Polyethylene Terephthalate Bottles Research Articles

Ammonia-Borane Dependent Transfer Hydrogenation of Carboxylic Esters to Primary Alcohols.

Here, we present a user-friendly protocol that uses bench-stable NH3·BH3 (AB) as the hydrogen transfer agent for the reduction of both aromatic and aliphatic esters without an external catalyst and base, delivering a structurally diverse array of primary alcohols (80-98% yields). The broad functional-group tolerance (halogen, boronic ester, -NO2, -OH, etc.) under environmentally acceptable conditions implies high practical utility. Further, a tandem catalytic conversion of a plastic waste polyethylene terephthalate (PET) bottle to 1,4-benzenedimethanol including fatty esters into respective fatty alcohols was shown.

Waste PET bottles derived carbon black as electrode material for supercapacitor application

This study explores the conversion of polyethylene terephthalate (PET) waste into carbon black for its use in supercapacitors, offering a sustainable solution to waste management and energy storage needs. PET bottles were pyrolysed in an inert environment to produce carbon black. This plastic waste derived carbon was then characterised and used for electrode fabrication to explore its potential in supercapacitor applications. The supercapacitive properties of these electrodes were evaluated using cyclic voltammetry and charge–discharge techniques in various “Water-in-salt” electrolytes (WIS). WIS are the electrolytes in which the concentration of water is less than the concentration of salts by weight and volume. electrolytes. Sodium acetate (CH3COONa) exhibited the highest potential window and specific capacitance among the tested electrolytes. The derived carbon black demonstrated promising electrochemical performance, with a specific capacitance of 233 F/g and an energy density of 186.6 Wh/kg. These findings underscore the potential of carbon black derived from waste PET bottles as an effective material for supercapacitors, contributing to sustainable energy storage solutions and waste reduction.

Release Characteristics of Small-Sized Microplastics in Bottled Drinks Using Flow Cytometry Sorting and Nile Red Staining

Small-sized microplastics (MPs) pose concerns about potential risks to both the environment and human health. However, research on MP pollution is hampered by limitations in the detection techniques. Also, few studies have provided insight into the release of small-sized MPs from disposable polyethylene terephthalate (PET)-bottled drinks for outdoor usage. Thus, PET bottles’ potential to release small MPs sized 1–100 μm outdoors was studied in relation to physical and chemical parameters (temperature, sunlight irradiation, and drink characteristics) using flow cytometry and Nile Red dye. The results showed that temperatures below 80 °C had little effect on the release of MPs from PET bottles. Sunlight irradiation and alkalinity were prone to promote the generation of MPs, mostly 1–5 μm in size. Moreover, the combined impact test implied that two pairings—acidity with temperature and alkalinity with sunlight—positively affected MP release, with maximum releases of 21,622 ± 2477 particles/L and 31,081 ± 7173 particles/L, respectively. Based on the rapid quantification of small-sized MPs using flow cytometry after Nile Red selection, the results hereby presented will assist researchers in reducing MP release and aid them in the evaluation of MPs’ contamination of aquatic environments.

Production of thermostable recombinant cutinase using mixed food waste: A sustainable approach toward environmental remediation

Recently, there has been a significant surge in the utilization of single-use plastics. Cost-effective degradation of plastics is imperative to reduce the ecological burden. This study explores the overproduction and characterization of PET (Polyethylene terephthalate), a degrading enzyme cutinase in the E. coli BL21 (DE3) expression system. Furthermore, this research delves into the utilization of mixed food waste (MFW) as a sustainable substrate for the production of Cutinase, replacing commercial glucose. The newly isolated strain, Aspergillus terreus, showed the highest glucoamylase activity of 76.10 ± 3.10 U/g. The enzymatic hydrolysis of mixed food waste resulted in 50 ± 0.4 g/L of glucose, used as feedstock for cutinase production. The crude enzyme activity was evaluated to be 11.64 U/mg, and a further 14.11-fold purification was achieved through IMAC. The purified recombinant enzyme showed its maximum activity at 70℃ and pH 7. The metal ion Na+ increased the enzyme activity by 26 % while Zn+2 significantly inhibited the same (47 % inhibition); other ions had little or no effect. Taguchi’s optimization of five variables showed that the concentration of food waste hydrolysate has the maximum impact on enzyme production. The treatment of commercially available PET bottles using the purified enzyme showed characterizable surface degradation effects. This is the first time food waste hydrolysate was used as a sole carbon source to produce recombinant cutinase. This approach can potentially pave the way for sustainable biorefinery and waste management.

