Passive Cavity Aerosol Spectrometer Probe Research Articles

Wildfire Smoke Observations in the Western United States from the Airborne Wyoming Cloud Lidar during the BB-FLUX Project. Part II: Vertical Structure and Plume Injection Height

Abstract The western U.S. wildfire smoke plumes observed by the upward-pointing Wyoming Cloud Lidar (WCL) during the Biomass Burning Fluxes of Trace Gases and Aerosols (BB-FLUX) project are investigated in a two-part paper. Part II here presents the reconstructed vertical structures of seven plumes from airborne WCL measurements. The vertical structures evident in the fire plume cross sections, supported by in situ measurements, showed that the fire plumes had distinct macrophysical and microphysical properties, which are closely related to the plume transport, fire emission intensity, and thermodynamic structure in the boundary layer. All plumes had an injection layer between 2.8 and 4.0 km above mean sea level, which is generally below the identified boundary layer top height. Plumes that transported upward out of the boundary layer, such as the Rabbit Foot and Pole Creek fires, formed a higher plume at around 5.5 km. The largest and highest Pole Creek fire plume was transported farthest and was sampled by University of Wyoming King Air aircraft at 170 km, or 2.3 h, downwind. It was associated with the warmest, driest, deepest boundary layer and the highest wind speed and turbulence. The Watson Creek fire plume intensified in the afternoon with stronger CO emission and larger smoke plume height than in the morning, indicating a fire diurnal cycle, but some fire plumes did not intensify in the afternoon. There were pockets of relatively large irregular aerosol particles at the tops of plumes from active fires. In less-active fire plumes, the WCL depolarization ratio and passive cavity aerosol spectrometer probe mass mean diameter maximized at a height that was low in the plume.

Below‐cloud scavenging of fine and coarse aerosol particles by rain: The role of raindrop size

Below‐cloud aerosol scavenging is an important process to remove particles from the atmosphere. In this study, both precipitation (measured with a laser disdrometer registering drops between 0.125 and 8 mm) and atmospheric aerosol particles (measured with a Passive Cavity Aerosol Spectrometer Probe registering aerosol sizes between 0.1 and 24 µm) have been sampled on a 1 min basis. Based on 6 months of outdoor measurements in León (northwest Iberian Peninsula), the scavenging coefficients were calculated for the aerosol particles measured, with a mean value of 2.6 × 10−5 ± 6.0 × 10−5 s−1 for the fine mode and 5.8 × 10−5 ± 9.6 × 10−5 s−1 for the coarse mode in 54 rain events. Likewise, the particle concentration decreased during rain by 10%, and by 18% between the time before and after the rain. In the Greenfield Gap (sizes between 0.3 and 1 µm) the scavenging is less effective, mainly between 0.6 and 1 µm, than with smaller particles. The number of drops between 0.75 and 3 mm shows statistically significant (p < 0.05) negative correlations with the number of particles between 0.16 and 1.76 µm, thus illustrating the potential of those raindrops to favour the scavenging of particles of that size. In addition, there were statistically significant negative correlations between the total volume removed by falling drops (mm3/m3) and the variation of the number of particles in channels with diameters between 0.12 and 0.19 µm.

On the parametrization of optical particle counter response including instrument-induced broadening of size spectra and a self-consistent evaluation of calibration measurements

Abstract. Optical particle counters (OPCs) are common tools for the in situ measurement of aerosol particle number size distributions. As the actual quantity measured by OPCs is the intensity of light scattered by individual particles, it is necessary to translate the distribution of detected scattering signals into the desired information, i.e., the distribution of particle sizes. A crucial part in this challenge is the modeling of OPC response and the calibration of the instrument – in other words, establishing the relation between instrument-specific particle scattering cross-section and measured signal amplitude. To date, existing methods lack a comprehensive parametrization of OPC response, particularly regarding the instrument-induced broadening of signal amplitude distributions. This deficiency can lead to significant size distribution biases. We introduce an advanced OPC response model including a simple parametrization of the broadening effect and a self-consistent way to evaluate calibration measurements using a Markov chain Monte Carlo (MCMC) method. We further outline how to consistently derive particle number size distributions with realistic uncertainty estimates within this new framework. Based on measurements of particle standards for two OPCs, the Grimm model 1.129 (SkyOPC) and the DMT Passive Cavity Aerosol Spectrometer Probe (PCASP), we demonstrate that residuals between measured and modeled response can be substantially reduced when using the new approach instead of existing methods. More importantly, for the investigated set of measurements only the new approach yields results that conform with the true size distributions within the range of model uncertainty. The presented innovations will help improving the accuracy of OPC-derived size distributions and the assessment of their precision.

