Planar Probe Research Articles

Performance Investigation of Multi-Turn Pickup for Circular Fractal Flexible Planar Eddy Current Probe

ABSTRACT This paper aims to compare and analyze the performance differences between a single-coil and multi-coil pickup coil layout in a flexible circular fractal planar eddy current probe. Flexible planar eddy current probes offer flexibility and adaptability, making them widely used in the detection of complex structures. The circular fractal flexible planar eddy current probe is a new type of probe that has a lower miss rate in detecting cracks at specific angles compared to traditional circular and rectangular coil eddy current probes. However, the single-coil structure of the probe’s pickup coil has the drawback of being less sensitive to weak signals. This paper investigates the detection performance of the flexible circular fractal probe by varying the number of turns in the original pickup coil. Experimental comparisons were conducted by preparing and installing single-coil and multi-coil circular fractal planar eddy current probes. The performance differences between single-coil and multi-coil configurations were compared and analyzed under various excitation frequencies, liftoff distances, and internal crack depths. The results showed that, compared to the single-coil probe, the multi-coil probe exhibited significantly improved detection signal values and sensitivity.

Pulsed laser deposition of MoS2 thin films at different mean kinetic plasma energies

In recent years, molybdenum disulfide has become a material of great interest for research for electronic and optoelectronic applications due to its 2-dimensional graphene-like structure and its bandgap within the visible spectrum. In this work, thin films of MoS2 were grown using pulsed laser deposition on glass substrates at room temperature and at deposition pressure of 2 × 10−5 Torr. We ablated a MoS2 target obtained by compressing high-purity powders, with a Nd-YAG pulsed laser with a wavelength of 1064 nm, 6 ns pulse width, and 10 Hz repetition rate. Laser produced plasmas were diagnosed by means of the time-of-flight technique using a Langmuir planar probe, from which mean kinetic energy and density of ions were estimated. Experimental control is more reliable using plasma parameters rather than fluence. The crystalline properties of the deposits were characterized using Raman spectroscopy and X-Ray diffraction; their chemical analysis was carried out by X-ray photoelectron spectroscopy; their thickness and morphology were characterized using atomic force microscopy and scanning electron microscopy, respectively. Results are discussed as a function of mean kinetic energy variations. It was observed that as the mean kinetic energy of the plasma decreased, the crystallinity improved and the crystal size increased.

Floating potential probes for process control during reactive magnetron sputtering

Long term deposition of aluminum oxide by reactive magnetron sputtering results in a drift of the discharge voltage. A similar drift of the floating potential is observed. The latter observation is further investigated and it is shown that the change of the floating potential can be linked to a change of the electric properties of the vacuum chamber walls. Optimization of the floating potential probe is performed to use the difference between the discharge voltage and the floating potential as a parameter for process control. The best results were obtained with a planar probe sufficiently far positioned opposite to the magnetron, and close enough to the chamber wall facing the magnetron. This choice can be understood in terms of the ability of the probe to sense the discharge while being protected from deposition. The usage of the aforementioned difference to control the process is demonstrated with the measurement of process curves, more specifically IV-characteristics and hysteresis experiments. The shown reproducibility of these measurements opens a pathway for more precise quantification of reactive sputter deposition simulations and enhanced process control.

Development of a microwave sensor for the non-invasive detection of plant responses to water stress: A practical application on maize (Zea mays L.)

In this study, a novel microwave sensing system, consisting of a microstrip self-resonant spiral coil inductively coupled to an external concentric planar probe loop, is presented and applied to the non-destructive detection of morpho-physiological plant responses to water stress. The optimised set-up of the proposed sensor ensures a highly sensitive spiral coil, which is a fundamental requirement to derive accurate information on plants' behavioural alterations related to water stress conditions. The proposed microwave sensor was tested it on two potted maize cultivars (Zea mays L.), namely “Cinquantino Bianchi” (CB) and “Scagliolo Frassine” (SF). For each cultivar, half of the samples were maintained at 100% (T100) field capacity while the other half was at 25% (T25) from 46 to 74 Days After Sowing (DAS). The frequency (fr) shift and the amplitude peaks variation of the real component of the external planar probe input impedance (ℜ(Zinput)) were obtained daily by positioning the sensor on the stem. These measured data were related to morpho-physiological parameters destructively acquired at four different growth stages. The resulting linear correlation between the stem's freshwater content (FWCstem) with both fr (r > −0.64) and the amplitude peaks (ℜ (Zinput)) (r > -0.70) provided evidence of the sensor's ability to identify stem dielectric properties' variations between the two water treatments. Concurrently, the sensor response demonstrated the capability to identify changes in the morphology and histology of the stem. Based on preliminary findings, the proposed sensor shows potential for employment in the real-time monitoring of plant water status, contributing to more economically and environmentally sustainable crop management practices. While the current correlations between plant water content and sensor measurements require further refinement to meet the rigorous industrial standards, nevertheless a large-scale adoption can be envisioned by leveraging IoT methodologies.

