Pedicle Screw Length Research Articles

Influence of Screw Length and Cement Position Within the Injured Vertebra on Fixation Strength in Short-Segment Fixation of Osteoporotic Thoracolumbar Burst Fractures

The prevalence of osteoporotic vertebral fractures has increased with aging populations, necessitating effective treatments such as percutaneous kyphoplasty combined with posterior screw fixation. However, biomechanical research on the effects of using short screws on fixation stability and bone stress or on the impact of bone cement bonding to screws on structural strength is lacking. This study aimed to optimize short-segment fixation strategies for osteoporotic thoracolumbar burst fractures by analyzing the biomechanical effects of pedicle screw length and bone-cement augmentation. Four models of the thoracolumbar spine were established using computed tomography data of a female volunteer: (1) short screws in the injured vertebra without contact with the bone cement, (2) long screws without contact with the bone cement, (3) long screws in contact with the bone cement; and (4) long screws without the bone cement. The four fixation models were simulated under physiological loads. The range of motion, implant stress, and segmental stability were assessed. The three groups containing the bone cement exhibited similar performances in terms of stability and stress distribution, whereas the group without the bone cement exhibited a poorer biomechanical performance. Incorporation of the bone cement enhanced the biomechanical properties of the structure, and short screws in the injured vertebra without contact with the bone cement did not significantly compromise the biomechanical performance. Short screws in injured vertebrae without contact with the bone cement can achieve satisfactory stability and stress distribution. It is feasible to implant short screws in the injured vertebrae, reduce the number of bilaterally injured vertebrae, and inject bone cement through the non-pedicle approach during the surgical procedure, which simplifies the surgical process.

Evaluation of crankshaft phenomenon after posterior fusion for early onset scoliosis using an inverse trigonometric function: a multicenter retrospective cohort study.

The crankshaft phenomenon (CSP) is a corrective loss after posterior surgery for early onset scoliosis (EOS). However, an accurate method for CSP evaluation has yet to be developed. In this study, we evaluated pedicle screw (PS) length and rotation angle using an inverse trigonometric function and investigated the prevalence of the CSP. Fifty patients from nine institutions (mean age 10.6years, male/female ratio 4:46) who underwent early definitive fusion surgery at ≤ 11years of age were included. The rotation angle was calculated as arctan (lateral/frontal PS length) using radiography. Measurements were taken at the apex and lower instrumented vertebra (LIV) immediate, 2-, and 5-year postoperatively. CSP was defined as a rotation angle progression ≥ 5°. We divided patients into CSP and non-CSP groups and measured the demographic parameters, Risser grade, state of the triradiate cartilage, major coronal Cobb angle, T1-T12 length, T1-S1 length, and presence of distal adding-on (DAO). We compared these variables between groups and investigated the correlation between the measured variables and vertebral rotation. Logistic regression analysis investigated factors associated with CSP. The rotation angle progressed by 2.4 and 1.3° over 5years for the apex and LIV, respectively. CSP occurred in 15 cases (30%), DAO in 11 cases (22%), and CSP and DAO overlapped in 4 cases (8%). In the CSP group, the T1-T12 length was low immediate postoperatively. The rotation angle was negatively correlated with preoperative height (r = -0.33), T1-T12 length (r = -0.35), and T1-S1 length (r = -0.30). A lower preoperative T1-T12 length was associated with CSP (odds ratio: 0.996, p = 0.048). CSP occurred in 30% of patients with EOS who underwent definitive fusion. The presence of CSP was associated with a lower preoperative T1-T12 length. Diagnosis, level IV.

Measurement of Postoperative Apical Vertebral Rotation Using Radiographic Images in Adolescent Idiopathic Scoliosis-Quantitative Evaluation Using Inverse Trigonometric Functions.

Conventional methods for analyzing vertebral rotation are limited to postoperative patients who underwent posterior fusion. A previous methodology calculated vertebral rotation using inverse trigonometric functions based on the length of the pedicle screw (PS). Accordingly, this study evaluates rotational deformity in patients with postoperative adolescent idiopathic scoliosis (AIS) using inverse trigonometric functions. This retrospective single-center study includes patients with AIS who underwent posterior fusion surgery. Postoperative radiography and computed tomography (CT) scans were retrospectively evaluated. The magnification ratio was calculated using the rod diameter (δ=lateral/frontal rod diameter), and the visible screw lengths were measured using radiographs. The rotation angle was calculated using the apex of the main curve and the lower instrumented vertebra (LIV) (rotation angle=tan-1 (lateral PS length/(δ×frontal PS length))) immediately following the surgery as well as two and five years postoperatively. The correlation between the direct CT measurement and postoperative rotation angle progression was investigated. The crankshaft phenomenon (CSP) and distal adding-on (DAO) were evaluated as postoperative deformities. CSP was defined as a 5° increase in rotation angle. Seventy-eight patients (age: 15.3±2.0 years, eight boys and seventy girls) were included. The rotation angle was strongly correlated with CT rotation measurements (r=0.87). The mean rotation angle at the apex and LIV did not change within five years postoperatively (mean: 0.5±3.6° and 0.4±3.4°, respectively). CSP and DAO were observed in 6.4% and 3.8% of patients, respectively. The inverse trigonometric method is useful to quantitatively evaluate the postoperative rotation angle and identify CSP.