Validation of LIRIC aerosol concentration retrievals using airborne measurements during a biomass burning episode over Athens

In this paper we validate the Lidar-Radiometer Inversion Code (LIRIC) retrievals of the aerosol concentration in the fine mode, using the airborne aerosol chemical composition dataset obtained over the Greater Athens Area (GAA) in Greece, during the ACEMED campaign. The study focuses on the 2nd of September 2011, when a long-range transported smoke layer was observed in the free troposphere over Greece, in the height range from 2 to 3km. CIMEL sun-photometric measurements revealed high AOD (~0.4 at 532nm) and Ångström exponent values (~ 1.7 at 440/870nm), in agreement with coincident ground-based lidar observations. Airborne chemical composition measurements performed over the GAA, revealed increased CO volume concentration (~ 110ppbv), with 57% sulphate dominance in the PM1 fraction. For this case, we compare LIRIC retrievals of the aerosol concentration in the fine mode with the airborne Aerosol Mass Spectrometer (AMS) and Passive Cavity Aerosol Spectrometer Probe (PCASP) measurements. Our analysis shows that the remote sensing retrievals are in a good agreement with the measured airborne in-situ data from 2 to 4km. The discrepancies observed between LIRIC and airborne measurements at the lower troposphere (below 2km), could be explained by the spatial and temporal variability of the aerosol load within the area where the airborne data were averaged along with the different time windows of the retrievals.

Optical, physical, and chemical properties of springtime aerosol over Barrow Alaska in 2008

Airborne observations from four flights during the 2008 Indirect and Semi-Direct Aerosol Campaign (ISDAC) are used to examine some cloud-free optical, physical, and chemical properties of aerosol particles in the springtime Arctic troposphere. The number concentrations of particles larger than 0.12 µm (Na>120), important for light extinction and cloud droplet formation, ranged from 15 to 2260 cm−3, with the higher Na>120 cases dominated by measurements from two flights of long-range transported biomass burning (BB) aerosols. The two other flights examined here document a relatively clean aerosol and an Arctic Haze aerosol impacted by larger particles largely composed of dust. For observations from the cleaner case and the BB cases, the particle light scattering coefficients at low relative humidity (RH<20%) increased nonlinearly with increasing Na>120, driven mostly by an increase in mean sizes of particles with increasing Na>120 (BB cases). For those three cases, particle light absorption coefficients also increased nonlinearly with increasing Na>120 and linearly with increasing submicron particle volume concentration. In addition to black carbon, brown carbon was estimated to have increased light absorption coefficients by 27% (450 nm wavelength) and 14% (550 nm) in the BB cases. For the case with strong dust influence, the absorption relative to submicron particle volume was small compared with the other cases. There was a slight gradient of Passive Cavity Aerosol Spectrometer Probe (PCASP) mean volume diameter (MVD) towards smaller sizes with increasing height, which suggests more scavenging of the more elevated particles, consistent with a typically longer lifetime of particles higher in the atmosphere. However, in approximately 10% of the cases, the MVD increased (>0.4 µm) with increasing altitude, suggesting transport of larger fine particle mass (possibly coarse particle mass) at high levels over the Arctic. This may be because of transport of larger particles at higher elevations and relatively slow deposition to the surface.

