Perpendicular Fiber Research Articles

Static in-situ curing characteristics of CFRP based on near infrared laser

Study on static in-situ curing characteristics of CFRP based on near infrared laserThe quick curing method of carbon fibre reinforced plastics (CFRP) is one of the hotspots in current research. A static in-situ curing method for CFRP prepreg based on near-infrared laser was put forward in this study. The in-situ curing structural characteristics and the mechanism of CFRP were investigated through real-time surface temperature measurement, COMSOL temperature field simulation, 3D measurement of curing morphology and resin curing degree test. The thermal conductivity of the CFRP along the fiber direction is considerably higher than that along the perpendicular fiber direction. As a result, the temperature profile in the plane takes on an elliptical shape. During the transfer, the temperature field gradually decreases, resulting in an ellipsoidal 3D high-temperature distribution. The different shrinkage phenomena in the different curing regions between the layers lead to an irregular ellipsoidal solidification morphology of the unidirectional CFRP. The temperature in the center of the heat affected zone increases as a power exponential function with time. The area and depth of the heat-affected zone increases with the laser power, and the curing area is positively correlated with the degree of curing. As a result, curing temperature governing equations based on laser power and layer thickness have been proposed, while relationship equations based on laser power, curing depth and curing morphology have been developed. In addition, prediction equations based on curing morphology have been developed for curing degree, in order to achieve precise curing of CFRP.

Material removal and damage formation mechanisms induced by periodic indentation during ultrasonic vibration-assisted scratching of SiCf/SiC composites

Fiber-reinforced ceramic matrix composites (CMCs) exhibit high hardness, brittleness, heterogeneity, and anisotropy. This study explores the material removal and damage formation mechanisms during ultrasonic vibration-assisted scratching of SiCf/SiC composites through experimental and micro-finite element simulations. The research reveals that high-frequency periodic indentation-separation of abrasive grain influences stress transfer and crack propagation, which are affected by the interfacial layer and fiber orientation. Crack deflection plays a crucial role in material removal and determines the amplitude of normal scratching force. Stress transfer interference primarily governs damage formation, with more severe damage occurring along the longitudinal and transverse fiber directions due to secondary stress concentration and crack deflection. In contrast, scratching along the perpendicular fiber direction requires higher normal forces due to residual adjacent phase materials, but results in more controlled material removal and less damage. The study provides insights into optimizing the ultrasonic vibration-assisted machining of CMCs to minimize damage.

Probability Prediction of Curing Process-Induced Deformation for V-Shape Composite Structures Based on FEM Method and Data Mining.

Continuous fiber-reinforced composites are increasingly used in industry for their superior specific modulus and strength. The curing process-induced deformation (PID) has been a critical problem during manufacturing, which always exhibits dispersed values even if the curing process curve and structural parameters remain consistent. This work conducted probability prediction of PID for V-shape composite structures based on the FEM method and data mining. A sequential coupling thermal-chemical-mechanical coupling FE model is established in ABAQUS. The prediction accuracy of the included angle between two sides is verified by the experimental results. Material parameter uncertainties are considered for V-shape structures with different radii and thicknesses. Based on the dataset from the FE model, a decision tree is established and trained to analyze the sensitivity and to predict the probability distribution of PID. The results show that PID increases with the coefficients of thermal expansion in the in-plane perpendicular fiber direction and out-of-plane normal direction. The data-mining method is accurate enough for the PID prediction, and its efficiency provides an additional calculation option in engineering applications.

Comparison of damage mechanisms in chopped strand mat and woven roving mat composites under cyclic tension

