Permeability Measurements Research Articles

Experimental Investigation of Internal Erosion of Gap-Graded Sands

Internal erosion often occurs in earthen water-retaining structures such as embankment dams, levees, or dikes, which are created by seepage flows through soil or other porous material where coarser and finer particles are mixed. This erosion process may be referred to as suffusion, resulting in the transportation of fine particles carried away from the soil structure by seepage. If internal erosion occurs, the strength of the soil will be changed, and gaps or cavities in the soil structure may be created, leading to the collapse of the soil, posing a risk of damage to earthen water-retaining structures. This research investigates internal erosion behaviour of gap-graded sands with various fine contents using a series of upward seepage tests. An in-house developed apparatus with a measurement of hydraulic gradient and permeability is used to investigate the initiation and progress of internal erosion.

High Frequency Permeability Measurements and Modeling of Magnetic Powder Cores Under DC Bias

High Frequency Permeability Measurements and Modeling of Magnetic Powder Cores Under DC Bias

Preparation and Characterization of Graphene and Carbon Nanotube Hybrid Polydimethylsiloxane Composites for Protective Coating Applications

In this work, the synergistic effect of graphene nanosheets (GNs), as well as multiwalled carbon nanotubes (MWCNTs), as reinforcing agents of polydimethylsiloxane (PDMS) was investigated, in order to explore the possibilities of designing composite materials, tailored for use in the field of coatings, which might be, in fact, a very interesting application. It was shown that the addition of GNs and MWCNTs in PDMS matrices significantly improves the thermal stability of the obtained nanocomposites, especially those reinforced exclusively with GNs. The tensile tests indicated that strength increased for all the examined composites. It was also observed that the Young’s moduli had an increasing trend, with the exception of the composites containing only GNs, while those reinforced solely with MWCNTs exhibited the best performance. The O2 permeability measurements revealed that the highest reduction in the permeability was observed in GN-MWCNT/PDMS composite membranes, in comparison to those reinforced only with graphene or carbon nanotubes. Dielectric relaxation spectroscopy showed that all the examined composites, and especially those of MWCNTs, possess electrical conductivity, apart from the samples reinforced exclusively with graphene. The electromagnetic shielding effectiveness was also improved at higher filler loadings, which is more evident in composites reinforced with MWCNTs. It was concluded that the improved properties of the above studied hybrid composites make them suitable for protective coating applications.

Synthesis of fluorinated ether free aromatic backbone copolymers containing trifluoromethyl and dimethylamino groups for CO2 separation: Investigation of pure and mixed gas performance under dry and humid conditions

A novel series of linear, high molecular weight aromatic copolymers containing trifluoromethyl and dimethylamino groups was synthesized via facile super-acid catalyzed polyhydroxyalkylation and investigated as CO2 gas separation membrane materials. The molar ratio of the two ketone comonomers used in copolymerization, trifluoroacetophenone (TFAp) and N,N-dimethylamino trifluoroacetophenone (dMATFAp), was systematically varied to produce five copolymers with different dMATFAp contents ranging from 12 to 73 %. The influence of dMATFAp content on physicochemical and mechanical properties as well as pure gas and water vapor separation performance was studied. All synthesized copolymers displayed excellent film forming ability, high thermal stability and high Tg values (Tgs > 380 °C). Pure gas permeability measurements revealed that the increase of dMATFAp molar content from 12 % to 34 % resulted in improved gas permeability, while, on the contrary, further increase of dMATFAp content from 34 to 73 % led to substantial gas permeability decrease ascribed to FFV decrease. In particular, among copolymers, the one with dMATFAp content of 34 % presented the highest CO2 permeability value of 290 Barrer due to its highest CO2 diffusion and CO2 solubility coefficients associated with its higher FFV value. The CO2/CH4 performance of synthesized copolymers fell very close to 2008 upper bound limit and exceeded most of the super-acid catalyzed copolymer membranes reported in the literature and commercial membranes. CO2/CH4 and CO2/N2 selectivity values for the different synthesized copolymers were in the range of 29.9–40 and 22.7–44, respectively. The study of the effect of dMΑTFA on water permeability unveiled that the membrane with the highest dMΑTFAp molar content (73 %) showed the highest water permeability value (23,100 Barrer) as well. This was attributed to the increased concentration of N-methyl substituent of dMΑTFAp which can interact with water molecules thereby increasing solubility. Under process gas stream conditions using a mixture of 3 % H2O-48.5 % CO2-48.5 % CH4, both CH4 and CO2 permeability were significantly reduced (by 35 % and 47 %, respectively) due to the preferential sorption of water vapor over other gases present in the mixture, highlighting the negative effect of water vapor on gas permeability. Accordingly, the CO2/CH4 separation factor was slightly increased from 23.8 to 29. Finally, stability test of the copolymer (BP-TFAp)66-(BP-dMATFAp)34 at 40 °C under humid mixed gas conditions showed that CO2 and CH4 permeability remained unchanged for one month after an initial condition stabilization that is required implying that these copolymer structures are promising materials for CO2 separation.