Calibration of the passive cavity aerosol spectrometer probe for airborne determination of the size distribution

Abstract. This work describes calibration methods for the particle sizing and particle concentration systems of the passive cavity aerosol spectrometer probe (PCASP). Laboratory calibrations conducted over six years, in support of the deployment of a PCASP on a cloud physics research aircraft, are analyzed. Instead of using the many calibration sizes recommended by the PCASP manufacturer, a relationship between particle diameter and scattered light intensity is established using three sizes of mobility-selected polystyrene latex particles, one for each amplifier gain stage. In addition, studies of two factors influencing the PCASP's determination of the particle size distribution – amplifier baseline and particle shape – are conducted. It is shown that the PCASP-derived size distribution is sensitive to adjustments of the sizing system's baseline voltage, and that for aggregates of spheres, a PCASP-derived particle size and a sphere-equivalent particle size agree within uncertainty dictated by the PCASP's sizing resolution. Robust determinations of aerosol concentration, and size distribution, also require calibration of the PCASP's aerosol flowrate sensor. Sensor calibrations, calibration drift, and the sensor's non-linear response are documented.

The lofting of Western Pacific regional aerosol by island thermodynamics as observed around Borneo

Abstract. Vertical profiles of aerosol chemical composition, number concentration and size were measured throughout the lower troposphere of Borneo, a large tropical island in the western Pacific Ocean. Aerosol composition, size and number concentration measurements (using an Aerodyne Aerosol Mass Spectrometer, Passive Cavity Aerosol Spectrometer Probe and Condensation Particle Counter, respectively) were made both upwind and downwind of Borneo, as well as over the island itself, on board the UK BAe-146 research aircraft as part of the OP3 project. Two meteorological regimes were identified – one dominated by isolated terrestrial convection (ITC) which peaked in the afternoon, and the other characterised by more regionally active mesoscale convective systems (MCS). Upwind profiles show aerosol to be confined to a shallow marine boundary layer below 930 ± 10 hPa (~760 m above sea level, a.s.l.). As this air mass advects over the island with the mean free troposphere synoptic flow during the ITC-dominated regime, it is convectively lofted above the terrestrial surface mixed layer to heights of between 945 ± 22 (~630 m a.s.l.) and 740 ± 44 hPa (~2740 m a.s.l.), consistent with a coupling between the synoptic steering level flow and island sea breeze circulations. Terrestrial aerosol was observed to be lofted into this higher layer through both moist convective uplift and transport through turbulent diurnal sea-breeze cells. At the peak of convective activity in the mid-afternoons, organic aerosol loadings in the lofted layer were observed to be substantially higher than in the morning (by a mean factor of three). This organic matter is dominated by secondary aerosol from processing of biogenic gas phase precursors. Aerosol number concentration profiles suggest formation of new particles aloft in the atmosphere. By the time the air mass reaches the west coast of the island, terrestrial aerosol is enhanced in the lofted layer. Such uplift of aerosol in Borneo is expected to increase aerosol lifetimes in the lower free troposphere downwind, as they are above the boundary layer and therefore less likely to be lost by wet or dry deposition. It is also likely to change the role they play in the semi-direct and direct aerosol effects. The long chain of islands extending from Malaysia to Australia may all similarly be expected to present an orographic barrier to low level mean flow. This would lead to significant transport of aerosol into the tropical free troposphere across the Western Pacific region.

Particle sizing calibration with refractive index correction for light scattering optical particle counters and impacts upon PCASP and CDP data collected during the Fennec campaign

Abstract. Optical particle counters (OPCs) are used regularly for atmospheric research, measuring particle scattering cross sections to generate particle size distribution histograms. This manuscript presents two methods for calibrating OPCs with case studies based on a Passive Cavity Aerosol Spectrometer Probe (PCASP) and a Cloud Droplet Probe (CDP), both of which are operated on the Facility for Airborne Atmospheric Measurements BAe-146 research aircraft. A probability density function based method is provided for modification of the OPC bin boundaries when the scattering properties of measured particles are different to those of the calibration particles due to differences in refractive index or shape. This method provides mean diameters and widths for OPC bins based upon Mie-Lorenz theory or any other particle scattering theory, without the need for smoothing, despite the highly nonlinear and non-monotonic relationship between particle size and scattering cross section. By calibrating an OPC in terms of its scattering cross section the optical properties correction can be applied with minimal information loss, and performing correction in this manner provides traceable and transparent uncertainty propagation throughout the whole process. Analysis of multiple calibrations has shown that for the PCASP the bin centres differ by up to 30% from the manufacturer's nominal values and can change by up to approximately 20% when routine maintenance is performed. The CDP has been found to be less sensitive than the manufacturer's specification with differences in sizing of between 1.6 ± 0.8 μm and 4.7 ± 1.8 μm for one flight. Over the course of the Fennec project in the Sahara the variability of calibration was less than the calibration uncertainty in 6 out of 7 calibrations performed. As would be expected from Mie-Lorenz theory, the impact of the refractive index corrections has been found to be largest for absorbing materials and the impact on Saharan dust measurements made as part of the Fennec project has been found to be up to a factor of 3 for the largest particles measured by CDP with diameters of approximately 120 μm. In an example case, using the calibration and refractive index corrections presented in this work allowed Saharan dust measurement from the PCASP, CDP and a Cloud Imaging Probe to agree within the uncertainty of the calibration. The agreement when using only the manufacturer's specification was poor. Software tools have been developed to perform these calibrations and corrections and are now available as open source resources for the community via the SourceForge repository.

