Photocatalytic Hydrogen Evolution Research Articles

Construction of 3D MoSx/Zn2In2S5 nanoflower heterojunction for boosted photothermal-assisted photocatalytic hydrogen evolution in biomass solution

Hydrogen production from solar energy conversion method is an attractive strategy to alleviate the energy crisis. The use of non-noble metal cocatalysts instead of noble metal monomers to improve the performance of photocatalytic hydrogen evolution reactions has been pursued by researchers. In this work, we develop a single-photon excited electron transport pathway system for photocatalytic hydrogen production performance studies by coupling 0D MoSx nanodots and 3D Zn2In2S5 nanoflowers. Experimental results combined with DFT calculations show that MoSx not only imparts photothermal properties to the composite material, but also acts as a conduit for electron transport, which can accelerate the rapid separation and transfer of photocatalytic charges. Among them, 3-MoSx/Zn2In2S5 selectively promoted photocatalyzed conversion of benzyl alcohol (BA, 100% conversion) into benzaldehyde (BAD, 96.82% selectivity) by simultaneous co-production of hydrogen (8.74 mmol•g−1•h−1) within 1 h, which is about 7.80 and 2.69 times higher than pure Zn2In2S5, respectively. Further, 3-MoSx/Zn2In2S5 can realize the hydrogen production reaction with glycerol as the substrate with a remarkable effect (up to 5.47 mmol•g−1•h−1). Additionally, 3-MoSx/Zn2In2S5 also showed some hydrogen production performance when other biomasses (glucose, xylose, and cellulose) were used as substrates. This work provides a feasible strategy for the design of photothermal photocatalysts for synergistic hydrogen production from biomass.

An intermediary route to CdS/Bi2S3 architectures with high-activity and stability in photocatalytic water splitting and dye degradation

The binary CdS/Bi2S3 heterostructures were fabricated by employing ZnO/Bi2S3 as active intermediates for the first time, which consisted of 0D CdS nanoparticles with sizes of 10–20 nm decorated on 3D Bi2S3 mircoflowers assembled by 1D nanorods. The whole formation mechanism of CdS/Bi2S3 heterostructure was systematically investigated. Specifically, the optimal CdS/Bi2S3 sample (CB-3) achieved the highest photocatalytic hydrogen evolution reaction rate of 3.85 mmol·g−1·h−1, about 16.74 and 25.67 times greater than that of single Bi2S3 and CdS. Besides, the apparent reaction rate constant of CB-3 for photodegradation of Congo red reached up to 0.0412 min−1, being 41.2 and 4.08 folds higher than that of solo Bi2S3 and CdS. The recycled tests over CB-3 were ready to take on the superb photostability. Furthermore, the S-scheme mechanism of photoinduced charges was rationally proposed. This work provides a new insight for the construction of composite photocatalysts for boosted solar-light-driven photocatalytic performance.

Changeable Active Sites by Pr Doping CuSA-TiO2 Photocatalyst for Excellent Hydrogen Production.

Photocatalytic water splitting for clean hydrogen production has been a very attractive research field for decades. However, the insightful understanding of the actual active sites and their impact on catalytic performance is still ambiguous. Herein, a Pr-doped TiO2-supported Cu single atom (SA) photocatalyst is successfully synthesized (noted as Cu/Pr-TiO2). It is found that Pr dopants passivate the formation of oxygen vacancies, promoting the density of photogenerated electrons on the CuSAs, and optimizing the electronic structure and H* adsorption behavior on the CuSA active sites. The photocatalytic hydrogen evolution rate of the obtained Cu/Pr-TiO2 catalyst reaches 32.88mmolg-1h-1, 2.3 times higher than the Cu/TiO2. Innovatively, the excellent catalytic activity and performance is attributed to the active sites change from O atoms to CuSAs after Pr doping is found. This work provides new insight for understanding the accurate roles of single atoms in photocatalytic water splitting.

Full-Space Electric Field in Mo-Decorated Zn2In2S5 Polarization Photocatalyst for Oriented Charge Flow and Efficient Hydrogen Production.

