Pd Nanoparticles Research Articles

Oxygen Vacancy-Enriched Alumina Stabilized Pd Nanocatalysts for Selective Hydrogenation of Phenols.

The prevalence of electronic defects has not been successfully demonstrated in nonreducible oxides. This work presents a straightforward approach to the preparation of a yellow alumina rich in F-centers (oxygen vacancies containing free electrons), which is well characterized by systematic spectral methods. The surface electron density of the as-prepared F-center enriched alumina sample was estimated to be approximately 0.35 mmol·g-1. Free electrons on the surface can reduce palladium precursors in situ, leading to the deposition of fine Pd nanoparticles on alumina. The produced Pd nanocatalysts are highly effective in the selective hydrogenation of phenol to cyclohexanone, achieving a high catalytic performance under mild conditions (30 °C and 0.1 MPa of H2). Systematic mechanism investigations reveal that hydroxyl radicals generated at the catalyst interfaces facilitate the activation of phenol. The activated phenol is then sequentially hydrogenated to give the intermediate 2-cyclohexenone and then the desired cyclohexanone. The catalyst system demonstrates efficacy in selectively hydrogenating substituted phenols into a wide array of functional ketones.

Electrodeposition Decoration of Pd0 on F‐Co(OH)2 Nanoarrays with Intentionally Introduced Pd2+ Species for Efficient Electrocatalytic Hydrodechlorination of 2,4‐Dichlorophenol

AbstractDeveloping a Pd‐based catalyst possessing high efficiency and low mass loading remains a big obstacle for the large‐scale application of electrocatalytic hydrodechlorination (EHDC) of chlorophenols (CPs). Herein, high dispersion Pd nanoparticles imbedded in Pd2+ hydroxide species are decorated on the surface of F−Co(OH)2 nanowire arrays with a newly developed electrodeposition and hydrolysis coupled process. EHDC of 2,4‐dichlorophenol (2,4‐DCP) with the as‐obtained Pd/F−Co(OH)2/NF‐a exhibits superior performance than other control samples in this work and literature reports. A 100 % removal of 2,4‐DCP is accomplished within 120 min, featuring fast reaction kinetics (kobs=5.0×10−2 min−1) and mass activity (MA=22.2 min−1 g−1Pd). Mechanism investigation shows that the intentionally introduced Pd2+ sites play a pivotal role in the adsorption of 2,4‐DCP, while high dispersion of Pd facilitates the generation of active H*, thus promoting the catalytic performance. This work presents a valuable example for designing high‐performance Pd‐based EHDC catalysts by composition tuning.

Pd Nanoparticles Decorated CeZrOx for Enhanced Photocatalytic Hydrogenation of Biomass‐Derived Compounds

The photocatalytic conversion of biomass‐derived compounds into value‐added chemicals presents a promising protocol for the sustainable production of renewable chemicals. Our study explores the hydrogenation of biomass model compounds under visible light illumination. Zr was incorporated into the CeO2 framework, forming a CeZrOx(1:0.5) solid solution, confirmed by powder X‐ray diffraction (PXRD) and X‐ray photoelectron spectroscopy (XPS) analyses. The light uptake capacity of the CeZrOx solid solution was characterized using UV‐visible spectroscopy. Additionally, the band structure of the CeZrOx solid solution was assessed using valance band X‐ray photoelectron spectroscopy (VB‐XPS) and Ultraviolet photoelectron spectroscopy (UPS) analysis, revealing a Z‐Scheme, which was further confirmed by various control experiments. Upon decorating the CeZrOx(1:0.5) solid solution with 1 wt% palladium (Pd), the resulting 1Pd/CeZrOx(1:0.5) composite exhibited improved charge separation and enhanced visible light absorption capacity. This composite achieved ~99% conversion of furfural to tetrahydrofurfuryl alcohol under a 15 W blue LED illumination and 0.2 MPa hydrogen. Similarly, it demonstrated ~99% conversion of benzyl phenyl ether (BPE) to toluene and phenol under a 10 W blue LED illumination. Our findings elucidate the active sites and demonstrate the recyclability of mixed metal oxides for selective furfural hydrogenation and BPE hydrogenolysis under visible light.

