Photoluminescence Quantum Yield Research Articles

Bandgap-universal passivation enables stable perovskite solar cells with low photovoltage loss.

The efficiency and longevity of metal-halide perovskite solar cells are typically dictated by nonradiative defect-mediated charge recombination. In this work, we demonstrate a vapor-based amino-silane passivation that reduces photovoltage deficits to around 100 millivolts (>90% of the thermodynamic limit) in perovskite solar cells of bandgaps between 1.6 and 1.8 electron volts, which is crucial for tandem applications. A primary-, secondary-, or tertiary-amino-silane alone negatively or barely affected perovskite crystallinity and charge transport, but amino-silanes that incorporate primary and secondary amines yield up to a 60-fold increase in photoluminescence quantum yield and preserve long-range conduction. Amino-silane-treated devices retained 95% power conversion efficiency for more than 1500 hours under full-spectrum sunlight at 85°C and open-circuit conditions in ambient air with a relative humidity of 50 to 60%.

Facile Synthesis and Photoluminescent Properties of Asymmetric Perylene Diimides Capable of Tuning Emission Colors in Polymeric Matrices.

We report the facile synthesis of asymmetric perylene diimides (asym-PDIs) using readily available reagents, demonstrating their distinct photoluminescent properties. In CHCl3, asym-PDIs exhibit higher solubility compared to traditional perylene dyes, of which solubilities can be varied by substituent selections. Among them, UV-vis absorption spectra of CPE in CHCl3 solution displayed no aggregate peaks in the ground state, maintaining high photoluminescent quantum yields. Also, CPE can be readily dispersed into poly(methyl methacrylate) PMMA (CPE-PMMA), forming thin films without aggregate formation. Importantly, the emission color of CPE-PMMA thin films significantly changes with the addition of polycyclic aromatic hydrocarbons (PAHs). These color changes should be strongly correlated with the HOMO level of the added PAHs.

A Conjugated Carboranyl Main Chain Polymer with Aggregation-Induced Emission in the Near-Infrared.

Materials exhibiting aggregation-induced emission (AIE) are both highly emissive in the solid state and prompt a strongly red-shifted emission and should therefore pose as good candidates toward emerging near-infrared (NIR) applications of organic semiconductors (OSCs). Despite this, very few AIE materials have been reported with significant emissivity past 700 nm. In this work, we elucidate the potential of ortho-carborane as an AIE-active component in the design of NIR-emitting OSCs. By incorporating ortho-carborane in the backbone of a conjugated polymer, a remarkable solid-state photoluminescence quantum yield of 13.4% is achieved, with a photoluminescence maximum of 734 nm. In contrast, the corresponding para and meta isomers exhibited aggregation-caused quenching. The materials are demonstrated for electronic applications through the fabrication of nondoped polymer light-emitting diodes. Devices employing the ortho isomer achieved nearly pure NIR emission, with 86% of emission at wavelengths longer than 700 nm and an electroluminescence maximum at 761 nm, producing a significant light output of 1.37 W sr-1 m-2.

Fluorescence‐Enabled Colored Bilayer Subambient Radiative Cooling Coatings

AbstractPassive daytime radiative cooling has emerged as a promising green technology for the thermal management of buildings, vehicles, textiles, and electronics. Typically, both high solar reflectance and high thermal emissivity are prerequisites to achieve sufficient daytime cooling. However, colored radiative cooling materials are facing the dilemma of introducing visible light absorption, leading to challenges in balancing cooling and aesthetic demands. Here, three colored bilayer radiative cooling coatings, each comprised of a white base layer and a colored top layer with fluorescence enhancement are fabricated. Three phosphors (Sr2Si5N8:Eu2+, Y3Al5O12:Ce3+, and (Ba,Sr)SiO4:Eu2+) are employed with respective photoluminescence quantum yields (PLQYs) of 81%, 95.8%, and 91.0% as the colored pigment in the top layer. To mitigate the contradiction between coloration and solar reflectance, SiO2 microspheres are introduced into the top layer and utilize their Mie‐resonance‐based multiple scattering to increase the photoluminescent (PL) properties of the phosphors, which jointly boosts the effective solar reflectance (ESR) of the top layer. As a result, the three bilayer coatings exhibit soft colors while achieving subambient cooling with temperature drops of up to 1.5 °C. This fluorescence‐enhancement strategy may pave the way for preparing highly efficient radiative cooling coatings with tunable colors.