Floor-Mounted Robotic Pedicle Screw Placement in Lumbar Spine Surgery: An Analysis of 1,050 Screws.

To analyze the usage of floor-mounted robot in minimally invasive lumbar fusion. Patients who underwent minimally invasive lumbar fusion for degenerative pathology using floor-mounted robot (ExcelsiusGPS) were included. Pedicle screw accuracy, proximal level violation rate, pedicle screw size, screw-related complications, and robot abandonment rate were analyzed. Two hundred twenty-nine patients were included. Most surgeries were primary single-level fusion. Sixty-five percent of surgeries had intraoperative computed tomography (CT) workflow, 35% had preoperative CT workflow. Sixty-six percent were transforaminal lumbar interbody fusion, 16% were lateral, 8% were anterior, and 10% were a combined approach. A total of 1,050 screws were placed with robotic assistance (85% in prone position, 15% in lateral position). Postoperative CT scan was available for 80 patients (419 screws). Overall pedicle screw accuracy rate was 96.4% (prone, 96.7%; lateral, 94.2%; primary, 96.7%; revision, 95.3%). Overall poor screw placement rate was 2.8% (prone, 2.7%; lateral, 3.8%; primary, 2.7%; revision, 3.5%). Overall proximal facet and endplate violation rates were 0.4% and 0.9%. Average diameter and length of pedicle screws were 7.1 mm and 47.7 mm. Screw revision had to be done for 1 screw (0.1%). Use of the robot had to be aborted in 2 cases (0.8%). Usage of floor-mounted robotics for the placement of lumbar pedicle screws leads to excellent accuracy, large screw size, and negligible screw-related complications. It does so for screw placement in prone/lateral position and primary/revision surgery alike with negligible robot abandonment rates.

Size selection and placement of pedicle screws using robot-assisted versus fluoroscopy-guided techniques for thoracolumbar fractures: possible implications for the screw loosening rate

BackgroundThere has been increased development of robotic technologies for the accuracy of percutaneous pedicle screw placement. However, it remains unclear whether the robot really optimize the selection of screw sizes and enhance screw stability. The purpose of this study is to compare the sizes (diameter and length), placement accuracy and the loosening rate of pedicle screws using robotic-assisted versus conventional fluoroscopy approaches for thoracolumbar fractures.MethodsA retrospective cohort study was conducted to evaluate 70 consecutive patients [34 cases of robot-assisted percutaneous pedicle screw fixation (RAF) and 36 of conventional fluoroscopy-guided percutaneous pedicle screw fixation (FGF)]. Demographics, clinical characteristics, and radiological features were recorded. Pedicle screw length, diameter, and pedicle screw placement accuracy were assessed. The patients’ sagittal kyphosis Cobb angles (KCA), anterior vertebral height ratios (VHA), and screw loosening rate were evaluated by radiographic data 1 year after surgery.ResultsThere was no significant difference in the mean computed tomography (CT) Hounsfield unit (HU) values, operation duration, or length of hospital stay between the groups. Compared with the FGF group, the RAF group had a lower fluoroscopy frequency [14 (12–18) vs. 21 (16–25), P < 0.001] and a higher “grade A + B” pedicle screw placement rate (96.5% vs. 89.4%, P < 0.05). The mean screw diameter was 6.04 ± 0.55 mm in the RAF group and 5.78 ± 0.50 mm in the FGF group (P < 0.001). The mean screw length was 50.45 ± 4.37 mm in the RAF group and 48.63 ± 3.86 mm in the FGF group (P < 0.001). The correction loss of the KCA and VHR of the RAF group was less than that of the FGT group at the 1-year follow-up [(3.8 ± 1.8° vs. 4.9 ± 4.2°) and (5.5 ± 4.9% vs. 6.4 ± 5.7%)], and screw loosening occurred in 2 out of 34 patients (5.9%) in the RAF group, and 6 out of 36 patients (16.7%) in the FGF group, but there were no significant differences (P > 0.05).ConclusionCompared with the fluoroscopy-guided technique, robotic-assisted spine surgery decreased radiation exposure and optimizes screw trajectories and dimensions intraoperatively. Although not statistically significant, the loosening rate of the RAF group was lower that of than the FGT group.

Ideal entry point and trajectory for C2 pedicle screw placement in children: a 3D computed tomography study.