Properties of the ionization region in a magnetron plasma at gas-aggregation-source-relevant pressure regime explored using a global model

A global (volume averaged) model is developed for the ionization region (IR) of a gas aggregation source (GAS) plasma. The case of using argon gas and a copper target is considered. The model describes the densities of thermal and hot electrons, argon and copper ions, copper atoms and argon atoms in different excited states, the temperature of thermal electrons, the kinetic energies of the ions with which they bombard the target, the sheath width near the target cathode and the energy fluxes by different plasma species to a planar probe in the IR. Also, the fraction of input power is estimated which is dissipated to energize the thermal electrons in the IR. The gas discharge properties are analyzed for different pressures and discharge currents under conditions corresponding to the experimental conditions (Gauter et al 2018 J. Appl. Phys. 124 073301). The calculated pressure- and current-dependences for the GAS properties are used to explain the measured dependences for the deposition rate and the energy flux. It is found that the deposition rate increases with increasing discharge current because of the growth of currents of copper atoms and ions. With increasing pressure, the rate decreases due to drop of the densities of copper atoms and ions because of decreasing the kinetic energies of the ions with which they bombard the target. The model indicates that in the gas-aggregation-source relevant pressure regime, the energy flux by ions dominates over the energy fluxes of other plasma species.

Lift-Off Effect of Koch and Circular Differential Pickup Eddy Current Probes

A flexible or planar eddy current probe with a differential structure can suppress the lift-off noise during the inspection of defects. However, the extent of the lift-off effect on differential probes, including different coil structures, varies. In this study, two planar eddy current probes with differential pickup structures and the same size, Koch and circular probes, were used to compare lift-off effects. The eddy current distributions of the probes perturbed by 0° and 90° cracks were obtained by finite element analysis. The analysis results show that the 90° crack can impede the eddy current induced by the Koch probe even further at relatively low lift-off distance. The peak-to-peak values of the signal output from the two probes were compared at different lift-off distances using finite element analysis and experimental methods. In addition, the effects of different frequencies on the lift-off were studied experimentally. The results show that the signal peak-to-peak value of the Koch probe for the inspection of cracks in 90° orientation is larger than that of the circular probe when the lift-off distance is smaller than 1.2 mm. In addition, the influence of the lift-off distance on the peak-to-peak signal value of the two probes was studied via normalization. This indicates that the influence becomes more evident with an increase in excitation frequency. This research discloses the lift-off effect of differential planar eddy current probes with different coil shapes and proves the detection merit of the Koch probe for 90° cracks at low lift-off distances.

Fabrication and Characterization of PDMS Waveguides for Flexible Optrodes.

With the growth of optogenetic research, the demand for optical probes tailored to specific applications is ever rising. Specifically, for applications like the coiled cochlea of the inner ear, where planar, stiff, and nonconformable probes can hardly be used, transitioning from commonly used stiff glass fibers to flexible probes is required, especially for long-term use. Following this demand, polydimethylsiloxane (PDMS) with its lower Young's modulus compared to glass fibers can serve as material of choice. Hence, the long-term usability of PDMS as a waveguide material with respect to variations in transmission and refractive index over time is investigated. Different manufacturing methods for PDMS-based flexible waveguides are established and compared with the aim to minimize optical losses and thus maximize optical output power. Finally, the waveguides with lowest optical losses (-4.8dB cm-1 ± 1.3dB cm-1 at 472nm) are successfully inserted into the optogenetically modified cochlea of a Mongolian gerbil (Meriones unguiculatus), where optical stimuli delivered by the waveguides evoked robust neuronal responses in the auditory pathway.