Evaluating strategies to increase PET bottle recycling in the United States

AbstractIn the United States, polyethylene terephthalate (PET) bottle collection rates have not increased in a decade. Recycling rates remain abysmal while industry commitments and policy targets escalate the demand for recycled plastics. We investigate the PET bottle recycling system, where collection is a critical bottleneck and recycled PET supply is not meeting the expected demand. We characterize demand for recycled PET (R‐PET), analyze scenarios of expanding deposit return systems (DRS), and quantify cost barriers to improving PET bottle recycling. We find that a nation‐wide DRS can increase PET bottle recycling rates from 24% to 82%, supplying approximately 2700 kt of recycled PET annually. With stability in demand, we estimate that this PET bottle recycling system can achieve 65% bottle‐to‐bottle circularity, at a net cost of 360 USD/tonne of PET recycled. We also discuss environmental impacts, stakeholder implications, producer responsibility, and complimentary policies toward an efficient and effective recycling system.

Praseodymium orthovanadate-waste PET bottle derived sulfur doped carbon for efficient Z-scheme photocatalytic CO2 reduction

Escalating amounts of carbon dioxide (CO2) in the Earth's atmosphere are a major cause of climate change and its negative consequences, making it a global concern. The present work highlights the intersection of waste management, resource utilization, and climate change mitigation, showcasing the potential for an additional sustainable and circular economy. Synthesizing carbon from waste polyethylene terephthalate (PET) bottles is an eco-friendly approach. X-ray diffraction, Raman spectroscopic, scanning electron microscopic, tunnelling electron microscopic, infrared fourier transform spectroscopy (FTIR) and X-ray photoelectron spectroscopic results indicate the effective extraction of carbon doped with sulfur (S@C) and the successive formation of nanocomposite with PrVO4 (PrV/S@C). Superior photocatalytic activity was observed under visible light compared to UV light. PrV/S@C showed enhanced light-driven CO2 reduction compared to pristine materials and was found to evolve 39, 56, and 98 µmol h−1 g−1 of H2, CH4 and CO, respectively. The effect of reaction temperature was examined and optimized at 100 °C. The enhanced activity in PrV/S@C compared to PrV and S@C probably due to the increased surface area, conductivity and synergy. In-Situ Diffused reflectance (DRIFT-IR) and liquid chromatography mass spectroscopy (LC-MS) confirm the evolution of CO and CH4. The optical, photo/electrochemical, Scavenger studies, Electron spin resonance (ESR) and Mott-Schottky studies suggest the formation of a direct Z-scheme photoredox reaction in the presence of PrV/S@C and sacrificial gent. The reusability studies for 5 cycles indicate good stability with a slight deviation in structure and morphology of PrV/S@C, as observed in XRD and SEM. Tackling plastic pollution and generating value-added carbonaceous products through CO2 reduction is the twin application of the present work that has piqued the interest of several researchers in environmental remediation.

Electrocatalytic Upgrading of Plastic and Biomass-Derived Polyols to Formamide under Ambient Conditions.