Efficient Large-Area (81 cm2) Ternary Copper Halides Light-Emitting Diodes with External Quantum Efficiency Exceeding 13% via Host-Guest Strategy.

Ternary copper (Cu) halides are promising candidates for replacing toxic lead halides in the field of perovskite light-emitting diodes (LEDs) toward practical applications. However, the electroluminescent performance of Cu halide-based LEDs remains a great challenge due to the presence of serious nonradiative recombination and inefficient charge transport in Cu halide emitters. Here, the rational design of host-guest [dppb]2Cu2I2 (dppb denotes 1,2-bis[diphenylphosphino]benzene) emitters and its utility in fabricating efficient Cu halide-based green LEDs that show a high external quantum efficiency (EQE) of 13.39% are reported. The host-guest [dppb]2Cu2I2 emitters with mCP (1,3-bis(N-carbazolyl)benzene) host demonstrate a significant improvement of carrier radiative recombination efficiency, with the photoluminescence quantum yield increased by nearly ten times, which is rooted in the efficient energy transfer and type-I energy level alignment between [dppb]2Cu2I2 and mCP. Moreover, the charge-transporting mCP host can raise the carrier mobility of [dppb]2Cu2I2 films, thereby enhancing the charge transport and recombination. More importantly, this strategy enables a large-area prototype LED with a record-breaking area up to 81 cm2, along with a decent EQE of 10.02% and uniform luminance. It is believed these results represent an encouraging stepping stone to bring Cu halide-based LEDs from the laboratory toward commercial lighting and display panels.

Achieving Near-Unity Red Light Photoluminescence in Antimony Halide Crystals via Polyhedron Regulation.

Exploration of efficient red emitting antimony hybrid halide with large Stokes shift and zero self-absorption is highly desirable due to its enormous potential for applications in solid light emitting, and active optical waveguides. However, it is still challenging and rarely reported. Herein, a series of (TMS)2SbCl5 (TMS=triphenylsulfonium cation) crystals have been prepared with diverse [SbCl5]2- configurations and distinctive emission color. Among them, cubic-phase (TMS)2SbCl5 shows bright red emission with a large Stokes shift of 312 nm. In contrast, monoclinic and orthorhombic (TMS)2SbCl5 crystals deliver efficient yellow and orange emission, respectively. Comprehensive structural investigations reveal that larger Stokes shift and longer-wavelength emission of cubic (TMS)2SbCl5 can be attributed to the larger lattice volume and longer Sb⋅⋅⋅Sb distance, which favor sufficient structural aberration freedom at excited states. Together with robust stability, (TMS)2SbCl5 crystal family has been applied as optical waveguide with ultralow loss coefficient of 3.67 ⋅ 10-4 dB μm-1, and shows superior performance in white-light emission and anti-counterfeiting. In short, our study provides a novel and fundamental perspective to structure-property-application relationship of antimony hybrid halides, which will contribute to future rational design of high-performance emissive metal halides.

Achieving Near‐Unity Red Light Photoluminescence in Antimony Halide Crystals via Polyhedron Regulation

AbstractExploration of efficient red emitting antimony hybrid halide with large Stokes shift and zero self‐absorption is highly desirable due to its enormous potential for applications in solid light emitting, and active optical waveguides. However, it is still challenging and rarely reported. Herein, a series of (TMS)2SbCl5 (TMS=triphenylsulfonium cation) crystals have been prepared with diverse [SbCl5]2− configurations and distinctive emission color. Among them, cubic‐phase (TMS)2SbCl5 shows bright red emission with a large Stokes shift of 312 nm. In contrast, monoclinic and orthorhombic (TMS)2SbCl5 crystals deliver efficient yellow and orange emission, respectively. Comprehensive structural investigations reveal that larger Stokes shift and longer‐wavelength emission of cubic (TMS)2SbCl5 can be attributed to the larger lattice volume and longer Sb⋅⋅⋅Sb distance, which favor sufficient structural aberration freedom at excited states. Together with robust stability, (TMS)2SbCl5 crystal family has been applied as optical waveguide with ultralow loss coefficient of 3.67 ⋅ 10−4 dB μm−1, and shows superior performance in white‐light emission and anti‐counterfeiting. In short, our study provides a novel and fundamental perspective to structure‐property‐application relationship of antimony hybrid halides, which will contribute to future rational design of high‐performance emissive metal halides.

Efficient Green Spin Light-Emitting Diodes Enabled by Ultrafast Energy- and Spin-Funneling in Chiral Perovskites.