Design and Analysis of Micro Signal Detection Circuit for Magnetic Field Detection Utilizing Coil Sensors

Eddy current inspection has been extensively employed in non-destructive testing of various conductive materials. The coil probe, as a mainstream sensor in the eddy current detection system, inevitably encounters interference from external signals while transmitting its own signal. Therefore, developing techniques to extract valuable signals from noisy ones is crucial for ensuring accurate detection. Carbon fiber composites not only possess significantly lower electrical conductivity compared to conventional metallic materials but also exhibit notable anisotropy. To address this issue, we designed an ‘8’ coil probe set where the excitation coil does not electromagnetically interfere with the detection coil. However, practical applications that require portability and miniaturization pose challenges when utilizing this coil probe set to identify carbon content or defects due to the typically weak output signal. To address this issue, this paper proposes a design that combines the ‘8’ structure of the planar coil probe with the principle of phase-locked amplification to create a dual-phase sensitive phase-locked amplification detection circuit. These specific design ideas were tested using a weak signal, which passed through the preamplifier, secondary amplifier, and band-pass filter comprising the target channel for signal amplification and noise filtering. The effective signal amplitude is proportional to the inverse phase difference between the direct current (DC) signal and inversely proportional to the amplitude of the signal. Finally, the DC signal was passed through an analog-to-digital converter (ADC). The analog-to-digital converter (A/D) is used to collect and calculate the DC signal, enabling the detection of weak electrical signals. Simulation experiments demonstrated that the signal detection circuit has an amplitude error below 0.2% and a phase error below 0.5%. The phase-locked amplification circuit designed in this paper can effectively extract the tiny impedance change signals of the planar coil sensor probe with high sensitivity and good robustness.

Small deviations between planned and performed bone cuts using a CT-based robotic-arm-assisted total knee arthroplasty system.

Computed tomography (CT)-based robotic system for total knee arthroplasty (TKA) has shown improved accuracy compared to conventional. This study was designed to(1) confirm the accuracy of the robotic system in achieving the planand (2) establish the alignment and positioning deviation between final components and planning, by measuring the discrepancy between final implant alignment and the corresponding planned cut. Ninety-six cementless robotic-arm assisted (RA) TKAs were assessed. Bone resections were performed using the haptically controlled robotic arm. Alignment in the coronal and sagittal plane and resection depth of the distal femoral and proximal tibial cuts were recorded with a navigation planar probe. After final components were impacted, the probe was positioned on each implant surface to determine its alignment and positioning. The mean tibial resections and implanted tibial component's positioning were 0.4 mm (standard deviation, SD: 0.6) and 0.9 mm (SD: 0.8), respectively, higher than planned (p < 0.01). The tibial sagittal cut had 19/96 cases (19.8%) of ±1° outliers from plan. In 40/96 cases (41.7%), the tibial component was more prominent than planned of more than 1 mm. The mean femoral resections and impacted femoral component's positioning was 0.1 mm (SD: 0.8) and 0.2 mm (SD: 0.7), respectively, higher than planned. In 23/96 cases (24.0%), the femoral sagittal cut and femoral component coronal alignment deviated more than ±1° from plan. The computed tomography-based robotic-assisted TKA system showed good accuracy regarding bone preparation and component's positioning relative to the planning. Cementless tibial component impaction resulted in the most deviation from plan, with a large proportion of cases resulting in being more prominent than planned. Level III.

Investigation of the directional Faraday cup and improvement of the comparison between direct and indirect thrust measurements of a magnetic nozzle ECR thruster