Integration of photocatalytic hydrogen (H2) evolution with oxidative organic synthesis presents a highly attractive strategy for the simultaneous production of clean H2 fuel and high-value chemicals. However, the sluggish dynamics of photogenerated charge carriers across the photocatalysts result in low photoconversion efficiency, hindering the wide applications of such a technology. Herein, we overcome this limitation by inducing the full-space electric field via charge polarization engineering on a Mo cluster-decorated Zn2In2S5 (Mo-Zn2In2S5) photocatalyst. Specifically, this full-space electric field arises from a cascade of the bulk electric field (BEF) and local surface electric field (LSEF), triggering the oriented migration of photogenerated electrons from [Zn-S] regions to [In-S] regions and eventually to Mo cluster sites, ensuring efficient separation of bulk and surface charge carriers. Moreover, the surface Mo clusters induce a tip enhancement effect to optimize charge transfer behavior by augmenting electrons and proton concentration around the active sites on the basal plane of Zn2In2S5. Notably, the optimized Mo1.5-Zn2In2S5 catalyst achieves exceptional H2 and benzaldehyde production rates of 34.35 and 45.31mmol gcat -1 h-1, respectively, outperforming pristine ZnIn2S4 by 3.83- and 4.15-fold. Our findings mark a significant stride in steering charge flow for enhanced photocatalytic performance. This article is protected by copyright. All rights reserved.

Π‐Bridge Modulations in D–π–A Conjugated Microporous Polymers to Facilitate Charge Separation and Transfer Kinetics for Efficient Photocatalysis

AbstractThe burgeoning field of conjugated microporous polymers (CMPs) has generated widespread interest due to their potential as photocatalysts for hydrogen production from water. Nevertheless, their photocatalytic performance is sometimes hindered by inadequate charge separation and transfer, coupled with rapid charge recombination. Herein, a strategy to enhance photocatalytic performance via the customization of π‐bridges through the modulation of heteroatoms in a series of donor‐π‐acceptor (D‐π‐A) CMPs is proposed. This affords optimized energy levels and improved charge separation and transfer, thus boosting photocatalytic efficiency. Among various heteroatom substitutions, S‐doped CMP (10 mg) demonstrates the highest photocatalytic hydrogen evolution rate of 203 µmol h−1 (AQY450nm = 7.4%) under visible light irradiation. Subsequent experimental analysis reveals its superior photocatalytic performance can be largely related to its minimized exciton binding energy, facilitated charge transfer efficiency, and impeded charge recombination among these heteroatom‐doped D‐π‐A CMPs. This research paves the way for the rational design and modification of organic semiconductors for advanced solar‐driven photocatalysis by promoting charge separation and transfer.

Linkage-Mediated Electronic Structure Modulation in Multicomponent Covalent Organic Frameworks for Dramatically Promoted Photocatalytic Hydrogen Evolution.

Linkage chemistry is an essential aspect to covalent organic framework (COF) applications; it is highly desirable to precisely modulate electronic structure mediated directly by linkage for efficient COF-based photocatalytic hydrogen evolution, which however, remains substantially challenging. Herein, as a proof of concept, a collection of robust multicomponent pyrene-based COFs with abundant donor-acceptor (D-A) interactions has been judiciously designed and synthesized through molecularly engineering linkage for photogeneration of hydrogen. Controlled locking and conversion of linkage critically contribute to continuously regulating COFs' electronic structures further to optimize photocatalytic activities. Remarkably, the well-modulated optoelectronic properties turn on the average hydrogen evolution rate from zero to 15.67mmol g-1h-1by the protonated quinoline-linked COF decorated with the trifluoromethyl group (TT-PQCOF-CF3). Using diversified spectroscopy and theoretical calculations, we show thatmultiple modifications toward linkagesynergistically lead to the redistribution of charge on COFs with extended π-conjugation and reinforced D-A effect, making TT-PQCOF-CF3a promising material with significantly boosted carrier separation and migration.This study provides important guidance for the design of high-performance COF photocatalysts based on the strategy of linkage-mediated electronic structure modulationin COFs.

