Photopolymerized Sol-gel Research Articles

Optimization of photo-polymerized sol–gel monolithic stationary phases prepared in polyacrylate-coated fused-silica capillaries for capillary electrochromatography

The preparation of photo-polymerized sol–gel monolithic stationary phases (MSP) within 100μm internal diameter polyacrylate-coated fused-silica capillaries for use in capillary electrochromatography (CEC) was optimized. Eight mixtures containing different amounts of methacryloxypropyltrimethoxysilane (MPTMS) as the polymeric precursor, hydrochloric acid solution as the catalyst, toluene as the porogen and bis(2,4,6-trimethylbenzoyl)-phenylphosphine oxide (Irgacure 819) as the photo-initiator were irradiated at 370nm inside the capillaries in order to complete the MSP polymerization, according to a fractional factorial experimental design 2IV4-1. All the preparation procedure, from capillary pretreatment until the MSP is ready to use in CEC, were made in less than four hours in mild conditions. A high pressurization injection device (HPID) useful for micro-volume syringes was built in order to achieve practical, controlled and precise injections of sols, solvents and electrolytes in the capillaries. The eight MSP were equally washed, conditioned and submitted to CEC procedures via short-end injection, which showed higher efficiency and peak height taking shorter analysis time. Electrochromatographic behaviors of the MSP were corroborated with morphological characterizations by scanning electron microscopy. The optimum condition, which allowed the separation of standard mixture containing thiourea (marker compound), naphthalene, acenaphthene, fluorene, phenanthrene and anthracene in twelve minutes without external pressure assistance, showed efficiencies up to 51,460N/m, relative standard deviation from 0.05 to 3.3% for migration/retention time and from 0.14 to 1.6% for relative area (considering thiourea as an internal standard) and also showed no statistical evidence that three MSP prepared at the same condition are different within 95% confidence interval.

Fast preparation of photopolymerized monolithic columns for capillary electrochromatography

Photopolymerized sol-gel(PSG) columns were prepared using methacryloxypropyltrimethoxysilane as the monomer, toluene as the porogen and hydrochloric acid as the catalyst. Four different photoinitiators such as benzoin methyl ether, Irgacure 819, Irgacure 1700 and Irgacure 1800 were comparatively used in the reaction solution in the presence and absence of sodium dodecyl sulfate. The above eight solutions were respectively irradiated at 365 nm for 5–10 min in each capillary (75 μm inside diameter) to prepare the porous monolithic sol-gel column by a one-step, in situ, process. The chromatographic behavior of the eight PSG columns were comparatively studied, all of which exhibit reversed-phase character. Using these columns, several neutral compounds, namely thiourea, benzene, toluene, ethyl benzene, biphenyl and naphthalene can be separated from mixtures with a largest column efficiency of 74 470 plate/column for thiourea. Addition of sodium dodecyl sulfate in the polymerization process has a significant influence on the morphology and migration time.

External polyacrylate-coating as alternative material for preparation of photopolymerized sol–gel monolithic column

Photopolymerized sol–gel monolithic columns for use in capillary electrochromatography were prepared in 125 μm i.d. polyacrylate-coated fused-silica capillaries. The polyacrylate-coating, unlike the polyimide one, is transparent to the radiation used (≈370 nm), and thus, no coating removal is necessary. This is a very important particularity since intrinsic capillary column characteristics, such as flexibility and mechanical resistance, are unchanged. A mixture containing metacryloxypropyltrimethoxysilane (MPTMS) as the polymeric precursor, hydrochloric acid as the catalyst, toluene as the porogen and bis(2,4,6-trimethylbenzoyl)-phenylphosphine oxide (Irgacure 819) as the photoinitiator was irradiated at 370 nm for 20 min inside the capillaries to prepare the columns through sol–gel approach. The versatility and viability of the use of polyacrilate as a new capillary external coating were shown through preparation of two columns under different conditions, which were tested in electrochromatography for separation of standard mixture containing thiourea (marker compound), propylbenzene, phenanthrene and pyrene.

