Poly Ethylene Oxide Research Articles

Desulfurising Fuels Using Alcohol-Based Deep Eutectic Solvents Using Extractive Catalytic Oxidative Desulfurisation Method

Removal of sulfur compounds from transportation fuels is a requirement in the worldwide effort to reduce emissions from transportation fuels. Refineries use the hydrodesulfurisation (HDS) process to reduce sulfur compounds in fuels. However, the HDS process requires high hydrogen pressure and temperature, making it costly. An alternative to the HDS process is oxidative desulfurisation via solvent extraction, which requires low-temperature operating conditions. In this regard, deep eutectic solvents (DESs) are attractive for researchers to desulfurise transportation fuels via solvent extraction due to their low-cost. In our study, DESs were synthesised using phenylacetic acid (PAA) and salicylic acid (SAA) as hydrogen bond acceptors (HBAs) and tetraethylene glycol (TTEG) as hydrogen bond donor (HBD) in the mole ratio of 1:2. DESs were characterised by using Fourier transform infrared (FTIR) spectroscopy. Physicochemical properties of DESs, such as density, viscosity and refractive index, were also measured. The synthesised DESs were used to extract organosulfur compounds from model fuel and actual diesel. An oxidation study was carried out for model fuel and diesel, followed by solvent extraction using these synthesised DESs. The extraction efficiency for PAA/TTEG(1:2) and SAA/TTEG(1:2) was achieved as 50.16% and 38.89% for model fuel at a temperature of 30°C using a solvent to feed ratio of 1.0 while for diesel, it was 38% and 37%. However, it increased to 77%, 68% and 54%, 73%, respectively, for PAA/TTEG(1:2) and SAA/TTEG(1:2) when the feedstocks were oxidised. These results showed better extraction performance of DES PAA/TTEG(1:2) than that of SAA/TTEG(1:2) at low temperature 30°C using combined extractive catalytic oxidative desulfurisation. Hence, the DES synthesised using SAA and TTEG in the molar ratio of 1:2 works better as an extraction solvent for removing organic sulfur compounds from fuels at low temperatures.

Attapulgite Enhanced Polyethylene Oxide-Polyvinylidene Difluoride-Based Composite Solid-State Electrolyte for All Solid State Li-Ion Batteries

We report an attapulgite-modified poly(ethylene oxide) (PEO) based solid-state composite electrolyte film by solution casting method. The influence of attapulgite and polyvinylidene difluoride (PVDF) on the electrical properties of PEO-based solid-state electrolytes was investigated and it is found that an optimal 3% attapulgite and 10% PVDF in the electrolyte film (0.9PEO-0.1PVDF-LiClO4-3% attapulgite) exhibited a high ionic conductivity of 2.55×10−4 S cm−1 at room temperature and electronic conductivity of 2.25×10−11 S cm−1. Furthermore, The LiFePO4/0.85PEO-0.15PVDF-LiClO4-3% attapulgite/Li all-solid battery exhibited a promising initial discharge capacity of 120 mAh g−1, and even after 10 cycles at 0.1 C, the specific capacity values of the all-solid battery remained above 60 mAh g−1.

Self‐Supporting Solid Electrolyte Based on Supramolecular Interaction for Stable Li Metal Batteries

AbstractLi metal batteries based on solid polymer electrolytes offer the benefits of high energy density and safety, as well as extended cycling life, making them an excellent candidate for the next‐generation battery system. However, current solid polymer electrolytes still suffer from low ion conductivity and Li+ transfer number, which seriously restricts its practical application. Herein, a self‐supporting composite solid polymer electrolyte was prepared, where phenolic resin rich in hydroxyl groups (BR) and polyethylene oxide (PEO) are mixed evenly and poured onto a cellulose membrane in one step. In such an electrolyte, PEO and BR combine to form intermolecular hydrogen bonds, lowering the crystallinity of PEO and increasing the Li+ transfer number. Lastly, the obtained solid electrolytes exhibited a high ion conductivity (1.1×10−4 S cm−1) and Li+ transfer number (0.53), as well as improved electrochemical window. Consequently, Li || Li symmetrical cells can run stably for more than 700 h at 0.1 mA cm−2/0.25 mAh cm−2. And full cells with LiFePO4 cathode can also demonstrate high discharge capacity of 152.12 mAh g−1 and rate performance. We believe that such a design based on supramolecular interaction offer a new avenue to advanced solid polymer electrolytes.