The thrust of an electric propulsion device estimated from electrostatic probe measurements may be different from direct thrust measurements. In order to reduce this discrepancy for electron cyclotron resonance thrusters (ECRT), a new diagnostic is presented: the directional Faraday cup (FCDi). Thanks to a peculiar design, it assesses the angular distribution of ion current density in the plume of plasma thrusters. First, a theoretical model of the angular selectivity of the FCDi is introduced. It is validated with both simulations and experiments. Guidelines are given to use the FCDi in the plume of ECRT. Second, the observed discrepancies between direct thrust measurements made on a thrust stand and indirect ones are reduced when using the FCDi instead of a planar Faraday probe with a guard ring (FPGR). Relative errors come down to 10% with the FCDi, which are compared to 20%–30% observed with the FPGR. An analysis demonstrates that it is not due to the effect of local ion trajectories but comes from the magnitude of the ion current measured. A large sheath in front of the negatively biased FPGR seems to be the cause of this phenomenon. The grounded opening of the FCDi reduces this phenomenon and improves the ion flux measurement accuracy. This new probe, with angular selectivity characteristics, allows for the comparison of the ion flux ejection direction with the magnetic field line and contributes to a better description of ion population dynamic in the magnetic nozzle of the thruster.

In Vivo Characterization of Intracortical Probes with Focused Ion Beam-Etched Nanopatterned Topographies.

(1) Background: Intracortical microelectrodes (IMEs) are an important part of interfacing with the central nervous system (CNS) and recording neural signals. However, recording electrodes have shown a characteristic steady decline in recording performance owing to chronic neuroinflammation. The topography of implanted devices has been explored to mimic the nanoscale three-dimensional architecture of the extracellular matrix. Our previous work used histology to study the implant sites of non-recording probes and showed that a nanoscale topography at the probe surface mitigated the neuroinflammatory response compared to probes with smooth surfaces. Here, we hypothesized that the improvement in the neuroinflammatory response for probes with nanoscale surface topography would extend to improved recording performance. (2) Methods: A novel design modification was implemented on planar silicon-based neural probes by etching nanopatterned grooves (with a 500 nm pitch) into the probe shank. To assess the hypothesis, two groups of rats were implanted with either nanopatterned (n = 6) or smooth control (n = 6) probes, and their recording performance was evaluated over 4 weeks. Postmortem gene expression analysis was performed to compare the neuroinflammatory response from the two groups. (3) Results: Nanopatterned probes demonstrated an increased impedance and noise floor compared to controls. However, the recording performances of the nanopatterned and smooth probes were similar, with active electrode yields for control probes and nanopatterned probes being approximately 50% and 45%, respectively, by 4 weeks post-implantation. Gene expression analysis showed one gene, Sirt1, differentially expressed out of 152 in the panel. (4) Conclusions: this study provides a foundation for investigating novel nanoscale topographies on neural probes.

A study of the formation of fuzzy tungsten in a HiPIMS plasma system

Nanostructured ‘fuzzy’ tungsten has been grown for the first time in a high-power impulse magnetron sputtering high power-impulse magnetron sputtering-(HiPIMS) system. The fuzzy layers were formed over range of surface temperatures T s, from 1025 to 1150 K, for helium ion fluences of 5.02 × 1024 m−2, and mean ion bombardment energy of 55 eV. The time-evolution of the helium ion flux (ΓHe) and incident energy (E He) were determined during the HiPIMS pulse (of width of 150 μs) using a planar Langmuir probe. The micrographic findings revealed that, the thickness of HiPIMS-grown nano-tendrill layers increased by 83% (from 274 to 501 nm) for only a 125 K rise in T s. This result is explained by the fact that higher surface temperatures led to larger helium bubbles which ultimately produce a thicker nanostructured layer. The growth rate of fuzzy tungsten layers in HiPIMS conditions is approximately 50% lower than those observed for DC magnetron operation.

Low-density plasmas generated by electron beams passing through silicon nitride window

In general, more attention is paid to how to improve the characteristic parameters of plasma in plasma applications. However, in some cases, it is necessary to produce plasma with low-electron density, such as in the laboratory simulation of ionospheric plasma in space science. In this study, a low-density plasma is generated by electron beams passing through a silicon nitride transmission window under low pressure condition. The transmission properties of electron beam passing through silicon nitride films are investigated by Monte Carlo simulation, and the plasma feature is studied by a planar Langmuir probe and a digital camera. It is found that the plasma exhibits a conical structure with its apex located at the transmission window. At a constant pressure, the cone angle of conical plasma decreases with the electron energy increasing. This is qualitatively consistent with the Monte Carlo simulation result. The frequency of electron-neutral collisions increases as the working pressure rising, which leads the plasma cone angle to increase. When the beam current is reduced from 10 μA to 0.5 μA at 40 keV, the electron density decreases, in a range between 10&lt;sup&gt;5&lt;/sup&gt; and 10&lt;sup&gt;6&lt;/sup&gt; cm&lt;sup&gt;–3&lt;/sup&gt;, while the electron temperature does not change significantly but approaches 1 eV. It can be inferred that the electron density decreases with the distance &lt;i&gt;z&lt;/i&gt; from the transmission window in the incident direction of the electron beam. A low-density plasma of less than 10&lt;sup&gt;5&lt;/sup&gt; cm&lt;sup&gt;–3&lt;/sup&gt; can be obtained further away from the transmission window.

