Peroxymonosulfate System Research Articles

Magnetic MgFeO@BC Derived from Rice Husk as Peroxymonosulfate Activator for Sulfamethoxazole Degradation: Performance and Reaction Mechanism.

Heterogeneous Mg-Fe oxide/biochar (MgFeO@BC) nanocomposites were synthesized by a co-precipitation method and used as biochar-based catalysts to activate peroxymonosulfate (PMS) for sulfamethoxazole (SMX) removal. The optimal conditions for SMX degradation were examined as follows: pH 7.0, MgFeO@BC of 0.4 g/L, PMS concentration of 0.6 mM and SMX concentration of 10.0 mg/L at 25 ℃. In the MgFeO@BC/PMS system, the removal efficiency of SMX was 99.0% in water within 40 min under optimal conditions. In the MgFeO@BC/PMS system, the removal efficiencies of tetracycline (TC), cephalexin (CEX), ciprofloxacin (CIP), 4-chloro-3-methyl phenol (CMP) and SMX within 40 min are 95.3%, 98.4%, 98.2%, 97.5% and 99.0%, respectively. The radical quenching experiments and electron spin resonance (ESR) analysis suggested that both non-radical pathway and radical pathway advanced SMX degradation. SMX was oxidized by sulfate radicals (SO4•-), hydroxyl radicals (•OH) and singlet oxygen (1O2), and SO4•- acted as the main active species. MgFeO@BC exhibits a higher current density, and therefore, a higher electron migration rate and redox capacity. Due to the large number of available binding sites on the surface of MgFeO@BC and the low amount of ion leaching during the catalytic reaction, the system has good anti-interference ability and stability. Finally, the intermediates of SMX were detected.

Decoration of marigold flower-like CoMo LDH on reinforced cow manure-derived biochar as an effective peroxymonosulfate activator for degradation of Bisphenol A in water

Marigold flower-like CoMo layered double hydroxide (LDH) was decorated on biochar derived from cow manure (CoMo@BC) to act as an efficient activator for peroxymonosulfate (PMS), enabling the degradation of Bisphenol A (BPA) in water. The CoMo@BC/PMS system can eliminate up to 98% of BPA at a concentration of 0.044mM within 15min. High efficacy is sustained in the pH range of 5 to 9, underscoring the robustness and adaptability of the system. Furthermore, the catalyst exhibits excellent stability, retaining activity over five consecutive cycles. Versatility is highlighted by the capability to degrade over 88% of various organic pollutants, indicating broad-spectrum applicability in water treatment. A comprehensive mechanistic study has elucidated three distinct degradation pathways and identified six intermediates of BPA, providing valuable insights into the catalytic process. Overall, the research underscores the potential of CoMo@BC as a highly effective catalyst for advanced water treatment applications through PMS activation. Significant efficacy in eliminating organic pollutants suggests great promise for enhancing the sustainability and efficiency of water purification technologies.

Efficient degradation of Enrofloxacin with novel magnetic MnFe2O4/NiS2 composite as an activator of peroxymonosulfate

The development of highly active and recoverable heterogeneous catalysts for peroxymonosulfate (PMS) activation to remove the persistent presence of antibiotics in aquatic environments, such as Enrofloxacin (ENR), remains a significant challenge. Here, we introduce a pioneering magnetic nanocomposite catalyst, MnFe2O4-NiS2, synthesized via a two-step hydrothermal process, which activates PMS to efficiently degrade ENR. The optimized 0.25MnFe2O4-NiS2/PMS system reached an ENR removal efficiency of 89.9 % within 90 min, outperforming both NiS2/PMS and MnFe2O4/PMS by 5.6 and 2.5 times, respectively. Quenching experiments and electron spin response analysis confirmed SO4•- and •O2– as the primary reactive oxygen species. The enhanced mediated electron transfer capability of the 0.25MnFe2O4-NiS2 nanocomposite improved the redox cycling of Ni (Ⅱ), Mn (Ⅱ) and Fe (Ⅲ) on its surface, as verified by Density Functional Theory calculations. Furthermore, the activation of surface PMS complexes (PMS*) played a crucial role in ENR degradation. The proposed degradation pathways of ENR were confirmed, and toxicity analysis indicated a decrease in intermediate toxicity with the 0.25MnFe2O4-NiS2/PMS system. This study presents an innovative magnetically recoverable, multifunctional catalyst with easy reusability for potential applications in the degradation of organic pollutants.