To identify the ideal entry point for pediatric C2 pedicle screw and to obtain parameters of it for the indication of pediatric atlantoaxial fusion arthrodesis. The pediatric cervical CT images were reconstructed into the 3D digital models and the C2 vertebrae were separated. The location of ideal entry point and screw placement related linear and angular parameters were assessed on the 3D digital models. A total of 214 pedicles from 107 C2 digital models were analyzed. The average entry point for C2 was 3.80 ± 2.78mm medial to the lateral notch (LN) and 2.57 ± 1.70mm superior to the LN. The average pedicle diameter (PD) was 6.02 ± 1.31mm, and the average pedicle screw length (PSL) was 25.63 ± 3.46mm. Statistical differences were found between different sex for PD and PSL (P < 0.05). As patient age increases, using the most lateral and inferior edge of the lateral mass as a reference marker, the entry point tends to move medial and cephalad, when using the LN as a reference marker, the entry point tends to move medial and slightly caudad. Univariate linear regression analysis suggested that these linear parameters were associated with age (P < 0.01). In this study, we found that the measurement results of C2 pedicle screw varied based on sex, laterality, and ages for children younger than 18years. The entry point of the screws facilitating ideal trajectory tends to change in a linear way as a function of age. This information helps the surgeon to establish the specific anatomy related to C2 pedicle screw placement to facilitate fixation in the pediatric patients.

Assessment of conformity of actual thoraco-lumbar pedicle screw dimensions to manufacturers' specifications.

Although correct selection of pedicle screw dimensions is indispensable to achieving optimum results, manufacturer-specified or intended dimensions may differ from actual dimensions. Here we analyzed the reliability of specifications made by various manufacturers by comparing them to the actual lengths and diameters of pedicle screws in a standardized experimental setup. We analyzed the actual length and diameter of pedicle screws of five different manufacturers. Four different screw lengths and for each length two different diameters were measured. Measurements were performed with the pedicle screws attached to a rod, with the length determined from the bottom of the tulip to the tip of the screw and the diameters determined at the proximal and distal threads. Differences in length of > 1 mm were found between the manufacturers' specifications and our actual measurements in 24 different pedicle screws. The highest deviation of the measured length from the manufacturers' specification was 3.2 mm. The difference in length between the shortest and longest screw with identical specifications was 3.4 mm. The highest deviation of the measured proximal thread diameters and the manufacturer's specifications was 0.5 mm. The diameter of the distal thread depends on the shape of the pedicle screw and hence varies between manufacturers in conical screws. We found clear differences in the length of pedicle screws with identical manufacturer specifications. Since differences between the actual dimensions and the dimensions indicated by the manufacturer may vary, this needs to be taken into account during the planning of spine instrumentation.

Special Considerations to Improve Clinical Outcomes in Patients with Osteoporosis Undergoing Spine Surgery.

Osteoporosis is a condition that is commonly encountered, with increasing diagnosis by the medical community with the aging population. Osteoporosis leaves patients susceptible to fragility fractures in the vertebrae and is also associated with degenerative changes, both of which may require intervention from a spine surgeon. The goal of this review is to concisely outline special nonoperative adjuncts, as well as preoperative, intraoperative, and postoperative considerations of osteoporotic patients undergoing spine intervention. A literature analysis was completed for this narrative review. A database search of PubMed and Google Scholar was conducted using "osteoporosis" combined with "spine," "spine surgery," and "spinal fusion" without exclusion based on publication date. Articles were screened to exclude duplicate articles and screened for their full text and English language availability. The database search yielded recent publications from which the narrative review was completed. Preoperatively, screening is traditionally completed with dual-energy x-ray absorptiometry (DEXA). Pharmacological therapy modalities currently include teriparatide, raloxifene, denosumab, bisphosphonates, and calcitonin. In order to prevent operative complications associated with osteoporosis, surgeons have found success in increasing the diameter and the length of pedicle screws, limiting pedicle tapping, achieving bicortical or even tricortical purchase, augmenting with polymethyl methacrylate, using iliosacral stabilization, preventing positive sagittal balance, and using adequate fusion products when necessary. Postoperatively, it is important to implant a care plan that includes adequate pain control and necessary care, and to understand risks associated with falls may increase risk of postoperative fragility fractures as well as instrumentation displacement. At this time there are no recommendations in regard to bracing in the postoperative setting. This review article outlines the most current evidence-based medicine with regard to considerations in spine surgery of the osteoporotic patient, and aims to bring about new questions to be investigated in that paradigm.

Demographic Analysis of Pedicle Diameter, and Estimated Pedicle Screw Length of the Lumbar Spine in a Diverse Population.

