Relative Placement Research Articles

Effect of soft magnetic particles content on multi-physics field of magnetorheological composite gel clutch with complex flow channel excited by Halbach array arrangement

In this paper we investigate the influence of soft magnetic particle mass fraction on the multi-physics field of proposed magnetorheological (MR) gel clutch. A novel MR gel clutch with complex cup-shaped gap is described, whose performance is based on the relative placement between Halbach array arrangement and MR gel. Smart MR gel with 40 wt%, 50 wt%, 60 wt%, 70 wt% and 80 wt% of soft magnetic particles used as the transfer medium and Halbach array is adopted as magnetic excitation system. Its magnetic/mechanical analysis is carried out based on Bingham-plastics model using COMSOL Multiphysics software, which takes into account the variation of dynamic viscosity with magnetic flux density. The distribution of the magnetic flux density, shear yield stress, post-yield viscosity, shear stress and torque in the four flow channels during the transition from engagement state to disengagement state are obtained and analyzed in detail. Multi-physics field characteristics of proposed MR gel clutch with five kinds of MR gels are studied and compared in order to give some useful suggestions in the design phase. Finally, the dynamic torque of the MR clutch with different MR gel is experimentally evaluated.

Investigation on piezoresistive properties of reduced graphene oxide treated glass textiles based multifunctional sensors

AbstractGlass fabric‐reinforced composites (GFRC) and other revolutionary engineered materials find extensive application in the aerospace, construction, and automobile sectors. It is challenging to predict damage under real‐time stresses due to the anisotropic behavior of composite materials. This study presents the development of a glass textile‐based multifunctional composite sensor and demonstrates its application as a change in resistance or gauge factor in structural health monitoring (SHM) systems. This sensor is coated with reduced graphene oxide (rGO) nanomaterial. Its electrical resistance is evaluated by examining the concentration of nanoparticles and varying geometrical parameters. A three‐point bending method assessed the piezoresistive behavior of the integrated sensor in the GFRC. The impact of sensor width and relative placements in the material's thickness direction within the composite samples is evaluated. Cyclic flexural testing was also performed to demonstrate real‐world applications. The research concludes that it can be utilized as a damage assessment technique for GFRC. The developed sensor can be used to provide an electrically conductive path or as a resistor in the field of E‐textiles. The developed piezoresistive sensor has the flexibility to be used as a multifunctional sensor for multiple purposes, such as force, torque, weight, pressure, flow, acceleration sensors, etc.Highlights Glass textile‐based multifunctional materials are reported as strain‐monitoring sensors. Tailored sensor resistance could be achieved through rGO current conduction paths. Glass textile‐based sensors could potentially be used in the field of E‐textile.

Early placement of a non-invasive, pressure-regulated, fascial reapproximation device improves reduction of the fascial gap in open abdomens: a retrospective cohort study

BackgroundSince current fascial traction methods involve invasive procedures, they are generally employed late in the management of the open abdomen (OA). This study aimed to evaluate early versus late placement...

Admixture in the fungal pathogen Blastomyces.

Blastomyces is an emerging primary fungal pathogen that affects patients worldwide. The evolutionary processes that have resulted in the current diversity in the genus remain largely unexplored. We used whole genome sequences from 99 Blastomyces isolates, including two sequenced in this study using long-read technologies, to infer the phylogenetic relationships between Blastomyces species. We find that five different methods infer five different phylogenetic trees. Additionally, we find gene tree discordance along the genome with differences in the relative phylogenetic placement of several species of Blastomyces, which we hypothesize is caused by introgression. Our results suggest the urgent need to systematically collect Blastomyces samples around the world and study the evolutionary processes that govern intra- and interspecific variation in these medically important fungi.

Gentamicin and clindamycin antibiotic-eluting depot technology eradicates S. aureus in an implant-associated osteomyelitis pig model without systemic antibiotics.