Self‐Polycondensation Flux Synthesis of Ultrastable Olefin‐Linked Covalent Organic Frameworks for Electrocatalysis

AbstractCreating new functional materials that efficiently support noble metal catalysts is important and in high demand. Herein, we develop a self‐polycondensation flux synthesis strategy that can produce olefin‐linked covalent organic framework (COF) platforms with high crystallinity and porosity as the supports of Pd nanoparticles for electrocatalytic nitrogen reduction reaction (ENRR). A series of “two in one” monomers integrating aldehyde and methyl reactive groups are rationally designed to afford COFs with square‐shaped pores and ultrahigh chemical stability (e.g., strong acid or alkali environments for >1 month). Functionalizing Fluorine significantly boosts the hydrophobicity of fluoro‐functionalized COFs, which can inhibit the competing hydrogen evolution reaction (HER) and enhance ENRR performances. The COFs loading Pd nanoparticles show high NH3 production yields up to 90.0±2.6 μg ⋅ h−1 ⋅ mgcat.−1 and the faradaic efficiency of 44 % at −0.2 V versus reversible hydrogen electrode, the best comprehensive performance among all reported COFs. Meanwhile, the catalysts are easy to recover and recycle, as demonstrated by their use for 15 cycles and 17 hours, with good performance retention. This work not only provides a new synthesis strategy for olefin‐linked COFs, but also paves a new avenue for the design of highly efficient ENRR catalysts.

Pd/UiO‐66(Zr)‐2OH as a High‐Performance Catalyst for Hydrogen‐Enhanced Fenton Oxidation of Trimethoprim

ABSTRACTA novel catalyst material named Pd/UiO‐66(Zr)‐2OH was successfully developed and applied in a hydrogen‐promoted Fenton system for the efficient catalytic oxidation of the widely used antibiotic trimethoprim (TMP). The UiO‐66(Zr)‐2OH, as the carrier of catalyst in this work, was synthesized through a solvothermal method. The Pd0 nanoparticle, as the active center of the catalyst, was loaded onto its surface by the “ship‐in‐a‐bottle” strategy. The results showed that the composite Pd/UiO‐66(Zr)‐2OH demonstrated excellent catalytic performance during the reaction, achieving over 97% of TMP removal efficiency within 180 min under optimal conditions under the condition of only trace of iron without adding H2O2. This may be attributed to the fact that the [H], as a clean and efficient reducing agent, can be utilized to accelerate the regeneration of Fe2+ in the Fenton reaction, as well as in the in‐situ regeneration of H2O2. The key parameters affecting the removal efficiency of TMP, including the initial pH and concentration of Fe2+, the dosage of the synthesized material, the flow rate of H2 and the stirring speed were investigated systematically. The Pd/UiO‐66(Zr)‐2OH exhibited high stability and reusability, maintaining over 82% of its initial degradation efficiency of TMP after six reaction cycles. The mechanistic insight revealed that the system primarily relied on the generation of hydroxyl radical (·OH) and singlet oxygen (1O2) for the degradation of TMP, which was verified through quenching experiments and electron spin resonance (ESR). The degradation pathway of TMP was elucidated by analyzing intermediates and the reduction in total organic carbon (TOC). This research offers novel conceptual insights into the evolution and application of advanced oxidation technologies, efficient degradation of emerging pollutants, and expansion of pathways for hydrogen resource utilization.

Probing Active Sites on Pd/Pt Alloy Nanoparticles by CO Adsorption.

We studied the adsorption of CO on Pd/Pt nanoparticles (NPs) with varying compositions using polarization-dependent Fourier transform infrared reflection absorption spectroscopy (FT-IRRAS) and theoretical calculations (DFT). We prepared PtPd alloy NPs via physical vapor codeposition on α-Al2O3(0001) supports. Our morphological and structural characterization by scanning electron microscopy and grazing incidence X-ray diffraction revealed well-defined, epitaxial NPs. We used CO as a probe molecule to identify the particles' surface active sites. Polarization-dependent FT-IRRAS enabled us to distinguish CO adsorption on top and side facets of the NPs. The role of the Pd/Pt alloy ratio on CO adsorption was investigated by comparing the experimental CO stretching band frequency for different alloy arrangements to the results for pure Pd and Pt NPs. Moreover, we studied the influence of hydrogen adsorption on the NP surface composition. We determined the dependence of the IR bands on the local atomic arrangement via DFT calculations, revealing that both bulk alloy composition and neighboring atoms influence the wavenumber of the bands.

