crystal (PDLC) films are explored. The electro-optical response, microstructure and adhesion strength are characterized to compare the influences in detail. It is revealed that hydroxylated acrylate monomers can significantly enhance the adhesion strength in comparison with the non-hydroxylated monomer. Moreover, the hydroxyl group can alter the microstructure of the polymer matrix by affecting the polymerization and phase separation process. Thereby, the electro-optical response of the PDLC film is affected. Additionally, the influences are closely related to the position and concentration of hydroxyl group in acrylate monomers. When the hydroxyl group is located in the α-position or is distant from the reactive site, the improvement is limited. Increasing the concentration of hydroxyl groups by introducing monomers containing multiple hydroxyl groups in one molecule or combining hydroxylated monoacrylate and hydroxylated diacrylate monomers can change the microstructure type and deteriorate the electro-optical performance. By carefully balancing these factors, an optimized PDLC film can be obtained, whose adhesion strength is elevated to about 2.3 times that of the non-hydroxylated film and contrast ratio is improved from 135 to 262. This work is anticipated to provide deeper insights into the role of hydroxylated monomers and offer more possibilities to improve the overall performance of the PDLC films.

Thermomechanical response of liquid crystal elastomers: role of crosslinker density

In this work thermomechanical properties of main-chain liquid crystal elastomers (MC-LCEs) with different degrees of crosslinking were investigated, and gradual loss of thermomechanical response was observed on repetitive measurements. Specifically, six samples of MC-LCEs were prepared, with crosslinker-to-mesogen relative concentration ranging from 5% to 10% in steps of 1%. The obtained results were then compared to thermomechanical response of side-chain liquid crystal elastomers (SC-LCEs). Additionally, thermomechanical response of polymer dispersed main-chain liquid crystal elastomers (MC-PDLCEs) was investigated. Results indicate that in MC-LCEs the concentration of crosslinker defines thermomechanical response and affects stability of the system. The loss of thermomechanical response is negligible in the case of crosslinker to mesogen ratio being the smallest, namely in 5% sample, and it is unaffected by glasslike to nematic phase transition. SC-LCEs do not show any sign of such behaviour and remain stable after several cycles of thermomechanical measurements.

Influence of Ionic Conductivity in Polymer Dispersed Antiferroelectric Liquid Crystals (PDAFLC): A Comparison of Critical Fields

Theoretically critical unwinding field was studied using Landau free energy model of three different geometrical configuration of antiferroelectric liquid crystals. In this study, we considered the influence of ionic conductivity both in pure antiferroelectric liquid crystals and polymer dispersed antiferroelectric liquid crystals. We observed that the modified elastic constant which accounted for the interaction of ionic conductivity and polymer cross-linked chains is very much responsible for the variation of critical field.

Biowaste-based porous carbon nanoparticle doped polymer dispersed ferroelectric liquid crystal composites: an impact on optical and electrical properties

Bio-waste-based porous carbon nanoparticles (PCNPs) were synthesized using green synthesis and investigated their doping effect on the optical and electrical properties of polymer-dispersed ferroelectric liquid crystals (PDFLCs) composites. Here we employed the polymerization-induced phase separation (PIPS) approach for constructing the PDFLCs. Our results indicate that the dispersion of PCNPs into the PDFLC material results in an alteration to several physical parameters, including morphology, dielectric permittivity, conductivity and optical band gap. A decrease in the ac conductivity of the doped samples was seen. Additionally, UV-Visible study reveals that inclusion of PCNPs resulted in a decrease in the optical band gap of PDFLC, with a value of approximately 3.1 eV. These findings demonstrate the potential of using PCNPs as dopants in PDFLCs for various applications, including sensing, energy storage and optoelectronics.

Preparation of Progressive Driving Bilayer Polymer-Dispersed Liquid Crystals Possessing a PDLC-PVA-PDLC Structure.

In this paper, the bilayer polymer-dispersed liquid crystals possessing a PDLC-PVA-PDLC structure were prepared by integrating two monolayer PDLCs. The effect of the polymer mesh size on the electro-optical properties of a bilayer PDLC was investigated by comparing the micro-morphology and electro-optical curves under different polymerization conditions. In addition, the impact of doping MoO2 nanoparticles with surface modification on the comprehensive performance of the bilayer PDLC was further researched. The contrast ratio of the bilayer PDLC prepared under the optimal conditions was improved by more than 90% and still maintained excellent progressive driving performance. Therefore, the development of a bilayer PDLC with optimal electro-optical properties will significantly enhance the technological prospects for the application of PDLC-based devices in smart windows, displays, and flexible devices.

Holographic multiplane augmented reality head-up display with switchable display modes based on polymer dispersed liquid crystal.

The multiplane augmented reality (AR) head-up display (HUD) is important in improving driving safety and comfort. In this paper, we propose an AR-HUD with switchable display modes based on polymer dispersed liquid crystal (PDLC) and lens holographic optical elements (HOEs), which can provide two display modes: the dual-virtual-image mode and the virtual-real-image mode. The dual-virtual-image mode can produce two virtual images at different depths, which can provide a better sense of reality integration for the driver to improve driving safety and comfort. The virtual-real-image mode can produce one far virtual image and one near real image at different depths, and it provides a larger eye box (EB) for both driver and passengers in the car and a higher image contrast. The two display modes can be switched by an electronically controlled scattering module consisting of a pair of PDLC films. The proposed AR-HUD system is compact and equipped with multiplane display and mode-switching functions, and is expected to be applied in the future.