Rapid-Response Water-Shrink Films with High Output Work Density Based on Polyethylene Oxide and α-Cyclodextrin for Autonomous Wound Closure.

Conventional wound closure methods, including sutures and tissue adhesives, present significant challenges for self-care treatment, particularly in the context of bleeding wounds. Existing stimuli-responsive contractile materials designed for autonomous wound closure frequently lack sufficient output work density to generate the force needed to bring the wound edges into proximity or necessitate stimuli that are not compatible with the human body. Here, semi-transparent, flexible, and water-responsive shrinkable films, composed of poly(ethylene oxide) and α-cyclodextrin, are reported. These films exhibit remarkable stability under ambient conditions and demonstrate significant contraction (≈50%) within 6 s upon exposure to water, generating substantial contractile stress (up to 6MPa) and output work density (≈1028kJ m-3), which is 100 times larger than that of conventional hydrogel and 25 times larger than that of skeletal muscles. Remarkably, upon hydration, these films are capable of lifting objects 10000 times their own weight. Leveraging this technology, water-shrink tapes, which, upon contact with water, effectively constrict human skin and autonomously close bleeding wounds in animal models within 10 seconds, are developed further. This work offers a novel approach to skin wound management, showing significant potential for emergency and self-care scenarios.

First-Principles Study on Polymer Electrolyte Interface Engineering for Lithium Metal Anodes.

Modifying the interface between the lithium metal anode (LMA) and the electrolyte is crucial for achieving high-performance lithium metal batteries (LMBs). Recent research indicates that altering Li-metal interfaces with polymer coatings is an effective approach to extend LMBs' cycling lifespan. However, the physical properties of these polymer-Li interfaces have not yet been fully investigated. Therefore, the structural stability, electronic conductivity, and ionic conductivity of polymer-Li interfaces were examined based on first-principles calculations in this study. Several representative polymer compounds utilized in LMBs were assessed, including polyacrylonitrile (PAN), polyvinylidene fluoride (PVDF), polytetrafluoroethylene (PTFE), and polyethylene oxide (PEO). Our research revealed that lithium fluoride is formed upon fluoropolymer degradation, explaining previously observed experimental results. Polymers containing nitrile groups exhibit strong adhesion to lithium metal, facilitating the formation of the stable interface layer. Regarding electronic conductivity, the fluoropolymers preserve a good insulating property, which diminished marginally in the presence of lithium, but that of PAN and PEO significantly reduces. Additionally, lithium diffusion on PTFE and PEO demonstrates low diffusion barriers and high coefficients, enabling easy transportation. Overall, our investigation reveals that the interfaces formed between various polymers and LMA have distinct characteristics, providing new fundamental insights for designing composites with tailored interface properties.

Contact Angle Modulation: In Situ Polymer Deposition during Sessile Drop Evaporation.

The drying kinetics of a sessile drop on a solid surface are a widely studied phenomenon because of their relevance to various fields such as coating, printing, medical diagnostics, sensing, and microfluidic technology. Typically, the drop undergoes drying either at a constant contact radius (R) with a decrease in the three-phase contact angle or at a constant contact angle (θ) with a reduction in the radius with time. These two drying modes are referred to as CCR and CCA, respectively. It is not uncommon where both R and θ may decrease during drying, especially in the penultimate stage of drying. In this work, we report a scenario wherein the θ increases while R decreases during the drying process of an aqueous polymer solution on a high surface energy substrate. This behavior is observed across different polymer systems (such as poly(ethylene oxide) and polyvinyl pyrrolidine), varying molecular weights, and polymer concentrations. As the drop dries, the polymer gets deposited at the three-phase contact line, thus reducing the surface energy of the substrate and leading to an increase in the contact angle. The drop responds by attempting to reach a new equilibrium contact angle through slipping. The temporal increase in contact angle follows a power law scaling behavior. This study demonstrates an in situ modulation of contact angle facilitated by evaporation and polymer deposition, showcasing unconventional drying dynamics.