AbstractGlass fiber reinforced polymer (GFRP) composites with chopped strand mat (CSM) and woven roving mat (WRM) reinforcements are widely used in high‐pressure piping due to their favorable strength‐to‐weight ratio. However, cyclic loading from vibrations and pulsating forces can induce internal microstructural damage, ultimately leading to performance degradation. A thorough understanding of this damage mechanism is imperative for its mitigation, necessitating a detailed examination. The present study aims to investigate the fatigue response and damage mechanisms in CSM and WRM composites subjected to tension‐tension cyclic loading. Scanning electron microscopy analysis of edge sections revealed the development of perpendicular microcracks in both composites. CSM composites exhibited fatigue cracks parallel to the loading direction and higher levels of parallel interface debonding compared to perpendicular matrix cracks. Finite element analysis of the representative volume element revealed the role of shear stress in the matrix in initiating parallel cracks, thereby explaining the damage initiation mechanism in CSM. These findings highlight the distinct damage mechanisms arising from the differing fiber arrangements in CSM and WRM composites, providing valuable insights for optimizing their performance under cyclic loading conditions.Highlights Fatigue response of CSM and WRM was influenced by fiber orientation and weaving pattern. Perpendicular fibers were the most probable fibers to have their interface form a crack. Fatigue cracks parallel to the direction of loading were observed in CSM composites. Quantified the true 3D internal microstructural damages for the first time.

Characterization, quantitative evaluation, and formation mechanism of surface damage in ultrasonic vibration assisted scratching of Cf/SiC composites

Carbon fiber reinforced silicon carbide ceramic matrix composites (Cf/SiC composites) have a wide range of applications in aerospace, nuclear energy, braking systems owing to its excellent mechanical performance. Nevertheless, the hardness, brittleness, heterogeneity, and anisotropy of Cf/SiC composites give rise to difficulties in machining them. In addition, the characterization and formation mechanism of surface damage in the grinding of Cf/SiC composites have not been fully elucidated. The purpose of this paper is to provide a characterization method for surface damage of Cf/SiC composites and an evaluation index for surface edge chipping damage (SECD) through conventional scratching (CS) / ultrasonic vibration assisted scratching (UVAS) tests with single abrasive. Towards revealing the surface damage behavior of Cf/SiC composites during scratching, as well as the impact of fiber orientation on surface damage. The findings indicate that main forms of surface damage of Cf/SiC composites in single abrasive scratching are fiber breakage, fiber fracture-shedding, fiber fracture, fiber-matrix interface debonding, interface fragmentation, matrix cracking, and matrix microcracks. Further, ultrasonic vibration could help to suppress the SECD, and the SECD factor was smallest when scratching along the perpendicular fiber. Furthermore, the fiber orientation can significantly affect the scratching force and cross-sectional area of scratches on Cf/SiC composites via single abrasive scratching. The tangential scratching force was usually smaller as compared to the normal scratching force, and the cross-sectional area of scratches in UVAS is smaller than that in CS. Based on the above findings, this study elucidates the formation and evolution of surface damage after scratching under different fiber orientations, filling the research gap in surface damage under ultrasonic assisted machining of Cf/SiC composites and providing technical guidance for the machining.

Reactive Cell Electrospinning of Anisotropically Aligned and Bilayer Hydrogel Nanofiber Networks.

Structured hydrogels that incorporate aligned nanofibrous morphologies have been demonstrated to better replicate the structures of native extracellular matrices and thus their function in guiding cell responses. However, current techniques for nanofiber fabrication are limited in their ability to create hydrogel scaffolds with tunable directional alignments and cell types/densities, as required to reproduce more complex native tissue structures. Herein, we leverage a reactive cell electrospinning technique based on the dynamic covalent cross-linking of poly(ethylene glycol methacrylate (POEGMA) precursor polymers to fabricate aligned hydrogel nanofibers that can be directly loaded with cells during the electrospinning process. The scaffolds were found to support high C2C12 myoblast viabilities greater than 85% over 14 days, with changes in the electrospinning collector allowing for the single-step fabrication of nonaligned, aligned, or cross-aligned nanofibrous networks. Cell aspect ratios on aligned scaffolds were found on average to be 27% higher compared to those on nonaligned scaffolds; furthermore, cell-loaded bilayer scaffolds with perpendicular fiber alignments showed evidence of enabling localized directional cell responses to individual layer fiber directions while avoiding delamination between the layers. This fabrication approach thus offers potential for better mimicking the structure and thus function of aligned and multilayered tissues (e.g., smooth muscle, neural, or tendon tissues).