The therapeutic challenges of orthopedic device-related infections and emerging antimicrobial resistance have attracted attention to drug delivery technologies. This study evaluates the preclinical efficacy of local single- and dual-antibiotic therapy against implant-associated osteomyelitis (IAO) using a drug-eluting depot technology, CarboCell, that provides sustained release of high-dose antibiotics and allows for strategic in situ placement in relation to infectious lesions. Clindamycin and gentamicin were formulated in CarboCell compositions. One-stage-revision of tibial Staphylococcus aureus IAO was conducted in 19 pigs. Pigs were treated locally with CarboCell containing either gentamicin alone for 1 week or a co-formulation of gentamicin and clindamycin for 1 or 3 weeks. Bone, soft tissue, and antibiotic depots were collected for microbiology, histology, and HPLC analyses. Supporting in vivo release studies of CarboCell formulations were performed on mice. Both single- and dual-antibiotic CarboCell formulations were developed and capable of eradicating the infectious bacteria in bone and preventing colonization of implants inserted at revision. Eradication in soft tissue was observed in all pigs after 3 weeks and in 6/9 pigs after 1 week of treatment. Neutrophil counts in bone tissue were below the infection cut-off in all pigs receiving the dual-antibiotic therapies, but above in all pigs receiving the single-antibiotic therapy. Histological signs of active bone reorganization and healing were observed at 3 weeks. In conclusion, all CarboCell formulations demonstrated strong therapeutic activity against IAO, eradicating S. aureus in bone tissue and preventing colonization of implants even without the addition of systemic antibiotic therapy.

Less Is More: The Role of Mesh in Microsurgical Breast Reconstruction with Abdominal Flaps.

The use of mesh to reinforce the abdominal wall after abdominal flap harvest has been reported to decrease the risk of bulging and herniation. However, the impact of the plane of mesh placement in relation to the anterior rectus sheath (vs. no mesh) on postoperative abdominal complications remains unclear. We retrospectively analyzed the length of stay and clinical outcomes in 158 female patients who underwent breast reconstruction with 250 free abdominal flaps. Group 1 consisted of patients who underwent polypropylene sublay-onlay ("sandwich") mesh placement (N = 70) versus polypropylene sublay-only mesh (group 2; N = 54) versus primary fascial repair without mesh (group 3; N = 34). Patient demographics and comorbidities were comparable between study groups, except for rates of neoadjuvant chemotherapy (group 1: 53% vs. group 2: 33% vs. group 3: 24% [p < 0.01]), postoperative follow-up in months (group 1: 21.5; group 2: 11.5; group 3: 7.6 [p < 0.01]), and length of stay in days (group 1: 4.9 vs. group 2: 4.4 vs. group 3: 3.3 [p < 0.01]). No differences were observed in breast flap and donor-site complications between study groups. Patients in group 3 required significantly lower oral morphine equivalent units postoperatively compared with those in groups 1 and 2 (group 1:185.5 vs. group 2: 79.7 vs. group 3: 71.6 [p < 0.01]). Abdominal donor-site closure without mesh was associated with a shorter length of stay and less narcotic intake without an increase in donor-site complications. These findings should be considered when deciding to place mesh for donor-site closure after abdominal flap harvest.

The role of spinal cord neuroanatomy in the variances of epidural spinal recordings