Recent literature confirms the importance of understanding the variability in pedicle morphology among races. These studies suggest that more detailed and reliable measurements of pedicles should be undertaken. However, there is limited data on average pedicle diameters (PDs) or estimated pedicle screw lengths (EPSLs) between diverse racial populations. We sought to determine the differences in PD and EPSL in the lumbar spine between various races: "Asian," "Black," "White," and "Hispanic" to aid in perioperative planning during instrumented spinal fusion. Axial cuts of 404 patients were inspected to obtain their transverse outer cortical PD as measured through the isthmus, and EPSL by measuring the posterior entry point at the longest distance, which perpendicularly transected the measured isthmic diameter, to the anterior vertebral cortex from L1 to L5. We examined the average PD and PD range at each level for each race. To determine the significance, we used a mixed analysis of variance and a post hoc analysis. In this retrospective chart review the races were found to be significantly different in PD and EPSL (P < .001). Post hoc analysis using Dunn-Bonferroni correction showed that Asians had significantly smaller PDs than Blacks and Whites (P < .002 and P < .014, respectively). The White and Hispanic population had significantly longer EPSLs when compared to Blacks and Asians from L1 to L5 (P < .01). This study demonstrates that there are significant differences in pedicle morphology among races that must be taken into consideration when inserting pedicle screws during lumbar spinal fusion. Knowledge of these differences is of the utmost importance in order to limit complications while improving fixation. 3. Pedicle morphology is variable between races and understanding these differences is important for the safe placement of pedicle screws.

Comparison of Preoperative Pedicle Screw Measurement Between Computed Tomography and Magnet Resonance Imaging.

Pedicle screw fixation is commonly used in the treatment of spinal pathologies. While the biomechanical factors that affect bone fixation have been frequently described, questions remain as to which imaging modality is the ideal medium for preoperative planning. Due to its perceived superiority in assessing bony changes, computed tomography (CT) scan is assumed to be the gold standard for preparative planning, and we hypothesize that magnetic resonance imaging (MRI) is sufficiently accurate to predict screw length and diameter compared to CT. We retrospectively measured the length and diameter of vertebral bodies in the lumbar region in both MRI and CT and tested for differences between the modalities as well as for confounding effects of age, sex, and the presence of spondyloarthrosis. We found a significant difference in pedicle screw length between CT and MRI measurements for both sides. For the left pedicle, the mean difference was 1.89 mm (95% confidence interval [CI] -3.03 to -0.75; P < .002), while for the right pedicle, the mean difference was 2.05 mm (95% CI -3.27 to -0.84; P = .001). We also found a significant difference in diameter measurements between CT and MRI for the left pedicle (0.53 mm; 95% CI 0.13 to 0.93; P = .011) but not for the right pedicle (0.36 mm; 95% CI -0.06 to 0.78; P = .094). We identified no significant effect of sex, age or spondyloarthrosis on the results (P > .05). Pedicle screw planning measurements were more accurate using CT images compared to MRI images. CT scan remains the gold standard for pedicle screw planning in trauma surgery. When using MRI images, the surgeon should be aware of the differences in screw length and diameter compared to CT in order to avoid intra- and postoperative risks.

Experimental study of individualized 3D printing-guided template combined with thoracolumbar pedicle screw placement for the treatment of ankylosing spondylitis

To evaluate accuracy and safety of individualized 3D printing guided template for thoracolumbar pedicle screw placement in patients with ankylosing spondylitis. From January 2016 to September 2019, thoracolumbar spine three-dimensional CT data of 8 patients with ankylosing spondylitis were included, Mimics 17.0 and ideaMaker computer software were applied to design thoracolumbar pedicle screw guided template of patients with AS, physical model of all patients (T10-L2)were printed by 3D printer, 2 parts in each patient, and divided into guide-plate-assisted screw group (experimental group) and free-hand nail group (control group). Thoracolumbar pedicle screws of both groups were placed by the same spinal surgeon. The accuracy of pedicle screw placement between two groups were evaluated according to results of postoperative CT, the accuracy of the fixation of thoracolumbar pedicle screw was divided into 4 grades, grade 0 and 1 screws were acceptable nails, grade 2 and 3 screws were unacceptable nails. The diameter and length of pedicle screws, the distance between entry point and posterior median line designed by preoperative 3D printing were compared with actual use in operation. Twenty three blocks of thoracolumbar 3D printing screw of ankylosing spondylitis guided templates were designed and printed in guide-plate-assisted screw group, 46 screws were inserted and 44 screws were accepted. The time of implanting a screw into thoracolumbar pedicle was (4.20±1.15) min, the frequency of X-ray was (5.00±1.25) times and the average adjustment times of screw and Kirschner needle during screw placement was (1.76±1.32) times. In the control group, 46 nails were placed by traditional surgical method and 30 screws were accepted. The time of implanting a screw into thoracolumbar pedicle was (14.67±2.23) min, the frequency of X-ray fluoroscopy was (14.46±2.21) times and the average times of Kirschner needle adjustment was (4.76±3.39) times. The success rates between experimental group and control group were 95.65%(44 / 46) and 56.22%(30 / 46) respectively, and had statistical difference (χ2=13.538, P<0.05). There was no significant difference in diameter, length of pedicle screws and the distance of posterior median line between virtual designed by 3D printing before operation and actual situation in opertaion (P>0.05). The operation time of inserting a single screw, the times of X-ray fluoroscopy, and the average times of adjustment screw and Kirschner needle in experimental group were significant less than those in control group(P<0.01). The personalized guide template assisted the thoracolumbar fixation designed by 3D printing could significantly improve safety, accuracy and efficiency of surgery, especially suitable for thoracolumbar vertebral bodies requiring posterior pedicle screw fixation for fracture or dislocation with AS.

