Path Of Electrons Research Articles

Measurement of field emission array current distributions by metal-coated CMOS image sensors

A CMOS image sensor is utilized to determine the time- and spatially resolved distribution of the total electron emission current of a silicon field emission array. The sensor measures electron emission without the need for phosphorus screens or scintillators as converters. However, in initial experiments, rather low field emission currents of several hundreds of nanoamperes per emitter already damaged the sensor surface, which altered the systems’ signal response over the measurement time. In consequence, we coated the CMOS sensor surface with a Cu layer for surface protection. In contrast to the original insulating surface, Cu is an excellent current- and heat-conductor, which avoids lens charging by providing a conductive path for incident electrons and has an improved heat dissipation capability. Measurements using a segmented field emission cathode with four individually addressable tips demonstrate a consistent correlation between the emission current and the sensor signal of the metal-coated image sensor. Furthermore, the characterization of a field emission array showed that single tip emission currents of up to 12 μA per tip are measurable without discernible damage effects of the sensor’s surface.

Construction of Cu-doped α-Fe2O3/γ-Fe2O3 hetero-phase junction composite and its photocatalytic performance

Chlortetracycline hydrochloride (CTC), a class of antibiotics, poses a significant environmental hazard, particularly in aquatic ecosystems. The advancement of highly efficient and readily recyclable materials for water treatment remains an important focus of research in environmental remediation. In this study, Cu-doped α-Fe2O3/γ-Fe2O3 hetero-phase junction materials were prepared by a solvothermal method and a controlled calcination process to enhance the photocatalytic degradation of CTC in water by Fe2O3. Experimental results indicate that the composite material has superior magnetic properties, with Cu2-α-Fe2O3/γ-Fe2O3, featuring a high specific surface area and small pores, showing the best CTC adsorption. The α-Fe2O3/γ-Fe2O3′s interlaced energy levels facilitate quick electron transfer, and copper ion addition optimizes electron paths, generating numerous oxygen vacancies. This, combined with the hetero-phase junction, boosts charge separation and migration. Among the samples tested, The Cu2-α-Fe2O3/γ-Fe2O3 composite demonstrated the most efficient photocatalytic performance, with a degradation rate of 90.19 % for CTC achieved under Visible Light Irradiation. The proposed second-order reaction rate constants were approximately 31.99, 10.07, and 4.48 times higher than those for α-Fe2O3, γ-Fe2O3, and α-Fe2O3/γ-Fe2O3, respectively. The material also demonstrates good degradation effects on other antibiotics (such as oxytetracycline, tetracycline hydrochloride, etc.). Moreover, the structural morphology of the sample remains stable after cycling. O2– and h+ are the main active species in the photocatalytic degradation process of CTC, while OH plays a secondary role. The possible degradation pathways were elucidated by calculating predicted free radical attack sites using density-functional theory (DFT) and by analyzing the products of the CTC degradation process. Additionally, the toxicity risk assessment indicates that the intermediate products have low toxicity and pose a minimal potential risk to the aquatic environment.

Construction of BiVO4/g-C3N4/Ag3PO4 ternary heterojunction with double Z-scheme and its photocatalytic and bacteriostatic properties

A novel Bi-composite photocatalyst BiVO4/g-C3N4/Ag3PO4 with a double Z-scheme structure was prepared by hydrothermal method assisted by honeysuckle extract. When the mass fraction of Ag3PO4 in the composite is 10 %, the inactivation rates of E.coli and S. aureus were 6.9 and 4.6 log, respectively. The MIC results were 0.6 and 0.8 mg/ml, respectively. The capture experiment confirmed that h+ and O2− were the main active substances that catalyzed bacteriostasis. Double Z heterojunction reduces the photochemical corrosion of Ag3PO4, changes the transmission path of photogenerated electrons, and then promotes the separation of photogenerated electron holes, thus obtaining significant photocatalytic activity.