In Situ Photodeposition of Gold Nanoparticles with Exposed High-Activity Crystal Facets under Different Sacrificial Agents.

In situ photodeposition presents a powerful approach for integrating noble metal co-catalysts onto semiconductor surfaces. However, achieving precise control over the microstructure of the deposited co-catalyst remains a major challenge. Au nanoparticles (NPs) are deposited onto H-KCNO using HAuCl4 in the presence of various sacrificial agents in this study. Notably, the choice of sacrificial agent decisively influences the exposed crystal facets, loaded content, and particle size of the deposited Au NPs. Importantly, in situ photodeposition under an ethanol solution facilitates the exposure of the highly active (111) and (220) crystal facets of Au. The introduction of Au NPs significantly enhances photocatalytic hydrogen evolution, achieving rates of 4.93, 57.88, and 15.44 μmol/h for H-KCNO/Au-(water, ethanol, and lactic acid), respectively. The observed photocatalytic activity for hydrogen evolution indicates that the exposure of the highly active planes emerges as critical for significant performance enhancement. Photoelectrochemical and photoluminescence measurements suggest that the highly active (111) and (220) crystal facets effectively segregate sites for redox reactions, thereby impeding the recombination of photogenerated electron-hole pairs.

Metal atom-induced microenvironment regulation in polymeric carbon nitride for photocatalytic hydrogen evolution

Metal atom-induced microenvironment regulation in polymeric carbon nitride for photocatalytic hydrogen evolution

Highly-efficient photocatalytic hydrogen evolution enabled by piezotronic effects in SrTiO3/BaTiO3 nanofiber heterojunctions

The synergistic effect between piezoelectric and photocatalytic behaviors presents an interesting avenue to enhance the water-splitting processes for hydrogen production. Through a combination of experimental findings and theoretical calculations, we propose that the piezoelectric field inherent in these materials may decrease the bandgap of piezo-photocatalysts, while the Z-scheme heterojunction structure facilitates electron transfer. Leveraging the synergistic effects of heterojunction formation and piezoelectric assistance, we demonstrate that the incorporated piezoelectric BaTiO3 significantly enhances the hydrogen evolution rate of hybrid SrTiO3/BaTiO3 nanofibers to 1950.2 μmol·g–1·h–1. This surpasses the rates achieved by pure SrTiO3 and BaTiO3 counterparts by 2.4 and 4.1 times, respectively, and notably exceeds those of perovskite-based piezo-photocatalysts ever reported. The present work offers a valuable pathway for piezoelectric-assisted photocatalytic mechanism insight and sustainable hydrogen production, toward a remarkable advancement in pursuit of efficient and environmentally-friendly energy solutions.

Molecular Engineering for Modulating Photocatalytic Hydrogen Evolution of Fully Conjugated 3D Covalent Organic Frameworks

AbstractCovalent organic frameworks (COFs) have recently shown great potential for photocatalytic hydrogen production. Currently almost all reports are focused on two‐dimensional (2D) COFs, while the 3D counterparts are rarely explored due to their non‐conjugated frameworks derived from the sp3 carbon based tetrahedral building blocks. Here, we rationally designed and synthesized a series of fully conjugated 3D COFs by using the saddle‐shaped cyclooctatetrathiophene derivative as the building block. Through molecular engineering strategies, we thoroughly discussed the influences of key factors including the donor‐acceptor structure, hydrophilicity, specific surface areas, as well as the conjugated/non‐conjugated structures on their photocatalytic hydrogen evolution properties. The as‐synthesized fully conjugated 3D COFs could generate the hydrogen up to 40.36 mmol h−1 g−1. This is the first report on intrinsic metal‐free 3D COFs in photocatalytic hydrogen evolution application. Our work provides insight on the structure design of 3D COFs for highly‐efficient photocatalysis, and also reveals that the semiconducting fully conjugated 3D COFs could be a useful platform in clear energy‐related fields.

Molecular Engineering for Modulating Photocatalytic Hydrogen Evolution of Fully Conjugated 3D Covalent Organic Frameworks.