The Optimal Screw Length of Lumbar Pedicle Screws during Minimally Invasive Surgery Fixation: A Computed Tomography-Guided Evaluation of 771 Screws.

Study DesignA retrospective study of radiographic parameters of patients who underwent lumbar spinal pedicle screw insertion.PurposeThe optimal length of pedicle screws is often determined by the lateral radiograph during minimally invasive surgery (MIS). Compared with open techniques, measuring the precise length of screws or assessing the cortical breach is challenging. This study aims to ascertain the optimal pedicle screw lengths on intraoperative lateral radiographs for L1–L5.Overview of LiteratureResearch has revealed that optimal pedicle screw length is essential to optimize fixation, especially in osteoporotic patients; however, it must be balanced against unintentional breach of the anterior cortex, risking injury to adjacent neurovascular structures as demonstrated by case reports.MethodsWe reviewed intra- and postoperative computed tomography scans of 225 patients who underwent lumbar pedicle screw insertion to ascertain which of the inserted screws were ‘optimal screws.’ The corresponding lengths of these screws were analyzed on postoperative lateral radiographs to ascertain the ideal position that a screw should attain (expressed as a percentage of the entire vertebral body length).ResultsWe reviewed 880 screws of which 771 were optimal screws. We noted a decreasing trend in average optimal percentages of insertion into the vertebral body for pedicle screws going from L1 (average=87.60%) to L5 (average=78.87%). The subgroup analysis revealed that there was an increasing percentage of screws directed in a straight trajectory from L1 to L5, compared to a medially directed trajectory.ConclusionsDuring MIS pedicle screw fixation, this study recommends that pedicle screws should not exceed 85% of the vertebral body length on the lateral view for L1, 80% for L2–L4, and 75% for L5; this will minimize the risk of anterior cortical breach yet maximize pedicle screw purchase for fixation stability.

Determining the Optimal Length and Safety of Pedicle Screws in the T12 Vertebra: A Morphometric Study.

Introduction: Despite the developments in implant technology and imaging methods and the advances in surgical techniques, there are still potential problems and complications of transpedicular screw application. This is a morphometric study to examine the proximity of the T12 vertebra to the thoracic aorta. Our aim was to define the appropriate length of the pedicle screw to be used in the 12th thoracic vertebra, using computed tomography (CT) data.Methods: Randomly selected cases from the same ethnic group in a specific age group were examined in terms of the length from the anterior vertebral body and the screw entry point of the T12 vertebra to the thoracic aorta. In light of these data, a statistical analysis was made for the selection of the most appropriate screw length.Results: A statistically significant difference was detected in the distance from the T12 left screw entry point to the aorta between males and females (p=0.001). No statistically significant correlation was found between age and the distance between the left screw entry point and the aorta (p=0.105). Also, no statistically significant difference was detected between the T12 vertebral body-aorta distance in males and in females (p=0.212). The relationship between the shortest aorta-vertebral body distance and age was not statistically significant (p=0.7). Similarly, there was no statistically significant difference between the left screw entry point-aorta distance and the aorta-vertebral body shortest distance (p=0.731).Conclusions: Significant differences were observed between males and females in terms of the distance between the T12 vertebra left screw entry point and the thoracic aorta (p=0.001). Thus, we can assert the need for the preoperative evaluation of patients with computed tomography in selecting the appropriate screw length and avoiding complications.

Efficacy of 3D print guide technique in one stage posterior approach for the treatment of cervical and thoracic tuberculosis with kyphosis

