Phase-shifting Speckle Interferometry Research Articles

Accurate dynamic 3D deformation measurement based on the synchronous multiplexing of polarization and speckle metrology.

An accurate dynamic 3D deformation measurement method realized by the combination of phase-shifting speckle interferometry and speckle correlation is proposed. By converting the speckle field and the reference field into a circular polarized and linear polarized state, the three-step phase-shifting speckle interferograms and one specklegram were recorded directly and simultaneously within a single image by using a polarization camera. Then, the out-of-plane deformation was demodulated from the synchronous phase-shifting fringe patterns, and the in-plane deformation was measured by performing correlation calculations by using specklegrams with the effect of the reference field ignored. Thus, the full-field 3D deformation was obtained precisely. Experimental results demonstrated the accuracy and dynamic measurement ability of the proposed method, which is compact and feasible for actual dynamic scenes.

Surface Displacement Measurements of Artworks: New Data Processing for Speckle Pattern Interferometry

Curators have developed preventive conservation strategies and usually try to control the temperature (T) and relative humidity (RH) variations in the museum rooms to stabilise the artworks. The control systems chosen by museums depend on the size and age of the building, the financial means and the strategies that can be adapted. However, there is a lack of methods that can monitor mechanical changes or chemical reactions of objects in real-time or regularly. It would therefore ideally be preferable to monitor each of them to alert them to preserve them. For this purpose, a non-destructive, non-contact, full-field technique, Digital Holographic Speckle Pattern Interferometry (DHSPI), has already been developed and allows direct tracking of changes on the surface of artworks. This technique is based on phase-shifting speckle interferometry and gives the deformation of the surface below the level of the micro-meter of the analysed object. In order to monitor the deformation continuously, a large number of images are acquired by DHSPI and have to be processed. The existing process consists of removing noise from the interferogram, unwrapping this image, and deriving and displaying a 2D or 3D deformation map. In order to improve the time and accuracy of processing the imaging data, a simpler and faster processing method is developed. Using Matlab®, a denoising methodology for the interference pattern generated during data acquisition is created, based on a stationary wavelet transform. The unwrapped image is calculated using the CPULSI (Calibrated Phase Unwrapping based on Least-Squares and Iterations) algorithm as it gives the fastest results among the tested methods. The unwrapped phase is then transformed into surface displacement. This process performs these steps for each interferogram automatically. It allows access to 2D or 3D deformation maps.

Determination of vibration amplitudes from binary phase patterns obtained by phase-shifting time-averaged speckle shearing interferometry.

Speckle shearing interferometry (shearography) is a full-field strain measurement technique that can be used in vibration analysis. In our case, we apply a method that combines the time-averaging and phase-shifting techniques. It produces binary phase patterns, where the phase changes are related to the zeroes of a Bessel J0 function, typical of time-averaging. However, the contrast and resolution are better compared to traditional time-averaging. In a previous paper, we have shown that this is particularly useful in vibration testing performed under industrial conditions, because fringe patterns are noisier than in quiet laboratory environments. This paper goes a step further in proposing a processing method for estimating the vibration amplitude, for helping non-experts to identify vibration modes. Since shearography measures the spatial derivative of displacement, spatial integration is required. Prior to that, different processes like denoising, binarization, automated nodal line detection, and amplitude assignment are applied. We analyze the performance of the method on synthetic and experimental data, in the function of noise level and fringes density. Results on data acquired in an industrial environment illustrate the good performances of the proposed method.