Influence of surface nanotopography and wettability on early phases of peri-implant soft tissue healing: an in-vivo study in dogs

BackgroundIt is well established that nanotopography and wettability of implant surfaces contribute to osseointegration and long-term implant success. However, the effects of a hydrogenated surface with nanotubular and superhydrophilic properties on peri-implant soft tissue remain unclear. This study was designed to study the impact of a modified abutment surface on early soft tissue integration compared with a machined surface.MethodsThirty-six implants were placed at the bone level in the bilateral mandible of six beagles, followed by healing abutments belonging to the standard machined Ti-6Al-4V alloy abutments (TC4-M), anodized abutments with nanotubes (TC4-Nano), and hydrogenated abutments (TC4-H/Nano) groups, which were randomly screwed to the implants. After two and four weeks of wound healing, the animals were euthanized for histological evaluation.ResultsA superhydrophilic nanotubular surface developed on the hydrogenated abutment. Histological and histometric analyses revealed similar peri-implant soft tissue healing and dimensions for the three types of abutments at two and four weeks. Connective tissue (CT) length was longer around TC4-H/Nano abutments compared with standard abutments; however, the differences were not statistically significant. Moreover, collagen fibers in the TC4-H/Nano group extended and were attached perpendicularly to the superhydrophilic surface.ConclusionsOur results revealed that the soft tissue interface adjacent to the hydrogenated abutment is comparable to that of the machined abutment. A tendency of increased CT length and perpendicular collagen fibers was observed around the modified abutment. This study suggests that nanotubular/superhydrophilic surfaces could be a promising modification to enhance soft tissue sealing. However, comprehensive studies should be conducted to evaluate the peri-implant soft tissue around the modified abutment immunohistochemically, histopathologically, and clinically.

Bending responses of self-shaping wood bilayers: comparison between adsorption and desorption processes

Inspired by biological materials, the self-shaping wood composites induced by relative humidity (RH) have been investigated over the last decade. In this study, a wood bilayer was fabricated by assembling two layers with perpendicular fiber orientation in a series of thickness ratios and initial moisture contents (iMC). The self-shaping response of the wood bilayer was explored as a function of its configuration, and the discrepancies between moisture adsorption and desorption processes were clarified. Higher iMC limited the evolution of curvature. During both the adsorption and desorption processes, a reversed bending response was observed, and there was a hysteretic bending behavior between them. Repeatable bending was achieved during the cyclic ad/desorption process, and a larger hysteresis loop was observed at a lower thickness ratio. Finite-element analysis showed that the maximum stress occurred at the interface between the active and passive layers, and larger thickness ratios had lower maximum stress. In addition, the bilayer composed of a 200 μm passive layer and a 400 μm active layer with 0.6% iMC was found to be the most sensitive to RH change. The results of this study elucidate the moisture-dependent bending response of wood bilayers and provide the possibility of precisely controlling the curvature of self-shaping wood composites in industrial applications.

The influence of yarn fiber volume fraction, shear angle, and yarn spacing on crack propagation resistance of plain‐woven fabric‐reinforced epoxy composites

AbstractThis study investigated the effect of fabric parameters on crack propagation in plain‐woven e‐glass reinforced epoxy composite plates. Through numerical analyses, the study contributes to understanding the effect of fabric structure on crack propagation and adopting a more precise approach in the design of composite materials. The yarn fiber volume fraction, shear angle, and yarn spacing parameters were selected as variables for the plain‐woven fabric, and material properties were determined for each parameter using the composite homogenization method. A finite element model was created using the Ansys software package, and stress intensity factors (SIFs) and tear stress values were obtained under mode I loading to investigate the effects of fabric structure on crack propagation. The results showed that as the yarn fiber volume fraction ratio increased, the SIF values decreased and the T‐stress values increased. When evaluated according to the shear angle of the yarn, the lowest SIF value was obtained for the 0‐degree shear angle. The same was observed for T‐stress values as well. Additionally, compared to the fabric structure aligned along the X‐axis, a significant decrease occurred in the SIF value due to the perpendicular fiber density increase to the crack propagation direction with symmetric orientation.