Comprehensive analysis of gas slippage and Non-Darcy flow in carbonate rock samples under stress conditions

This study examines the influence of stress on gas slippage and non-Darcy flow behavior in carbonate porous media, using core samples from two large carbonate reservoirs in the Middle East. Permeability measurements under varying stress conditions revealed significant increases in both the gas slippage factor and the non-Darcy coefficient with rising stress, indicating a related decrease in permeability. A new mathematical model, incorporating effective tortuosity and slippage radius into the Kozeny-Carman equation, was developed to accurately describe the stress-dependent nature of gas flow. Analysis of key pore attributes—such as porosity, pore size, shape, and tortuosity—underscored the critical role of pore structure, especially pore size and connectivity, in governing fluid flow under stress. These findings highlight the need to account for stress effects in reservoir engineering for improved modeling and management of carbonate reservoirs.

Leveraging molecular scale free volume generation to improve gas separation performance of carbon molecular sieve membranes

Carbon molecular sieve (CMS) membranes have proven to be promising candidates for next-generation gas separations. Modification of polymeric precursors is a critical tool that permits fine-tuning of CMS structure and performance for a wide variety of gas mixtures. Here, we make a targeted alteration to a polyimide CMS precursor through substitution of free-volume-generating trifluoromethyl groups for aliphatic methyl groups on the polymer backbone. Gas separation performance shows a vast improvement, demonstrated by up to an eightfold increase in gas permeability as well as higher mixed gas separation factors in some cases. We investigate these properties, and their dependence on pyrolysis temperature, with detailed measurements of gas sorption and permeation in CMS dense film membranes with additional analysis through classical materials characterization methods. Our observations indicate that addition of free-volume-generating groups into polymeric precursors is a powerful tool for developing state-of-the-art CMS membranes, especially in cases when high permeability is an important design parameter.

Multiscale Pore Architecture and Its Influence on Porosity, Permeability, and Fluid Flow in Tight Gas Reservoirs of the Shihezi H8 Formation, Ordos Basin

Characterizing pore network morphology and its influence on critical reservoir properties such as porosity, permeability, and fluid flow pathways is imperative for maximizing production from tight gas sandstone reservoirs. This study integrated petrographic and pore-scale analyses to investigate diagenetic effects on the Shihezi H8 Formation, Ordos Basin, China. Sixty core plug samples spanning depositional facies from wells were analyzed using thin-section petrography, scanning electron microscopy, laser grain size analysis, mercury injection capillary pressure (MICP), nuclear magnetic resonance (NMR), and porosity–permeability measurements. Thin-section observations indicated that formation primarily comprises litharenite and sub-litharenite sandstones deposited in fluvial–deltaic environments composed primarily of quartz and feldspar grains. Diagenesis caused significant porosity reduction through initial mechanical compaction, 3–13% quartz cementation, and localized dissolution, resulting in secondary porosity of up to 5%. Three diagenetic facies were differentiated based on variations in mineralogy and diagenetic alterations. MICP classified pore networks into three reservoir types defined by mean throat radii ranging from 0.091 to 0.270 μm. NMR distinguished pore architectures as uniformly microporous, bimodally micro–mesoporous, and heterogeneously distributed multiscale pores. Larger throat radii correlated positively with higher porosity (up to 8.6%), gas porosity (10.5%), and permeability (0.1911 mD). Grain size analysis demonstrated a positive correlation between mean detrital grain diameter (>2.6 φ, 0.18 mm, (180 µm)), and significantly elevated average porosity (5–8%) compared to finer lithologies, implying depositional energy and sorting regimes. Integrating depositional features, diagenetic alterations, and multiscale pore architecture characterization quantitatively and qualitatively enhanced predictions of heterogeneity in hydrocarbon flow behavior amongst these tight reservoirs. The optimized insights from this integrated study provide a framework to guide development strategies and field appraisal methods for maximizing recovery from unconventional tight gas formations.