Introducing molecular chirality into perovskite crystal structures has enabled the control of carrier spin states, giving rise to circularly polarized luminescence (CPL) in thin films and circularly polarized electroluminescence (CPEL) in LEDs. Spin-LEDs can be fabricated either through a spin-filtering layer enabled by chiral-induced spin selectivity or a chiral emissive layer. The former requires a high degree of spin polarization and a compatible spinterface for efficient spin injection, which might not be easily integrated into LEDs. Alternatively, a chiral emissive layer can also generate circularly polarized electroluminescence, but the efficiency remains low and the fundamental mechanism is elusive. In this work, we report an efficient green LED based on quasi-two-dimensional (quasi-2D) chiral perovskites as the emitting layer (EML), where CPEL is directly produced without separate carrier spin injection. The optimized chiral perovskite thin films exhibited strong CPL at 535 nm with a photoluminescence quantum yield (PLQY) of 91% and a photoluminescence dissymmetry factor (glum) of 8.6 × 10-2. Efficient green spin-LEDs were successfully demonstrated, with a large EL dissymmetry factor (gEL) of 7.8 × 10-2 and a maximum external quantum efficiency (EQE) of 13.5% at room temperature. Ultrafast transient absorption (TA) spectroscopic study shows that the CPEL is generated from a rapid energy transfer accompanied by spin transfer from 2D to 3D perovskites. Our study not only demonstrates a reliable approach to achieve high performance spin-LEDs but also reveals the fundamental mechanism of CPEL with an emissive layer of chiral perovskites.

Ultrasensitive Piezochromic Molecular Crystals: Mechanical Pressure‐Induced Controlled Regulation of TADF and RTP

AbstractConsidering that regulation of thermally activated delayed fluorescence (TADF) and room temperature phosphorescence (RTP) is necessary for a fluorophore to survive and properly show its characteristic features, it is successfully shown herein that a carefully designed novel pyrene derivative can exhibit remarkable aggregation‐induced emission (AIE) overcoming the characteristic fast excitonic decay of pyrene compounds. Moreover, it is established that J‐aggregation in the red‐emitting molecular crystals of the compound reduces the singlet‐triplet energy gap (∆EST), allowing TADF with a very high photoluminescence quantum yield (PLQY) of 72%. Whereas, anisotropic grinding of the same crystals generates well‐defined microcrystals that show RTP as the nature of aggregation changes. Impressively, under isotropic hydrostatic pressure, the crystals show near‐infra‐red (NIR) emission with a very high piezochromic luminescence sensitivity of 46.2 nm GPa−1. The results have established that formation of stable H‐aggregates in the microcrystals is responsible for the ultra‐long RTP. A highly sophisticated full‐spectrum Mueller‐matrix analysis is used for the first time in such systems to demonstrate the details of the effect of perturbation (pressure) on molecular conformation.

Targeted synthesis of a 3D covalent organic framework with fjh topology exhibiting high photoluminescence: A robust platform for sensitive detection of furantoin

The inappropriate use of antibiotics poses significant risks to both the environment and human health, necessitating the development of accurate and sensitive detection methods. Fluorescence detection, particularly utilizing three-dimensional (3D) covalent organic frameworks (COFs), stands out as a promising avenue. Unlike two-dimensional COFs, 3D COFs can mitigate fluorescence quenching resulting from non-radiative energy loss, primarily attributed to π-π interlayer stacking. In this study, by carefully selecting and designing the building blocks, we synthesized a 3D COF named PyTTA-TTFB-COF with fjh topology and remarkable photoluminescence. This was achieved through the combination of a 4-connected square chromophore, 1,3,6,8-Tetrakis(4-aminophenyl) pyrene, with a 3-connected triangle, 1,3,5-trimethyl-2,4,6-tris(4-formylphenyl) benzene, possessing a specific stereo conformation. Significantly, PyTTA-TTFB-COF exhibits a high photoluminescence quantum yield, notably reaching 60.1% in acetonitrile. Moreover, it displays substantial fluorescence quenching when exposed to furantoin, surpassing the performance observed with other antibiotics. Competitive experiments have confirmed that PyTTA-TTFB-COF can serve as a specific fluorescent probe for the interference-free detection of furantoin.