Surface topography measurement of plasma-facing materials by dual-wavelength phase-shifting speckle interferometry technique

A dual-wavelength phase-shifting speckle interferometry approach has been proposed to diagnose the topography of plasma-facing materials (PFMs) in tokamak. The conventional speckle interferometric surface measurement, which uses single-wavelength, can offer excellent vertical resolution, but limitation in measuring large height step and phase ambiguity would occur during their application. To solve the problem, a dual-wavelength method was developed. Experiments were conducted on molybdenum (Mo) sample, which is related to PFMs of experimental advanced superconducting tokamak (EAST), and a laser ablation method was adopted to simulate the erosion happed on PFMs. The laser ablation craters were measured by both single-wavelength and dual-wavelength phase-shifting speckle interferometry, and a multistep phase-shifting method has been investigated for their effectiveness on reducing noise in calculating the phase map. This work demonstrates the superiority of the dual-wavelength speckle interferometry and the feasibility of applying the measurement system in topographic measurement of PFMs in EAST.

The measurement of plasma-facing materials’ topography variation by means of temporal phase-shifting speckle interferometry technique

Temporal phase-shifting speckle interferometry is proposed to measure plasma-facing materials’ (PFMs) topography variation in tokamak. In this approach, laser ablation method is used to simulate erosion and redeposition, and polished molybdenum/tungsten (Mo/W) samples which are related to PFMs have been tested. The geometric topography of the ablated area was reconstructed successfully via a numerical model developed in this work. The results demonstrate the feasibility of temporal phase-shifting speckle interferometry applied to topography measurement of PFMs.

Determination of the 3D fields of displacements by the method of phase-shifting speckle interferometry

For 3D speckle interferometers, we propose a simplified procedure aimed at recording and processing speckle interferograms with single phase shift, which requires the minimum number of images. The results of experiments are presented to confirm the efficiency of the proposed procedure.

Phase shifting speckle interferometry for dynamic phenomena

The paper presents an algorithm able to retrieve the phase in speckle interferometry by a single intensity pattern acquired in a deformed state, provided that the integrated speckle field is resolved in the reference condition in terms of mean intensity, modulation amplitude and phase. The proposed approach, called throughout the paper "one-step", can be applied for studying phenomena whose rapid evolution does not allow the application of a standard phase-shifting procedure, which, on the other hand, must be applied at the beginning of the experiment. The approach was proved by an experimental test reported at the end of the paper.

Elastic characterization of orthotropic plates of any shape via static testing

The paper presents an inverse procedure for identifying elastic properties of isotropic or orthotropic materials from the full-field measurement of the surface displacements of plates under flexural loading configurations. The procedure is based on a numerical–experimental optimisation process which minimizes an error function defined by subtracting the experimental data from the outputs of the numerical analysis. In each iteration the optimisation process updates the values of the elastic constants in a finite element model of the specimen used in the experimental tests. The unknown parameters are simultaneously identified by a single test and without damaging the structural integrity of the specimen. The possibility of using the methodology for characterizing any-shaped plates was investigated. The applicability and the robustness of the procedure were carried out on aluminum and unidirectional Graphite/PEEK laminate specimens. Phase-shifting speckle interferometry was employed to detect the out-of-plane displacement field of a portion of the observed surface of the specimen.

Speckle interferometry diagnostic for erosion/redeposition measurement in tokamaks

For erosion/redeposition measurement in tokamaks, an optical method based on temporal phase shifting speckle interferometry is in development at CEA Cadarache. Measurement performed on carbon material allowed us to develop a procedure for erosion/redeposition measurement during a plasma discharge. In order to measure reliable amount of eroded and redeposited material in tokamaks during a plasma discharge, the optical method has been adapted to tokamaks environment. Such improvements allowed to perform shape measurements on ITER divertor mock-up and erosion measurement on the Toroidal Pumped Limiter in realistic tokamak conditions.

Global approach for fitting 2D interferometric data

The present paper describes a fitting procedure capable of providing a smooth approximation of experimental data distributed on a bidimensional domain, e.g. the typical output of an interferometric technique. The procedure is based on the optimization of an analytical model defined on the whole domain by the B-spline formulation. In the paper rectangular, circular and polygonal convex domains are considered in details, but, according to the need of the operating conditions, the procedure can be extended to domains of different shapes. The proposed procedure was initially calibrated by an analytical case study: a thin square plate simply supported along the edges and loaded by a uniform pressure. Subsequently, by the operative parameters defined by the analyses carried out on the analytic data, the fitting procedure was applied on experimental data obtained by phase shifting speckle interferometry.