Visible light‐induced photopolymerization of an in situ macroporous sol–gel monolith

A one-step, in situ, photopolymerization of a mixture of methacryloxypropyltrimethoxysilane in the presence of an acid catalyst, water, and toluene is accomplished in a 75 microm id polyimide-coated capillary using visible light (460 nm) for a 15 min irradiation time. The mixture is a two-component photosystem comprising Irgacure 784 photosensitizer and diphenyliodonium chloride photoinitiator. The visible photopolymerized sol-gel (vis-PSG) column shows RP chromatographic behavior. The analytical potential of these columns is demonstrated with the isocratic separation of small, neutral alkyl phenyl ketones. Operational parameters, such as mobile phase composition, field strength, and column temperature were varied to assess how they affect the separation performance of the monolith.

On-line biological sample cleanup for electrospray mass spectrometry using sol–gel columns

Using a slight overpressure, a urine sample is loaded onto a monolithic photopolymerized sol-gel column that has been derivatized with hydrophobic carbon chains and then the complex urine matrix is washed with aqueous solution. A buffer containing organic solvent is used to elute the adsorbed peptides by an applied voltage and the sample is then introduced into a mass spectrometer by sheath flow electrospray. The importance of desalting this type of sample is demonstrated by an experiment that shows that the signal intensity of a test solution with neurotensin, sprayed directly into the mass spectrometer, decreased from 4.5x10(4) cps to no detectible signal when just 10% urine is added to the sample solution. We suggest that this procedure may find general application for desalting biological samples prior to mass spectrometric analysis.

Enhanced Proteolytic Activity of Covalently Bound Enzymes in Photopolymerized Sol Gel

Trypsin is covalently linked to a photopolymerized sol-gel monolith modified by incorporating poly(ethylene glycol) (PSG-PEG) for on-column digestion of N(alpha)-benzoyl-l-arginine ethyl ester (BAEE) and two peptides, neurotensin and insulin chain B. The coupling of the enzyme to the monolith is via room-temperature Schiff chemistry in which an alkoxysilane reagent (linker) with an aldehyde functional group links to an inactive amine on trypsin to form an imine bond. The proteolytic activity of the immobilized trypsin was measured by monitoring the formation of N alpha-benzoyl-L-arginine (BA), the digestion product of BAEE. The BA is separated from BAEE by capillary electrophoresis and detected downstream (18.5 cm from the microreactor) by absorption (254 nm). Using the Bradford assay, we determined that 97 ng of trypsin is bound to the 1-cm microreactor located at the entrance of capillary column. The bioactivity of the trypsin-PSG-PEG microreactor at 20 degrees C for the digestion of BAEE was found to be 2270 units/mg of immobilized trypsin. The bioactivity of trypsin bound to the capillary wall in the open segment upstream from the monolith was 332 units/mg of immobilized trypsin under the same conditions. In contrast, the activity of free trypsin could not be observed for the digestion of BAEE at 20 degrees C after 16 h of incubation time.

Integration of on-line protein digestion, peptide separation, and protein identification using pepsin-coated photopolymerized sol-gel columns and capillary electrophoresis/mass spectrometry.

A miniaturized pepsin reactor was prepared inside a fused-silica capillary (i.d. 75 microm) by coating a pepsin-containing gel on a photopolymerized porous silica monolith. The pepsin-encapsulated film was prepared by a sol-gel method. The sol-gel reaction was optimized so that the sol solution containing pepsin forms a thin film on the photopolymerized sol-gel (PSG) monolith that was initially fabricated at the inlet of the capillary. Pepsin was encapsulated into the gel matrix without losing its activity. The large surface area of the PSG monolith enabled the immobilized pepsin to achieve a high catalytic turnover rate, and the porous nature of the PSG promotes penetration of large molecular proteins into the column. The immobilized pepsin-digested peptides and proteins, and the resulting mixture of peptide fragments, could be directly separated in the portion of the capillary where no PSG monolith exists. The durability and repeatability of the fabricated pepsin-coated column was tested and found to be satisfactory. An acidic solution consisting of 0.5 M formic acid was used as the running buffer, because it suppresses the adsorption of proteins or peptides on the inner surface of the capillary as well as enables direct connection of the output of the capillary electrophoresis column to a mass spectrometer. The on-line digestion of insulin chain beta and lysozyme provides identification of the proteolytic peptides. Recovery was achieved for 100% of the insulin chain beta amino acid sequence and 73% of the lysozyme amino acid sequence.