Spatial and temporal variability of aerosol particles in Arctic spring

AbstractThe objective of this work is to investigate the variability in the aerosol particle number concentration in Arctic spring. The Indirect and Semi‐Direct Aerosol Campaign (ISDAC) was conducted during April 2008 in the vicinities of Fairbanks and Barrow, Alaska. Aircraft‐based measurements of total aerosol particle number concentration (Na) in the size range of 0.12–3 µm diameter were obtained using a passive cavity aerosol spectrometer probe (PCASP‐100X). The analysis considers Na during cloud‐free periods in biomass burning (BB) and non‐BB aerosol loading scenarios, the latter including background cases and cases with elevated concentration in layers. The BB cases had air masses originating mainly from Russian and Asian forest and crop fires, whereas the non‐BB cases originated predominantly from Arctic or oceanic regions. The average Na for all non‐BB cases was 127 cm−3, while that for all BB cases was Na = 720 cm−3. These estimates do not, however, capture the details of aerosol particle layers encountered during most flights. Variability in Na was considered for constant altitude (horizontal) flight legs ranging from 50 to 650 km in length, as well as for vertical flight profiles up to 7 km above sea level. When aerosol particle layers were encountered, Na rapidly increased from 20 to 550 cm−3, and reached up to 2200 cm−3 within air masses dominated by BB plumes. The observed variability in Na may have important implications for estimating cloud microphysical properties as well as estimates of particle properties used in global climate model simulations, because averaging over large space‐ or time‐scales may not represent real atmospheric conditions. The analysis demonstrates the difficulty in interpreting average aerosol particle characteristics along longer flight legs, particularly during cases with higher particle loading that varies over shorter distance scales and time periods. Copyright © 2012 Royal Meteorological Society and Crown in the right of Canada.

Estimates of aqueous-phase sulfate production from tandem differential mobility analysis

Abstract During June and July of 2004, airborne measurements of size-resolved aerosol properties were made over the coastal Pacific near Marina, California. Tandem differential mobility analysis was used to determine the hygroscopic properties of these aerosols and, subsequently, to examine the change in soluble mass after the aerosol had been cloud-processed. Three of the eight cases analyzed during the field campaign exhibited increased soluble mass attributable to cloud-processing. The calculated change in soluble mass after cloud-processing, derived from measurements made below and above cloud, ranged from 1.08 ϒ g m−3 to 1.40 ϒ g m−3. These values are in agreement with those determined using data collected during previous field studies in the same region. Aerosol size distributions measured throughout the study with a Passive Cavity Aerosol Spectrometer Probe were averaged to create a single representative distribution, which was used to examine the impact of the addition of sulfate to a typical aerosol measured during this project. Mass light-scattering efficiencies were calculated for both the initial and cloud-processed size distributions using Mie-Lorenz theory. These calculations show that the increase in mass light-scattering efficiency following passage through a single non-precipitating cloud to be 14%, which is in agreement with findings of previous studies in the same region. This new technique produces results that are consistent with existing methods for measuring in-cloud sulfate production and has the advantage of intrinsic consistency with the hygroscopicity and CCN activity of the aerosol.