Oxidative degradation of anionic dyes in wastewater by magnetic lignin micro-nano spheres catalyzed peroxymonosulfate

Lignin has gained significant attention in wastewater treatment due to its abundant resources and good adsorbability. In this work, magnetic lignin micro-nano spheres (Fe3O4@SiO2-LNS) was prepared using alkali lignin as the raw material, and was used as the adsorbent and catalyst to activate peroxymonosulfate (PMS) to build an inhomogeneous catalytic oxidation system (Fe3O4@SiO2-LNS/PMS). The system was then used to remove the stubborn acid blue 9 (AB9) dye in wastewater, and the effects of pH, catalyst dosage, PMS dosage of the system on the removal percentage of AB9 dye and the corresponding degradation mechanism were explored. The results showed that Fe3O4@SiO2-LNS/PMS system had good removal efficiency for AB9 in wastewater, and AB9 dye was completely oxidized and finally degraded into CO2 and H2O. The maximum removal percentage of AB9 was observed when the pH and temperature of the system were 6.0 and 313 K, and the removal percentage of AB9 achieved 100 % when the optimal dosage of Fe3O4@SiO2-LNS and PMS were 3.44 g/L and 53.15 mM, respectively. In addition, Fe3O4@SiO2-LNS had good stability and reusability. This work provides a promising approach for abatement of dyeing wastewater pollution and a new direction for high-value utilization of alkali lignin.

The synergistic effect of Co atomic clusters and single atoms facilitates the fenton-like reaction on A- and R-TiO2

The regulation of single atom (SA) sites is crucial for the promotion of advanced oxidation processes (AOPs). Here A- and R-TiO2 with Co mixed sites (clusters and single atoms, CS) were prepared to degrade sulfamethoxazole (SMX) by activating peroxymonosulfate (PMS). Co CS/A-TiO2+PMS system can completely remove SMX within 14 min under secondary effluent and dark conditions, and its rate constant (0.4926 min-1) was 4.4, 3.2 and 2.5 times higher than that of Co SA/R-TiO2, Co SA/A-TiO2 and Co CS/R-TiO2 systems, respectively. Experiments and calculations verified that the electron configuration of Co SA was optimized by Co clusters, facilitating the adsorption, conversion and desorption of PMS by Co SA, leading to the enhancement of Fenton-like activity. Co CS/A-TiO2 catalytic sponges exhibited exceptional degradation performance in microreactor treatment experiment. This work reveals the synergistic effect between SA and clusters at atomic level and provides an all-purpose strategy (catalytic sponge) for the recovery of non-magnetic catalysts in wastewater treatment.

Cobalt/iron bimetallic oxide coated with graphitized nitrogen-doped carbon (Fe2O3-CoO@NC) derived from cobalt/iron solid complex as peroxymonosulfate (PMS) activator for efficient bensulfuron-methyl degradation

Cobalt/iron bimetallic oxide coated with graphitized nitrogen-doped carbon (Fe2O3-CoO@NC) was synthesized by convenient solid phase coordination combined with calcination method to activate PMS for the degradation of BSM. A series of Co/Fe bimetallic oxides with different metal ratios were designed and prepared to select the most efficient catalyst and Fe2O3-CoO@NC(Co:Fe = 1:1) demonstrated the highest catalytic activity and the lowest ions leaching. The reasons for high catalytic activity of Fe2O3-CoO@NC(Co:Fe = 1:1) were evaluated by a range of characterization techniques and the results showed it stemmed from higher mental content and larger current density. Complete (100%) degradation of 10 g L−1 BSM was achieved within 10 min under the conditions of 0.05 g L−1 catalyst and 0.3 mmol/L PMS dosage at 25 °C. Moreover, Fe2O3-CoO@NC(Co:Fe = 1:1) showed more excellent catalytic activity and lower ions leaching than Fe2O3, CoO and Fe2O3-CoO, indicating superior bimetallic synergy and carbon encapsulation effect. Furtherly, radical experiments and XPS analysis revealed the main active species and catalytic mechanism of the Fe2O3-CoO@NC/PMS system, respectively. Finally, the degradation pathway of BSM by Fe2O3-CoO@NC/PMS system was deduced by LC-TOF-MS. This paper is aimed to provide a new insight into the convenient preparation method for the construction of catalysts which could reach efficient removal of complex organic pollutants.