High-speed dynamic speckle interferometry: phase errors due to intensity, velocity, and speckle decorrelation

The recently developed technique of high-speed phase-shifting speckle interferometry combined with temporal phase unwrapping allows dynamic displacement fields to be measured, even for objects containing global discontinuities such as cracks or boundaries. However, when local speckle averaging is included, small phase errors introduced at each time step are accumulated along the time axis, yielding total phase values that depend strongly on the speckle rereference rate. We present an analysis of the errors introduced in the phase evaluation by three sources: intensity errors, velocity errors, and speckle decorrelation. These errors are analyzed when they act both independently and together, for the most commonly used phase-shifting algorithms, with computer-generated speckle patterns. It is shown that, in a controlled out-of-plane geometry, errors in the unwrapped phase map that are due to speckle decorrelation rise as the time between rereferencing events is increased, whereas those due to intensity and velocity errors are reduced. It is also shown that speckle decorrelation errors are typically more important than the intensity and velocity errors. These results provide guidance as to the optimal speckle rereferencing rate in practical applications of the technique.

Elastic characterization of anisotropic materials by speckle interferometry

In this paper we present an experimental procedure for the elastic characterization of thin anisotropic plates. The procedure allows the determination of the elastic constants of isotropic materials (metals and ceramics) and orthotropic materials (composite laminae). Moreover, the flexural compliances of completely anisotropic uncoupled materials (most of composite laminates) can also be measured. The tests are carried out by applying a concentrated force to the specimen supported by three spheres. The stress components are evaluated by simply measuring the applied load, while the strain fields are measured by digital phase-shifting speckle interferometry. The experimental procedure is entirely controlled by a virtual instrument developed for this purpose in the National Instruments LabVIEW® environment, which runs on a personal computer interfaced with a standard black and white CCD camera. By means of the speckle interferometer, the whole field of the out-of-plane displacements is acquired; the curvatures, and hence the strain components, are obtained by two subsequent numerical differentiations. The numerical processing of the experimental data was carried out in the Mathematica™ environment. The results obtained on a steel specimen and on a composite laminate are reported.

Phase shifting speckle interferometry for determination of strain and Young’s modulus of mineralized biological materials: a study of tooth dentin compression in water

Mineralized biological materials have complex hierarchical graded structures. It is therefore difficult to understand the relations between their structure and mechanical properties. We report the use of electronic speckle pattern-correlation interferometry (ESPI) combined with a mechanical compression apparatus to measure the strain and Young's modulus of root dentin compressed under water. We describe the optomechanical instrumentation, experimental techniques and procedures needed to measure cubes as small as 1 x 1 x 2 mm. Calibration of the method is performed using aluminum, which shows that the measurements are accurate within 3% of the compression modulus reported for standard aluminum 6061. Our results reveal that the compression moduli of root dentin from the buccal and lingual sides of the root are quite different from the moduli of the interproximal sides. Root dentin from interproximal locations is found to have an average modulus of 21.3 GPa, which is about 40% stiffer than root dentin from the buccal and lingual locations, found to have a modulus of 15.0 GPa. Our approach can be used to map deformations on irregular surfaces, and measure strain on wet samples of varying sizes. This can be extended to the study of other biological materials including bone and synthetic biomaterials.