Covalent organic frameworks (COFs) have recently shown great potential for photocatalytic hydrogen production. Currently almost all reports are focused on two-dimensional (2D) COFs, while the 3D counterparts are rarely explored due to their non-conjugated frameworks derived from the sp3 carbon based tetrahedral building blocks. Here, we rationally designed and synthesized a series of fully conjugated 3D COFs by using the saddle-shaped cyclooctatetrathiophene derivative as the building block. Through molecular engineering strategies, we thoroughly discussed the influences of key factors including the donor-acceptor structure, hydrophilicity, specific surface areas, as well as the conjugated/non-conjugated structures on their photocatalytic hydrogen evolution properties. The as-synthesized fully conjugated 3D COFs could generate the hydrogen up to 40.36 mmol h-1 g-1. This is the first report on intrinsic metal-free 3D COFs in photocatalytic hydrogen evolution application. Our work provides insight on the structure design of 3D COFs for highly-efficient photocatalysis, and also reveals that the semiconducting fully conjugated 3D COFs could be a useful platform in clear energy-related fields.

Visible-light harvesting SrTiO3 solid solutions for photocatalytic hydrogen evolution from water.

The fabrication of solid solutions represents a compelling approach to modulating the physicochemical properties of materials. In this study, we achieved the successful synthesis of solid solutions comprising SrTiO3 and SrTaO2N (denoted as (SrTiO3)1-x-(SrTaO2N)x, 0 ≤ x ≤ 1) using the magnesium powder-assisted nitridation method. The absorption edge of (SrTiO3)1-x-(SrTaO2N)x is tunable from 500 to 600 nm. The conduction band minimum (CBM) of (SrTiO3)1-x-(SrTaO2N)x comprises the Ti 3d orbitals and the Ta 5d orbitals, while the valence band maximum (VBM) consists of the O 2p and N 2p orbitals. The microstructure of the (SrTiO3)1-x‑(SrTaO2N)x consists of small nanoparticles, exhibiting a larger specific surface area than the parent compounds of SrTiO3 and SrTaO2N. In the photocatalytic hydrogen evolution reaction (HER) with sacrificial reagents, the activity of solid solutions is notably superior to that of nitrogen-doped SrTiO3 and SrTaO2N. This superiority is mainly attributed to its broad light absorption range and high charge separation efficiency, which indicates its potential as a promising photocatalytic material. Moreover, the magnesium powder-assisted nitridation method exhibits obvious advantages for the synthesis of oxynitrides and bears instructional significance for the synthesis of other nitrogen-containing compounds and even sulfur-containing compounds.

One-step direct construction of S-scheme BaTi2O5/g-C3N4 heterojunction for enhanced photocatalytic hydrogen evolution

One-step direct construction of S-scheme BaTi2O5/g-C3N4 heterojunction for enhanced photocatalytic hydrogen evolution

Photocatalytic dye degradation, H2 evolution, electrical and mechanical performances of mechano-synthesized multifunctional Bi2Te3 nanoparticles: Effect of milling time and thermal treatment

Bi2Te3 nanoparticles are synthesized by mechanical alloying the Bi and Te powders under the Ar and pressed powdered samples are sintered at 573 K. Rietveld refined XRD patterns, FESEM images and EDX spectra reveal the microstructure, morphology and phase purity of the samples. Bandgaps are obtained from the FTIR spectra and a blue shift with size reduction indicates the size confinement effect. The non Debye type ac conductivity and dielectric constant variations with milling time and sintering are measured. The improved photocatalytic degradation efficiency of the sintered sample (83.59 %) using Rhodamine B dye under visible light elucidates reduced porosity effect. The photocatalytic hydrogen evolution efficiencies of these nanoparticles are measured and a probable mechanism is depicted. The highest H2 generation efficiency (1462.5 μmol g−1h−1) is observed with the sintered sample. Microhardness measurement reveals normal indentation size effect. Empirical correlations among electrical conductivity, microhardness and photodegradation are established for the first time.