Electrocatalytic upgrading of wasted plastic and renewable biomass represents a sustainable method to produce chemicals but is limited to carbohydrates, leaving other value-added chemicals, such as organonitrogen compounds, being scarcely explored. Herein, we reported an electrocatalytic oxidation strategy to transform polyethylene terephthalate (PET) plastic-derived ethylene glycol (EG) and biomass-derived polyols into formamide, in the presence of ammonia (NH3) over a tungsten oxide (WO3) catalyst. Taking EG-to-formamide as an example, we achieved a high formamide productivity of 537.7 μmol cm-2 h-1 with FE of 43.2 % at a constant current of 100 mA cm-2 in a flow electrolyzer with 12-h test, representing a more advantageous performance compared with previous reports for formamide electrosynthesis. Mechanistic understanding revealed that the cleavage of the C-C bond in the EG was facilitated by nucleophilic attack of in situ formed nitrogen radicals from NH3, with resultant C-N bond construction and eventually formamide production. Furthermore, this strategy can be extended to transformation of PET bottle and a series of biomass-derived polyols with carbon number from three (glycerol) to six (glucose), producing formamide with high efficiencies. This work demonstrates a sustainable upgrading strategy of plastic and biomass that may have implications to more value-added chemicals production beyond carbohydrates.

Utilizing PET bottles for sustainable cellular reinforcement: A study on enhancing fly ash backfill bearing strength with innovative geocell alternative

The slow degradation rate is one of the major global concerns. Only, 60 % produced is being recycled. Among these waste materials, Polyethylene Terephthalate (PET) bottles contribute around 10 % to the total plastic waste produced. The recycling process of PET bottles considering existing capacity in environmentally responsible ways is limited. It is estimated that 60 % of PET bottles produced are being disposed of in landfills. To overcome this, past studies have suggested novel approaches for using it as substitute for conventional geocell as soil reinforcement and stability. However, past studies mostly focused on application of PET bottles as flaked, shreds and sliced form. The present study attempts on application of PET bottles under fly ash (FA) backfills without mechanical alterations. Full-scale experiments were conducted on FA backfill system, for both unreinforced and reinforced conditions. A comparative study was performed between high-density polyethylene (HDPE) geocell and PET bottle mattress to assess the bearing strength of the FA backfill. Experiments were performed in a 1 m3 tank with a loading plate width of 200 mm. Vertical loading was applied onto the backfill footing (for all the trial series), till the footing settlement of 40 mm is achieved. An aspect ratio of 2 was considered for HDPE geocell and PET bottles. Rock quarry dust (RQD) was considered as cell infill and overlay material on FA backfill. The test results showed that settlement accumulation rate was low under reinforced scenario compared to the unreinforced condition, with higher resilient (elastic) settlement. RQD over the PET-reinforced zone was also seen to have enhanced the load distribution aspect, thereby reducing deformation in PET reinforcement. This usage of waste material will contribute towards sustainable development. This work demonstrates the feasibility and effectiveness of PET reinforcement to be used as replacement for HDPE geocell, which eventually can agument the design methodology of structural backfills.

A waste-to-wealth conversion of plastic bottles into effective carbon-based adsorbents for removal of tetracycline antibiotic from water

Currently, plastic waste and antibiotic wastewater are two of the most critical environmental problems, calling for urgent measures to take. A waste-to-wealth strategy for the conversion of polyethylene terephthalate (PET) plastic bottles into value-added materials such as carbon composite is highly recommended to clean wastewater contaminated by antibiotics. Inspired by this idea, we develop a novel PET-AC-ZFO composite by incorporating PET plastic-derived KOH-activated carbon (AC) with ZnFe2O4 (ZFO) particles for adsorptive removal of tetracycline (TTC). PET-derived carbon (PET-C), KOH-activated PET-derived carbon (PET-AC), and PET-AC-ZFO were characterized using physicochemical analyses. Central composite design (CCD) was used to obtain a quadratic model by TTC concentration (K), adsorbent dosage (L), and pH (M). PET-AC-ZFO possessed micropores (d ≈ 2 nm) and exceptionally high surface area of 1110 m2 g−1. Nearly 90% TTC could be removed by PET-AC-ZFO composite. Bangham kinetic and Langmuir isotherm were two most fitted models. Theoretical maximum TTC adsorption capacity was 45.1 mg g−1. This study suggested the role of hydrogen bonds, pore-filling interactions, and π-π interactions as the main interactions of the adsorption process. Thus, a strategy for conversion of PET bottles into PET-AC-ZFO can contribute to both plastic recycling and antibiotic wastewater mitigation.