Determination of glutamine and serine in rat cerebrospinal fluid using capillary electrochromatography with a modified photopolymerized sol–gel monolithic column

Capillary electrochromatographic separations of amino acid mixtures were studied using two modified porous photopolymerized sol–gel monolithic columns. One was modified with dimethyloctadecylchlorosilane (DMOS), and the other was modified with DMOS, followed by chlorotrimethylsilane to end-cap residual silanol groups. Prior to separation, amino acids were derivatized with 4-fluoro-7-nitro-2,1,3-benzoxadiazole using as a mobile phase 50 m M phosphate (pH 2.5), water, and acetonitrile in the ratio of 1:1:8. Five derivatized amino acids (Asn, Phe, Ala, Ile, and Leu) were separated within 7 min. Theoretical plate numbers varied between 58 700 and 105 000/m. This separation method with the end-capped monolithic column was applied to rat cerebrospinal fluid. The dominant amino acid found was Gln at a concentration of 420 μ M along with small quantities of Ser (54 μ M).

Toward sol-gel electrochromatographic separations on a chip

A porous photopolymerized sol-gel (PSG) monolith was synthesized in the separation channel of a borosilicate glass chip via UV irradiation (5 min) of a mixture of 3-methacryloxypropyltrimethoxysilane, an acid catalyst, a porogen, and a photoinitiator. The PSG monolith adhered strongly to the chemically untreated channel walls. The chip was fabricated using standard lithography procedures to give channels that are 35-μm deep and 90-μm wide. Masking the other channels defined the 4.7-cm PSG section in the separation channel. Two dyes Coumarin 314 and 510 were successfully separated within baseline resolution in 225 s when fluorescent detection occurred immediately after the PSG section. The separation time was reduced to 80 s with little loss in resolution by detecting the dyes 1.2 cm from the front of the PSG monolith.

Effect of preparatory conditions on the performance of photopolymerized sol–gel monoliths for capillary electrochromatography

We prepared different photopolymerized sol–gel (PSG) columns by varying the amount of monomer (methacryloxypropyltrimethoxysilane), porogen (toluene) and catalyst (hydrochloric acid) in the reaction solution containing a photoinitiator (Irgacure 1800). The effects of these variations on the chromatographic behavior of the PSG columns were studied. All of the columns studied exhibited reversed-phase character. The concentration of hydrochloric acid was important for the rigidity of the columns, although it did not affect the separation property. The ratio of monomer solution to porogen was a critical factor in controlling the through-pore size and the surface area of PSG, which were found to significantly affect the separation properties, such as permeability, theoretical plate number, retention time, and separation efficiency, of a mixture of test analytes—thiourea, benzene, and naphthalene. There was no change in the retention order for the test analytes. Short separation times were achieved on PSG columns made from a 10% monomer stock solution and 90% porogen with 1 M hydrochloric acid. Mixtures of polycyclic aromatic hydrocarbons and alkylbenzenes were separated with theoretical plate numbers greater than 100 000 plates/m.

Bonded-phase photopolymerized sol-gel monoliths for reversed phase capillary electrochromatography

A porous chemically modified photopolymerized sol-gel (PSG) monolith enhanced the capillary electrochromatographic separations of two test mixtures, one containing eight alkyl phenyl ketones and the other containing thiourea and three polyaromatic hydrocarbons. Derivatization of the PSG surface with silane coupling reagents resulted in bonded phases of pentafluorophenylpropyldimethyl, pentafluorophenyl, 3,3,3-trifluoropropyl, n-octadimethyl, perfluorohexyl, and aminopropyl. The fabrication of the bonded-phase PSG column is easy to do with the silanization reaction proceeding at room temperature for not longer than 60 minutes. The hydrophobicity of the PSG was altered without degrading its chromatographic performance. The bonded-phase PSG monoliths have higher stability at pH values below 4 as compared to the parent (underivatized) PSG. Separations of different mixtures containing nucleosides, positively charged peptides, and taxol derivatives illustrate the potential of bonded-phase PSG columns for the analyses of biologically and pharmaceutically important compounds. We report column efficiencies of up to 180 000 plates/meter and retention factors as large as 28.6 for decanophenone.

Strategy for on-line preconcentration in chromatographic separations.