BackgroundSpinal cord stimulation (SCS) has demonstrated multiple benefits in treating chronic pain and other clinical disorders related to sensorimotor dysfunctions. However, the underlying mechanisms are still not fully understood, including how electrode placement in relation to the spinal cord neuroanatomy influences epidural spinal recordings (ESRs). To characterize this relationship, this study utilized stimulation applied at various anatomical sections of the spinal column, including at levels of the intervertebral disc and regions correlating to the dorsal root entry zone.MethodTwo electrode arrays were surgically implanted into the dorsal epidural space of the swine. The stimulation leads were positioned such that the caudal-most electrode contact was at the level of a thoracic intervertebral segment. Intraoperative cone beam computed tomography (CBCT) images were utilized to precisely determine the location of the epidural leads relative to the spinal column. High-resolution microCT imaging and 3D-model reconstructions of the explanted spinal cord illustrated precise positioning and dimensions of the epidural leads in relation to the surrounding neuroanatomy, including the spinal rootlets of the dorsal and ventral columns of the spinal cord. In a separate swine cohort, implanted epidural leads were used for SCS and recording evoked ESRs.ResultsReconstructed 3D-models of the swine spinal cord with epidural lead implants demonstrated considerable distinctions in the dimensions of a single electrode contact on a standard industry epidural stimulation lead compared to dorsal rootlets at the dorsal root entry zone (DREZ). At the intervertebral segment, it was observed that a single electrode contact may cover 20-25% of the DREZ if positioned laterally. Electrode contacts were estimated to be ~0.75 mm from the margins of the DREZ when placed at the midline. Furthermore, ventral rootlets were observed to travel in proximity and parallel to dorsal rootlets at this level prior to separation into their respective sides of the spinal cord. Cathodic stimulation at the level of the intervertebral disc, compared to an ‘off-disc’ stimulation (7 mm rostral), demonstrated considerable variations in the features of recorded ESRs, such as amplitude and shape, and evoked unintended motor activation at lower stimulation thresholds. This substantial change may be due to the influence of nearby ventral roots. To further illustrate the influence of rootlet activation vs. dorsal column activation, the stimulation lead was displaced laterally at ~2.88 mm from the midline, resulting in variances in both evoked compound action potential (ECAP) components and electromyography (EMG) components in ESRs at lower stimulation thresholds.ConclusionThe results of this study suggest that the ECAP and EMG components of recorded ESRs can vary depending on small differences in the location of the stimulating electrodes within the spinal anatomy, such as at the level of the intervertebral segment. Furthermore, the effects of sub-centimeter lateral displacement of the stimulation lead from the midline, leading to significant changes in electrophysiological metrics. The results of this pilot study reveal the importance of the small displacement of the electrodes that can cause significant changes to evoked responses SCS. These results may provide further valuable insights into the underlying mechanisms and assist in optimizing future SCS-related applications.

Laparoscopic cholecystectomy and laparoscopic common bile duct exploration for cholecystolithiasis and choledocholithiasis in a patient with situs inversus totalis: A case report

AbstractSitus inversus complicates diagnosis and treatment due to the mirrored organ placement in relation to normal anatomy. This report describes a 78‐year‐old female patient with situs inversus totalis who underwent laparoscopic cholecystectomy and laparoscopic common bile duct exploration for cholecystolithiasis and choledocholithiasis. Utilizing the “French mirror technique” for port placement, the surgeon adeptly mirrored standard maneuvers with a 2‐mm needle forceps in the left hand and a 5‐mm forceps in the right in a reversed anatomical setting. This technique maintained familiar hand movements, despite the patient's unique anatomy. The surgeon applied transcystic ductal bile duct exploration, using choledochoscopy for duct exploration and a basket catheter for stone removal. Laparoscopic cholecystectomy and common bile duct exploration through the transcystic ductal route are viable and effective for patients with situs inversus.

Composite structures with embedded fiber optic sensors: A smart propellant tank for future spacecraft applications

Modern spacecraft and launch vehicle design is more oriented towards reducing system-level design and assembly complexities. In order to maintain high overall system performance while reducing these complexities, the use of smart materials and smart structural components is a well-known practice and is currently of rising interest to space systems' designers. The paper discusses a concept of smart space structures, in particular, a carbon fiber composites structure embedded with Optical Fiber Sensors (OFS) for spacecraft and launch vehicle applications. This study highlights the operational requirements for such tank and the smart features enabled by the optical fiber sensors. For the latter aspect, a quantitative comparison between Fiber Bragg Grating sensors (FBGs) and Distributed Optical Fiber Sensors (DOFS) based on Optical Frequency Domain Reflectometry (OFDR) is presented to state their core performance parameters, such as the sensitivity, sensing range, dynamic measurement capability, and spatial resolution. The increased performance and reliability in harsh environments associated with fiber optic sensors come with a reduction in size, mass, and power consumption compared to the conventional electronic sensors. Optical fiber sensors embedded in carbon fiber structures have proven their capability in providing accurate real-time measurements of temperature and monitoring structural integrity while detecting precisely possible points of rupture and failure as discussed and demonstrated in the literature review. The applications of fiber optic sensing in smart propellant tanks may extend to detecting fluid leakage, also providing increased precision in propellant gauging through temperature mapping, and can be used in on-ground qualification, pre-flight testing, as well as in-orbit operation, condition, and structural health monitoring. The article presents a statement for an optimal FOS embedding approach in composite pressure vessels and discusses the related placement and orientation method for the fiber optic sensors, coupled with a one component simplified analytical stress-strain transfer model deriving the stress component along the maximum principal direction (i.e., σMaxPrincipal). The novel approach is believed to serve the optimal employment of embedded FOS in composite structures, e.g., pressure vessels and light-weight structures in spacecraft, among other applications. The simplified model is believed to pave the way for effective data interpretation and processing, utilizing the available limited computational resources on-board the spacecraft.