Multidimensional core-shell nanocomposite of iron oxide-carbon tube and graphene nanosheet: A lithium-ion battery anode with enhanced performance through structural optimization

A novel multidimensional composite of 1D iron oxide (Fe3O4)-carbon tube and 2D graphene nanosheet (GNS) was demonstrated to be used as the anode material for lithium-ion batteries (LIBs). Fe3O4-carbon tube-GNS manifested a unique core–shell composite structure, where the Fe3O4 nanoparticles were embedded in the carbon tube with the GNS. The material characterization confirmed that the Fe3O4 nanoparticles were embedded in the highly graphitized carbon tube with the dispersed GNS. Fe3O4-carbon tube-GNS exhibited a high porosity (surface area: 62.3 m2/g, pore volume: 0.112 m3/g). It also exhibited an excellent electrochemical performance with a high reversible capacity (900 mAh/g at 1 A/g), a high coulombic efficiency (∼100 % for 100 cycles), and good rate capability (491 mAh/g at 5 A/g). The excellent electrochemical performance of our composite is attributed to the suppressed/accommodated volume expansion of Fe3O4 and formation of a stable solid electrolyte interphase (SEI) layer during lithiation/delithiation caused by unique multidimensional composite structure of Fe3O4-carbon tube-GNS with a continuous transport path for electrons and Li+. In addition, such the enhanced lithium storage of our composite is confirmed with the kinetic characterization at various scan rates by analyzing their storage and capacitive contributions.

Plasmonic properties of silicon nitride encapsulated copper

We investigated the optical properties (i.e. plasmonic loss) of thin-film copper that was deposited and processed in a 300mm CMOS pilot line. The optical properties at 1550 nm (QSPP,Cu = 3921 ± 350) were evaluated by measuring the propagation loss of dielectric loaded plasmonic waveguides on samples with high and low root mean square surface roughness (Rq) with and without a silicon nitride diffusion barrier and at room temperature and cryogenic temperatures. In our fabrication result, the average grain size is 2.08±0.05μm, which is much larger than the mean free path of free electrons in copper, so the surface roughness becomes the main cause of the waveguide propagation loss from the fabrication constrains. Further, we show that copper can be encapsulated by a 15 nm silicon nitride diffusion and oxidation barrier without degrading the optical properties.

A wearable cotton fiber-based supercapacitor electrode material with outstanding stability and photothermal performance utilizing AgNWs, NiCoAl-LDH, and PPy-NWs

Designing cotton fiber (CF) based flexible electrode materials with both electrochemical energy storage and structural stability is crucial for the utilization of flexible supercapacitors in wearable devices. Nevertheless, the electrochemical properties of such materials are often constrained by suboptimal ion diffusion, a limited electroactive surface area, and inadequate structural integrity. Herein, Silver nanowires (AgNWs), NiCoAl hydrotalcite (NCA-LDH), and polypyrrole nanowires (PPy-NWs) are employed to construct a CF-based electrode material (PNHAS/CF) with high stability through a layer-by-layer self-assembly method. The PNHAS/CF with a high capacitance of 1207.58 mF cm−2 at 5 mA cm−2 due to the faster electronic transmission paths of AgNWs and PPy-NWs, and the high specific capacitance of NCA-LDHs. The NCA-LDH stabilizes the PPy-NWs molecular chain, and the PPy-NWs winding structure can further enhance the PNHAS/CF's structural stability and prevent the AgNWs network from being destroyed, which guarantees the exceptional 87.5 % capacitance retention after 2000 cycles. The constructed symmetrical supercapacitor shows an energy density of 36.28 μWh cm−2 at 0.31 mW cm−2 power density. The PNHAS/CF exhibits superb solar spectral absorptivity (~94.8 %) and outstanding solar heating performance. Surprisingly, the fiber-based flexible electrode material and the assembled supercapacitor are expected to find applications in wearable intelligent electronics.