In chromatographic separations, the heights of peaks are proportional to the concentrations of sample components present in an injected mixture. In general, an increase in the peak height cannot be achieved by simply increasing the injection time or the sample plug length. An exception occurs if some form of on-line preconcentration is possible. We present a new strategy for achieving on-line preconcentration by the use of a porous chromatographic material that acts as a solid-phase extractor as well as a stationary-phase separator. We are able to realize significant on-line preconcentration using capillary columns filled with a photopolymerized sol-gel (PSG). More than 2-cm plugs of sample solution can be loaded into the capillary and concentrated using a running buffer that is the same as the injection buffer (to avoid solvent gradient effects). As a demonstration, mixtures of three different polycyclic aromatic hydrocarbons, eight different alkyl phenyl ketones, and five different peptides in solutions of aqueous acetonitrile have been injected onto the PSG column and separated by capillary electrochromatography. The preconcentration is marked in terms of peak heights, with up to 100-fold increase for the PAH mixture, 30-fold for the alkyl phenyl ketone mixture, and 20-fold for the peptide mixture. Preconcentration takes place because of the high mass-transfer rates possible in the highly porous structure, and the extent of preconcentration follows the retention factor k for a given analyte.

On-Line Preconcentration in Capillary Electrochromatography Using a Porous Monolith Together with Solvent Gradient and Sample Stacking

Preconcentration effects of solvent gradient and sample stacking are investigated on a photopolymerized sol-gel (PSG) in capillary electrochromatography. The porous PSG monolith has a high mass-transfer rate. This characteristic promotes preconcentration of dilute samples. Plugs of samples more than 2 cm in length prepared in the separation solution (nongradient condition) are injected onto the PSG column. The extent of preconcentration is quite significant, showing up to a 100-fold increase in peak heights of the separated analytes. Even larger preconcentrations are achieved under gradient conditions by dissolving the sample in a matrix with a higher concentration of noneluting solvent (water). For eight alkyl phenyl ketones and four polycyclic aromatic hydrocarbons that serve as neutral test analytes, improvements in peak heights obtained under gradient conditions can be more than a 1000-fold. Indeed, injection of a 91.2-cm plug, which is more than 3 times the total length of the capillary, was possible with only a minor loss in resolution. Five peptides serve as charged test analytes. Nongradient conditions in which the sample is hydrodynamically injected onto the PSG column show sizable preconcentration because of sample stacking. The use of a solvent gradient with the same ionic strength, however, does not appear to have practical value because of destacking caused by the changing organic composition that affects the conductivity. As an alternative preconcentration method, we demonstrate that electric field-enhanced sample injection on the PSG yielded up to a 1000-fold improvement in detection sensitivity for the test peptides.

Photopolymerized sol-gel monoliths for capillary electrochromatography.

A solution of methacryloxypropyltrimethoxysilane in the presence of an acid catalyst, water, toluene, and a photoinitiator was irradiated at 365 nm for 5 min in a 75-microm i.d. capillary to prepare a porous monolithic sol-gel column by a one-step, in situ, process. The photopolymerized sol-gel (PSG) column shows reversed-phase behavior. Using this column, a variety of low-molecular-weight neutral compounds, including polycyclic aromatic hydrocarbons, alkyl benzenes, alkyl phenyl ketones, and steroids are separated from mixtures. Various different operational parameters, such as buffer composition, field strength, and column temperature, were varied to assess their influence on column performance. Use of PSG as a stationary phase for a pressure-driven separation is also demonstrated.

Photopolymerized sol–gel frits for packed columns in capillary electrochromatography

Porous sol–gel frits are fabricated in a capillary column by filling it with a solution of 3-(trimethoxysilyl)propyl methacrylate, hydrochloric acid, water, toluene (porogen), and a photoinitiator (Irgacure 1800) and exposing it to UV light at 365 nm for 5 min. The separation column (30 cm×75 μm I.D.) contains between the inlet and outlet frits a 15-cm packed segment filled with 5-μm silica particles modified with the chiral compound ( S)- N-3,5-dinitrobenzoyl-1-naphthylglycine. A detection window (1 mm long) is placed immediately after the outlet frit. To demonstrate the performance of this chiral separation column, mixtures of 16 different amino acids (three of which are not naturally occurring) derivatized with the fluorogenic reagent 4-fluoro-7-nitro-2,1,3-benzoxadiazole were separated by capillary chromatography. The enantiomeric separation of the column results in a resolution ranging from 1.21 to 8.29, and a plate height ranging from 8.7 to 39 μm.