Research on the Relative Placement Angle of the Induction Heater and the Channel in a Four-Channel Induction-Heating Tundish.

In order to optimize the application effect of induction heating (IH) tundishes, a four-channel IH tundish is taken as the research object. Based on numerical simulation methods, the influence of different relative placement angles of induction heaters and channels on the electromagnetic field, flow field and temperature field of the tundish is investigated. We focus on comparing the magnetic flux density (B) and electromagnetic force (EMF) distribution of the channel. The results show that regardless of the relative placement angle between the heater and the channel, the distribution of B in the central circular cross-section of the channel is eccentric. When the heater rotates around channel 1 towards the bottom of the tundish, the distribution of B in the central circular cross-section of the channel changes from a horizontal eccentricity to a vertical one. Through the analysis of the B contour in the longitudinal section of the channel, the difference in effective magnetic flux density area (ΔAB) between the upper and lower parts of the channel can be obtained, thereby quantitatively analyzing the distribution of B in this section. The distribution pattern of ΔAB is consistent with the distribution pattern of the electromagnetic force in the vertical direction (FZ) of the channel centerline. The ΔAB and FZ of channel 1 gradually increase as the heater rotates downwards, while those of channel 2 reach their maximum value at a rotation angle of 60°. Compared to the conventional placement, when the heater rotation angle is 60°, the outlet flow velocities at channel 1 and channel 2 decrease by 15% and 12%, respectively. However, the outlet temperature at channel 2 increases by 1.96 K, and the molten steel flow at the outlet of channel 1 and channel 2 no longer exhibits significant downward flow. This shows that when the heater rotation angle is 60°, it has a dual advantage. On the one hand, it is helpful to reduce the erosion of the molten steel on the channel and the bottom of the discharging chamber, and on the other hand, it can more effectively exert the heating effect of the induction heater on the molten steel in the channel. This presents a new approach to enhance the application effectiveness of IH tundish.

Tunable Optical Anisotropy in Rare-Earth Borates with Flexible [BO3] Clusters.

Borates have garnered a lot of attention in the realm of solid-state chemistry due to their remarkable characteristics, in which the synthesis of borates with isolated [BO3] by adding rare-earth elements is one of the main areas of structural design study. Five new mixed-metal Y-based rare-earth borates, Ba2ZnY2(BO3)4, KNa2Y(BO3)2, Li2CsY4(BO3)5, LiRb2Y(BO3)2, and RbCaY(BO3)2, have been discovered using the high-temperature solution approach. Isolated [BO3] clusters arranged in various configurations comprise their entire anionic framework, allowing for optical anisotropy tuning between 0.024 and 0.081 under 1064 nm. In this study, we characterize the relative placements of their [BO3] groups and examine how their structure affects their characteristics. The origin of their considerable optical anisotropy has been proven theoretically. This study unequivocally demonstrates that even a slight alteration to borates' anionic structure can result in a significant improvement in performance.

A boundary element method of bidomain modeling for predicting cellular responses to electromagnetic fields