High-Strength, Thin, and Lightweight Solid Polymer Electrolyte for Superior All-Solid-State Sodium Metal Batteries.

The utilization of solid polymer electrolytes (SPEs) in all-solid-state sodium metal batteries has been extensively explored due to their excellent flexibility, processability adaptability to match roll-to-roll manufacturing processes, and good interfacial contact with a high-capacity Na anode; however, SPEs are still impeded by their inadequate mechanical strength, excessive thickness, and poor stability with Na anodes. Herein, a robust, thin, and cost-effective polyethylene (PE) film is employed as a skeleton for infiltrating poly(ethylene oxide)-sodium bis(trifluoromethanesulfonyl)imide (PEO/NaTFSI) to fabricate PE-PEO/NaTFSI SPE. The resulting SPE features a remarkable thickness of 25 μm, lightweight property (2.1 mg cm-2), superior mechanical strength (tensile strength = 100.3 MPa), and good flexibility. The SPE also shows an ionic conductivity of 9.4 × 10-5 S cm-1 at 60 °C and enhanced interfacial stability with a sodium metal anode. Benefiting from these advantages, the assembled Na-Na symmetric cells with PE-PEO/NaTFSI show a high critical current density (1 mA cm-2) and excellent long-term cycling stability (3000 h at 0.3 mA cm-2). The all-solid-state Na||PE-PEO/NaTFSI||Na3V2(PO4)3 coin cells exhibit a superior cycling performance, retaining 93% of the initial capacity for 190 cycles when matched with a 6 mg cm-2 cathode loading. Meanwhile, the pouch cell can work stably after abuse testing, proving its flexibility and safety. This work offers a promising strategy to simultaneously achieve thin, high-strength, and safe solid-state electrolytes for all-solid-state sodium metal batteries.

Selective biodegradation of octylphenol polyethoxylates with different ethoxylate length chains by aerobic bacterial culture

Octylphenol polyethoxylates (OPEOn) are composed of a hydrophobic octylphenol (OP) group and a hydrophilic polyethylene oxide (EO) chain and are widely used in commercial products. Shorter EO chains and OPEOn biometabolites have been identified as endocrine-disrupting contaminants and can threaten biotic factors in the ecosystem. In this study, OPEOn at three EO lengths (TX-45, TX-114, and TX-165) were selected in monomer (MN) or micelle (MC) state for batch experiments under aerobic conditions, with results showing biodegradation rates of 90 % within 35–70 h. The pseudo-first-order constant (k) of OPEOn biodegradation was observed in the order TX-45 (0.1414 h−1) > TX-114 (0.0556 h−1) > TX-165 (0.0485 h−1), with biomineralisation reaching at least 80 % for all OPEOn. The selective biodegradation of EO chains was also measured, with initial accumulation of OPEO3 observed along with the depletion of longer EO chains for TX-45 and TX-114 in both the MN and MC states. A similar trend was observed for the MN state of TX-165, with OPEO3-OPEO9 observed to accumulate and reduced after 70 h. MC biodegradation was accomplished via the initial accumulation of OPEO3-OPEO9. The amounts of OPEO3 increased and others reduced; however, OPEO3 remained high at the end of biodegradation for TX-165. Bacterial community analysis indicated that the genera Sphingobium spp., Pseudomonas spp., Flavobacterium spp., Comamonas spp., and Sphingopyxis spp. dominate OPEOn biodegradation, and they have their roles during biodegradation, and the community-level physiological profile (CLPP) was also changed by biodegradation in both the MN and MC states.

