Photovoltaic Voltage Source Inverter Research Articles

Point of Common Coupling Voltage Modulated Direct Power Control of Grid-Tied Photovoltaic Inverter for AC Microgrid Application

A direct power control (DPC) approach is proposed in this study for a grid-tied photovoltaic (PV) voltage source inverter (VSI) to regulate active and reactive power flow directly in between utility grid and microgrid (MG) by controlling point of common coupling (PCC) voltage. The proposed PCC voltage modulated (PVM) theory-based DPC method (PVMT-DPC) is composed of nonlinear PVM, nonlinear damping, conventional feedforward, and feedback PI controllers. For grid synchronization rather than employing phase-locked-loop (PLL) technology, in this study, direct power calculation of the PCC voltage and current is adopted. Subsequently, at PCC, the computed real and reactive powers are compared with reference powers in order to generate the VSI’s control signals using sinusoidal pulse width modulation (SPWM). Because of the absence of the PLL and DPC method adoption, the suggested controller has a faster convergence rate compared to traditional VSI’s power controllers. Additionally, it displays nearly zero steady-state power oscillations, which assure that MG’s power quality is improved significantly. To validate the proposed PVMT-DPC method’s performance, real-time simulations are conducted via real-time digital simulator (RTDS) for a variety of cases. The obtained results demonstrate that using the proposed PVMT-DPC approach, PV VSI can track the reference power within 0.055 s where the output power has low steady-state oscillations and output current has lower total harmonic distortion (THD) of 1.68%.

Direct Power Control Based on Point of Common Coupling Voltage Modulation for Grid-Tied AC Microgrid PV Inverter

In this paper, a direct power control (DPC) approach is proposed for grid-tied AC MG’s photovoltaic (PV) voltage source inverter (VSI) to regulate directly active and reactive powers by modulating microgrid’s (MG) point of common coupling (PCC) voltage. The proposed PCC voltage modulated (PVM) theory-based DPC method (PVMT-DPC) is composed of nonlinear PVM, nonlinear damping, conventional feedforward and feedback PI controllers. For grid synchronization rather than employing phase-locked-loop (PLL) technology, in this study, direct power calculation of the PCC voltage and current is adopted. Subsequently, at PCC, the computed real and reactive powers are compared with reference powers in order to generate the VSI’s control signals using sinusoidal pulse width modulation (SPWM). Because of the absence of the PLL and DPC method adoption, the suggested controller has a faster convergence rate compared to traditional VSI’s power controllers. Additionally, it displays nearly zero steady-state power oscillations, which assures that MG’s power quality is improved significantly. To validate the proposed PVMT-DPC method’s performance real-time simulations are conducted via real-time digital simulator (RTDS) for a variety of cases. The results demonstrate that PV VSI using the suggested PVMT-DPC approach can track the reference power quicker (0.055 s) along with very low steady-state power oscillations, and lower total harmonic distortion (THD) of 1.697% at VSI output current.

Extended Operation Range of Photovoltaic Inverters by Current Waveform Shaping

The grid connection of photovoltaic voltage source inverters depends on the dc-link voltage level that can be supplied by the maximum power tracking of the photovoltaic system. The inverter disconnects from the grid, if the minimum required dc-link voltage level is violated, which leads to unwanted energy curtailments implying losses to the system owner. This article proposes to apply current waveform shaping to the inverter current in order to reduce the peak value of the voltage waveform at the point of common coupling by which the minimum required dc-link voltage level for power injection is reduced. This extended operation range of photovoltaic inverters is achieved through third harmonic current injection and can be applied to single-phase and three-phase, four-wire inverters without additional converter stages. A control structure for harmonic current injection and harmonic phase determination is presented and validated by simulations and the analysis is verified by experiments.

An AC MPPT with Active/Reactive Power Control Feature for Single-Stage Three-Phase Grid-Connected Photovoltaic VSIs

This article introduces a new AC MPPT (maximum power point tracking) controller for single-stage three-phase grid-connected photovoltaic (PV) voltage source inverters (VSIs) with active/reactive power control capability. Novelty lies in employing the theory of power transfer in short AC transmission lines to achieve MPPT, where two independent control variables exist: load angle and inverter modulation index. Accordingly, the proposed controller maximizes the capabilities of the single-stage VSI and enables it to control either/both active power or/and reactive power, besides achieving MPPT function. Such contribution opens up avenues in MPPTs world in terms of flexibility, fast performance, and low hardware count/cost. AC refers to Alternate Current since the MPPT is managed in AC terms. Theoretical framework of the proposed controller has been addressed. Moreover, the overall system is simulated in MATLAB (The MathWorks, Natick, Massachusetts, USA) environment, and results have been introduced. Design and implementation of proposed algorithms have been carried out using a fixed-point digital signal processor (DSP)TMS320F2812. Furthermore, a breadboard circuit is built up for experimentally investigating the controller's performance using 3-phase VSI that connects PV with the grid. In addition to that, a comprehensive discussion is conducted for demonstrating results. Moreover, a detailed comparison of proposed work with a number of previously published papers in literature is carried out and addressed in this manuscript. Results reveal that introduced controller achieves satisfactory performance.