PULM2: Combining Extracorporeal Lung and Kidney Support: Evaluation of Fibre Configurations on Gas Exchange Preservation for the Development of a Novel Highly Integrated Device (RenOx)

Background: Combined lung and kidney dysfunction are frequent in extracorporeal membrane oxygenation (ECMO) patients affecting up to 70% of them. Current treatment relies on the use of two separate circuits combining ECMO and renal replacement therapy, increasing infection risks and the use of artificial surfaces. Therefore, we aim to develop a novel artificial lung that integrates lung and kidney support in a single device combining oxygenation and hemodialysis fibers. Thus, we analyzed how many oxygenation fibers could be substituted by hemodialysis fibers while still maintaining 90% of the oxygenator’s gas exchange capacity and the effect fiber configuration has on oxygen (O2) and carbon dioxide (CO2) transfer. Methods: Fiber bundles were composed of oxygenation fiber mats (Oxyplus™ 90/200, 3M) stacked perpendicularly at a 90° angle and/or crossed at a 24° angle on top of each other. We manufactured bundles with all oxygenation fibers open and bundles with oxygenation fibers closed in a way that they could not contribute to gas exchange, simulating hemodialysis fibers. Bundles in perpendicular configuration had 100% of fibers open (Oxy100P), 50% of fibers closed (Oxy50P), or 25% of fibers closed (Oxy75P), Figure 1. Bundles in crossed configuration had all fibers open (Oxy100C) or 33% of fibers closed (Oxy67C). Bundles were tested for gas exchange performance following in-vitro blood tests according to ISO 7199:2016. Results: Our results show that bundles with 25% of oxygenation fibers closed in perpendicular configuration were able to still maintain 90% of the O2 exchange and 80% of the CO2 exchange capacity of our oxygenator. Bundles with 25% oxygenation fibers closed had no statistically significant difference in O2 or CO2 transfer compared to a fully open oxygenator with the same fiber configuration, Figure 2. Additionally, Oxy75P bundles were able to keep O2 delivery above 55 mL/LBlood flow and CO2 removal above 52 mL/LBlood flow up to 140 mL/min. Fiber configuration did not affect gas exchange for fully open bundles, however, configuration significantly influenced O2 and CO2 exchange for bundles with closed fiber layers. Closing fibers in perpendicular configuration resulted in a lower decrease in gas transfer. Below 140 mL/min, this was demonstrated by a similar decrease in O2 transfer of 20% when 50% of perpendicular fibers or 33% of crossed fibers were closed Conclusions: We analyzed the effect of replacing oxygenation fibers with hemodialysis fibers on gas exchange efficiency. Our results demonstrate that 25% of oxygenation fibers in a perpendicular configuration could be replaced by hemodialysis fibers while still maintaining 90% of the O2 exchange of our oxygenator. Moreover, this type of bundle kept O2 delivery above 55 mL/LBlood flow up to 140 mL/min. This shows that gas exchange can be preserved to a desirable extent when oxygenation fiber layers are replaced. This is a step towards combining lung and kidney support in a single device.Figure 1. Illustration of a device combining extracorporeal lung and kidney support. Oxygen flows through the lumen of oxygenation fibers and dialysate flows inside hemodialysis fibers. In this work, fiber bundles were manufactured with a perpendicular and/or crossed configuration having a varying number of oxygenation fiber layers closed, simulating hemodialysis fibers (open fibers in white and closed fibers in blue). Perpendicular bundles had 50% of fibers closed (Oxy50P), 25% of fibers closed (Oxy75P), or 100% of fibers open (Oxy100P), while crossed bundles had 33% of fibers closed (Oxy67C), or all fibers open (Oxy100C).Figure 2. Oxygen exchange performance mL/LBlood flow ± standard deviation from the mean (n = 10) for bundles with different fiber configurations. We found no statistically significant difference in mean oxygen exchange between Oxy75P and the fully open oxygenator Oxy100P (ANOVA p > 0.38).