NiMn-Ag NWs complexes electrode material with in situ grown conductive 3D networks for enhanced supercapacitive performance by boosting Ni2+

Power density is one of the important factors affecting the performance of electrode materials, which is hampered by ion/electron transport and agglomeration build-up problems. In this study, a novel 3D NiMnO3/Ni(OH)2/Ag NWs composite is synthesized via the introduction of Ag NWs. The introduction of Ag NWs synergistically influences the crystal structure and micro-morphology of the NiMnO3/Ni(OH)2/Ag NWs composite. The unique pentatwinned structure of Ag NWs facilitates the enhancement of the (110) and (101) crystal planes, which induces the movement of Ni 2p3/2, leading to a significant increase of Ni2+ concentration in the composites. This ensures an abundance of ion adsorption sites, generating materials conducive to reactive activity. This new structure increases the density of active sites and establishes a conductive network, which optimizes the electron and ion transport paths, greatly reduces the diffusion resistance at the electrode-electrolyte interface, and improves the charge transfer efficiency, thus effectively increasing the specific capacity and energy density of the material. The NiMnO3/Ni(OH)2/Ag NWs//AC device exhibits a remarkable specific capacity of 350.478 mAh·g−1 at a current density of 0.01 A cm−2, and its Ragone plot reveals a peak energy density of 81.107 Wh kg−1 at a power density of 1699.871 W kg−1. Additionally, it achieves an energy density of 60.532 Wh kg−1 at a power density of 8490.072 W kg−1. This study explores the design and application of 3D structured electrode materials, which effectively improves the specific capacity of the materials and provides a new idea to further improve the energy density of supercapacitors.

Preventing Overrides of Severe Drug Allergy Alerts Initiative: an Implemented System Upgrade

Administering medications to patients with documented drug hypersensitivity reactions (DHR) poses a significant risk for adverse events, ranging from mild reactions to life-threatening incidents. Electronic healthcare systems have revolutionized the modern clinical decision-making process, with built in warnings. However, as these alerts become a routine part of healthcare provider’s workflow, alert fatigue becomes a challenge. This study was conducted within the Ministry of National Guard Health Affairs (MNGHA), a government healthcare system in Saudi Arabia. A taskforce of experts was formed to develop an electronic path that would prevent unintentional overrides of severe drug allergy alerts. The system underwent rigorous testing, and monitoring parameters were established. We outline the implementation of a system upgrade designed to trigger an alternative interruption in the computerized physician order entry (CPOE) process, distinct from the regular allergy pop-up alerts. The alternate path is activated upon a CPOE with a drug-to-drug match and a documented severe drug allergy symptom, necessitating co-signature form another prescriber before proceeding. The adopted upgrade is a proactive approach to enhance medication safety in electronic healthcare systems, ensuring that serious allergy-related warnings are not overridden, ultimately enhancing patient safety. Further monitoring will confirm the safety and effectiveness of this measure. This study provides a model for institutions seeking to prevent allergy-related harm within their patient population.

Plasmonic enhancement of Faraday rotation with gold nanodisks with low height-to-diameter aspect ratios

We investigate the Faraday rotation induced in gold nanodisks with low height-to-diameter aspect ratios. Through a systematic study, we analyze the phenomenon using electrostatic theory with the modified long-wavelength approximation. We show that the Faraday rotation is enhanced at the localized surface plasmon resonance when the nanodisk’s effective mean free path is equal to the mean free path of the conduction electrons in the bulk metal, where light absorption dominates over light scattering. We also show that the Faraday rotation is largely enhanced at shorter rather than longer wavelengths.

Tracing the electron transport behavior in quantum-dot light-emitting diodes via single photon counting technique

The electron injection and transport behavior are of vital importance to the performance of quantum-dot light-emitting diodes. By simultaneously measuring the electroluminescence-photoluminescence of the quantum-dot light-emitting diodes, we identify the presence of leakage electrons which leads to the discrepancy of the electroluminescence and the photoluminescence roll-off. To trace the transport paths of the leakage electrons, a single photon counting technique is developed. This technique enables us to detect the weak photon signals and thus provides a means to visualize the electron transport paths at different voltages. The results show that, the electrons, except those recombining within the quantum-dots, leak to the hole transport layer or recombine at the hole transport layer/quantum-dot interface, thus leading to the reduction of efficiency. By reducing the amount of leakage electrons, quantum-dot light-emitting diode with an internal power conversion efficiency of over 98% can be achieved.