Novel PEO-based Solid Polymer Electrolyte with High Elasticity and High Ionic Conductivity for Room Temperature Lithium Metal Batteries

The development and application of polyethylene oxide (PEO) based solid polymer electrolyte (SPE) is severely constrained by its low ionic conductivity and poor tensile resistance. To improve the electrochemical performance of SPE without losing its mechanical properties, a benzene sulfonate-based additive is adopted into crosslinking system composed of -CH2-CH2-O- segments to obtain a membrane with a high ionic conductivity of 1.47 × 10−4 S cm−1 and an ionic transference number of 0.70 at room temperature. The activation energy value of 0.128 eV gives evidence for a favorable migration mechanism of PTH-SPE. Anti-dendrite growth and contact optimization can be realized by molecular structure design with a tensile elongation of 490%. The reversible overpotential of Li||Li symmetric cell within 1000 h demonstrates that the compact PTH-SPE can inhibit the growth of lithium dendrite. This work provides a new strategy for designing high-performance solid electrolytes for room temperature via a green solvent-free method.

A new two-dimensional, spiropyran-based polymer fluorescent nanoprobe with quantitative-fluorescent and photochromic properties for multi-substance detection

One challenge of the structural design of a fluorescent probe is how to improve the detection performance on trace target analytes in complex samples. Herein a new polymer fluorescent nanoprobe (2DSP-C28) has been synthesized, by adopting a two-dimensional (2D), spiropyran (SP)-based nanosheet structure with hydrophobic long-chain alkanes (C28). Unlike a traditional SP-based small molecule probe, the 2DSP-C28 probe can exhibit quantitative-fluorescent and photochromic properties. Under the detection of metal-ions, the nanoprobe in dimethyl sulfoxide aqueous solution is selectively fluorescent-quenched-responsive for Fe-ions (∼100 μM), with a characteristic stoichiometric ratio of <10, a high sensitivity (limit of detection: ∼0.2 μM). When the nanoprobe is incorporated into electrospun polyethylene oxide, it can be used for gas detection, and display a color-change with acid-base gas and identify the HF gas. It is expected that this new polymer fluorescent nanoprobe can be promisingly applied for rapidly environmental monitoring on the ion or gas pollution.

Porous PVDF composites with ultralow percolation threshold for wide-range dynamic and static pressure sensing

Porous conductive polymer composites are very attractive for static pressure sensing due to high sensitivity and good elasticity contributed by the porous structure, while they are hard to detect dynamic pressure. Herein, we report a porous conductive poly (vinylidene fluoride) (PVDF) composite capable of detecting static and dynamic pressure over a pressure range of 0–1 MPa, which was fabricated by melt mixing PVDF, polyethylene oxide (PEO) and carbon nanofillers, followed by etching PEO with water. Such porous PVDF composites have a very low percolation threshold (0.035 wt%) of carbon nanostructures (i.e., branched carbon nanotubes) thanks to the selective distribution of conductive fillers in the pore wall after etching. At the same time, the pore size and porosity of the porous PVDF composites can be tuned by the molecular weight (Mw) and blending ratios of two polymers, leading to the kinetically-tailorable blend morphology for tunable mechanical and electrical properties. The as-fabricated porous PVDF composites with a good combination of mechanical properties and electrical conductivities, which can be used as pressure sensors toward wide-range (0–1 MPa) dynamic and static pressure sensing. Such pressure sensors demonstrate potential applications in detecting the degree of finger bending, distinguishing the walking and running, and monitoring a series of technical movements in playing soccer, i.e., static and dynamic exercises.

Aqueous size exclusion chromatography applied to polymer analysis: experimental conditions and molecular weight calibration curves