Ornidazole degradation based on peroxymonosulfate activation induced by oxygen vacancies (OV)-enriched Cu-Co-TiO2: Coexistence of free-radical and non-radical pathways

Employing transition-metal catalysts in peroxymonosulfate (PMS) activation reactions to facilitate combined free-radical and non-radical interactions is regarded as a proficient approach for decomposing organic contaminants. However, the creation of active catalysts faces significant challenges due to low activation efficiency, inadequate action sites, and instability of current activation materials. Here, we successfully prepared bimetallic Cu and Co co-doped TiO2 (Cu-Co-TiO2) catalyst using the sol-gel technique. Excellent ornidazole (ONZ) removal efficiency (0.628 min−1) was demonstrated by the Cu-Co-TiO2/PMS system, which was applicable across a broad pH range (4−10) and unaffected by different water matrices. Moreover, the coexistence of free-radical (SO4•-, •OH and O2•−) and non-radical (1O2) routes in the Cu-Co-TiO2/PMS system, where SO4•- and 1O2 are the predominant active substances, was confirmed by quenching experiments and electron paramagnetic resonance (EPR) study. The synergistic impact of Cu/Co bimetal may hasten the redox cycles of Cu+/Cu2+ and Co2+/Co3+, causing plenty of oxygen vacancies (OV) and improving PMS activation efficiency. The quantitative structure-activity relationship (QSAR) examination of the intermediates showed a decrease in toxicity, and the potential pathways of ONZ degradation were illustrated using Liquid Chromatography Mass Spectrometry (LC-MS) technology. This work not only demonstrated the effectiveness and stability of Cu-Co-TiO2 as a PMS activator, but it also offered fresh information on how to remove organic pollutants from wastewater by using PMS activation via the radical and non-radical oxidation pathway.

Activation of peroxomonosulfate by manganese-containing non-homogeneous catalysts prepared via a soft template calcination strategy for efficient degradation of carbamazepine

Manganese (Mn)-containing inhomogeneous catalysts have demonstrated potential to activate peroxymonosulfate (PMS), but may be constrained by low efficiency and poor resistance to environmental disturbances. According to the soft template calcination strategy, g-C3N4 with Mn doping was synthesized to improve PMS activation through an effective Mn(II)/Mn(III)/Mn(IV) cycle. The constructed Mn25@CN/PMS system achieved complete and rapid removal of carbamazepine (CBZ) at 0.3 g/L catalyst and 2 mM PMS. Its corresponding rate constant of pseudo-first-order was 0.3424 min−1, and it was 3424 and 16.15 times higher than that of pure g-C3N4/PMS system and CN/PMS system, respectively. More strikingly, the catalysts exhibited excellent resistance to environmental impacts, with CBZ removal rates exceeding 95% under the influence of different anions, cations, aqueous pH values, and humic acid (HA) concentrations. Subsequently, it was proposed a reliable catalytic mechanism for CBZ removal and PMS activation derived from electron paramagnetic resonance (EPR) tests and quenching experiments. The O2·- and 1O2 played a major role in the CBZ removal process. This research provides a perspective soft template strategy for PMS activation using highly efficient catalysts with high resistance to environmental impacts, which provides new ideas to alleviate environmental issues.

Enhanced Ornidazole Degradation via Peroxymonosulfate Activation Using Nano CoFe2O4‐Decorated Halloysite Nanotubes: A High‐Efficiency and Stable Catalyst Approach

AbstractThis study proposes a novel, cost‐effective nano CoFe2O4‐decorated halloysite nanotubes (CoFe2O4/HNT) catalyst, which effectively degrades the antibiotic ornidazole (ONZ) through peroxymonosulfate (PMS) activation. By using a simple and economical preparation method, ultra‐low amounts of CoFe2O4 are uniformly loaded onto HNTs, significantly improving the activity and stability of the catalyst. The experimental results show that the CoFe2O4/HNT+PMS system can almost completely degrade ONZ within 1 h, with good pH adaptability and resistance to anion interference. The simple synthesis process and low cost of CoFe2O4/HNT make it highly practical for large‐scale applications. Mechanism studies have shown that the synergistic effect between Co and Fe greatly improves the activation efficiency of PMS, generating reactive oxygen species (such as 1O2) that play a key role in ONZ degradation. This work not only elucidates the activation mechanism, but also provides insightful information for advanced oxidation processes (AOP). The results indicate the practicality and importance of CoFe2O4/HNT catalyst in treating harmful pollutants in water, supporting effective and sustainable water purification technologies. In addition, the study emphasizes the elasticity and adaptability of this innovative catalyst system in managing various pollutants, indicating its broad potential for environmental applications.