Rational design of nitrogen-doped carbon for palladium catalysts in hydrogenation of hydrazo compounds

We synthesized CN11, a carbon nitride material rich in sp3 hybrid graphitic nitrogen (sp3-N), employing a facile oxalic acid-assisted melamine molecular assembly strategy. CN11 promoted the formation of Pd nanoparticles (NPs) predominantly exposing {200} facets, termed Pd/CN11-2. This facet-specific configuration significantly boosted hydrogen adsorption, leading to notable improvements in catalytic activity. Compared to Pd/XC-72-2 and Pd/g-C3N4-2, Pd/CN11-2 exhibited a remarkable two-fold and nineteen-fold increase in catalytic yield for hydrazo compound hydrogenation, respectively. Pd/CN11-2 also demonstrated robust performance across a range of reaction conditions, maintaining excellent yield. This study emphasizes the critical role of tailored support structures in controlling Pd NPs facets, thereby enhancing hydrogenation efficiency. It provides valuable insights for advancing the industrial application of Pd-based catalysts, underscoring the importance of strategic support modulation for optimizing catalytic performance.

Solar Light Elimination of Bacteria, Yeast and Organic Pollutants by Effective Photocatalysts Based on Ag/Cr-TiO2 and Pd/Cr-TiO2.

This study focused on searching for more effective nanomaterials for environmental remediation and health protection; thus, coliform bacteria, yeast and the organic food dye sunset yellow were selected as target pollutants to be eliminated under solar light by Ag/Cr-TiO2 and Pd/Cr-TiO2. Firstly, Cr3+ was in situ incorporated into the anatase crystalline lattice by the sol-gel method; then, Ag or Pd nanoparticles were deposited on Cr-TiO2 by chemical photoreduction. The scientific challenge addressed by the development of these composites was to analyse the recovery of Cr, to be employed in photocatalyst formulation and the enhancement of the TiO2 photocatalytic activity by addition of other noble metals. By extensive characterization, it was found that after TiO2 doping with chromium, the parameters of the crystal lattice slightly increased, due to the incorporation of Cr ions into the lattice. The TiO2 band gap decreased after Cr addition, but an increase in the optical absorptions towards the visible region after noble metals deposition was also observed, which was dependent of the Ag or Pd loading. Generally, it was observed that the noble metals type is a factor that strongly influenced the effectiveness of the photocatalysts concerning each substrate studied. Thus, by using Ag(0.1%)/Cr-TiO2, the complete elimination of E. coli from samples of water coming from a highly polluted river was achieved. Pd(0.5%)/Cr-TiO2 showed the highest efficiency in the elimination of S. cerevisiae from a lab prepared strain. On the other hand, the Pd(0.1%)/Cr-TiO2 sample shows the highest dye degradation rate, achieving 92% of TOC removal after 180 min.

UiO-66(Zr)-2OH-Supported Pd0 NP Catalysts Accelerated a Fenton-Like Reaction: Iron Cycling and Hydrogen Peroxide Generation Achieved Simultaneously.

Both the sluggish kinetics of Fe(II) regeneration and usage restriction of H2O2 have severely hindered the scientific progress of the Fenton reaction toward practical applications. Herein, a reduction strategy of activated hydrogen, which was used to simultaneously generate H2O2 and accelerate the regeneration of ferrous in a Fenton-like reaction based on the reduction of activated hydrogen derived from H2, was proposed. Two types of composite catalysts, namely, Pd/UiO-66(Zr)-2OH and Pd@UiO-66(Zr)-2OH, were successfully prepared by loading nano-Pd particles onto the outer and inner pores of UiO-66(Zr)-2OH in different loading modes, respectively. They were used to enhance the reduction of activated hydrogen. The characterization results based on the analysis of scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy revealed that the materials were successfully prepared. By using a trace amount of ferrous iron and without adding H2O2, trimethoprim (C0 = 20 mg·L-1), as a target pollutant, could be nearly 100% degraded within 180 min in the reaction system composed of these two materials. The cycle of iron and the self-generation of H2O2 were verified by the detection of ferrous H2O2 in the system. Density functional theory calculation results further confirmed that the pore-filled Pd0 NPs, as the main catalytic site for Pd@UiO-66(Zr)-2OH, could produce H2O2 under the combined action of hydrogen and oxygen. The Pd@UiO-66(Zr)-2OH system had excellent stability after multiple applications (at least 6 cycles), all of which resulted in 100% removal of trimethoprim. The degradation efficiency of the Pd/UiO-66(Zr)-2OH system for TMP gradually decreased from 97 to 80% after six cycles. The results of electron paramagnetic resonance combined with classical radical burst experiments revealed the degradation pathways in the reaction system with hydroxyl radicals and singlet oxygen as the main reactive oxygen particles.