Molecular Dyad vs Multi‐Component Approach‐Photocatalytic Hydrogen Evolution by Combining Oligothiophene Photosensitizers with [FeFe]‐Hydrogenase Mimics

AbstractA molecular dyad (PS‐CAT) consisting of a metal‐free photosensitiser (PS) and a [FeFe]‐hydrogenase‐inspired [Fe2S2] cluster (CAT) has been synthesized for hydrogen evolution under visible light irradiation. The electrochemical properties of PS‐CAT in the absence and presence of acid were investigated by CV and IR‐SEC. The ground state and excited state photophysical properties of PS and PS‐CAT, and the non‐chemically connected reference system [PS, CAT] were investigated to elucidate the effect of a covalent linkage between PS and CAT on the electronic communication and hence on the catalytic performance. The photo‐relaxation pathway of PS‐CAT was revealed computationally by scalar‐relativistic time‐dependent density functional theory simulations. These studies are complemented by comparative analyses of photocatalytic hydrogen evolution between PS‐CAT and [PS, CAT] under visible light irradiation.

Anchoring Single-Atomic Metal Sites in Metalloporphyrin-Based Covalent Organic Frameworks for Enhanced Photocatalytic Hydrogen Evolution.

A photoactive covalent organic framework (COF) was built from metalloporphyrin and bipyridine monomers and single-atomic Pt sites were subsequently installed. Integrating photosensitizing metalloporphyrin and substrate-activating Pt(bpy) moieties in a single solid facilitates multielectron transfer and accelerates photocatalytic hydrogen evolution with a maximum production rate of 80.4 mmol h-1 gPt-1 and turnover frequency (TOF) of 15.7 h-1 observed. This work demonstrates that incorporation of single-atomic metal sites with photoactive COFs greatly enhances photocatalytic activity and provides an effective strategy for the design and construction of novel photocatalysts.

Preparation and Photocatalytic Hydrogen Evolution Performance Study of NENU‐5/CuBr/Graphdiyne Tandem S‐Scheme Heterojunction

Graphdiyne (GDY) has been widely applied in the field of photocatalytic hydrogen production due to its unique chemical structure and excellent photoelectric performance. Herein, CuBr is used as a catalytic substrate to prepare CuBr/GDY through a cross‐coupling reaction, and a novel NENU‐5/CuBr/GDY tandem S‐scheme heterojunction photocatalyst is constructed at low temperature. The NENU‐5/CuBr/GDY heterojunction exhibits significantly enhanced activity in photocatalytic hydrogen evolution, with hydrogen evolution reaching 226.62 μmol in 5 h, which is 4.7 and 12.6 times greater than that of pure GDY and NENU‐5, respectively. Comprehensive evaluation of electrochemical, photoluminescence, and time‐resolved photoluminescence indicates that the enhanced activity of the NENU‐5/CuBr/GDY composite catalyst is attributed to high photocurrent response and low electrical resistance, which increases the efficiency of photogenerated charge separation. Additionally, density functional theory calculations and ultraviolet photoelectron spectroscopy propose the possibility of constructing the NENU‐5/CuBr/GDY tandem S‐scheme heterojunction structure. In summary, this work provides valuable ideas into tandem heterojunctions for photocatalytic hydrogen production.

Surface-Grafted Single-Atomic Pt-Nx Complex with a Precisely Regulating Coordination Sphere for Efficient Electron Acceptor-Inducing Interfacial Electron Transfer.