Using speckle interferometry to study longitudinal surface displacements in metallic beam samples

A method is proposed for checking the reliability of a quantitative estimate of longitudinal displacements in metallic beam samples when they are investigated by electronic speckle interferometry and phase-shifting speckle interferometry. Theoretical and experimental results are presented for the investigation of longitudinal surface displacements of samples by electronic difference speckle interferometry and phase-shifting speckle interferometry. © 2004 Optical Society of America

Measurement of sub-surface delaminations in carbon fibre composites using high-speed phase-shifted speckle interferometry and temporal phase unwrapping

A high-speed phase-shifted speckle interferometer has been developed recently for studying dynamic events. Speckle interferograms are continuously recorded by a CCD camera operating at 1 kHz with temporal phase shifting carried out by a Pockels cell running at the same frequency. Temporal phase unwrapping through sequences of more than 1000 frames allows the determination of time-varying absolute displacement maps. This paper presents the application of this speckle interferometry system to the detection and measurement of sub-surface delamination defects in carbon fibre specimens. The influence of re-referencing the temporal phase unwrapping algorithm after different time intervals is analysed to reduce the random phase errors produced by speckle decorrelation and vibration. The performance of several phase-shifting algorithms to minimize the influence of the vibration noise caused by the vacuum pump used to load the specimen is also investigated.

A simple method for measuring the random variation of aninterferometer

A simple technique for measuring the random noise of an interferometricmeasurement is presented. The method is based on a filtering technique andthe use of a low-pass convolution kernel. It is shown that the method givesa deterministic fraction of the real noise present in the experimentaldata. The evaluation of the probability density allows the determination ofthe enlarging constant for specifying the confidence level. Experimentalresults are reported in the case of moderately noisy and significantlynoisy interferometric techniques: phase shifting interferometric testingof smooth surfaces and phase shifting speckle interferometry.

Systematic errors of phase-shifting speckle interferometry

A theoretical and numerical investigation of the systematic phase errors in phase-shifting speckle interferometry is presented. The theoretical investigation analyzes the behavior of some systematic error induced by intensity variations in two cases of data-computing techniques. The first case deals with the technique in which the phase change is computed, unwrapped, and then linearly filtered; the second case deals with the technique in which the data are linearly filtered before the arctangent calculation and then unwrapped. With the first filtering technique it is shown that it is preferable when the phase change is of relatively low spatial frequency, leading to a particularly accurate method. With the second case it is demonstrated that an important parameter of speckle interferometry is the modulation factor of the interference frame that induces phase errors when the data are filtered before the arctangent calculation. We show that this technique is better than the first when the phase change is composed of high-spatial-frequency variations. The theoretical investigation of the two techniques is compared with numerical simulations, considering the frequency characteristics of the phase change, and this shows a good match between theory and simulations.

Phase evaluation of speckle patterns during continuous deformation by use of phase-shifting speckle interferometry

A method for measurement of continuous displacements that uses phase-shifting speckle interferometry is presented. The initial random phase of the speckle pattern is evaluated by phase shifting before deformation. The changing phase thereafter is evaluated from only one image at a time by a least-squares algorithm. The technique can be used for measuring transients and other dynamic events, heat expansion as well as other phenomena, for which it is difficult to accomplish phase shifting during deformation. Theory along with computer simulations and experimental results are described.

Reconstruction of surfaces from phase-shifting speckle interferometry: Bayesian approach

The reconstruction of surfaces from speckle interferometry data is a demanding data-analysis task that involves edge detection, edge completion, and image reconstruction from noisy data. We present an approach that makes optimal use of the experimental information to minimize the hampering influence of the noise. The experimental data are then analyzed with a combination of wavelet transform and Bayesian probability theory. Nontrivial examples are presented to illustrate the proposed technique.

Comparative measurement by phase-shifting digital speckle interferometry using holographically generated reference wave

A new method in digital speckle pattern interferometry is in- troduced. It is a two-stage process. In the first stage, two states (un- loaded and loaded states) of the master object are recorded in a holo- graphic plate using the usual holographic arrangement. In the second stage, various phase stepping algorithms are applied, using the recon- structed wavefronts of the master object as a holographic optical ele- ment to produce reference wave fields in the comparison process. The method is investigated, and its viability is demonstrated by experimental results and computer simulations. © 1999 Society of Photo-Optical Instrumenta- tion Engineers. (S0091-3286(99)01507-X)