Mitotic outcomes and errors in fibrous environments

During mitosis, cells round up and utilize the interphase adhesion sites within the fibrous extracellular matrix (ECM) as guidance cues to orient the mitotic spindles. Here, using suspended ECM-mimicking nanofiber networks, we explore mitotic outcomes and error distribution for various interphase cell shapes. Elongated cells attached to single fibers through two focal adhesion clusters (FACs) at their extremities result in perfect spherical mitotic cell bodies that undergo significant 3-dimensional (3D) displacement while being held by retraction fibers (RFs). Increasing the number of parallel fibers increases FACs and retraction fiber-driven stability, leading to reduced 3D cell body movement, metaphase plate rotations, increased interkinetochore distances, and significantly faster division times. Interestingly, interphase kite shapes on a crosshatch pattern of four fibers undergo mitosis resembling single-fiber outcomes due to rounded bodies being primarily held in position by RFs from two perpendicular suspended fibers. We develop a cortex-astral microtubule analytical model to capture the retraction fiber dependence of the metaphase plate rotations. We observe that reduced orientational stability, on single fibers, results in increased monopolar mitotic defects, while multipolar defects become dominant as the number of adhered fibers increases. We use a stochastic Monte Carlo simulation of centrosome, chromosome, and membrane interactions to explain the relationship between the observed propensity of monopolar and multipolar defects and the geometry of RFs. Overall, we establish that while bipolar mitosis is robust in fibrous environments, the nature of division errors in fibrous microenvironments is governed by interphase cell shapes and adhesion geometries.

Influence of the number of layers on the strength of beech laminated elements in the three-point flexural test,

A chair is a piece of furniture whose elements are loaded with relatively high forces. The strength of these elements is vital for the safety of using this type of furniture. The research aims to test the chair material system made of beech wood. The authors analyzed laminated elements with 9, 11, and 13 layers of veneers. The veneers were 1.23 mm thick, with perpendicular fiber directions in adjacent layers, and bonded with 220 g/m2 of PVAc adhesive. The moisture content of the elements was 6 ± 1%. A three-point bending flexural test was performed to determine the stress-strain response of the tested three variants. A complementary numerical analysis allowed a more precise comparison of the three analyzed laminated elements variants. It was confirmed that all variants exceed the desired minimal values in chair support design. Moreover, the average strength values for tested laminated elements, differing in the number of veneers, were sufficient even with a reduced number of veneer layers. The experiments and numerical analysis results confirmed the usability of the three tested types of beech laminated elements to be used as highly loaded chair elements.

Mesoscale Numerical Analysis of Fiber-Reinforced Sand with Different Fiber Orientations Subjected to Seepage-Induced Erosion Based on DEM

This paper focuses on the effect of fiber orientation on the resistance of seepage-induced erosion in fiber-reinforced sand. To clarify the discrepancy and mechanism of different-oriented fibers improving the resistance of the sand matrix, a series of DEM-Darcy coupling simulations were conducted. The microscopic parameters of fiber-reinforced sand were confirmed by the rigorous calibration procedure. The fibers perpendicular to the seepage direction were found to increase the difficulty of moving fluid through the specimen and significantly reduce the erosion rate of the specimen. These macroscopic behaviors acquired corresponding explanations at the mesoscopic scale, including the evolution of fiber-sand contact orientation, coordination number, average normal contact force, tensile force, and energy dissipation. According to the simulation results, it is found that the highest proportion of tensile force in perpendicular fibers can reach 80%, while the parallel fibers are only 40%, which indicates that the perpendicular fibers have a significant netting effect. The mesoscopic behaviors reasonably revealed the role of the fibers with different orientations on the sand matrix during the seepage. This study is beneficial for further understanding the mechanical behaviors of fiber-reinforced sand under seepage-induced erosion in safety engineering.

Polarization-insensitive refractive index measurement using cascaded perpendicular tilted fiber Bragg gratings

This paper presents a possibility to improve the reliability of the measurement of the liquid solution refractive index using tilted fiber Bragg gratings (TFBGs) under various inputs of light polarization angle. The application of a specialized setup of cascaded TFBGs provides a great improvement in the stability of cladding resonances under various light polarization. In the present paper, the analysis of the amplitude of the cut-off cladding mode shows that the dependence of this parameter in the case of the proposed structure is reduced by 96.101% compared with a single TFBG with the same internal tilt angle of 7° and a depth of periodic refractive index perturbations. Stabilization of the spectra under various polarizations of inputted light could be observed in the case of all cladding modes, which could be used to improve the surrounding refractive index (SRI) measurement over a wider range.