Sulfonated cobalt phthalocyanine/NH2-MIL-125 heterojunction modified electrospun nanofiber membrane for emulsion separation and PMS-photocatalysis synergistic degradation

Membrane technology for wastewater remediation has generated significant interest, however, the single functionality, dull wettability and easy fouling property of the membrane hinder its practical application. Herein, a self-cleaning and multi-use superwetting nanofiber membrane was prepared by electrospinning and subsequent spraying technique. The sulfonated cobalt phthalocyanine/NH2-MIL-125 (CoPcS/NMIL) heterojunction was uniformly enrobed over polyethylene terephthalate (PET) electrospun membrane derived from waste PET bottles. The unique CoPcS/NMIL heterojunction exhibited a dual driving effect in photocatalytic activity and membrane wettability. Therefore, the fabricated CoPcS/NMIL@PET composite membrane demonstrated its capability to address complex water pollution issues effectively. The composite membrane exhibited notable flux permeation ability (538–3180 L m−2 h−1) and achieved excellent separation efficiency of over 99 % for diverse oil-in-water emulsions under the gravity filtration condition. Notably, the membrane can efficiently deal with stubborn high-viscosity crude oil fouling profiting from the photocatalytic self-cleaning function. A high flux recovery ratio of 93.6 % and a low irreversible fouling resistance ratio of 6.4 % can be obtained after 30 min of visible light irradiation. Impressively, CoPcS/NMIL@PET membrane exhibited enhanced permeation flux, separation efficiency and self-cleaning capacity compared to NMIL@PET membrane. Meanwhile, the CoPcS/NMIL@PET-activated peroxomonosulfate (PMS) system exhibited extremely high degradation performance for RhB under visible light with the degradation efficiency of 98 % within 10 min, suggesting its potential in the rapid purification of water-soluble organic pollutants. In addition, the CoPcS/NMIL@PET membrane has good chemical stability and mechanical properties for potential long-term use. Moreover, the demulsification mechanism in oil-water separation and PMS-photocatalysis synergetic mechanism over the fabricated CoPcS/NMIL@PET membrane were also investigated in detail. The research offers a promising approach for the design and fabrication of novel nanofiber membranes that incorporate photosensitizers and MOFs functional surfaces to address the challenges associated with such wastewater treatment.

Development of predictive model for compressive strength of eco-brick masonry walls using numerical method

The usage of waste plastics in the form of eco-bricks for the construction of buildings is gradually gaining traction. However, the performance of eco-brick masonry walls is not sufficiently known, and the process of setting up experimental rigs for the conduct of compressive strength test of masonry are usually cumbersome and expensive. This study investigated the compressive strength performance of eco-brick masonry walls and developed a predictive model for evaluating the strength of eco-brick masonry walls. Waste polyethylene terephthalate (PET) bottles were physically recycled and utilised to manufacture four samples of eco-bricks, strength grades 40.5, 21.02, 13.52 and 3.05 N/mm2 using stone dust, sharp sand and laterite at predetermined moisture contents. The eco-bricks were laid with seven grades of mortar to build 54 eco-brick masonry prisms. A quasi-static compressive loading test was carried out on the masonries, and predictive models were developed using multiple non-linear regression. The study found that eco-brick masonry prisms supported large loads and failed due to the propagation of tensile cracks and debonding of the units. The study also found that the compressive strength of eco-brick masonry is a power function of the compressive strength of eco-bricks and the mortar used for the bonding. It was determined that the mean ratio of the expected to experimental prism strength was 1.002. The mathematical model developed in this study for predicting the strength of eco-brick masonries can significantly evaluate the compressive strength of eco-brick masonry.

A New Sustainable PPT Coating Based on Recycled PET to Improve the Durability of Hydraulic Concrete.