Objective. Commonly used cable equation approaches for simulating the effects of electromagnetic fields on excitable cells make several simplifying assumptions that could limit their predictive power. Bidomain or ‘whole’ finite element methods have been developed to fully couple cells and electric fields for more realistic neuron modeling. Here, we introduce a novel bidomain integral equation designed for determining the full electromagnetic coupling between stimulation devices and the intracellular, membrane, and extracellular regions of neurons. Approach. Our proposed boundary element formulation offers a solution to an integral equation that connects the device, tissue inhomogeneity, and cell membrane-induced E-fields. We solve this integral equation using first-order nodal elements and an unconditionally stable Crank–Nicholson time-stepping scheme. To validate and demonstrate our approach, we simulated cylindrical Hodgkin–Huxley axons and spherical cells in multiple brain stimulation scenarios. Main Results. Comparison studies show that a boundary element approach produces accurate results for both electric and magnetic stimulation. Unlike bidomain finite element methods, the bidomain boundary element method does not require volume meshes containing features at multiple scales. As a result, modeling cells, or tightly packed populations of cells, with microscale features embedded in a macroscale head model, is simplified, and the relative placement of devices and cells can be varied without the need to generate a new mesh. Significance. Device-induced electromagnetic fields are commonly used to modulate brain activity for research and therapeutic applications. Bidomain solvers allow for the full incorporation of realistic cell geometries, device E-fields, and neuron populations. Thus, multi-cell studies of advanced neuronal mechanisms would greatly benefit from the development of fast-bidomain solvers to ensure scalability and the practical execution of neural network simulations with realistic neuron morphologies.

Morphological variability of lateral femoral cutaneous nerve and its potential clinical significance.

The lateral femoral cutaneous nerve is derived from the dorsal branches of the L2 and L3 spinal nerves. It travels across the pelvis and heads towards the anterior superior iliac spine. It passes under the lateral part of the inguinal ligament and then divides into two branches, which are responsible for sensory innervation of the anterolateral and lateral skin of the thigh. However, the course of this nerve can vary morphologically. Numerous differences have been observed in its exit from the pelvis and in the number of its main trunks and branches. Additionally, its angle with the inguinal ligament and its placement in relation to other structures (such as the femoral artery, femoral nerve, and the sartorius and iliacus muscles) also vary. All of these variants have potential clinical implications. Therefore, the aim of this review is to present the morphological variability of the lateral cutaneous nerve and to explore how these anatomical differences can introduce clinical concerns. Presented review of the literature was written based on over 30 studies. Comprehensive literature search was done using PubMed in order to study the morphological variability of lateral femoral cutaneous nerve (LFCN). To be included in this review studies needed to be meet certain criteria: been published before December 2023, present information valuable to this paper (variability of lateral femoral cutaneous nerve/clinical significance). The search included how LFCN vary either among fetuses and adults in the aim of providing more complex information about the variability of this nerve. During the search key words as following were used. No particular references were excluded from the analysis. All relevant studies were included, and citation tracking was used to identify publications. This review presents the description of variability of LFCN and its potential clinical impact. In the review differences in adult and fetuses were considered, morphological variability were divided into 4 groups: the origin of the nerve, the way it leaves the pelvis, the branching pattern, the angle between LFCN and surrounding structures and then, clinical significance were considered basing on available literature.

Spacing of subsurface poultry litter bands: Influence on maize performance and nitrogen use efficiency

AbstractPoultry litter (PL) is traditionally surface broadcast to no‐till maize (Zea mays L.). PL is nutrient‐dense, and surface‐applied PL nitrogen (N) is vulnerable to losses to the atmosphere and water systems. An application method was developed by USDA‐ARS scientists for shallow subsurface banding PL to reduce ammonia (NH3) volatilization and surface runoff. There is limited information on how this application method will affect conservation and nutrient accessibility in no‐till maize. The objectives were to determine if adjusting PL lateral subsurface band placement in relation to maize rows affects nutrient use and maize yields. Treatments were a nontreated control (NTC), urea ammonium nitrate surface banded (Fert), poultry litter surface broadcast (PLBr), and three subsurface banded PL treatments. The subsurface PL treatments were one (PLSub1), two (PLSub2), or three (PLSub3) bands between maize rows. Treatments receiving N were applied at 180 kg total N ha−1. Nitrogen concentration in V4 aboveground dry matter was higher in PLSub1 than PLSub2. Aboveground dry matter yields for all PLSub treatments were greater than PLBr and comparable to Fert. The PLSub1 and PLSub2 treatments resulted in maize grain yields equivalent to Fert and greater than PLBr and NTC when averaged across years. Few differences were observed in postharvest soil sample nutrient concentrations between PLSub treatments. These results suggest that subsurface banding PL can conserve N and increase no‐till maize yield over traditional surface broadcast PL; however, increasing the frequency of subsurface PL bands did not clearly affect nutrient conservation or accessibility to the maize.