Chiral Organic Salt Supported Pd Nanoparticles as Selective Heterogeneous Catalysts of Hydrogenation Reactions

AbstractIn this study, we report the synthesis of a new type of chiral crystalline organic porous salt CF2 derived from the ionic reaction between tetrakis(4‐sulfophenyl)methane (TSPM) and the tetra‐(S)‐prolylamide of tetrakis(4‐aminophenyl)methane, (S)‐TPPM, and its ability to stabilize 2 nm palladium nanoparticles to give a novel, nonpyrophoric, chiral, catalytic material Pd@CF2. The preparation of the catalyst was very simple and conducted in water. The heterogeneous catalytic performance of Pd@CF2 was tested in hydrogen reductions of olefins and substituted nitroaromatic compounds using Pd/C as a comparison to determine the specific features of the novel catalyst. Although both types of catalysts exhibited similar catalytic activity in case of reductions of diphenylacetylene and nitrobenzene, Pd@CF2 predominantly promoted the reduction of p‐nitrobenzaldehyde to p‐aminobenzyl alcohol whereas Pd/C gave p‐toluidine. The reduction of p‐dinitrobenzene led to predominant formation of p‐nitrophenylhydroxylamine if promoted by the novel catalyst and to a mixture of products if promoted by Pd/C. In addition, the introduction of p‐alkoxy groups onto nitrobenzenes slowed down the reduction with Pd@CF2 but had no influence on Pd/C activity. A hypothesis ascribing these observations to dissimilar equilibrium distributions of nitro and polar groups within the organic framework and the palladium metal surface is proposed to rationalize the selectivity of the novel catalytic material.

N-Doped Carbon Nitride with Embedded Pd Nanoparticles for Selective Photocatalytic Valorisation of Biomass-Derived Vanillin into Vanillyl Alcohol and 2-Methoxy-4-Methyl Phenol

N-Doped Carbon Nitride with Embedded Pd Nanoparticles for Selective Photocatalytic Valorisation of Biomass-Derived Vanillin into Vanillyl Alcohol and 2-Methoxy-4-Methyl Phenol

Facile Fabrication of LaFeO 3 Supported Pd Nanoparticles as Highly Effective Heterogeneous Catalyst for Suzuki–Miyaura Coupling Reaction

Supported Pd catalysts have been widely studied due to their enormous potential as candidates for heterogeneous Suzuki–Miyaura coupling reactions. However, the sintering and low activity of active sites still remain challenges. A vesicle‐shaped LaFeO3‐supported Pd catalyst (I‐Pd/LaFeO3) was successfully fabricated using the impregnation method and tested for the Suzuki–Miyaura coupling reaction. Compared to P‐Pd/LaFeO3 prepared with photo‐deposition and Pd/Al2O3 prepared with impregnation, the I‐Pd/LaFeO3 catalyst exhibits significantly higher catalytic activity, stability, and reusability. The chemical composition and electron states of different Pd‐based catalysts were well studied based on various characterizations and the results indicated that the excellent performance of I‐Pd/LaFeO3 can be attributed to its unique nanostructure and the strong interactions between LaFeO3 and palladium nanoparticles. The impregnation method and the choice of the LaFeO3 support show a great influence on the electronic properties of Pd species, their reducibility, and, consequently, their reaction behavior. This unique LaFeO3 supported Pd catalyst provided an environmentally friendly heterogeneous method for the Suzuki–Miyaura coupling reaction.

Effect of Electric Field on Carbon Encapsulation and Catalytic Activity of Pd for Efficient Formic Acid Decomposition

Utilizing carbon coated ferroelectric materials to introduce polarization‐induced electric field (PIEF) stimulates research of electric field‐assisted catalysts for various reactions. However, effect of PIEF on carbon coating mechanism has not been studied. Herein, tourmaline nanoparticles (TNPs) with spontaneous dipole moments were applied as the PIEF supplier and sucrose was utilized as the carbon precursor to synthesize carbon coated TNPs (TNP@SC) to uncover the influence of PIEF on the carbon coating and catalytic activity of Pd toward formic acid decomposition (FAD). PIEF enhanced the adsorption capacity of TNPs for the caramelized intermediate species and increased H+ concentration by facilitating water ionization. Polymerization of adsorbed caramelized intermediate species on TNPs was accelerated. Uniformly coated carbon layer with more defects, larger specific surface area, and higher porosity was coated on TNP. Such surface properties of the carbon layer were beneficial for strongly anchoring ultrafine Pd nanoparticles. Owing to the specific properties of carbon layer and existence of PIEF, Pd/TNP@SC exhibited higher FAD activity than the catalysts absent of PIEF. Stronger PIEF leaded to higher initial turnover frequency. This study provides guidance to supply electric field for catalysis.