Assessment of wetting conditions in quasistatic drainage modeling using a pore morphology method and J-function wettability estimator

This study hypothesizes that a pore morphology method (PMM) can be used to accurately determine representative contact angles by effectively capturing fluid morphologies within porous media, thereby overcoming the challenges of accurate wettability characterization for porous materials. We introduce a methodology for the estimation of the wettability, along with measurements of capillary pressure and relative permeability, using a PMM. This approach employs morphological operations to model quasistatic drainage under different surface wetting conditions. To assess PMM, fluid morphologies resulting from the simulation were compared with experimentally derived geometric and thermodynamic contact angles, along with surface area, and Euler characteristic measurements. Based on fluid configurations under different wettability conditions, we find that PMM effectively captures realistic fluid morphologies. At lower capillary pressures, PMM exhibits superior adaptability to a wide range of wetting behaviors. However, at higher capillary pressures, PMM does not reflect the true morphologies of the fluid due to the interfaces that exist in the pendular state. The influence of these effects at higher capillary pressures introduces an inaccuracy in the simulated relative permeability of the wetting phase, though they do not affect the relative permeability of the nonwetting phase. Overall, these findings can significantly enhance the accuracy of wettability characterization in porous media, thereby advancing our understanding and prediction of fluid behavior in surface-based research of porous materials.

Effect of temperature on permeability of mudstone subjected to triaxial stresses and its application

In order to prevent leakage of pyrolysed oil and gas and the release of contaminants from the top and bottom strata, it is essential to carry out a comprehensive study of the seepage behaviour of these strata under high temperature triaxial stress conditions. The findings of this study will contribute to the development of effective strategies for the containment and integrity monitoring of subsurface reservoirs and storage environments. Mudstone, serving as both the upper and lower strata, offers an effective barrier due to its inherently low permeability. In order to explore the change rule of mudstone sealing performance under high temperature triaxial stress, an air-heated low permeability rock mass air permeability measurement system is used to measure the ground stress buried 500 m deep and the temperature variation characteristics of mudstone permeability on the roof and floor of Jimsar oil shale in Xinjiang under 100 °C. It was found that the permeability of stressed mudstone decreased with the temperature rising up to 100 °C. The primary factor influencing the outcome was the thermal expansion of the mudstone. The magnitude of the drop value was contingent upon the triaxial stresses that could potentially be induced by the application of significant tensile forces, resulting in a relatively minor drop value. The average hydraulic radius of pore in the mudstone was also calculated, which also exhibited continuous reduction as heating up to 100 °C and the degree of reduction could reach 68%. The capacity, that prevent oil & gas and contaminant from moving cross strata as a barrier, would be strengthened when the mudstone strata from roof and floor experienced the temperature low than 100 °C. The barrier performance of mudstone as a pollutant migration barrier layer to gas pollutant migration during in-situ heat injection mining of oil shale was further evaluated.

Abstract 4137891: Treated HIV infection is not associated with carotid vascular inflammation or plaque progression as assessed by dynamic contrast magnetic resonance imaging

Background: Inflammation and immune dysregulation are thought to drive residual cardiovascular disease risk among persons living with HIV (PLWH) despite effective viral suppression with antiretroviral therapy (ART). Question: We investigated differences in carotid vascular inflammation and atherosclerosis in a longitudinal cohort of virally suppressed PLWH (n = 50; on stable ART with CD4 >250 cells/mm 3 , viral load <200 copies/mL for >6 months) and HIV-uninfected controls (n = 51) matched for age, sex, hypertension, diabetes, smoking, hyperlipidemia, and family history of premature coronary artery disease. Methods&Results: Participants were > 40 years old at enrollment, 8% female, and had a high prevalence of cardiovascular risk factors ( Table 1 ). Measures of carotid inflammation and capillary permeability ( K trans ), neovascularization ( V p ), and wall thickness were assessed at baseline, 1 year, and change over 1 year by dynamic contrast-enhanced magnetic resonance imaging. Both PLWH and controls demonstrated a reduction in systolic and diastolic blood pressures and total cholesterol over 1 year; however, the difference was not significant by HIV status. PLWH had a significant reduction in triglycerides compared with controls (-48.8 mg/dL vs 12.8 mg/dL; p = 0.026). HIV was not associated with baseline, follow-up, or change in markers of systemic inflammation assessed by plasma cytokines (C-reactive protein, interleukin-6, interleukin-1ß), nor vascular inflammation or plaque as assessed by K trans , V p , carotid wall thickness, or percent wall volume ( Tables 2 & 3 ). Conclusions: In contrast to other studies of chronically treated and virally suppressed PLWH, HIV infection was not associated with carotid inflammation or plaque.