Improvement of the methodology for calculating the expected drilling speed with PDC chisels

Purpose. Determination of the dependence of the depth of penetration of the PDC cutter into the bottom hole rock, taking into account its geometric parameters and spatial placement in relation to the destroyed array. Methodology. The tasks were solved by a comprehensive research method, including analysis and generalization of literary and patent sources, conducting theoretical research, which consists in solving the theoretical problem of the impact of a superhard circular cutter on an elastically fragile mountain range, using computer and mathematical modeling methods. Findings. A simplified expression has been obtained that allows taking into account the features of the PDC cutter with sufficient accuracy for engineering calculations when determining the depth of its penetration into the bottom hole rock. A method is proposed for calculating the depth of fracture in one revolution of a diamond carbide cutter PDC into the rock of the bottom of the well. The patterns of destruction by the proposed diamond-hard-alloy PDC chisel of a rock mass at the bottom of the well from the parameters of the drilling regime and the hardness of the drilled rocks have been established. Originality. For the first time, the dependence has been obtained of the influence of the geometric parameters of the shape of a single diamond-carbide PDC cutter and its spatial placement in the body of the bit matrix on the magnitude of the technological parameters of drilling a well, and their effect on the nature of the destruction of the array PDC cutter. Practical value. A technique for determining the depth of penetration of a single PDC cutter is proposed, the use of which will allow predicting the mechanical speed, depending on the geological and technical conditions of drilling wells. And taking into account the abrasive properties of rocks, it is possible to reduce the wear of the bits, and therefore the amount of necessary rock-crushing tools for the entire volume of drilling operations during the construction of the well.

Romanian presumptive in interaction: evidentiality and beyond

Abstract The paper emphasizes the pragmatic and discursive extensions of a special verbal structure – at its origin, a Future Tense form – known in Romanian linguistics as presumptive mood (hereinafter: PRESUMPT). In terms of evidentiality, the PRESUMPT has two types of meanings: an inferential meaning, expressing an inference-based supposition, and also a reportative meaning, when the utterer does not take responsibility for the truthfulness of information from another source. These significances are very subtle and closely related to their context of use. That is why, sometimes, it is very difficult to distinguish one value from another. Therefore, Romanian PRESUMPT deploys in discourse pragmatic enrichments depending on the syntactic-enunciative structure it is inserted in or on some other parameters, such as: speaker’s epistemic stance, genre of discourse, intersubjectivity, and extends its core meaning of evidentiality through a range of discursive dimensions. Considering this situation, our approach outlines that a complex rhetorical strategy is involved in such contexts, where the PRESUMPT actualizes in fact only its prototypical feature [+placement in a subsequent relation (“ultériorité” – see Bres 2012. Conditionnel et ultériorité dans le passé: De la subjectivité à l’objectivité. In SHS Web of Conferences, Volume 1 (3ème Congrès Mondial de Linguistique Française), 1719–1730.)], exclusively marking the relation of subsequence of the hypothesis or of the quoted speech act (in counter-argumentative frames) compared to a previously mentioned state of facts.

Radiation Patterns of RF Wireless Devices Implanted in Small Animals: Unexpected Deformations Due to Body Resonance.

One challenge in designing RF wireless bioelectronic devices is the impact of the interaction between electromagnetic waves and host body tissues on far-field wireless performance. In this article, we investigate a peculiar phenomenon of implantable RF wireless devices within a small-scale host body related to the deformation of the directivity pattern. Radiation measurements of subcutaneously implanted antennas within rodent cadavers show that the direction of maximum radiation is not always identical with the direction to the closest body-air interface, as one would expect in larger-scale host bodies. For an implanted antenna in the back of a mouse, we observed the maximum directivity in the ventral direction with 4.6 dB greater gain compared to the nearest body-air interface direction. Analytic analysis within small-scale spherical body phantoms identifies two main factors for these results: the limited absorption losses due to the small body size relative to the operating wavelength and the high permittivity of the biological tissues of the host body. Due to these effects, the entire body acts as a dielectric resonator antenna, leading to deformations of the directivity pattern. These results are confirmed with the practical example of a wirelessly powered 2.4-GHz optogenetic implant, demonstrating the significance of the judicious placement of external antennas to take advantage of the deformation of the implanted antenna pattern. These findings emphasize the importance of carefully designing implantable RF wireless devices based on their placements and relative electrical dimensions in small-scale animal models.