Objective: To investigate the application of 3D printing technology in the treatment of patients with cervical kyphosis and paraplegia in different segments of the cervical spine after one-stage debridement, bone graft fusion and pedicle screw fixation. Methods: From January 2008 to January 2017, a total of 31 patients with thoracolumbar tuberculosis were treated in the Department of Orthopaedics, the Xinjiang Uygur Autonomous Region people's Hospital.Lesions of the thoracic spine (T1-T4) in 8 cases, (C5-C7) in 10 cases, cervical and thoracic segment in 13 cases, involving a total of 2 cases of vertebral body in 7 cases, 3 cases of vertebral body in 14 cases, 4 cases of vertebral body. 3D printing group (group A) 12 cases, non 3D printing group (group B) of 19 cases.All cases were treated with a posterior approach to the treatment of the cervical spinal cord around the spinal cord.After taking regular anti tuberculosis drugs in 6-12 months, follow-up observation of correction of kyphosis and paraplegia recovery, blood sedimentation rate (ESR), C-reactive protein (CRP) changes. Results: All cases were followed up for at least 6 months. Twelve patients were treated with 3D printing technique before operation, and the operation was performed according to the preoperative plan.The diameter and length of pedicle screws, the direction of insertion, and the distance between the insertion point and the posterior midline of the pedicle screw were similar to those in the 3D.Three days after the operation, the effect of fracture reduction was satisfactory, and the position of pedicle screws was good.After 6 months of follow-up, the X-ray showed that the pedicle screws were in good position, and there was no loosening and fracture.All the patients were healed, and there was no segmental instability.3D printing group during surgery bleeding, operation time, postoperative drainage volume, compared with the non 3D print group of surgical results, 3D printing group significantly reduce the surgical trauma[(131±18) min vs (162±23), P<0.01; (528±34) ml vs (615±41) ml, P<0.01; (257±46) vs (327±56), P<0.01; (not grouping, before after operation), (64±42) mm/1 h vs (6±7) mm/1 h, P<0.01; CRP (not packet): (72±41) μg/L, (13±6) mm/1 h, P<0.01]. There was significant difference between two groups.The JOA scores of patients in the 3D group were better than those in the non 3D group after the operation in 1, 2 week and in 1, 3, and month.There was no significant difference between the two groups after the operation.Two groups of patients before and after correction of Cobb angle were satisfied, and no significant difference between the two groups.Cobb lost an average of 1 degrees angle correction.The spinal tuberculosis in this group were cured without serious complications. Conclusions: According to the cervical and thoracic tuberculous kyphosis and paraplegia severity, choose a posterior surgery can achieve effective cure, feasible thorough debridement with fixed spinal stability before and after the party obtained bone fusion and deformity correction in 3D technology to increase the accuracy and safety of operation, and can be provide more detailed preoperative, intuitive, three-dimensional, realistic personalized operation scheme.It can reduce the operation trauma, and achieve rapid recovery after operation.

Morphometric Measurement of the Lumbosacral Spine for Minimally-Invasive Cortical Bone Trajectory Implant Using Computed-Tomography

Introduction The cortical bone trajectory (CBT) is a novel lumbar pedicle screw trajectory. There is a dearth of literature on CBT screw insertion techniques. The aim of this study was to conduct a detailed morphometric measurement of the lumbosacral spine for CBT pedicle screw starting point, trajectory, length and diameter, using the inferior facet of the cephalad level as a bony landmark. Methods The 3-dimensional reconstruction computed tomography (CT) scans of 86 adults who underwent examination of the lumbosacral spine were studied. The junction of the inferior and medial border of the smallest coronal section of the lumbar pedicle was traced in lumbar segments while the junction of the medial border of the sacral 1 (S1) pedicle and the inferior border of the L5 inferior facet was traced in S1 segments. The starting point was defined to be the projective point on the vertebral plate by this junction. The distances from the starting point to the inferior, lateral and medial border of the inferior facet of the cephalad level, and the inferior border of the transverse process were measured. The trajectory of pedicle screws for the lumbar and S1 segments was determined in the axial and sagittal planes. The angle formed between this trajectory and a line from the vertebral midline was defined as the transverse angle (TA). The angle formed between this trajectory and a line from superior margin of the vertebral body was defined as the cephalad angle 1 (CA1). Cephalad angle 2 (CA2) was defined as the angle formed between the same trajectory on the sagittal plane and a line from the posterior margin of the pars interarticularis. The maximum pedicle screw diameter, as well as the maximum pedicle screw length of the lumbosacral segments was measured on axial and sagittal CT scans, respectively. Results The distances from the inferior border of inferior facet to the starting point from L1 to S1 were 8.9, 6.3, 4.1, 2.9, 1.4 and 0 mm, respectively. The distances from the medial border of the inferior facet to the starting point from L1 to S1 were between 3 to 4mm. The percentages of the distance from the starting point to the medial border of the inferior facet from L1 to S1 were 80.5, 70.1, 61.6, 48.6, 40.8 and 29.3%, respectively. TA from L1 to S1 were 9.0, 9.6, 11.3, 13.5, 15.5, and 8.2 degrees, respectively. CA1/CA2 from L1 to S1 were 26.7/38.7, 26.0/38.7, 26.9/38.0, 24.4/37.2, 22.9/35.1 and 18.4/47.8 degrees, respectively. The maximum diameters of the trajectory from L1 to S1 were 4.8, 5.1, 6.1, 6.8, 7.8, and 6.1mm, respectively. Twenty-five mm was a safe border as the maximum length of the pedicle screw from L1 to S1. Conclusions The inferior facet of the cephalad level is an attractive bony landmark for establishing a starting point of CBT for minimally-invasive spine surgery.