Green‐Emissive Carbon Dots with a High Quantum Yield Applied for Photoconversion Film to Prevent from Blue Light Damage

AbstractHigh‐energy blue light is highly detrimental to health as it can penetrate the lens into the retina, potentially causing atrophy or even death of retinal pigment epithelial cells. To prevent the harmful effects of high‐energy blue light on our health, here the preparation of a photoconversion film specifically designed to block high‐energy blue light is reported, which is composed of green‐emissive carbon dots (G‐CDs) with a high photoluminescence quantum yield (PLQY = 95%) dispersed in polyvinyl alcohol (PVA) matrix. Notably, such a film (named as G‐CDs@PVA) not only converts an incident laser light with a short wavelength into a fluorescence with a longer wavelength, but also exhibits concentration‐dependent (0, 10, 20, and 30 wt.%) blue light barrier rate and green‐emissive intensity. With the increase of the concentration of G‐CDs in the film, the blue light barrier rate of the film as well as the maximum intensity of the green emission are also increased. When the concentration of G‐CDs reaches 30 wt.%, the blue light barrier rate of G‐CDs@PVA achieves up to 97%. Furthermore, G‐CDs@PVA film is attached to a blue light‐emitting diode (LED) chip to explore its practical application in the field of blocking blue light damage.

Boosting External Quantum Efficiency to 12.0% of an Ultraviolet OLED by Engineering the Horizontal Dipole Orientation of a Hot Exciton Emitter

Currently, much research effort has been devoted to improving the exciton utilization efficiency and narrowing the emission spectra of ultraviolet (UV) fluorophores for organic light‐emitting diode (OLED) applications, while almost no attention has been paid to optimizing their light out‐coupling efficiency. Here, we developed a linear donor‐acceptor‐donor (D‐A‐D) triad, namely CDFDB, which possesses high‐lying reverse intersystem crossing (hRISC) property. Thanks to its integrated narrowband UV photoluminescence (PL) (λPL: 397 nm; FWHM: 48 nm), moderate PL quantum yield (φPL: 72%, Tol), good triplet hot exciton (HE) conversion capability, and large horizontal dipole ratio (Θ//: 92%), the OLEDs based on CDFDB not only can emit UV electroluminescence with relatively good color purity (λEL: 398 nm; CIEx,y: 0.161, 0.040), but also show a record maximum external quantum efficiency (EQEmax) of 12.0%. This study highlights the important role of horizontal dipole orientation engineering in the molecular design of HE UV‐OLED fluorophores.

Boosting External Quantum Efficiency to 12.0% of an Ultraviolet OLED by Engineering the Horizontal Dipole Orientation of a Hot Exciton Emitter.

Currently, much research effort has been devoted to improving the exciton utilization efficiency and narrowing the emission spectra of ultraviolet (UV) fluorophores for organic light-emitting diode (OLED) applications, while almost no attention has been paid to optimizing their light out-coupling efficiency. Here, we developed a linear donor-acceptor-donor (D-A-D) triad, namely CDFDB, which possesses high-lying reverse intersystem crossing (hRISC) property. Thanks to its integrated narrowband UV photoluminescence (PL) (λPL: 397 nm; FWHM: 48 nm), moderate PL quantum yield (φPL: 72%, Tol), good triplet hot exciton (HE) conversion capability, and large horizontal dipole ratio (Θ//: 92%), the OLEDs based on CDFDB not only can emit UV electroluminescence with relatively good color purity (λEL: 398 nm; CIEx,y: 0.161, 0.040), but also show a record maximum external quantum efficiency (EQEmax) of 12.0%. This study highlights the important role of horizontal dipole orientation engineering in the molecular design of HE UV-OLED fluorophores.

Modulating the Locally Excited States with a Regulating Substituent for Highly Efficient Red/Near‐Infrared Thermally Activated Delayed Fluorescence Emitters

AbstractDeveloping highly efficient red/near‐infrared (NIR) thermally activated delayed fluorescence (TADF) materials is important for organic light‐emitting diodes (OLEDs). Here, two TADF emitters, APTT and APTI, which have the same D/A backbone but different attaching groups at acenaphtho‐[1,2‐b]pyrazine‐8,9‐dicarbonitrile (APDC) core, are reported. The appended regulating groups can not only suppress the D/A rotation due to the space confinement effects but also modulate the locally excited triplet state (3LE). The improved molecular rigidity suppresses the non‐radiative process, accounting for the improved photoluminescence quantum yields (PLQYs), while the modulated 3LE promotes the reverse intersystem crossing (RISC) process due to the high utilization efficiency of triplets. Consequently, both APTT and APTI demonstrate high PLQY and fast RISC process, thereby enhancing TADF efficiency. The doped devices based on APTT and APTI achieve maximum external quantum efficiency (EQEmax) values of 20.5% and 25.4% with emission peaks at 664 and 670 nm, respectively. The non‐doped devices of APTT and APTI achieve the EQEmax of 2.8% and 2.9% with emission peaks at 788 and 794 nm, respectively. Encouragingly, the non‐doped devices of APTI have set new records for near‐infrared TADF OLEDs based on the APDC core. This study provides an efficient approach to modulating the optoelectronic properties of highly efficient NIR TADF OLEDs.