Solvent-Free Benzyl Alcohol Oxidation Using Spatially Separated Carbon-Supported Au and Pd Nanoparticles

Solvent-Free Benzyl Alcohol Oxidation Using Spatially Separated Carbon-Supported Au and Pd Nanoparticles

Impact of Flame Conditions on the Pd‐O Structure and Methane Oxidation Activity over Ceria Support

AbstractIn this work, we employed flame spray pyrolysis (FSP), a high‐temperature synthesis method, to control the formation of Pd structures on the CeO2 support. Multiple types of Pd structures deposited on CeO2 are observed on FSP‐made samples. Our results show that the oxidizing environment during FSP synthesis facilitates the formation of incorporated Pd2+ structures, along with highly dispersed Pd2+, Pd0 nanoparticles, and Pd° clusters formed under the reducing synthesis condition. Notably, these Pd2+ species remained stable at temperatures up to 400 °C. The catalysts containing both highly dispersed Pd2+ nanoparticles and incorporated Pd2+ species demonstrated superior methane oxidation activity, with higher turnover frequencies than those containing only one type of Pd2+ structure. However, hydrothermal pretreatment in the presence of water vapor led to partial deactivation, likely due to structural alterations in the Pd species or the interaction with the CeO2 support, which reduced the stability and effectiveness of the active sites. This study underscores the importance of both highly dispersed and incorporated Pd2+ species in enhancing catalytic performance and highlights the challenges posed by water‐induced deactivation in practical applications.

High Response and ppb-Level Detection toward Hydrogen Sensing by Palladium-Doped α-Fe2O3 Nanotubes.

Developing hydrogen sensors with parts per billion-level detection limits, high response, and high stability is crucial for ensuring safety across various industries (e.g., hydrogen fuel cells, chemical manufacturing, and aerospace). Despite extensive research on parts per billion-level detection, it still struggles to meet stringent requirements. Here, high performance and ppb-level H2 sensing have been developed with palladium-doped iron oxide nanotubes (Pd@Fe2O3 NTs), which have been prepared by FeCl3·6H2O, PdCl2, and PVP electrospinning and air calcination techniques. Various characterization techniques (FESEM, TEM, XRD, and so forth) were used to prove that the nanotube structure was successfully prepared, and the doping of Pd nanoparticles was realized. The experiments show that palladium doping can significantly improve the gas response of iron oxide nanotubes. Specifically, 0.59 wt % Pd@Fe2O3 NTs have high response (Ra/Rg = 41,000), high selectivity, and excellent repeatability for 200 ppm hydrogen at 300 °C. Notably, there was still a significant response at a low detection limit (LOD) of 50 ppb (Ra/Rg = 16.8). This excellent hydrogen sensing performance may be attributed to the high surface area of the nanotubes, the p-n heterojunction of PdO/Fe2O3, which allows more oxygen to be adsorbed on the surface, and the catalytic action of Pd nanoparticles, which promotes the reaction of hydrogen with surface-adsorbed oxygen.

Pd Nanoparticles Immobilized on Pyridinic N-Rich Carbon Nanosheets for Promoting Suzuki Cross-Coupling Reactions.

Palladium (Pd) catalysts play a crucial role in facilitating Suzuki cross-coupling reactions for the synthesis of valuable organic compounds. However, conventional heterogeneous Pd catalysts often encounter challenges such as leaching and deactivation during reactions, leading to reduced catalytic efficiency. In this study, we employed an innovative intercalation templating strategy to prepare two-dimensional carbon nanosheets with high nitrogen doping derived from petroleum asphalt, which were utilized as a versatile support for immobilizing Pd nanoparticles (Pd/N-CNS) in efficient Suzuki cross-coupling reactions. The results indicate that the anchoring effect of high-pyridinic N species on the two-dimensional carbon nanosheets enhances interactions between Pd and the support, effectively improving both the dispersibility and stability of the Pd nanoparticles. Notably, the Pd/N-CNS catalyst achieved an overall turnover frequency (TOF) of 2390 h-1 for the Suzuki cross-coupling reaction under mild conditions, representing approximately a nine-fold increase in activity compared to commercial Pd/C catalysts. Furthermore, this catalyst maintained an overall TOF of 2294 h-1 even after five reaction cycles, demonstrating excellent stability. Theoretical calculations corroborate these observed enhancements in catalytic performance by attributing them to improved electron transfer from Pd to the support facilitated by abundant pyridinic N species. This work provides valuable insights into feasible strategies for developing efficient catalysts aimed at sustainable production of biaromatic compounds.