WS2-Assisted Electrochemical Activation of Peroxymonosulfate for Eliminating Organic Pollutant in Water

Advanced oxidation process based on heterogeneous activation of peroxymonosulfate (PMS) has received significant attention in wastewater remediation. Herein, a facile and effective electrochemical method was introduced in a tungsten sulfide (WS2)-activated PMS process for the removal of a typical azo dye Acid Orange 7 (AO7) in aqueous solution. It was found that the electrochemical activation could remarkably promote the removal of organic pollutants by coupling with WS2/PMS system. The elimination of AO7 in the electro-assisted WS2-activated PMS (E/WS2/PMS) system achieved 95.8% of AO7 removal in 30 min, with the optimal conditions of 1.0 g/L WS2, 1.0 mM PMS, current density of 1.0 mA/cm2 and initial pH of 6.5. Based on quenching experiments and EPR techniques, mechanistic studies confirmed that hydroxyl radical (•OH) and singlet oxygen (1O2) are the primary reactive oxygen species for the oxidation of pollutants. In addition, the influences of pH, WS2 dosage, PMS concentration, current density, common anions and humic acid on the AO7 removal are also investigated in detail. Furthermore, the system exhibited resistance to aqueous matrices, verifying the accepted applicability in real water (i.e., Yangtze River water and Shahu Lake water). In summary, this study demonstrates a green system for the effective removal of contaminants in water, holding significant implications for practical application.

Unveiling the heterojunction of Fe3O4@MXene nanocatalyst for ultrafast degradation of antibiotics via non-radical pathway

The transfer of advanced oxidation processes (AOPs) to real-world applications faces several technology challenges involving oxidation performance, catalyst cost, poor reactive oxygen species (ROS) yield, and long-term stability. This work aims to develop a reactive, efficient, and stable MXene-based nanocatalyst, namely Fe3O4@Ti3C2Tx, for ultrafast removal of the selected sulfonamide antibiotics. As revealed by extensive nanocatalyst characterization, the MXene surface not only anchors Fe/Fe3O4 nanoparticles (NPs) but also prevents NP agglomeration. Notably, the conductive interface between MXene and Fe3O4 promotes the Fe(II)/Fe(III) redox cycle and accelerates peroxymonosulfate (PMS) activation. The Fe3O4@Ti3C2Tx demonstrates excellent catalytic activity by achieving complete sulfamethoxazole (SMX) degradation within 6 min and maintained its catalytic activity after 5 continuous cycles. In the Fe3O4@Ti3C2Tx/PMS system, multiple ROS (e.g., •OH, SO4•-, O2•-) are involved but 1O2 was found to be the primary ROS for SMX degradation. The presence of co-exiting inorganic impurities and pH changes may hinder SMX degradation. Finally, elucidating possible degradation pathways of SMX would greatly aid in treating antibiotic-containing wastewater.

Efficient Adsorption and Degradation of Tetracycline Hydrochloride Using Metal-Organic Framework-Derived Cobalt-Based Catalysts and Mechanism Insight.

High-performance Co-based catalysts were derived by pyrolysis using synthesized MOFs as self-sacrificial templates. Various catalytic systems were constructed by peroxymonosulfate (PMS) to degrade tetracycline hydrochloride (TC). Adsorption-degradation efficiencies, cycle performance, dynamics, and the adsorption catalytic mechanism of various catalytic systems for TC were studied. The effects of different synthetic solvents, pyrolysis temperatures, and single/bimetallic element compositions on degradation efficiency were innovatively compared. The optimal catalyst and PMS dosage for the experiment were determined to be 10 mg and 0.1 mL, respectively. The results indicated that all catalytic systems could efficiently degrade TC and have a high acid-base resistance. The catalyst activity was significantly influenced by the pyrolysis temperature. The optimum pyrolysis temperatures for Zn@Co-N-C-T, CH3OH@Co-N-C-T, and H2O@Co-N-C-T were 1000, 900 and 900 °C, respectively. More abundant pore structures and active sites were generated in Zn@Co-N-C-1000, exhibiting an excellent TC degradation efficiency and adsorption capacity, achieving 94.73% and 167.564 mg/g, respectively. Meanwhile, the total organic carbon (TOC) of TC (50 mL, 50 mg/L) achieved a removal rate (TOC/TOC0) of 50.28%. Zn@Co-N-C-1000/PMS maintained over 83.27% TC degradation after five cycles. The adsorption mechanism of the catalyst for TC was investigated through the analysis of adsorption kinetics and isotherm models. The quenching test and EPR results indicated that TC was primarily degraded through the nonradical pathway. The efficient degradation of TC is attributed to the rapid electron transfer processes occurring at the two-phase interface and the redox cycling of Co0/Co2+/Co3+. Finally, LC-MS was used to analyze the intermediate products of TC degradation in the Zn@Co-N-C-1000/PMS system, and two degradation pathways were proposed.