Wall material effects in a minimized electron cyclotron resonance ion thruster

Wall material effects in micro-ion thrusters attracts significant research attention with respect to weakening plasma wall loss, and increasing propellant utilization to obtain high-precision and low-thrust of micro-Newton propulsion, as required in new generation space observation missions. In this study, we compare the performance and discharge characteristics of different wall materials, namely, Mo and Al2O3 in a minimized electron cyclotron resonance ion thruster. The results show that the propellant utilization and specific impulse of the ceramic are about three times higher than those of the Mo at a low mass flow rate of 0.03 sccm. In addition, a planar Langmuir probe is used in the discharge chambers, and the results show that the secondary electron emission of Al2O3 effectively reduces the electron temperature, increases the electron density, and results in high efficiency. These results are helpful for improving the performance of micro-ion propulsion devices for microsatellites and space-borne gravitational wave detection missions.

Dynamic ultrasound focusing and centimeter-scale ex vivo tissue ablations with a CMUT probe developed for endocavitary HIFU therapies.

Thermal ablation of localized prostate tumors via endocavitary Ultrasound-guided High Intensity Focused Ultrasound (USgHIFU) faces challenges that could be alleviated by better integration of dual modalities (imaging/therapy). Capacitive Micromachined Ultrasound Transducers (CMUTs) may provide an alternative to existing piezoelectric technologies by exhibiting advanced integration capability through miniaturization, broad frequency bandwidth and potential for high electro-acoustic efficiency. An endocavitary dual-mode USgHIFU probe was built to investigate the potential of using CMUT technologies for transrectal prostate cancer ablative therapy. The USgHIFU probe included a planar 64-element annular HIFU CMUT array (fHIFU = 3 MHz) surrounding a 256-element linear imaging CMUT array. Acoustic characterization of the HIFU array included 3D pressure field mapping and radiation force balance measurements. Ex vivo proof-of-concept experiments consisted in generating HIFU thermal ablations with the CMUT probe on porcine liver tissues. The planar CMUT probe enabled HIFU dynamic focusing (distance range: 32 - 72 mm) while providing acoustic surface intensities of 1 W/cm2 that allowed producing elementary ex vivo ablations in depth of liver tissue (L×W ≈ 10 mm × 5 mm). Combinations of dynamic focusing, along with probe rotation and translation produced larger thermal ablations (L×W ≈ 20 mm × 20 mm) by juxtaposing multiple elementary ablations, consistent with expected results obtained through numerical modeling. The technical feasibility of using a USgHIFU probe, fully-developed using CMUTs for tissue ablation purposes, was demonstrated. The HIFU-CMUT array showed tissue ablation capabilities with volumes compatible with localized cancer targeting thus providing assets for further development of focal therapies.

Amorphous TiO2-Au thin film composites synthesized by pulsed laser deposition

TiO2 has been widely studied and synthesized by various methods due to its excellent optoelectronic properties. It is possible to modify the optical properties of TiO2 by incorporating noble metal nanoparticles in order to improve its photoresponse. In this work, TiO2-Au thin film composites were grown by pulsed laser deposition technique. Ti and Au targets were simultaneously ablated in order to produce combined plasmas under a reactive atmosphere containing oxygen at a pressure of 2×10-2 Torr. The plasmas were analyzed individually by means of a planar Langmuir probe in order to calculate their mean kinetic ion energy and plasma density. Ti plasma parameters were kept constant at 196 eV and 2.06×1013 cm-3 while the Au plasma density was varied from 2.65×1012 cm-3 to 22.4×1012 cm-3. The samples were characterized by UV-Vis spectroscopy and scanning electron microscopy. The band gap of the films was determined by means of the Tauc method, which decreased from 2.36 to 1.54 eV as the Au plasma density increased. The resultant morphology of the films shows the formation of spherical Au nanoparticles, whose average sizes increases as the Au plasma density increased, resulting in values ranging from 15 to 72 nm.