Aqueous mode size exclusion chromatography (SEC) was employed for the analysis and construction of molecular weight (MW) calibration curves of three water-soluble polymers, namely, polyethylene glycol, polyethylene oxide, and polyacrylic acid sodium salt. Several calibration curves were obtained, varying chromatographic conditions such as columns arrangement, ionic strength, temperature and pH, in addition trends in polymeric chromatographic behavior were examined. The variation in SEC distribution coefficients at different temperatures was found to be below 10 %, indicating that the studied polymers follow an ideal SEC mechanism under the tested conditions. Thus, differences in chromatographic behavior were ascribed to changes in polymer configuration induced by media and/or temperature. These variations in morphology were consistent with the observed SEC behavior.Regarding MW calibration, polynomial regression models ranging from first to fifth order were applied, and the most adequate ones were selected based on their fit and prediction capabilities. Third order polynomials were the preferred models for polyethylene glycol and polyacrylic acid sodium salt, independently of chromatographic conditions. Meanwhile for polyethylene oxide, either third or fifth-order polynomial models were optimal depending on the chromatographic conditions. All the selected regression models presented coefficients of multiple determination (R2) above 0.990, while achieving relative errors of prediction (REP%) in MW ranging from 0.3 to 4 % for cross-validation.

Regulating Zn2+Migration-Diffusion Behavior by Spontaneous Cascade Optimization Strategy for Long-Life and Low N/P Ratio Zinc Ion Batteries.

Parasitic side reactions and dendrite growth on zinc anodes are formidable issues causing limited lifetime of aqueous zinc ion batteries (ZIBs). Herein, a spontaneous cascade optimization strategy is first proposed to regulate Zn2+ migration-diffusion behavior. Specifically, PAPE@Zn layer with separation-reconstruction properties is constructed in-situ on Zn anode. In this layer, well-soluble poly(ethylene oxide) (PEO) can spontaneously separation to bulk electrolyte and weaken the preferential coordination between H2O and Zn2+ to achieve primary optimization. Meanwhile, poor-soluble polymerized-4-acryloylmorpholine (PACMO) is reconstructed on Zn anode as hydrophobic flower-like arrays with abundant zincophilic sites, further guiding the de-solvation and homogeneous diffusion of Zn2+ to achieve the secondary optimization. Cascade optimization effectively regulates Zn2+ migration-diffusion behavior, dendrite growth and side reactions of Zn anode are negligible, and the stability is significantly improved. Consequently, symmetrical cells exhibit stability over 4000 h (1 mA cm-2). PAPE@Zn//NH4+-V2O5 full cells with a high current density of 15 A g-1 maintains 72.2% capacity retention for 12000 cycles. Even better, the full cell demonstrates excellent performance of cumulative capacity of 2.33 Ah cm-2 at ultra-low negative/positive (N/P) ratio of 0.6 and a high mass-loading (~17 mg cm-2). The spontaneous cascade optimization strategy provides novel path to achieve high-performance and practical ZIBs.

Lithium Borate Polycarbonates for High-Capacity Solid-State Composite Cathodes.

Improving composite cathode function is key to the success of the solid-state battery. Maximizing attainable cathode capacity and retention requires integrating suitable polymeric binders that retain a sufficiently high ionic conductivity and long-term chemo-mechanical stability of the cathode active material-solid-electrolyte-carbon mixture. Herein, we report block copolymer networks composed of lithium borate polycarbonates and poly(ethylene oxide) that improved the capacity (200 mA h g-1 at 1.75 mA cm-2) and capacity retention (94% over 300 cycles) of all-solid-state composite cathodes with nickel-rich LiNi0.8Co0.1Mn0.1O2 cathode active material, Li6PS5Cl solid electrolyte, and carbon. Tetrahedral B(OR)2(OH)2- anions immobilized on the polycarbonate segments provide hydrogen-bonding chain crosslinking and selective Li-counterion conductivity, parameterized by Li-ion transference numbers close to unity (tLi+ ~ 0.94). With 90 wt% polycarbonate content and a flexible low glass transition temperature backbone, the single-ion conductors achieved high Li-ion conductivities of 0.2 mS cm-1 at 30°C. The work should inform future binder design for improving the processability of cathode composites towards commercialising solid-state batteries, and allow use in other cell configurations, such as lithium-sulphur cathode designs.

Effects of Polymers on Cocrystal Growth in a Drug-Drug Coamorphous System: Relations between Glass-to-Crystal Growth and Surface-Enhanced Crystal Growth.