A new, sustainable polypropylene terephthalate (PPT) coating was synthesized from recycled polyethylene terephthalate (PET) and applied onto a hydraulic concrete substrate to improve its durability. For the first step, PET bottle wastes were ground and depolymerized by glycolysis using propylene glycol (PG) in a vessel-type reactor (20-180 °C) to synthesize bis(2-hydroxypropyl)-terephthalate (BHPT), which was applied as a coating to one to three layers of hydraulic concrete substrate using the brushing technique and polymerized (150 °C for 15 h) to obtain PPT. PET, BHPT, and PPT were characterized by FT-IR, PET, and PPT using TGA, and the PPT coatings by SEM (thickness), ASTM-D3359-17 (adhesion), and water contact angle (wettability). The durability of hydraulic concrete coated with PPT was studied using resist chloride ion penetration (ASTM-C1202-17), carbonation depth at 28 days (RILEM-CPC-18), and the absorption water ratio (ASTM-C1585-20). The results demonstrated that the BHPT and PPT were synthetized (FT-IR), and PPT had a similar thermal behavior to PET (TGA); the PPT coatings had good adhesion to the substrate, with thicknesses of micrometric units. PPT coatings presented hydrophilic hydrophilic behavior like PET coatings, and the durability of hydraulic concrete coated with PPT (2-3 layers) improved (migration of chloride ions decreased, carbonation depth was negligible, and the absorption water ratio decreased).

Multi-criteria decision making tool for sustainable concrete production using waste polyethylene terephthalate bottle cap aggregates

The widespread use of concrete has raised concerns about the consumption of its raw materials. To address this issue, researchers are actively exploring alternative waste materials to reduce the environmental impact of the construction industry. With this objective current study aims to investigate potential use of waste polyethylene terephthalate (PET) bottle cap aggregates on the characteristics of concrete, both in its fresh and hardened states. Three variations of modified waste PET aggregates (PETA): full (F), half (H), and quarter (Q), with the aim of evaluating their suitability as replacements for conventional coarse aggregates (CCA) was examined. The research assesses the effects of different PETA proportions (3%, 5%, and 8%) on concrete workability, compressive strength, splitting tensile strength, and flexural strength. The findings reveal that PETA-F and PETA-H adversely affect workability, primarily due to their larger surface area and difficulty in achieving homogeneous blending with other ingredients. In contrast, PETA-Q exhibits superior workability. The use of PETA-Q results in reduced compressive strength due to its smaller size and limited load-bearing capacity. Notably, PETA-H demonstrates improved compressive strength after 28 days. Interestingly, PETA-Q shows enhancements in splitting tensile and flexural strength, making it the top-performing alternative for fresh and hardened concrete properties. Overall, this research indicates that PETA-Q is most suitable for sustainable concrete production. Furthermore, the application of a multi-criteria decision-making tool validates our findings and determines that a 5% replacement of CCA with PETA is optimal, as higher replacements result in strength reduction. The utilization of PETA not only minimizes CCA consumption but also contributes to the development of eco-friendly, sustainable concrete. This study underscores the potential of environmentally conscious concrete and encourages the adoption of sustainable solutions for plastic waste management.

Spent Lithium-Ion Batteries Derived Co3O4 for Electrocatalytic Polyethylene Terephthalate Plastic Recycling.

Spent lithium-ion batteries (LIBs) are an essential secondary resource containing valuable metal elements. Transforming spent LIBs into efficient catalysts through a simple process presents a promising strategy to address both metal resource scarcity and clean energy challenges. Herein, a deep eutectic solvent-assisted synthesis of Co3O4 material from spent LIBs is proposed. The obtained Co3O4 material possesses efficient and stable electrocatalytic activity for converting raw polyethylene terephthalate (PET) bottles into high-purity formic acid and terephthalic acid products under ambient conditions. As expected, the Co3O4 catalyst exhibits a high FE of 92 % with a concentration of produced potassium formate of 23.6 mM under alkaline conditions. This study presents a waste-treating-waste strategy for the simultaneous recovery of spent LIBs and PET waste in a greener manner.