Towards standardisation of the out-of-plane permeability measurement for reinforcement textiles

In the collaborative effort towards standardisation of out-of-plane permeability measurement, an international benchmarking exercise was carried out whereby 19 participants worldwide were instructed to measure the out-of-plane permeability following a number of strict guidelines, informed by the outcomes of the first international benchmarking exercise completed in 2021. This paper presents the results of the exercise and an assessment of the reproducibility of the data and the suitability of the proposed test method. The data returned were subjected to a number of statistical analysis methods, which showed that adherence to the test guidelines resulted in a high likelihood of a participant not being an outlier and therefore providing evidence that the test method proposed in this paper is a suitable way forward for a standardised test method.

Permeability Measurement of Pervious Concrete by Constant and Falling Head Methods: Influence of Aggregate Gradation and Cement-to-Aggregate Ratio

Permeability Measurement of Pervious Concrete by Constant and Falling Head Methods: Influence of Aggregate Gradation and Cement-to-Aggregate Ratio

Assessment of the Potential for CO2 Storage and Utilization in the Fractured and Porous Reservoir of the Cambrian Sandstones in West Lithuania’s Baltic Basin

Cambrian sandstones comprise a large and saline-only aquifer that can be utilized for CO2 geological storage in the Baltic basin, including Lithuania. The two prospective storage sites with the most potential are located in west Lithuania. Despite the larger area of the Gargždai elevation (233 km2), the Syderiai uplift (62 km2) is characterized by the largest storage volume. The most significant difference between the studied structures is primarily related to the much higher reservoir quality of the Cambrian sandstones at the Syderiai site. The sandstones’ average porosity is 16% and their permeability measures 310 mD, while the Gargždai site is characterized by poor reservoir quality (average porosity of 7% and permeability as low as 10 mD in the sandstone). The main controlling parameter for the sandstones is authigenic quartz cementation. The reservoir type is classified as the porous sandstone type for the Syderiai site and as the fractured reservoir type for the Gargždai site. The storage volumes of CO2 of the sites were assessed as 56.7 Mt and 31.3 Mt, respectively. The present study determined that the Syderiai uplift was the prospective site with the most potential for the geological storage trapping of CO2, owing to its high reservoir quality, while the Gargždai elevation is characterized as a potential alternative for CO2 storage combined with EOR technology for oil exploitation, despite its poor reservoir quality.

Cryogenic fracturing efficacy in granite rocks: Fracture toughness and brazilian test differences after elevated temperatures and liquid nitrogen exposure

Hot dry rock (HDR) is a significant contingent as a thermal energy source. Due to its low permeability, considerable depth, high temperature (150–650 °C), and high pressure, the stimulation of HDR is challenging. This research work aims to examine the efficacy of cryogenic fracturing on HDR. We performed fracture toughness and indirect tensile stress (Brazilian tests) on granite specimens with three different initial temperatures before exposure to liquid nitrogen (LN2). Fracture toughness tests were implemented on semicircular bend (SCB) specimens containing a pure mode-I fracture, and Brazilian tests were performed with discs. The experimental outcomes show that, overall, both critical load in Brazilian tests and the fracture toughness of LN2-treated specimens of granites both diminished with increasing initial temperature. When the initial temperature exceeded 300 °C (in this instance, 500 °C), the amplitude of thermally induced fractures in granite moderately increased after LN2 treatment, secondary fractures prolonged, and the plastic characteristics increased. Moreover, permeability measurements indicated amelioration with elevated temperatures and subsequent LN2 exposure. SEM analysis showed that an increase in initial temperatures along with LN2 treatment led to further intensified granite microdamage while the quantity and the magnitude of thermal fractures augmented.