Coamorphous and cocrystal drug delivery systems provide attractive crystal engineering strategies for improving the solubilities, dissolution rates, and oral bioavailabilities of poorly water-soluble drugs. Polymeric additives have often been used to inhibit the unwanted crystallization of amorphous drugs. However, the transformation of a coamorphous phase to a cocrystal phase in the presence of polymers has not been fully elucidated. Herein, we investigated the effects of low concentrations of the polymeric excipients poly(ethylene oxide) (PEO) and poly(vinylpyrrolidone) (PVP) on the growth of carbamazepine-celecoxib (CBZ-CEL) cocrystals from the corresponding coamorphous phase. PEO accelerated the growth rate of the cocrystals by increasing the molecular mobility of the coamorphous system, while PVP had the opposite effect. The coamorphous CBZ-CEL system exhibited two anomalously fast crystal growth modes: glass-to-crystal (GC) growth in the bulk and accelerated crystal growth at the free surface. These two fast growth modes both disappeared after doping with PEO (1-3% w/w) but were retained in the presence of PVP, indicating a potential correlation between the two fast crystal growth modes. We propose that the different effects of PEO and PVP on the crystal growth modes arose from weaker effects of the polymers on cocrystallization at the surface than in the bulk. This work provides a deep understanding of the mechanisms by which polymers influence the cocrystallization kinetics of a multicomponent amorphous phase and highlights the importance of polymer selection in stabilizing coamorphous systems or preparing cocrystals via solid-based methods.

Solid polymer electrolytes with fragment-separated microphase for advanced Li ion transport and highly stable lithium metal batteries

Solid polymer electrolytes (SPEs) with high ionic conductivity and good interfacial compatibility are one of the main factors constraining the performance of lithium metal batteries. However, the most common PEO (Polyethylene oxide)-based SPEs always lack of considerable relaxation of PEO segments, and therefore fail to apply into practical situations. Herein a novel method to prepare fragment-separated epoxy polymer electrolytes (FSEEs) characterized with fragment-separated microphase patterns via a rigid-and flexible monomers cross-link reaction is presented to enhance the overall SPE performance. The fragment-separated microphase can separate the PEO chains in framework and improve the relaxation of PEO chains, optimize the Li+ transport, where the ionic conductivity can be up to 0.56 mS cm−1 at 25 °C. The fragment-separated Li+ transport mechanism in FSEEs also provide better interfacial compatibility than that of PEO due to the even Li+ distribution at interface. The utilization of FSEE-S in Li/Li symmetric cells demonstrated a stable voltage plateau after cycling for 2000 h. Additionally, Li/LFP batteries exhibit favorable 0.5 C performance under 45 °C, lasting over 600 h and exceeding 150 cycles. This study offers a promising approach to SPE design, which may catalyze further exploration of the role of microphase in SPE performance.

Preparation and Characterization of Chitosan Nanofiber: Kinetic Studies and Enhancement of Insulin Delivery System.

Insulin-loaded nanofibers were prepared using chitosan as a natural polymer. The loaded insulin with polyethylene oxide was used for preparing monolayer batch S1. Nanofiber S1 was coated by seven layers of film on both sides to form batch S2 as a sandwich containing Layer A (CS, PEG and PEO) and Layer B (PEG and PEO) using electrospinning apparatus. SEM, TEM and FT-IR techniques were used to confirm the drug loading within the composite nanofibers. The in vitro activity that provided a sustained and controlled release of the drug from the nanofiber batch was studied at different pH values spectrophotometrically using a dialysis method. In batches S1 and S2, the release of insulin from nanofiber proceeds via burst release necessary to produce the desired therapeutic activity, followed by slow step. The rate and the percentage release of insulin in batch S2 are found to be higher at all pH values.