Persistence of A-234 nerve agent on indoor surfaces

Understanding the fundamental physical characteristics of extremely toxic compounds and their behavior across different environments plays a crucial role in assessing their danger. Additionally, this knowledge informs the development of protocols for gathering forensic evidence related to harmful chemicals misuse. In 2018, former Russian spy Sergei Skripal and his daughter were poisoned in Salisbury, England, with a substance later identified as the unconventional nerve agent A-234. Contamination with the compound was found on items inside Skripal's home. The aim of this paper was to determine the persistence of A-234 on selected indoor surfaces. Ceramics, aluminum can, laminated chipboard, polyvinyl chloride (PVC) floor tile, polyethylene terephthalate (PET) bottle, acrylic paint and computer keyboard were used as matrices. The decrease in surface contamination and further fate of the compound was monitored for 12 weeks. Persistence determination involved optimizing the wipe sampling method. Simultaneously, evaporation from the surface and permeation of the contaminant into the matrix were closely monitored. The experimental findings indicate that the nerve agent exhibits remarkable persistence, particularly on impermeable surfaces. Notably, the process of A-234 evaporation plays a minor role in determining its fate, with detectable concentrations observed solely above solid, non-porous surfaces such as ceramics and aluminum can. The surface persistence half-life varied significantly, ranging from 12 min to 478 days, depending on the material. The article has implications for emergency response protocols, decontamination strategies, public health and crime scene investigations.

Abolishing Single-Use Plastic Water Bottles in Dubai Hotels as a Voluntary Act—Scenarios and Environmental Impacts

Dubai, a popular vacation spot, has launched an initiative to reduce reliance on single-use plastic water bottles. Tourists in Dubai widely utilize PET (Polyethylene Terephthalate) water bottles, and significant quantities of greenhouse gases (GHG) are released during the production and disposal of PET bottles. In response to Dubai’s initiative, some hotels eliminated PET bottles and substituted them with environmentally favorable alternatives. These hotels are considered adopters of the initiative, while other hotels that might follow are imitators. Thus, innovation diffusion theory (IDT) is used in this work to forecast the transition of hotels to non-PET bottles. The diffusion of this new behavior is simulated using a system dynamic (SD) model, where factors pushing imitators to abolish PET bottles are found using the Delphi method and hotel surveying. Moreover, the importance of each identified factor is found using an analytical hierarchical process (AHP). Since hotels are divided into several categories based on their service quality, the analysis shows that hotels are affected by other hotels in their category or better categories. Using this conceptual understanding, Bass and generalized Bass modeling are used in the SD model to study how imitating hotels will follow the adopters. Best-, average-, and worst-case scenarios are studied to help decision-makers understand what to expect in the future. For the best- and average-case scenarios, the SD simulation shows that all hotels will potentially have abolished PET bottles in 25 years. However, only 16% of hotels will have cancelled PET bottles in 25 years if the worst-case scenario occurs; thus, decision-makers need to intervene to expedite the process.

Cowpea storage: Can small farmers use polyethylene terephthalate bottles and wood ash as an alternative to avoid damage caused by Callosobruchus maculatus?

The aim of this study was to investigate the effectiveness of the combination of Polyethylene terephthalate (PET) bottles and ash in controlling Csllosobruchus maculatus and maintaining the quality of grains of cowpea cultivars. The following storage structures were used: PET bottle in airtight conditions and glass jars in non-airtight condition (control). The wood ash used in this research came from the burning process of eucalyptus (Eucalyptus grandis) wood. The experiment was carried out in a 2 × 2 × 4 factorial scheme, with two cowpea cultivars (BRS Tumucumaque and BRS Guariba), two forms of storage (PET bottle – airtight and glass jars – non-airtight) and four doses of eucalyptus wood ash (0.0; 1.0; 2.0 and 4.0 kg t−1), in a completely randomized design with three replications. Each plot contained 500 g of cowpea. The effectiveness of treatments was measured by the instantaneous population growth rate (ri) of C. maculatus. In ri, 35 adult, non-sexed insects were used. Adult progenies were counted after 60 days of storage. For qualitative grain evaluation the following characteristics were analyzed: water content, germination, apparent specific mass and electrical conductivity. The results obtained in this study confirm for the first time that the combined use of PET and ash do not affect grain quality and it is efficient in the management of C. maculatus in cowpea cultivars. In the present study, a significant reduction in the emergence of C. maculatus was observed in the BRS Tumucumaque, making it possible that this cultivar has some potential for resistance to bruchid.