Assessment of equine intestinal epithelial junctional complexes and barrier permeability using a monolayer culture system.

Gastrointestinal disease is a leading cause of death in mature horses. A lack of in vitro modeling has impeded the development of novel therapeutics. The objectives of this study were to develop and further characterize a small intestinal monolayer cell culture derived from equine jejunum including establishing normal measurements of intestinal permeability and restitution. Three-dimensional enteroids, derived from postmortem sampling of equine jejunum, were utilized to develop confluent epithelial monolayers. The presence of differentiated intestinal epithelial cell types and tight junctions were confirmed using histology, reverse transcription PCR (RT-PCR), RNAscope, protein immunofluorescence and transmission electron microscopy. Transepithelial resistance (TER) and macromolecule flux were assessed as measurements of paracellular and transcellular permeability. Scratch assays were utilized to model and assess intestinal restitution. Monolayer cell cultures reached 100% confluency by ~5-7 days. Equine jejunum monolayers were confirmed as epithelial in origin, with identification of differentiated intestinal epithelial cell types and evidence of tight junction proteins. Function of the intestinal barrier was supported by acquisition of physiologically normal TER values (179.9 ± 33.7 ohms*cm2) and limited macromolecule flux (22 ± 8.8% at 60 min). Additionally, following a scratch wound, epithelial cell monolayers migrated to close gap defects within 24 h. In conclusion, this study describes the development of a novel intestinal epithelial monolayer cell culture for equine jejunum, and provides evidence of intestinal epithelial cell differentiation, formation of physiologically relevant barrier function and use as a model of intestinal restitution to test potential therapeutics for equine colic.

Novel approaches to improving gas separation: Ionic liquids coated coke/ NH2-UiO-66-based mixed matrix membranes for CO2/N2 separation

Permeability and separation efficiency of mixed matrix membranes (MMMs) are two important aspects. Polymeric membranes offer excellent mechanical and physical properties; however, they have a low permeability. To enhance the permeability and separation performance of polyvinyl chloride (PVC) membranes, Cholinium amino acid-based (IL) were impregnated with activated coke/ NH2-UiO-66 (Zr) (AC/MOF) composite and then IL@AC/MOF filler was incorporated into PVC matrix. FTIR spectroscopy, TGA, SEM, EDX, and Brunauer-Emmett-Teller (BET) surface area measurement were used to characterize the MMMs prepared. The porous structure of MMMs nanocomposites causes AC/MOF composite to effectively accelerate gas the diffusion in the PVC matrix. The permeability measurements for CO2 and N2 were made at 288.15, 298.15, 308.15, and 318.15 K at pressure 3 bar The outcomes indicates that the incorporation of the IL@AC/MOF filler increased the permeability of the PVC/AC/MOF MMMs compared to the pure polymeric membrane. The mixed matrix membranes exhibit superior gas separation performance, surpassing the 2008 Robson's Upper Bound.

Impact of gut permeability on estimation of oral bioavailability for chemicals in commerce and the environment.

Performance of pharmacokinetic models developed using in vitro-to-in vivo extrapolation (IVIVE) methods may be improved by refining assumptions regarding fraction absorbed (Fabs) through the intestine, a component of oral bioavailability (Fbio). Although in vivo measures of Fabs are often unavailable for non-pharmaceuticals, in vitro measures of apparent permeability (Papp) using the Caco-2 cell line have been highly correlated with Fabs. We measured bidirectional Papp for over 400 non-pharmaceutical chemicals using the Caco-2 assay. A random forest quantitative structure-property relationship (QSPR) model was developed using these and peer-reviewed pharmaceutical data. Both Caco-2 data (R²=0.37) and the QSPR model (R²=0.29) were better at predicting human bioavailability compared to in vivo rat data (R²=0.23). After incorporation into a high throughput toxicokinetics (HTTK) framework for IVIVE, the Caco-2 data were used to estimate in vivo administered equivalent dose (AED) for bioactivity assessed in vitro, The HTTK-predicted plasma steady state concentrations (Css) for IVIVE were revised, with modest changes predicted for poorly absorbed chemicals. Experimental data were evaluated for sources of measurement uncertainty, which were then accounted for using the Monte Carlo method. Revised AEDs were subsequently compared with exposure estimates to evaluate effects on bioactivity:exposure ratios, a surrogate for risk. Only minor changes in the margin between chemical exposure and predicted bioactive doses were observed due to the preponderance of highly absorbed chemicals.