Co-N3 site activated peroxymonosulfate for rapid degradation of ciprofloxacin: Synergistic effect of free radicals and nonfree radicals

Nitrogen-doped metal-organic framework (MOFs)-derived carbon materials (denoted as Co-MOF-74@N-T-x) were successfully fabricated by calcinating Co-MOF-74, utilizing the green precursor of melamine. Among these materials, Co-MOF-74@N-500-2 demonstrated superior catalytic performance in activating peroxymonosulfate (PMS), achieving over 95 % degradation of ciprofloxacin (CIP) within 15 min, with a rate constant that was 1.25 times greater than that of Co-MOF-74-500. The primary active species identified in this study were sulfate radicals (SO4•−) and singlet oxygen (1O2), with the latter playing an important role in the degradation of CIP in the Co-MOF-74@N-500-2/PMS system. Theoretical calculations confirmed that the enhanced catalytic activity primarily stemmed from the Co-N3 configuration, which was more effective in activating PMS than the other configurations were. Co-MOF-74@N-500-2/PMS showed excellent performance in oxidizing CIP across a broad pH range (3.0–9.0) and demonstrated stability over five cycles, along with impressive degradation performance capabilities for a wide range of pollutants including metronidazole (MNZ), oxytetracycline (OTC), nitrofurantoin (FNT), methylene blue (MB), and acid orange (OG). This study presents a viable strategy for developing efficient and durable catalytic systems aimed at degrading organic pollutants via PMS.

Sludge carbon quantum dots-activated peroxymonosulfate oxidation for sludge conditioning

Large amounts of waste activated sludge (WAS) are produced from biological treatment processes in wastewater treatment plants, and its effective disposal and reutilization are considered to be inevitable challenges in the world. In this work, carbon quantum dots derived from WAS (SCQDs) were successfully synthesized via hydrothermal method, which had a significant photoluminescence effect, excellent water solubility, and graphite structures with main elements of C, N, and O. Subsequently, its potential for peroxymonosulfate (PMS) activation under visible light for WAS conditioning was investigated. The results showed that SCQDs-activated PMS (SCQDs-PMS) system could effectively improve sludge dewaterability. Under experimental conditions, capillary suction time reduction and water content of sludge cake after conditioning were 81.2% and 72.6%, respectively. Reactive oxygen species including SO4·-, ·OH, and 1O2 produced in SCQDs-PMS system could effectively degrade extracellular polymeric substances (EPS) (especially tyrosine-like and tryptophan-like substances in tightly bound-EPS), inactivate microbial cells, and destruct α-helix structure of protein molecule, which resulted in the desirable release of EPS-bound water, consequently improving sludge dewaterability. This result was well supported by the variations in the transverse relaxation time of protons at low field nuclear magnetic resonance. Thus, this work explored a potential pathway of reutilizing sludge and a new activator for PMS activation. However, it should be noticeable that this work was the first attempt using SCQDs-PMS system for sludge conditioning, the future studies about system optimization and its wider application scenarios should be further investigated.

Efficient Degradation of Ofloxacin by Magnetic CuFe2O4 Coupled PMS System: Optimization, Degradation Pathways and Toxicity Evaluation.