Z-scheme heterojunction of TiO2/NH2-MIL-125(Ti) growing on carbon fibers cloth: Photocatalytic degradation of tetracycline and toxicity analysis

Photocatalysis stands out as a promising and eco-friendly method for antibiotics removal, yet traditional photocatalysts, mainly in powder form, are often prone to detachment and loss, making them difficult to recycle and reuse. In this work, we address this challenge by using carbon fiber (CF) cloth with a large area as a carrier for catalysts. To improve the photocatalytic efficiency, we synthesized TiO2 nanorods on the surfaces of CF cloth and incorporate NH2-MIL-125 (Ti) on them, thus the Z-scheme heterojunctions CF/TiO2/NH2-MIL-125(Ti) was obtained. In order to fully understand the structural properties and performance advantages of CF/TiO2/NH₂-MIL-125 (Ti) composites, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray photoelectron spectroscopy (XPS), UV–visible diffuse reflectance spectroscopy (DRS), photoluminescence spectroscopy (PL), Brunauer-Emmett-Teller (BET), Mott-Schottky (M-S) and valence band X-ray photoelectron spectroscopy (VB-XPS). Due to the special electronic transmission path of the Z-scheme heterojunctions, the CF/TiO2/NH2-MIL-125(Ti) composite achieve 95.30 % degradation of tetracycline (TC) within 210 min. The composite also shows exceptional reusability, with a degradation rate of 93.55 % maintained even after four cycles. Finally, we proposed a pathway and catalytic process for the decomposition of TC by CF/TiO2/NH2-MIL-125(Ti) and performed toxicity assessments of TC and its precursors using T.E.S.T. software. This novel photocatalyst composite offers a green and efficient approach for treating antibiotic wastewater, presenting a significant advancement in environmental remediation strategies.

Si particle size blends to improve cycling performance as negative electrode for all-solid-state lithium-ion battery

Silicon negative electrodes dramatically increase the energy density of lithium-ion batteries (LIBs), but there are still many challenges in their practical application due to the limited cycle performance of conventional liquid electrolyte systems. In this study, we clarified that the use of an inorganic solid electrolyte improves the cycle performance of the LIB with the Si negative electrode and the size of Si particles influenced the properties of the all-solid-state LIB. The all-solid-state LIB using micro-sized silicon (mSi) particles as the negative electrode active material showed a large initial discharge capacity (2400 mAh g-1), but the discharge capacity decreased as charge/discharge cycles increased. In contrast, the all-solid-state LIB using nano-sized silicon (nSi) particles showed a low initial discharge capacity (1000 mAh g-1), but the discharge capacity increased for the initial 20 charge/discharge cycles. The cross-sectional images analyzed by scanning electron microscopy showed that for mSi particles, cracks and voids occurred due to volumetric changes during charging and discharging, interrupting the flow path of ions and electrons, whereas for nSi particles, the contact with the solid electrolyte and conductive material was improved. Moreover, the all-solid-state LIB using the negative electrode of nSi: mSi = 7: 3 (mass ratio) showed higher initial discharge capacity and longer cycle performance than that using mSi and nSi.

Carbon Nanotubes Connecting and Encapsulating MoS2-Doped SnO2 Nanoparticles as an Excellent Lithium Storage Performance Anode Material.