Improved Fracture Permeability Evaluation Model for Granite Reservoirs in Marine Environments: A Case Study from the South China Sea

Permeability is a crucial parameter in the exploration and development of oil and gas reservoirs, particularly in unconventional ones, where fractures significantly influence storage capacity and fluid flow. This study investigates the fracture permeability of granite reservoirs in the South China Sea, introducing an enhanced evaluation model for planar fracture permeability based on Darcy’s law and Poiseuille’s law. The model incorporates factors such as fracture heterogeneity, tortuosity, angle, and aperture to improve permeability assessments. Building on a single-fracture model, this research integrates mass transfer equations and trigonometric functions to assess intersecting fractures’ permeability. Numerical simulations explore how tortuosity, angle, and aperture affect individual fracture permeability and the influence of relative positioning in intersecting fractures. The model makes key assumptions, including minimal consideration of horizontal stress and the assumption of unidirectional laminar flow in cross-fractures. Granite outcrop samples were systematically collected, followed by full-diameter core drilling. A range of planar models with varying fracture apertures were designed, and permeability measurements were conducted using the AU-TOSCAN-II multifunctional core scanner with a steady-state gas injection method. The results showed consistency between the improved model and experimental findings regarding the effects of fracture aperture and angle on permeability, confirming the model’s accuracy in reflecting the fractures’ influence on reservoir flow capacity. For intersecting fractures, a comparative analysis of core X-ray computed tomography (X-CT) scanning results and experimental outcomes highlighted discrepancies between actual permeability measurements and theoretical simulations based on tortuosity and aperture variations. Limitations exist, particularly for cross-fractures, where quantifying complexity is challenging, leading to potential discrepancies between simulation and experimental results. Further comparisons between core experiments and logging responses are necessary for model refinement. In response to the challenges associated with evaluating absolute permeability in fractured reservoirs, this study presents a novel theoretical assessment model that considers both single and intersecting fractures. The model’s validity is demonstrated through actual core experiments, confirming the effectiveness of the single-fracture model while highlighting the need for further refinement of the dual-fracture model. The findings provide scientific support for the exploration and development of granite reservoirs in the South China Sea and establish a foundation for permeability predictions in other complex fractured reservoir systems, thereby advancing the field of fracture permeability assessment.

A Study on the Breakthrough Pressure of Porous Rock Formations in Gas Storage Reservoirs

Breakthrough pressure of natural gas in rock is an important evaluation parameter in gas reservoir development. In this study, experimental measurements of porosity and permeability of the caprock core were carried out. A digital core model was obtained by body rendering of rock CT (Computed Tomography) slices using Avizo software. Then, the grid model was imported into Fluent software for a numerical simulation of natural gas breakthrough pressure in the core. The innovations of this paper include (1) an accurate calculation method of cap breakthrough pressure based on the VOF method; (2) the method performs a perceptual analysis of average pore radius, wettability, roughness height, and viscosity ratio.

House FIRSTLIFE in student contest and in Living Lab

Abstract The paper comments on selected measurements and observations related to the FIRSTLIFE house demonstration unit, which was prepared by the team of the Czech Technical University for the international competition Solar Decathlon Europe 21/22 with its final at the Solar Campus in Wuppertal, Germany. The paper comments on the measurement results obtained during the competition in the field of building physics (thermal and moisture comfort, measurement of air permeability, measurement of sound insulation of the perimeter wall and dynamic co-heating test). The second part of the paper describes selected follow-up activities. For the purposes of the Living Lab, eight of the competition houses remained on the Solar Campus for at least another 3 years. This allowed long-term monitoring and targeted experiments to be carried out and some of the earlier measurements to be repeated under different climatic boundary conditions. For this phase, additional sensors were added in the Czech house, such as a meteorological station and temperature and heat flow sensors in the perimeter wall. Part of the data comes directly from the building management system. The paper comments on first results from Living Lab period.