Determining Optimal C2 Pedicle Screw Placement and Length in Patients with Axis Traumatic Spondylolisthesis: A Case Series

Introduction “Axis traumatic spondylolisthesis” (ATS) and “Hangman's fracture” are terms that describe a specific fracture group, which involves the posterior C2 elements. Wood-Jones first described a C2 vertebra fracture in 1913. He described fractures produced by hanging, and observing that the lesion was produced by a violent cervical traction with abrupt stretching of the head backward, leading to C2 pedicle fractures. Later in 1964, Garber2 described C2 pedicle fractures with a forward dislocation of the C2 body in victims of motor vehicle accidents, called “axis’ traumatic spondylolisthesis.” In 1965, Schneider et al3 described another series of patients with the same fractures, naming them “Hangman's Fracture.” The ATS was referred to as an uncommon and predominantly stable lesion, rarely accompanied by neurological deficit, for which the recommended treatment was cervical traction and rigid immobilization. Materials and Methods From June 2008 to April 2010, nine patients with axis traumatic spondylolisthesis with or without C2-3 sub-laxation were operated. All patients were admitted and operated at Dr. Soliman Fakeeh Hospital, Jeddah, Saudi Arabia. There were eight males and one female, with a mean age of 35.7 years. Eight patients had a motor vehicle accident and one fell from second floor into the street. Two patients had a previous conservative treatment, and showed signs of pseudarthrosis at the fracture site, with intense pain at the cervical spine region. Three patients had head injury, two of them with multiple cranial fractures and the third was submitted for surgical treatment for a ruptured cervical disc. Three patients had dislocation of C2-C3, which was not satisfactorily reduced with conservative treatment. None of the patients showed neurological deficit. Results The mean follow-up period was 6 months (range, 3-9 months). All nine patients had good postoperative improvement with satisfactory fracture consolidation, and asymptomatic on follow-up. There were no intra or postoperative complications, except one patient who developed pneumonia on postoperative day 3, which resolved in 7 days of antibiotic treatment. The hospitalization period varied from 7 to 13 days. Only one patient developed frequent neck pain, especially after performing intense physical effort, which improved after rest, use of nonsteroidal analgesics, and simple physiotherapeutic remedies. On immediate plain radiographic evaluation, all patients showed satisfactory and correct alignment of fractured bony ends with C2-C3 reduction. Six months after surgery, all patients undertook a CT scan where good healing of the fractures with intact pedicle cortices. There were a total of 18 pedicles inserted in all patients. The mean pedicle screw length was 16.5 mm (range: 16-17 mm), and the mean medial and rostral inclinations measured were 34.7 degrees (range: 28-41 degrees) and 38.6 degrees (range: 28-41 degrees), respectively. Conclusion There were many explicit limitations in our study, such as the small number of patients, the single-center, single-surgeon, retrospective design, very short follow-up (was as short as 3 months), lack of standardized outcomes measures, and lack of standardized criteria to assess fusion status. Nonetheless, based on the frequent observations of the bony anatomic variations and the lines of fractures brought about by trauma, the classic 20-degree inclinations in both trajectories previously suggested should be reconsidered. However, fixed angles of angulations cannot be generalized. As a consequence, we conclude that accurate preoperative planning could be obtained with the use of 3D reconstructed CT images that can preoperatively predict the best screw length needed for the procedure, depending on the size of the patient's axis vertebra, and the best angulations for the safety of the neighboring neurovascular structures, Hence, it is important to understand the patient's individual anatomy, as this is the ultimate guide to proper placement despite understanding the angles. Anatomic landmarks can therefore be well seen and demarcated through the use of intraoperative fluoroscopy or image guided navigation techniques. Disclosure of Interest None declared

Biomechanical impact of C2 pedicle screw length in an atlantoaxial fusion construct.

Background:Posterior, atlantoaxial (AA) fusions of the cervical spine may include either standard (26 mm) or short (16 mm) C2 pedicle screws. This manuscript focused on an in vitro biomechanical comparison of standard versus short C2 pedicle screws to perform posterior C1-C2 AA fusions.Methods:Twelve human cadaveric spines underwent C1 lateral mass screw and standard C2 pedicle screw (n = 6) versus short C2 pedicle screw (n = 6) fixation. Six additional controls were not instrumented. The peak torque, peak rotational interval, and peak stiffness of the constructs were analyzed to failure levels.Results:The peak torque to construct failure was not statistically significantly different among the control spine (12.2 Nm), short pedicle fixation (15.5 Nm), or the standard pedicle fixation (11.6 Nm), P = 0.79. While the angle at the peak rotation statistically significantly differed between the control specimens (47.7° of relative motion) and the overall instrumented specimens (P < 0.001), the 20.7° of relative rotation in the short C2 pedicle screw specimens was not statistically significantly higher than the 13.7° of relative rotation in the standard C2 pedicle screw specimens (P = 0.39). Similarly, although the average stiffness was statistically significantly lower in control group (0.026 Nm/degree) versus the overall instrumented specimens (P = 0.001), the standard C2 pedicle screws (2.54 Nm/degree) did not differ from the short C2 pedicle screwsConclusions:Both standard and short C2 pedicle screws allow for equally rigid fixation of C1 lateral mass-C2 AA fusions. Usage of a short C2 pedicle screw may be an acceptable method of stabilization in carefully selected patient populations.