Doping and carbon encapsulation modifications have been proven to be effective methods for enhancing the lithium storage performance of batteries. The hydrothermal method and ball milling are commonly used methods for material synthesis. In this study, a composite anode material rich in carbon nanotubes (CNTs) conductive tubular network connection and encapsulation of SnO2-MoS2@CNTs (SMC) was synthesized by combining these two methods. In this highly conductive network, nano-SnO2 particles are uniformly dispersed and embedded in MoS2 with a layered structure, and the obtained SnO2-MoS2 composite material is tightly connected and encapsulated by the tubular network of CNTs. It is worth noting that the incorporation of layered MoS2 not only effectively anchors the SnO2 nanoparticles, but also provides a broader space for lithium-ion movement due to the larger interlayer spacing. The conductive network of CNTs shortens the diffusion path of electrons and Li+ and provides more diffusion channels. The reversible capacity of the SnO2-MoS2@CNTs nanocomposite material remains at 1069.3 mA h g-1 after 320 cycles at 0.2 A g-1, and it exhibits excellent long-term cycling stability, maintaining 904.5 mA h g-1 after 1000 cycles at 1.0 A g-1. The composite material demonstrates excellent pseudocapacitive contribution rate performance, with a contribution rate of 87% at 2.0 mV s-1. The results indicate that SnO2-MoS2@CNTs has excellent electrochemical lithium storage performance and is a promising anode material for lithium-ion batteries.

The electron resistance of a single skyrmion within ballistic approach

An alternative way of skyrmion quasi-particle detection is simulated at low voltage bias. The point contact (PC), attached to the strip with a Néel-type skyrmion, can detect it with a higher efficiency than a magnetic tunnel junction. The method is based on detecting the skyrmion via the ballistic magnetoresistance ratio (BRR). PC's resistance with skyrmion significantly differs from the one without it. BRR is estimated in the framework of the point contact model for two directions of spin-polarized current: perpendicular to the transport direction (case 1) and along one (case 2). Skyrmion's size is assumed to be around 3.6 nm in diameter—smaller, or comparable, to the mean free path of electrons, allowing it to utilize the ballistic transport approach. As a result, resistance values for the considered Néel type skyrmion within the related size are estimated as 157 Ω for case 1 and 452.2 Ω for case 2 with optimistic BRR 101.3% and 291.7%, respectively. BRR for case 2 is higher due to the spin-filtering effect. The method also has the potential to detect the skyrmion type, or other magnetic nano structures such as bimeron, domain wall (DW), etc.

Electron transport through two interacting channels in Azurin-based solid-state junctions

The fundamental question of "what is the transport path of electrons through proteins?" initially introduced while studying long-range electron transfer between localized redox centers in proteins in vivo is also highly relevant to the transport properties of solid-state, dry metal-protein-metal junctions. Here, we report conductance measurements of such junctions, Au-(Azurin monolayer ensemble)-Bismuth (Bi) ones, with well-defined nanopore geometry and ~103 proteins/pore. Our results can be understood as follows. (1) Transport is via two interacting conducting channels, characterized by different spatial and time scales. The slow and spatially localized channel is associated with the Cu center of Azurin and the fast delocalized one with the protein's polypeptide matrix. Transport via the slow channel is by a sequential (noncoherent) process and in the second one by direct, off-resonant tunneling. (2) The two channels are capacitively coupled. Thus, with a change in charge occupation of the weakly coupled (metal center) channel, the broad energy level manifold, responsible for off-resonance tunneling, shifts, relative to the electrodes' Fermi levels. In this process, the off-resonance (fast) channel dominates transport, and the slow (redox) channel, while contributing only negligibly directly, significantly affects transport by intramolecular gating.

Thermal Exfoliation and Phosphorus Doping in Graphitic Carbon Nitride for Efficient Photocatalytic Hydrogen Production.

Photocatalytic H2 evolution has been regarded as a promising technology to alleviate the energy crisis. Designing graphitic carbon nitride materials with a large surface area, short diffusion paths for electrons, and more exposed reactive sites are beneficial for hydrogen evolution. In this study, a facile method was proposed to dope P into a graphitic carbon nitride framework by calcining melamine with 2-aminoethylphosphonic acid. Meanwhile, PCN nanosheets (PCNSs) were obtained through a thermal exfoliation strategy. Under visible light, the PCNS sample displayed a hydrogen evolution rate of 700 μmol·g-1·h-1, which was 43.8-fold higher than that of pure g-C3N4. In addition, the PCNS photocatalyst also displayed good photostability for four consecutive cycles, with a total reaction time of 12 h. Its outstanding photocatalytic performance was attributed to the higher surface area exposing more reactive sites and the enlarged band edge for photoreduction potentials. This work provides a facile strategy to regulate catalytic structures, which may attract great research interest in the field of catalysis.