Pressure-Induced Distinct Self-Trapped Exciton Emission in Sb3+-Doped Cs2NaInCl6 Double Perovskite

Abstract The Cs2NaInCl6 double perovskite is one of the most promising lead-free perovskites due to its exceptional stability and straightforward synthesis. However, it faces challenges related to inefficient photoluminescence. Doping and high-pressure are employed to tailor the optical properties of Cs2NaInCl6. Herein, Sb3+ doped Cs2NaInCl6 (Sb3+:Cs2NaInCl6) was synthesized and exhibits blue emission with a photoluminescence quantum yield of up to 37.3%. Further, by employing pressure tuning, a blue stable emission under a very wide range from 2.7 GPa to 9.8 GPa, for the first time, realized in Sb3+:Cs2NaInCl6. Subsequently, the emission intensity of Sb3+:Cs2NaInCl6 experiences a significant increase (3.3-times) at 19.0 GPa. We reveal that the pressure-induce the distinct emissions can be attributed to the carrier self-trapping and detrapping between Cs2NaInCl6 and Sb3+. Notably, the lattice compression in the cubic phase inevitably modify the band gap of Sb3+:Cs2NaInCl6. Our findings provide valuable insights into the effects of the high pressure in further boosting unique emission characteristics but also offer promising opportunities for the development of doped double perovskites with enhanced optical functionalities.

Metal Fluorides Passivate II-VI and III-V Quantum Dots.

Quantum dots (QDs) with metal fluoride surface ligands were prepared via reaction with anhydrous oleylammonium fluoride. Carboxylate terminated II-VI QDs underwent carboxylate for fluoride exchange, while InP QDs underwent photochemical acidolysis yielding oleylamine, PH3, and InF3. The final photoluminescence quantum yield (PLQY) reached 83% for InP and near unity for core-shell QDs. Core-only CdS QDs showed dramatic improvements in PLQY, but only after exposure to air. Following etching, the InP QDs were bound by oleylamine ligands that were characterized by the frequency and breadth of the corresponding ν(N-H) bands in the infrared absorption spectrum. The fluoride content (1.6-9.2 nm-2) was measured by titration with chlorotrimethylsilane and compared with the oleylamine content (2.3-5.1 nm-2) supporting the formation of densely covered surfaces. The influence of metal fluoride adsorption on the air stability of QDs is discussed.

Circularly Polarized Luminescence Induced by Hydrogen‐Bonding Networks in a One‐Dimensional Hybrid Manganese(II) Chloride

AbstractChiral hybrid metal halides hold great potential as circularly polarized luminescence light sources. Herein, we have obtained two enantiomeric pairs of one‐dimensional hybrid chiral manganese(II) chloride single crystals, R/S‐(3‐methyl piperidine)MnCl3 (R/S‐1) and R/S‐(3‐hydroxy piperidine)MnCl3 (R/S‐2), crystallizing in the non‐centrosymmetric space group P212121. In comparison to R/S‐1, R/S‐2 single crystals not only show red emission with near‐unity photoluminescence quantum yield (PLQY) and high resistance to thermal quenching but also exhibit circularly polarized luminescence with an asymmetry factor (glum) of 2.5×10−3, which can be attributed to the enhanced crystal rigidity resulting from the hydrogen bonding networks between R/S‐(3‐hydroxy piperidine) cations and [MnCl6]4− chains. The circularly polarized luminescence activities originate from the asymmetric [MnCl6]4− luminophores induced by N−H⋅⋅⋅Cl hydrogen bonding with R/S‐(3‐hydroxy piperidine). Moreover, these samples demonstrate great application potential in circularly polarized light‐emitting diodes and X‐ray scintillators. This work shows a highly efficient photoluminescent Mn‐based halide and offers a strategy for designing multifunctional chiral metal halides.