Self-supported electrochemical sensor based on uniform palladium nanoparticles functionalized porous graphene film for monitoring H2O2 released from living cells.

Graphene film has been considered a promising material for the construction of self-supported electrodes due to its favorable flexibility and high conductivity. However, the film fabricated from pristine graphene or conventional graphene sheet reduced graphene oxide processes limited electrocatalytic performance. Decorating active metal species or incorporating heteroatoms intothegraphene framework have been proved to be effective methods to enhance the electrocatalytic efficiency of graphene film-based self-supported electrodes. Herein, we present a freestanding electrode composed of uniform Pd nanoparticles decorating N,S co-doped porous graphene film (Pd/NSPGF) and explore its practical application in differentiating various human colon cell types by in situ tracking the amount of H2O2 secreted from live cells. Our findings reveal that, on the one hand, the NSPGF has abundant surface and inner pores, which promote active site exposure, and mass diffusion during electrochemical reactions; on the other hand, the substitutional doping ofthe graphene framework with heteroatoms (e.g., N or S) can tailor its electronic and chemical properties, and facilitate the uniform loading of high-density Pd nanoparticles. Moreover, the intrinsic activity of Pd/NSPGF is regulated by the interaction of Pd nanoparticles withtheNSPGF support. Taking the advantages of morphology and composition, the self-supported Pd/NSPGF electrode displays remarkable electrochemical performance with a wide linear range up to 2.0mM, low detection limit of 0.1μM (S/N = 3), high sensitivity of 665 µA cm-2mM-1, and good selectivity. When applied in real-time trackingofthe H2O2 released from normal human colon epithelial cells and human colorectal cancer cells, the Pd/NSPGF-based electrochemical sensing system can distinguish the cell types by testing the number of extracellular H2O2 molecules released per cell, which holds considerable potential for early detection and monitoring of disease-related clinical specimens.

Upcycling of Chitin to Cross-Coupling Catalysts: Tailored Supports and Opportunities in Mechanochemistry.

In this study chitin derived from shrimp shells was used in the design of heterogeneous Pd-based catalysts for Heck and Suzuki-Miyaura cross-coupling reactions. The synthesis of Pd nanoparticles supported on N-doped carbons was performed through different approaches, including a sustainable mechanochemical approach, by using a twin-screw extruder. All catalytic systems were characterized by a multitechnique approach and the effect of nanoparticles size, N-doping on the support, and their synergistic interactions were elucidated. Specifically, Kelvin Probe Atomic Force Microscopy provided valuable insights on charge transfer and metal-support interactions. The catalytic behaviour of the samples was investigated in cross-coupling reactions under batch conditions and under semi-continuous flow solvent-free conditions, respectively obtaining a quantitative yield and a noteworthy productivity of 8.7 mol/(gPdh).

Palladium nanocrystals immobilized on boron and nitrogen codoped mesoporous carbon spheres as efficient methanol oxidation electrocatalysts

The development of cost-effective and high-performance electrocatalysts is crucial for the widespread application of direct methanol fuel cell. Herein, a convenient and robust method is developed to the controllable fabrication of Pd nanocrystals in situ immobilized on boron and nitrogen codoped mesoporous carbon spheres (Pd/BNMCS) as anode catalysts for the methanol oxidation reaction. The as-derived Pd/BNMCS hybrids are equipped with a series of useful structural features, such as large specific surface area, abundant mesoporous channels, presence of plentiful B and N atoms, well-dispersive Pd nanoparticles, and good electrical conductivity. As a consequence, the optimized Pd/BNMCS catalyst demonstrates superior electrocatalytic methanol oxidation properties in terms of a large electrochemically active surface area, high mass/specific activities, and reliable long-term stability, which are significantly better than those of traditional carbon black and undoped mesoporous carbon sphere supported Pd catalysts. This study highlights the potential of heteroatom codoped mesoporous carbon matrixes in the construction of advanced noble metal electrocatalysts for practical fuel cell applications.