Synthesis of Cr(OH)3/ZrO2@Co-based metal-organic framework from waste poly(ethylene terephthalate) for hydrogen production via formic acid dehydrogenation at low temperature

Recycling waste polyethylene terephthalate (PET) bottles into value-added ligand materials for synthesizing metal-organic frameworks (MOFs) derived catalysts is an eco-friendly and economically viable process. The waste PET bottles were readily broken down into 1,4-benzenedicarboxylic acid (BDC) ligands in a highly alkaline environment. Herein, we fabricated a Co@Cr(OH)3/ZrO2 catalyst via the carbonization of PET-derived UiO-66 metal-organic frameworks for the catalytic dehydrogenation of formic acid at low temperatures. The as-prepared Co@Cr(OH)3/ZrO2 catalyst provides a turnover frequency of 7685 h−1 for hydrogen generation (120 mL in 1.5 min) at ambient temperature. This is due to the uniform dispersion of the fine metal nanoparticle (NPs) (Co NPs, ∼3.75 nm) and the synergistic effect of the Co NPs and Cr(OH)3/ZrO2 supports. In addition, the characterization results indicate that porous Zr-MOFs may effectively enclose tiny particles, which is favorable for enhanced dehydrogenation performance. In addition, the Co@Cr(OH)3/ZrO2 catalysts demonstrated excellent stability against aggregation and were recyclable over seven cycles without any significant catalytic loss. Thus, this study provides a sustainable methodology for the development of MOF-derived, effective, and stable catalysts for formic acid dehydrogenation towards hydrogen production.

Vendor Managed Inventory (VMI) Implementation in Recycled PET Preform for The Beverage Industry

The beverage industry is a company that is focused on producing mineral water in Polyethylene Terephthalate (PET) bottles. PET bottles serve as the primary packaging choice in the beverage industry, making the use of preforms as a material for bottles unavoidable. On the other hand, the public is more aware of using sustainable materials. Adapting market awareness, the company shifted from virgin material to recycled material. Due to the significant initial investment, the company has decided on a single supplier strategy for recycled PET preform suppliers. This policy forces the company to manage the supplier to meet the company’s delivery accomplishment target. Currently, in the management of beverage found in the industry, the supplier only reaches 50% of delivery accomplishments, whereas the company target is 90%. The beverage industry strived for a revolution, so the company’s target was achieved. The vendor managed inventory method is implemented in this study to create a new revolution for PET preform suppliers, a new replenishment system. After the implementation of Vendor Managed Inventory (VMI), there has been an improvement, reaching 95% in delivery accomplishment. The adoption of vendor managed inventory ensures the attainment of the company’s objectives.

Daily Use Water Bottles as a Hub for Microbial Population: A Comparative Study of PET vs. Stainless Steel Water Bottles and Outcome of Washing Strategy Intervention

ABSTRACT Water bottles for everyday usage are a typical addition to people’s life and offer a practical way to stay hydrated. Even though safe and clean water is preferred for consumption, the water bottle or container used to drink water was never considered to be cleaned. Here, we examined the adhering microbial populations in water bottles composed of stainless steel (SS) and polyethylene terephthalate (PET). A total of 30 water bottles—15 PET and 15 SS—were gathered from different users. To identify and quantify the adhering microbial populations, microbial swabs from the inside surface of the bottles were collected and later cultivated on certain growth media. Overall the microbial load of PET is significantly higher than the SS water bottles of 68.8 + 19.1 cfu/ml and 35.4 + 8 cfu/ml respectively at initial sampling (P = 0.0027). We also evaluated the efficiency of various cleaning procedures in eliminating adherent bacteria populations. The cleaning strategy significantly reduced the microbial load (P<0.0001). The mean load observed was 11.2 + 2.3 cfu/ml post-wash. This comparison study offers important new information about the adherent microbial populations found in SS and PET water bottles used every day, in the end. This finding emphasizes the necessity of routine cleaning and upkeep of these bottles to reduce the possibility of microbial contamination and the accompanying health risks.