Time-domain interferometry of electron weak localization through terahertz nonlinear response

We study theoretically the nonlinear optical response of disordered electrons in the regime of weak (anti)localization. Our analytical and numerical calculations reveal that in orthogonal/symplectic class systems, two consecutive, phase-coherent optical pulses generate an electric current echo that appears after the second pulse, and at a time equal to the pulse delay time. The current echo reflects the quantum interference between a self-intersecting electron path and its time-reversal partner, and, therefore, provides a time-domain interferometry of weak (anti)localization. Our results can be potentially tested on disordered metal films by using terahertz two-dimensional coherent spectroscopy or ultrafast transport measurements. Published by the American Physical Society 2024

A Detailed Survey of the Parallel Mean Free Path of Solar Energetic Particle Protons and Electrons

In this work, more than a dozen solar energetic particle (SEP) events are identified where the source region is magnetically well connected to at least one spacecraft at 1 au. The observed intensity–time profiles, for all available proton and electron energy channels, are compared to results computed using a numerical one-dimensional SEP transport model in order to derive the parallel mean free paths (pMFPs) as a function of energy (or rigidity) at 1 au. These inversion results are then compared to theoretical estimates of the pMFP, using observed turbulence quantities with observationally motivated variations as input. For protons, a very good comparison between inversion and theoretical results is obtained. It is shown that the observed inter-event variations in the inversion pMFP values can be explained by natural variations in the background turbulence values. For electrons, there is relatively good agreement with pMFPs derived assuming the damping model of dynamical turbulence, although the theoretical values are extremely sensitive to the details of the turbulence dissipation range, which themselves display a high level of variation.

Multi-layered carbon accommodation of MnO2 enabling fast kinetics for highly stable zinc ion batteries

Large-scale durable aqueous zinc ion batteries for stationary storage are realized by spray-coating conductive PEDOT(Poly(3,4-ethylenedioxythiophene)) wrapping MnO2/carbon microspheres hybrid cathode in this work. The porous carbon microspheres with multiple layers deriving from sucrose provide suitable accommodation for MnO2 active materials, exposing more redox active sites and enhancing the contact surface between electrolyte and active materials. As a result, MnO2/microspheres are adhered to the current collector by a conductive PEDOT coating without any binder. The ternary design retards the structural degradation during cycling and shortens the electron and ion transport path, rendering the full batteries high capacity and long cycle stability. The resulting batteries perform the capacity of 277, 227, 110, 85 and 50 mAh/g at 0.2, 0.5, 1, 2 and 5 A/g, respectively. After 3000 cycles the initial capacity retains 86%, and 80% after 5000 cycles. GITT indicates PEDOT wrapping MnO2/microspheres cathode enables better ion intercalating kinetics than conventional MnO2. The work could represent a novel and significant step forward in the studies on the large-scale application of zinc ion batteries.

Energy-Resolving Time-of-Flight Mass Spectrometry for Bulk Plasma Analysis.

This work presents a newly designed energy-resolving time-of-flight mass spectrometer (E-TOFMS) for analysing the energy and mass of ions in bulk plasma. The system comprises an electrostatic sector analyser (ESA) for energy-to-charge (E/Q) ratio resolution and an orthogonal reflectron TOFMS for mass-to-charge (m/Q) ratio analysis. The design choices are explained, providing insight into electron and ion path simulations. The instrument was characterised using various ion generation sources, including an electron impact ion source, high power impulse magnetron sputtering, and microwave plasma electron cyclotron resonance sources. To validate its functionality, the energy-resolving data was compared with data obtained under the same conditions using a Langmuir probe and a retarding field energy analyser (RFEA). The benefits of the proposed E-TOFMS were demonstrated by sputtering highly alloyed steel with multiple isotope-rich elements, such as Mo or W. This technique offers an E/Q ratio resolution of up to 0.15 V for a range up to 125 V and a m/Q ratio resolution of at least 700 Th for a range up to 250 Th, with a temporal resolution of 10 μs.