Influence of Screw Design and Process Parameters on the Product Quality of PEO:LiTFSI Solid Electrolytes Using Solvent-Free Melt Extrusion

All-solid-state battery (ASSB) technology is a new energy system that reduces the safety concerns and improves the battery performance of conventional lithium-ion batteries (LIB). The increasing demand for such new energy systems makes the transition from laboratory scale production of ASSB components to larger scale essential. Therefore, this study investigates the dry extrusion of poly(ethylene oxide):lithium bis (trifluoromethylsulfonyl)imide (PEO:LiTFSI) all-solid-state electrolytes at a ratio of 20:1 (EO:Li). We investigated the influence of different extruder setups on the product quality. For this purpose, different screw designs consisting of conveying, kneading and mixing elements are evaluated. To do so, a completely dry and solvent-free production of PEO:LiTFSI electrolytes using a co-rotating, intermeshing, twin-screw extruder under an inert condition was successfully carried out. The experiments showed that the screw design consisting of kneading elements gives the best results in terms of process stability and homogeneous mixing of the electrolyte components. Electrochemical impedance spectroscopy was used to determine the lithium-ion conductivity. All electrolytes produced had an ionic conductivity (σionic) of (1.1–1.8) × 10−4 S cm−1 at 80 °C.

The Incorporated Drug Affects the Properties of Hydrophilic Nanofibers.

Hydrophilic nanofibers offer promising potential for the delivery of drugs with diverse characteristics. Yet, the effects of different drugs incorporated into these nanofibers on their properties remain poorly understood. In this study, we systematically explored how model drugs, namely ibuprofen, carvedilol, paracetamol, and metformin (hydrochloride), affect hydrophilic nanofibers composed of polyethylene oxide and poloxamer 188 in a 1:1 weight ratio. Our findings reveal that the drug affects the conductivity and viscosity of the polymer solution for electrospinning, leading to distinct changes in the morphology of electrospun products. Specifically, drugs with low solubility in ethanol, the chosen solvent for polymer solution preparation, led to the formation of continuous nanofibers with uniform diameters. Additionally, the lower solubility of metformin in ethanol resulted in particle appearance on the nanofiber surface. Furthermore, the incorporation of more hydrophilic drugs increased the surface hydrophilicity of nanofiber mats. However, variations in the physicochemical properties of the drugs did not affect the drug loading and drug entrapment efficiency. Our research also shows that drug properties do not notably affect the immediate release of drugs from nanofibers, highlighting the dominant role of the hydrophilic polymers used. This study emphasizes the importance of considering specific drug properties, such as solubility, hydrophilicity, and compatibility with the solvent used for electrospinning, when designing hydrophilic nanofibers for drug delivery. Such considerations are crucial for optimizing the properties of the drug delivery system, which is essential for achieving therapeutic efficacy and safety.

Neuron‐Like Silicone Nanofilaments@Montmorillonite Nanofillers of PEO‐Based Solid‐State Electrolytes for Lithium Metal Batteries with Wide Operation Temperature

AbstractPoly(ethylene oxide) (PEO)‐based composite solid electrolytes (CSEs) are promising to accelerate commercialization of solid‐state lithium metal batteries (SSLMBs). Nonetheless, this is hindered by the CSEs’ limited ion conductivity at room temperature. Here, we propose design, synthesis, and application of the bioinspired neuron‐like nanofillers for PEO‐based CSEs. The neuron‐like superhydrophobic nanofillers are synthesized by controllably grafting silicone nanofilaments onto montmorillonite nanosheets. Compared to various reported fillers, the nanofillers can greatly improve ionic conductivity (4.9×10−4 S cm−1, 30 °C), Li+ transference number (0.63), oxidation stability (5.3 V) and mechanical properties of the PEO‐based CSEs because of the following facts. The distinctive neuron‐like structure and the resulting synaptic‐like connections establish numerous long‐distance continuous channels over various directions in the PEO‐based CSEs for fast and uniform Li+ transport. Consequently, the assembled SSLMBs with the CSEs and LiFePO4 or NCM811 cathodes display superior cycling stability over a wide temperature range of 50 °C to 0 °C. Surprisingly, the pouch batteries with the large‐scale prepared CSEs kept working after being repeatedly bent, folded, cut or even punched in air. We believe that design of neuron‐like nanofillers is a viable approach to produce CSEs with high room temperature ionic conductivity for SSLMBs.