Thermal Aspects in Edge Trimming of Bio-Filled GFRP: Influence of Fiber Orientation and Silica Sand Filler in Heat Generation.

The present work aims to determine the influence of Glass Fiber-Reinforced Polymer (GFRP) laminating configuration in heat generation during the dry edge trimming process. Temperature measurement experiments were conducted on pure epoxy matrix, 15% unidirectional glass fiber reinforced epoxy, and 28% silica sand-filled GFRP specimens through eight type-K thermocouples evenly distributed along the trim plans and connected to a data acquisition system. Infrared thermographic measurements were also conducted to investigate the tool temperature evolution while processing. It was found that perpendicular fiber edge milling induces a sharp increase with peak temperature measurements reaching 119 °C, while machining parallel to fiber leads to a maximum temperature history of 41 °C, which is very close to that obtained from the pure epoxy test. It was also found that the addition of silica sand grains in the GFRP matrix reduces both tool and specimen temperature magnitudes up to 67% for 90° plies and 14% for 0° plies compared to silica sand-free composite initial values. The heat partition was calculated from the measured (electric) and estimated energies for the tool, the workpiece, and chips, respectively. It appears from predictions that the addition of silica sand grains increases the heat conductivity of the GFRP materials (with rates of 20% for 0° fiber orientation and 10% for 90° fiber direction), while it reduces that conducted to the milling tool. Scanning Electron Microscopy (SEM) inspections helped detect the dominating machining defects relative to each GFRP configuration and explained the heat generation and dissipation effects in light of peak temperature measurements.

Static and dynamic BOLD fMRI components along white matter fibre tracts and their dependence on the orientation of the local diffusion tensor axis relative to the B0-field

Recent studies have reported functional MRI (fMRI) activation within cerebral white matter (WM) using blood-oxygenation-level-dependent (BOLD) contrast. Many blood vessels in WM run parallel to the fibre bundles, and other studies observed dependence of susceptibility contrast-based measures of blood volume on the local orientation of the fibre bundles relative to the magnetic field or B0 axis. Motivated by this, we characterized the dependence of gradient-echo BOLD fMRI on fibre orientation (estimated by the local diffusion tensor) relative to the B0 axis to test whether the alignment between bundles and vessels imparts an orientation dependence on resting-state BOLD fluctuations in the WM. We found that the baseline signal level of the T2*-weighted data is 11% higher in voxels containing fibres parallel to B0 than those containing perpendicular fibres, consistent with a static influence of either fibre or vessel orientation on local T2* values. We also found that BOLD fluctuations in most bundles exhibit orientation effects expected from oxygenation changes, with larger amplitudes from voxels containing perpendicular fibres. Different magnitudes of this orientation effect were observed across the major WM bundles, with inferior fasciculus, corpus callosum and optic radiation exhibiting 14–19% higher fluctuations in voxels containing perpendicular compared to parallel fibres.

Investigation on scratching force and material removal mechanism of 3D SiCf/C–SiC composites during single grain scratching

As one of the novel fiber-reinforced ceramic matrix composites, SiCf/C-SiC composites are difficult to machine materials and the material removal mechanism is not completely clear yet. Single grain scratching tests with gradual depth have been carried out to analyze the influence of fiber orientation and woven structure on the material removal mechanism and scratching force in three typical scratched surfaces defined by the fiber orientation. Results indicate that the scratching force waveform is affected by the weaving method, fibers orientation, and porosity distribution of the scratched area, resulting in periodic fluctuations. Diamond indenter causes greater damage to the surface of SiCf/C-SiC composites when scratching along transverse fibers, while leaving narrow but deep grooves on the surface when scratching along perpendicular fibers. The dominant mode of material removal of SiCf/C-SiC composites is brittle fracture, and the damage features mainly include direct fiber breakage, matrix fragmentation, fiber pullout, fiber outcropping.

Cavitation Plays a Vital Role in Stone Dusting During Short Pulse Holmium:YAG Laser Lithotripsy.