Based on the electron-withdrawing effect of the Pt(bpy)Cl2 molecule, a simple post-modification amide reaction was firstly used to graft it onto the surface of NH2-MIL-125, which formed a highly efficient electron acceptor that induced the conversion of the photoinduced charge migration pathway from internal BDC→TiOx migration to external BDC→PtNx migration, significantly improving the efficiency of photoinduced electron transfer and separation. Furthermore, precise control over the first coordination sphere of Pt single atoms was achieved using further post-modification with additional bipyridine to investigate the effect of Pt-Nx coordination numbers on reaction activity. The as-synthesized NML-PtN2 exhibited superior photocatalytic hydrogen evolution activity of 7.608 mmol g-1 h-1, a remarkable improvement of 225 and 2.26 times compared to pristine NH2-MIL-125 and NML-PtN4, respectively. In addition, the superior apparent quantum yield of 4.01% (390 nm) and turnover frequency of 190.3 h-1 (0.78 wt% Pt SA; 129 times compared to Pt nanoparticles/NML) revealed the high solar utilization efficiency and hydrogen evolution activity of the material. And macroscopic color changes caused by the transition of carrier migration paths was first observed. It holds profound significance for the design of MOF-Molecule catalysts with efficient charge carrier separation and precise regulation of single-atom coordination sphere.

Amorphous nitrogen-doped carbon layers forming the interfacial channel for rapid charge transfer in ZnIn2S4/BiVO4 Z-scheme photocatalyst for enhancing organic pollutants degradation with simultaneous hydrogen evolution

Efficient photocatalytic hydrogen evolution from the organic wastewater represents an ideal solution for simultaneously addressing energy shortages and environmental pollution. However, the sluggish transport of photogenerated carriers at contact interface poses a key obstacle to enhancing photocatalytic activity. Here, ZnIn2S4/BiVO4@N-C (ZIS/BVO@N-C) Z-scheme photocatalysts were successfully constructed by a simple hydrothermal-impregnation method. ZIS/BVO@N-C-10% demonstrated outstanding photocatalytic performance, achieving a hydrogen evolution rate of 2695.68 μmol·g−1·h−1 and a degradation rate of 492.96 mmol·g−1·h−1 under visible light, surpassing those of ZIS (851.52 μmol·g−1·h−1 and 174.83 mmol·g−1·h−1) and ZIS/BVO-10% (1228.98 μmol·g−1·h−1 and 277.78 mmol·g−1·h−1). Characterization results and density functional theory (DFT) calculations revealed that the introduction of the N-C layer reduced interfacial impedance and enhanced the strength of interfacial electric field, overcoming the interfacial barrier and improving the photogenerated separation and migration efficiency at the interface, and ultimately enhancing the photocatalytic activity of ZIS/BVO@N-C. Based on experimental and characterization results, the photocatalytic mechanism of ZIS/BVO@N-C Z-scheme has been proposed. Furthermore, ZIS/BVO@N-C exhibited excellent stability, highlighting its potential for practical applications. This work also presents a new strategy for designing highly active Z-scheme photocatalysts for organic wastewater treatment and simultaneous hydrogen energy recovery.

Surface‐Grafted Single‐Atomic Pt‐Nx Complex with a Precisely Regulating Coordination Sphere for Efficient Electron Acceptor‐Inducing Interfacial Electron Transfer

Based on the electron‐withdrawing effect of the Pt(bpy)Cl2 molecule, a simple post‐modification amide reaction was firstly used to graft it onto the surface of NH2‐MIL‐125, which formed a highly efficient electron acceptor that induced the conversion of the photoinduced charge migration pathway from internal BDC→TiOx migration to external BDC→PtNx migration, significantly improving the efficiency of photoinduced electron transfer and separation. Furthermore, precise control over the first coordination sphere of Pt single atoms was achieved using further post‐modification with additional bipyridine to investigate the effect of Pt‐Nx coordination numbers on reaction activity. The as‐synthesized NML‐PtN2 exhibited superior photocatalytic hydrogen evolution activity of 7.608 mmol g−1 h−1, a remarkable improvement of 225 and 2.26 times compared to pristine NH2‐MIL‐125 and NML‐PtN4, respectively. In addition, the superior apparent quantum yield of 4.01% (390 nm) and turnover frequency of 190.3 h−1 (0.78 wt% Pt SA; 129 times compared to Pt nanoparticles/NML) revealed the high solar utilization efficiency and hydrogen evolution activity of the material. And macroscopic color changes caused by the transition of carrier migration paths was first observed. It holds profound significance for the design of MOF‐Molecule catalysts with efficient charge carrier separation and precise regulation of single‐atom coordination sphere.