First considerations on the supporting structures of FCC-ee booster and collider in the arc regions

In 2022, the FCC Feasibility Study management mandated a working group to analyse the best configuration of the FCC-ee tunnel in the arc regions, in view of the construction of a mock-up of the arc half-cell. One of the main and most challenging goals of the study, named FCC-ee Arc Half-Cell Mock-up Project, was to perform a preliminary investigation on the principles of supporting the Short-Straight Sections and dipoles of the half-cells, both for the booster and for the collider machines. This is an important input needed for the choice of the best configuration of the relative placement of the booster with respect to the collider. The structural stiffness, mass and stability of the supporting structures must be optimized to minimize the vibrations transmitted/transferred to the magnetic system of the accelerators by elements such as pumps, water cooling system, beam thermomechanical stresses, powering elements, etc. To perform the study, tools such as CAD software, FEM and analytical techniques were employed. This paper summarizes the preliminary design concepts and the results of the simulations performed.

Impact of Soil Type and Placement of Xyway LFR Fungicide on Germination and Growth of Corn Seedlings Under a Controlled Setting

Xyway LFR was released for use in corn as an in-furrow fungicide during 2020. Producers have raised concerns of reduced emergence and growth in corn plantings. Here, I assessed the impact of Xyway LFR placement in relation to the seed for impacts on seedling emergence and growth in two contrasting soil types (sand versus topsoil) under controlled conditions. Soil was added to containers, and five corn seeds were placed in a row in a furrow within each container. Xyway LFR was applied in a band at labelled rates at 0 (directly on seed), 1.27, 2.54, or 5.08 cm away from the seed. Containers were maintained under a light bank, and germination over time, as well as seedling biomass, was assessed. Statistical analysis indicated that plants in topsoil had greater germination rates and dry masses than plants in sand. Total plant dry masses were reduced relative to controls when Xyway LFR was placed 0 cm from the seed. However, when placed 2.54 or 5.08 cm from the seed, this impact was not evident. Potential phytotoxic effects may be mitigated by placing the product in a band at least 2.54 cm from the seed furrow.

Accuracy Comparison between Robot-Assisted Dental Implant Placement and Static/Dynamic Computer-Assisted Implant Surgery: A Systematic Review and Meta-Analysis of In Vitro Studies.

Background and Objectives: The present systematic review and meta-analysis undertake a comparison of studies that examine the accuracy of robot-assisted dental implant placement in relation to static computer-assisted implant surgery (SCAIS), dynamic computer-assisted implant surgery (DCAIS), and freehand procedures. This study aims to provide a comprehensive understanding of the precision of robot-assisted dental implant placement and its comparative efficacy in relation to other placement techniques. Methods: The guidelines recommended by Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) were used to organize and compose this review. Four electronic databases (PubMed, Web of Science, Scopus, and Cochrane) were systematically searched for pertinent articles. Articles were selected following the inclusion and exclusion criteria. Qualitative and quantitative analyses of the selected articles were performed. Results: The initial electronic search resulted in 1087 hits. Based on the inclusion and exclusion criteria, five articles were selected for qualitative analysis, out of which three were considered for quantitative analysis. Three parameters were considered for accuracy evaluation (angular, coronal, and apical deviation). The mean angular deviation was -1.22 degrees (95% CI, -1.06--1.39), the mean coronal deviation was -0.15 mm (95% CI, -0.24--0.07), and the mean apical deviation was -0.19 mm (95% CI, -0.27--0.10). Conclusions: The robotic implant system was found to have significantly lower angular deviations and insignificantly lower coronal and apical deviations compared to DCAIS. Within the limitations of this review, it can be concluded that robot-assisted implant placement in resin models permits higher accuracy compared to DCAIS and SCAIS systems. However, due to the limited number of comparative studies with high heterogeneity, the findings of this review should be interpreted with caution. Further research is necessary to confirm the clinical application of robotics in implant surgery.