Objective: To investigate the mechanism of stone dusting in Holmium (Ho): YAG laser lithotripsy (LL). Materials and Methods: Cylindrical BegoStone samples (6 × 6 mm, H × D) were treated in water using a clinical Ho:YAG laser lithotripter in dusting mode (0.2-0.4 J with 70-78 μs in pulse duration, 20 Hz) at various fiber tip to stone standoff distances (SD = 0, 0.5, and 1 mm). Stone damage craters were quantified by optical coherence tomography and bubble dynamics were captured by high-speed video imaging. To differentiate the contribution of cavitation vs thermal ablation to stone damage, three additional experiments were performed. First, presoaked wet stones were treated in air to assess stone damage without cavitation. Second, the laser fiber was advanced at various offset distances (OSD = 0.25, 1, 2, 3, and 10 mm) from the tip of a flexible ureteroscope to alter the dynamics of bubble collapse. Third, stones were treated with parallel fiber to minimize photothermal damage while isolating the contribution of cavitation to stone damage. Results: Treatment in water resulted in 2.5- to 90-fold increase in stone damage compared with those produced in air where thermal ablation dominates. With the fiber tip placed at OSD = 0.25 mm, the collapse of the bubble was distracted away from the stone surface by the ureteroscope tip, leading to significantly reduced stone damage compared with treatment without the scope or with scope at large OSD of 3-10 mm. The average crater volume produced by parallel fiber orientation at 0.2 J after 100 pulses, where cavitation is the dominant mechanism of stone damage, was comparable with those produced by using perpendicular fiber orientation within SD = 0.25-1 mm. Conclusion: Cavitation plays a dominant role over photothermal ablation in stone dusting during short pulse Ho:YAG LL when 10 or more pulses are delivered to the same location.

Experimental study and simulation of non-crimp 3D orthogonal composite shafts during torsional load

Non-crimp 3D orthogonal fabrics are high-tech textiles with three sets of orthogonal yarns. 3D composites reinforced by this fabric have a high performance and wide usages due to their structure. This study attempted to investigate the torsional behavior of Glass/epoxy composite rods reinforced by 3D fabrics experimentally and numerically. Accordingly, three different 3D weaves, including low-density and high-density non-crimp 3D orthogonal, and braid-pultruded fabrics were tested by a torsion tester machine. The results showed that non-crimp 3D orthogonal composites, especially those with a higher density, had better torsional properties than the others, due to the square cross-section and perpendicular fiber involvement in all directions. Optimal torsional properties were obtained for the high-density non-crimp 3D orthogonal composite with the lower void content. Also, a python code was developed to simulate the torsional behavior of the rod composite in macro-scale based on the geometry of the unit cell and the mechanical constants obtained from the meso-scale.

Cylindrical metal liner implosion at extremes of pressure and material velocity on an intense pulsed power facility-FP-2.

Highly precise and controllable liner implosions driven by a pulsed power facility have extensive applications in exploration of advanced hydrodynamics at the extremes of pressure and material velocity. In this paper, we describe a new pulsed power facility developed in China named FP-2 (a series of facilities for Fluid Physics investigations-the second generation) for liner implosions. Benefiting from the reliable and stable operation of 48 rail gap switches, the FP-2 facility can steadily transmit a current of 10.5 MA to a dummy load of 10 nH in the case of a charging voltage of ±40kV. The first quarter cycle is 5.5 µs, and the percentage shot-to-shot deviation of the current history is less than 1%. When the aluminum liners of 60mm in height and 0.6mm in thickness are adopted, the maximum velocity of 4.5 and 7.5 km/s has been achieved with the liner diameter of 90 and 60mm, respectively, at the diameter of 10mm. Experimental results show that the percentage shot-to-shot deviation of the liner velocity history is less than 1%. As impact on the target, the maximum of the impact time deviation measured from four perpendicular fiber pins is less than 20ns. Due to the modular design of FP-2, it is convenient for a future upgrade. The confirmation of high-quality implosion on FP-2, such as high repeatability, high reliability, and high symmetry, makes it a bright prospect to explore the advanced hydrodynamic problems at extremes of pressure and material velocity in the future.