A multi-level rapid prototyping drill guide template reduces the perforation risk of pedicle screw placement in the lumbar and sacral spine

The method of free-hand pedicle screw placement is generally safe although it carries potential risks. For this reason, several highly accurate computer-assisted systems were developed and are currently on the market. However, these devices have certain disadvantages. We have developed a method of pedicle screw placement in the lumbar and sacral region using a multi-level drill guide template, created with the rapid prototyping technology and have validated it in a clinical study. The aim of the study was to manufacture and evaluate the accuracy of a multi-level drill guide template for lumbar and first sacral pedicle screw placement and to compare it with the free-hand technique under fluoroscopy supervision. In 2011 and 2012, a randomized clinical trial was performed on 20 patients. 54 screws were implanted in the trial group using templates and 54 in the control group using the fluoroscopy-supervised free-hand technique. Furthermore, applicability for the first sacral level was tested. Preoperative CT-scans were taken and templates were designed using the selective laser sintering method. Postoperative evaluation and statistical analysis of pedicle violation, displacement, screw length and deviation were performed for both groups. The incidence of cortex perforation was significantly reduced in the template group; likewise, the deviation and displacement level of screws in the sagittal plane. In both groups there was no significantly important difference in deviation and displacement level in the transversal plane as not in pedicle screw length. The results for the first sacral level resembled the main investigated group. The method significantly lowers the incidence of cortex perforation and is therefore potentially applicable in clinical practice, especially in some selected cases. The applied method, however, carries a potential for errors during manufacturing and practical usage and therefore still requires further improvements.

Pneumomediastinum, Subcutaneous Emphysema, and Tracheal Tear in the Early Postoperative Period of Spinal Surgery in a Paraplegic Achondroplastic Dwarf

Achondroplasia was first described in 1878 and is the most common form of human skeletal dysplasia. Spinal manifestations include thoracolumbar kyphosis, foramen magnum, and spinal stenosis. Progressive kyphosis can result in spinal cord compression and paraplegia due to the reduced size of spinal canal. The deficits are typically progressive, presenting as an insidious onset of paresthesia, followed by the inability to walk and then by urinary incontinence. Paraplegia can be the result of direct pressure on the cord by bone or the injury to the anterior spinal vessels by a protruding bone. Surgical treatment consists of posterior instrumentation, fusion with total wide laminectomy at stenosis levels, and anterior interbody support. Pedicle screws are preferred for spinal instrumentation because wires and hooks may induce spinal cord injury due to the narrow spinal canal. Pedicle lengths are significantly shorter, and 20–25 mm long screws are appropriate for lower thoracic and lumbar pedicles in adult achondroplastic There is no information about the appropriate length of screws for the upper thoracic pedicles. Tracheal injury due to inappropriate pedicle screw length is a rare complication. We report an extremely rare case of tracheal tear due to posterior instrumentation and its management in the early postoperative period.

Preoperative Templating Before Spinal Fusion Using a Fluoroscopic Multiplanar Imaging System is as Accurate as CT Scan and Uses Substantially Less Radiation

Many surgeons utilize preoperative multiplanar imaging for surgical planning before fusion surgery using pedicle screw instrumentation. Computed tomographic (CT) scan is often used but limited by non-weight-bearing images and high-ionizing radiation. The purpose of this study was to compare pedicle length and width measurements using a multiplanar fluoroscopic imaging system and CT with gross measurements to validate the accuracy of multiplanar fluoroscopic imaging and compare relative radiation exposure between techniques. Thirteen intact cadaveric lumbar spine segments were imaged using multiplanar fluoroscopic imaging and conventional CT scan using a low-dose pediatric protocol. At each level and each imaging modality, the 26 pedicles were measured digitally for width and pedicle screw length in accordance with typical presurgical planning procedures. All images were independently measured by 3 observers. After measurement, the specimens were sectioned using a microsurgical saw to facilitate anatomic measurements using calipers. Measurements of the multiplanar fluoroscopic imaging and CT were compared with direct anatomic measurements to quantitate and compare measurement accuracy of CT and fluoroscopic imaging. At the time of image acquisition, radiation exposure from each modality was quantified to allow for comparison of radiation exposures. CT and multiplanar fluoroscopy had similar agreement with gross measurements with respect to pedicle width and length, with κ values for comparison of CT and fluoroscopy with gross measurements falling between 0.61 and 0.73. Both modalities underestimated pedicle width (by 1.9 mm for both modalities) and length (5.5 mm for CT, 6.6 mm for fluoroscopy). Interobserver reliability was higher for fluoroscopy versus CT. High-dose fluoroscopic imaging used 31% of the radiation exposure for CT. Multiplanar fluoroscopic imaging provides comparable diagnostic preoperative planning to CT scan in an experimental cadaveric model. The use of multiplanar fluoroscopic imaging resulted in between 69% and 85% less radiation exposure than conventional CT scan using pediatric settings. This study demonstrates similar results from simulated preoperative templating using fluoroscopic imaging compared with CT scan but with less radiation exposure.