PICOSECOND PULSED LASER DEPOSITION OF MOS2 THIN FILMS

MoS2 thin films were grown by the pulsed laser deposition technique using a picosecond laser at a wavelength of 1030 nm. The plasma ion mean kinetic energy and density were estimated from the time-of-flight distributions measured using a Langmuir planar probe. It has been found that the mean kinetic energy decreases with increasing the laser pulse energy. This unusual effect is explained by the difference in the volatility of the vaporized species. Samples were structurally characterized by Raman spectroscopy and grazing angle X-ray diffraction. It was found that thin films of amorphous matrices containing MoS2 nanocrystallites were grown. Optical characterization carried out by UV-vis spectroscopy yielded transmittance values above 90% in the visible spectral range and an indirect electronic transition at 1.4 eV. Chemical oxidation states for molybdenum and sulfur were analyzed by means of X-ray photoelectron emission spectroscopy, which revealed Mo-S bonding states, confirming the growth of MoS2.

Effect of composite vortex beam on a two-dimensional gain assisted atomic grating

We propose an atomic grating based on an electromagnetically induced transparency phenomenon that switches between zeroth-order diffraction to a distinct higher-order diffraction pattern by driving a planar gaseous medium of a four-level tripod () atoms with three laser beams: modulation of standing wave control beam propagating nearly perpendicular to the planar medium, while vortex and weak plane probe beams directed perpendicular to the medium. We numerically investigate the behavior of the amplitude, phase modulations, and probe field diffraction intensities of different orders by the variation of the field detunings and orbital angular momentum number of the composite vortex light beam. Specifically, in the off-resonant case, the interplay between a square lattice of the control and an additional spatial variation of the vortex beam allows the emergence of higher diffraction orders and variable gain due to double transparency windows in this complex optical system. We believe that our proposed scheme might be useful in optical memory devices via the storage of information to diffraction orders of the atomic grating.

A Wideband Cavity-Backed Dual-Polarized Antenna for X-Band Applications

In this letter, a cavity-backed dual-polarized antenna operating in X-Band (8–12 GHz) is presented. The antenna is composed of a metal cavity with a circular slot, a dual-polarized feeding balun structure printed on a single-layer substrate, and a loaded dielectric block. The units of the antenna are fixed by screws, and no additional welding assembly is required. By setting notches structure on the dual-polarized planar feeding probes, the port isolation and polarization purity of the proposed antenna have been significantly improved. A prototype with the compact size of 0.44 × 0.44 × 0.39 λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0</sub> (λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0</sub> is the wavelength at 10 GHz) is fabricated and measured. Measured results demonstrate the return losses are lower than 10 dB and the isolations are greater than 23 dB from 8 to 12 GHz, the measured bore-sight gains vary from 4.5 to 5.8 dBi, and the cross-polarization levels less than −20 dB are obtained within the operational band.

Microwave NDT of Smart Composite Structures with Embedded Antennas

The integration of antennas in composite structures is gaining popularity with advances in wireless communications and the ever-increasing demands for efficient smart structures. Efforts are ongoing to ensure that antenna-embedded composite structures are robust and resilient to inevitable impacts, loading and other external factors that threaten the structural integrity of these structures. Undoubtedly, the in situ inspection of such structures to identify anomalies and predict failures is required. In this paper, the microwave non-destructive testing (NDT) of antenna-embedded composite structures is introduced for the first time. The objective is accomplished using a planar resonator probe operating in the UHF frequency range (~525 MHz). High-resolution images of a C-band patch antenna fabricated on an aramid paper-based honeycomb substrate and covered with a glass fiber reinforced polymer (GFRP) sheet are presented. The imaging prowess of microwave NDT and its distinct advantages in inspecting such structures are highlighted. The qualitative as well as the quantitative evaluation of the images produced by the planar resonator probe and a conventional K-band rectangular aperture probe are included. Overall, the potential utility of microwave NDT for the inspection of smart structures is demonstrated.