Synthesis, characterization, and optical studies of lead-free perovskite, Cs3M2Br9 (M = Bi, Sb) nanocrystals

In recent years, there has been a surge in research interest surrounding all inorganic lead perovskite nanocrystals (NCs) owing to their exceptional performance in various optoelectronic devices. Nevertheless, the presence of lead and concerns regarding its toxicity and stability have cast a shadow over their potential wide-ranging applications. In this study, we present the synthesis of two lead-free all-inorganic perovskite materials, Cs3M2Br9 (where M = Bi or Sb), in bulk form, using an aqueous halide acid medium. Additionally, we describe a top-down approach for the fabrication of two lead-free all-inorganic perovskite, Cs3M2Br9 (M = Bi or Sb) NCs. The Cs3Sb2Br9 NCs display a sheet-like morphology, while Cs3Bi2Br9 NCs exhibit a cubic structure. The PL spectra of Cs3Sb2Br9 and Cs3Bi2Br9 NCs exhibit distinct emission peaks at 476 nm and 472 nm, respectively, with relatively narrow full width at half maximum (FWHM) of 44 nm and 38 nm, respectively. Cs3Sb2Br9 and Cs3Bi2Br9 NCs demonstrate excellent thermal stability up to 320 °C and 470 °C, respectively. Notably, the high photoluminescence quantum yield (PLQY) of these NCs, Cs3Sb2Br9 NCs (31 %) and Cs3Bi2Br9 NCs (36 %) are highly beneficial for optoelectronic applications is observed.

Circularly Polarized Luminescence Induced by Hydrogen-Bonding Networks in a One-Dimensional Hybrid Manganese(II) Chloride.

Chiral hybrid metal halides hold great potential as circularly polarized luminescence light sources. Herein, we have obtained two enantiomeric pairs of one-dimensional hybrid chiral manganese(II) chloride single crystals, R/S-(3-methyl piperidine)MnCl3 (R/S-1) and R/S-(3-hydroxy piperidine)MnCl3 (R/S-2), crystallizing in the non-centrosymmetric space group P212121. In comparison to R/S-1, R/S-2 single crystals not only show red emission with near-unity photoluminescence quantum yield (PLQY) and high resistance to thermal quenching but also exhibit circularly polarized luminescence with an asymmetry factor (glum) of 2.5×10-3, which can be attributed to the enhanced crystal rigidity resulting from the hydrogen bonding networks between R/S-(3-hydroxy piperidine) cations and [MnCl6]4- chains. The circularly polarized luminescence activities originate from the asymmetric [MnCl6]4- luminophores induced by N-H⋅⋅⋅Cl hydrogen bonding with R/S-(3-hydroxy piperidine). Moreover, these samples demonstrate great application potential in circularly polarized light-emitting diodes and X-ray scintillators. This work shows a highly efficient photoluminescent Mn-based halide and offers a strategy for designing multifunctional chiral metal halides.

From Dopant to Host: Solution Synthesis and Light‐Emitting Applications of Organic‐Inorganic Lanthanide‐Based Metal Halides

The rich and unique energy level structure arising from 4fn inner shell configuration of trivalent lanthanide ions (Ln3+) renders them highly attractive for light‐emitting applications. Currently, research primarily focuses on Ln3+ doping in either traditional garnets or the recently developed perovskite phosphors. However, there have been few reports on stable phosphors crystallized with pure lanthanide elements. Herein, a universal solution‐based route to eight Ln3+‐based metal halides from the organic‐inorganic A4LnX7 family is described, where A+ = 4,4‐difluoropiperidinium (DFPD+), Ln3+ = Nd3+, Eu3+, Ho3+, Sm3+, Tm3+, Tb3+, Yb3+, Er3+, and X− = Cl−, Br−. Visible photoluminescence (PL) is observed from Tb3+‐, Eu3+‐, Ho3+‐, and Sm3+‐based compounds with Tb and Eu compositions exhibiting high PL quantum yields of 90–100%; Nd3+‐, Tm3+‐, Yb3+‐, and Er3+‐based crystals show fascinating near‐infrared emission. Light‐emitting diodes (LEDs) fabricated with (DFPD)4TbCl7 yield characteristic emission of Tb3+, representing the first demonstration of electroluminescence from these organic‐inorganic Ln3+‐based metal halides. Moreover, these materials exhibit distinct excitation wavelength‐dependent emission after alloying with different Ln3+ ions, making them interesting for multicolor display and multilevel information encryption applications. It is foreseen that this study will open up the way to a possible design of robust optoelectronic devices based on lanthanide metal halides.