Magnetic CuFe2O4 was prepared with the modified sol-gel method and used for enhanced peroxymonosulfate (PMS) activation and ofloxacin (OFL) degradation. The OFL could almost degrade within 30 min at a catalyst dosage of 0.66 g/L, PMS concentration of 0.38 mM, and initial pH of 6.53 without adjustment, using response surface methodology (RSM) with Box-Behnken design (BBD). In the CuFe2O4/PMS system, the coexisting substances, including CO32-, NO3-, SO42-, Cl- and humic acid, have little effect on the OFL degradation. The system also performs well in actual water, such as tap water and surface water (Mei Lake), indicating the excellent anti-interference ability of the system. The cyclic transformation between Cu(II)/Cu(I) and Fe(III)/Fe(II) triggers the generation of active radicals including SO4•-, •OH, •O2- and 1O2. The OFL degradation pathway, mainly involving the dehydrogenation, deamination, hydroxylation, decarboxylation and carboxylation processes, was proposed using mass spectroscopy. Moreover, the toxicity assessment indicated that the end intermediates are environmentally friendly. This study is about how the CuFe2O4/PMS system performs well in PMS activation for refractory organic matter removal in wastewater.

Unraveling the Fundamentals of Axial Coordination FeN4+1 Sites Regulating the Peroxymonosulfate Activation for Fenton-Like Activity.

Precise modulation of the axial coordination microenvironment in single-atom catalysts (SACs) to enhance peroxymonosulfate (PMS) activation represents a promising yet underexplored approach. This study introduces a pyrolysis-free strategy to fabricate SACs with well-defined axial-FeN4+1 coordination structures. By incorporating additional out-of-plane axial nitrogen into well-defined FeN4 active sites within a planar, fully conjugated polyphthalocyanine framework, FeN4+1 configurations are developed that significantly enhance PMS activation. The axial-FeN4+1 catalyst excelled in activating PMS, with a high bisphenol A (BPA) degradation rate of 2.256 min-1, surpassing planar-FeN4/PMS systems by 6.8 times. Theoretical calculations revealed that the axial coordination between N and the Fe sites forms an optimized axial FeN4+1 structure, disrupting the electron distribution symmetry of Fe and optimizing the electron distribution of the Fe 3d orbital (increasing the d-band center from -1.231 to -0.432eV). Consequently, this led to an enhanced perpendicular adsorption energy of PMS from -1.79 to -1.82eV and reduced energy barriers for the formation of the key reaction intermediate (O*) that generates 1O2. This study provides new insights into PMS activation through the axial coordinated engineering of well-defined SACs in water purification processes.

Enhanced activation of peroxymonosulfate by nanomagnetic CoFe2O4-CeO2/g-C3N4 composites as a heterogeneous catalyst for metronidazole degradation

Antibiotic-induced catastrophic pollution has the potential to migrate over vast distances through water, thereby posing a detrimental effect on both humans and the environment. The construction of a highly robust catalyst to activate peroxymonosulfate (PMS) has become a fascinating approach for treating such types of wastewaters. In this study, we have developed CoFe2O4-CeO2/CN catalysts using an impregnation-hydrothermal and ultrasonication method to efficiently degrade metronidazole (MNZ). The synthesized catalyst materials were analyzed through multiple characterization techniques in order to correlate the material properties and the degradation performance. The degradation trials exhibited that MNZ underwent complete degradation within 40 min in the CoFe2O4-CeO2/CN-2/PMS system, with a rate constant of 0.1354 min−1, nearly 5.29 times faster than the CoFe2O4-CeO2/PMS (0.0235 min−1) under optimal conditions ([catalyst] = 0.5 g/L, [PMS] = 0.5 mM, [MNZ] = 20 mg/L, pH = 6.72). The increased abatement of MNZ in CoFe2O4-CeO2/CN-2/PMS system could be attributed to the higher surface area of the CoFe2O4-CeO2/CN-2 (75.96 m2/g) catalyst in comparison to the CoFe2O4-CeO2 (53.98 m2/g), which enhances the catalytically active sites and improves the PMS activation reaction. Besides, the impact of several operational variables and influencing anions on MNZ degradation was researched as well. The generation of free radicals was confirmed by radical scavenging analysis and authenticated using electron paramagnetic resonance analysis. The mechanistic analysis established that the activation of PMS was initiated by the transformations of Co3+/Co2+, Fe3+/Fe2+, and Ce4+/Ce3+. Briefly, this research provides valuable perspective for future research regarding heterogeneous catalysis leveraging PMS activation to alleviate toxic contaminants.

CoFe2O4/carbon nitride Z-scheme heterojunction photocatalytic PMS activation for efficient tetracycline degradation: Accelerated electron transfer

The escalating consumption of antibiotics and their subsequent discharge into the water supply is a matter of significant concern. This study presents an innovative visible light (VL) activated peroxymonosulfate (PMS) system for efficient degradation of the targeted antibiotic tetracycline (TC). CoFe2O4/carbon nitride (CFO/CN) Z-scheme heterojunctions were designed and synthesized through a simple co-precipitation and calcination strategy. Surface and analytical techniques were employed to comprehensively characterize the prepared CFO/CN, demonstrating its enhanced efficiency in separating photoinduced charge carriers. CFO/CN exhibited a 27-fold enhancement in TC degradation rate constants with PMS under VL. The effects of various factors including catalyst dosage, PMS concentration, initial pH, and content of CFO on TC degradation efficiency were investigated. Reactive species quenching and EPR measurements revealed the main contribution of superoxide radicals (•O2−) made to TC degradation. TC degradation pathways were proposed based on oxidized product analysis. The assessment of acute toxicity demonstrated the reduced toxicity of the formed intermediates. A plausible mechanism for TC degradation over CFO/CN-PMS-VL was discussed. This work provides a comprehensive guide for heterojunction photocatalytic activation of PMS for efficient micropollutant degradation.

An Anchored Fe-Cu LDH onto a Polyvinylidene Fluoride Membrane with Strong Peroxymonosulfate Activation-Induced Degradation of Methylene Blue and Self-Cleaning Property of Oil/Water Separation.

Developing a strong catalytic antifouling membrane to achieve efficient sewage purification has great potential for alleviating water crisis. In this work, we designed and prepared an Fe/Cu-layered double hydroxide (Fe-Cu LDH)-coated polyvinylidene fluoride (PVDF) composite membrane (PVDF/Fe-Cu LDHs) with strong antifouling and activating peroxymonosulfate (PMS) catalytic degradation performance through polydopamine-coordination anchoring and hydrothermal reaction. The results showed that abundant hydroxyl groups of the LDH surface endowed the superhydrophilicity (water contact angle <10°) and underwater superoleophobicity (underwater-oil contact angle >150°) of the membrane surface, which displayed outstanding resistance to crude oil adhesion. With assistance of the LDH surface-bound sulfate radical of the peroxymonosulfate system, the PVDF/Fe-Cu LDH membrane demonstrated robust catalytic degradation performance for the methylene blue (MB) in the dark; the degradation rate constant (k, min-1) reached 0.96. Meanwhile, facing the oily wastewater, the selective wettability and charge effect of LDH of the surface made the PVDF/Fe-Cu LDH membrane realize the separation for the various surfactant-free and surfactant-stabilized emulsions. Importantly, the PMS-activation catalytic produced the ROS (•SO4-,•OH, •O2-, and 1O2), which enhanced the regeneration of the fouled PVDF/Fe-Cu LDH membrane and obtained a high flux recovery ratio in the dark (94.7%) after 10 cycles of separation experiments. Hence, we believed that the PVDF/Fe-Cu LDH membrane can provide inspiration for the development and further practical application of antifouling membranes.

Novel red mud-based FeS2 composite used as an effective heterogeneous catalyst for the degradation of levofloxacin: Preparation, application and degradation mechanism

Red mud (RM), as industrial waste, was considered as the base material in this study. A heterogeneous catalyst of RM based-FeS2 (RM-FeS2) was prepared using a simple one-step calcination method. RM-FeS2, as an effective activator of peroxymonosulfate (PMS), was utilized in the levofloxacin (LVF) degradation progress. The effect of the preparation conditions on crystal structure and catalytic activity of RM-FeS2 was investigated. The systematic characterizations indicated that the surface area, electrical conductivity and the number of Fe(II) sites of RM were improved after compounding with FeS2. According to the investigation of catalytic performance of RM-FeS2, approximately 87% of LVF (10 mg/L) was degraded in 60 min with the reaction conditions: [RM-FeS2] = 0.2 g/L, [PMS] = 1 mmol/L and initial pH of 6.2. The RM-FeS2 possessed excellent stability and reusability. ·OH, SO4•−, 1O2 and Fe(Ⅳ) were the dominant active species in RM-FeS2/PMS system. Several possible degradation pathways of LVF were proposed. The toxicity of the treated LVF solution was effectively reduced in the RM-FeS2/PMS system. In a word, this study not only realized the resource utilization of RM, but also presented a novel perspective for the effective degradation of organic pollutants in wastewater.