Aerosol size distribution in precipitation events in León, Spain

Precipitation and continuous particle number size distributions have been measured using a passive cavity aerosol spectrometer probe PCASP-X, in an urban environment: the city of León, Spain. Five rain events have been analyzed in detail, none of which registered very intense precipitation, ranging from 2.5 mm to 14.7 mm, with a maximum rain intensity of 5.6 mm/h. The study focuses on the influence of precipitation in aerosol size distributions before, during and after a rain event. Washout effects have been observed during rain events with intensities of over 3.2 ± 1.5 mm/h, resulting in a decrease of 20% in the number of particles detected, the decrease affecting large and small particles alike. However, if the rain intensity is about 0.6 mm/h or lower, the result is a considerable increase in the number of aerosols measured — up to 89% more — with an increase in the number of particles smaller than 1.3 µm and a decrease in the number of particles larger than 1.3 µm. It may be the case that during very weak rain intensity the probe does not discriminate adequately between aerosols and small precipitating droplets or the extremely small droplets that remain in suspension in the atmosphere. In consequence, it will be argued that measurements taken during very weak rain events (with an intensity of less than 0.6 mm/h), such as drizzle or dense fog, should be treated separately or not be considered. The performance of the accumulation and coarse modes has also been studied, as well as the count median diameters (CMDs) before, during and after the rain event.

Evaluation of a unified regional air-quality modeling system (AURAMS) using PrAIRie2005 field study data: The effects of emissions data accuracy on particle sulphate predictions

The effects of the accuracy of major-point source emissions input data on the predictions of a regional air-quality model (AURAMS) were investigated through a series of scenario simulations. The model domain and time period were chosen to correspond to that of PrAIRie2005, an air-quality field study with airborne and ground-based mobile measurement platforms that took place between August 12th and September 7th, 2005, over the city of Edmonton, Alberta, Canada. The emissions data from standard sources for three coal-fired power-plants located west (typically upwind) of the city were compared to the continuous emissions monitoring system (CEMS) taking place at the time of the study – the latter showed that the original emissions inventory data considerably overestimated NO x , SO 2, and primary particulate emissions during the study period. Further field investigation (stack sampling) in the fall of 2006 showed that the measured primary particle size distribution and chemical speciation for the emissions were strikingly different from the distribution and speciation originally used in the model. The measured emissions were used to scale existing emissions data in accord with the CEMS and in-stack measurements. The effects of these improvements to the emissions data were examined sequentially in nested AURAMS simulations (finest horizontal resolution 3 km), and were compared to airborne aerosol mass spectrometer (Aerodyne AMS) measurements of particle sulphate, and particle distributions from an airborne passive cavity aerosol spectrometer probe (PCASP). The emissions of SO 2 had the greatest impact on predicted PM 1 sulphate, while the primary particle size distribution and chemical speciation had a smaller role. The revised emissions data greatly improved the comparisons between observations and model values, though over-predictions of fine-mode sulphate still occur near the power-plants, with the use of the revised emissions data. The modified emissions also had a significant impact on the larger particles of the particulate matter, with more primary PM in sizes greater than 1 μm diameter than had previously been estimated, and higher large particle concentrations close to the power-plants.

Performance characteristics of the ultra high sensitivity aerosol spectrometer for particles between 55 and 800 nm: Laboratory and field studies

A new optical particle counter, the Particle Metrics, Inc., ultra high sensitive aerosol spectrometer (UHSAS), has been used to size aerosol particles both in our laboratory, and at a remote mountain-top site in Wyoming. The laboratory studies show that the UHSAS measured diameters of polystyrene latex (PSL), ammonium sulfate, and ammonium nitrate particles are within 10% of those determined by a scanning mobility particle sizer (SMPS), as are those for non-spherical sodium chloride particles and PSL doublets. The UHSAS detection efficiency is close to 100% for particles larger than 100 nm and concentrations below 3000 cm - 3 , but decreases both for smaller particles and for higher concentrations considerably. The field measurements confirm these observations and also demonstrate good agreement of particle concentration measurements between the UHSAS, SMPS, and a passive cavity aerosol spectrometer probe (PCASP) in the same size ranges.

Inversion of data containing information on the aerosol particle size distribution using multiple instruments

An algorithm for inversion of data containing information on particle size distributions is presented that is designed to be true to the input data, does not need an initial guess, does not assume a shape of the size distribution function, yields the smoothest non-negative result consistent with the input data, calculates the uncertainty of the result based on the uncertainty of the input data, and is capable of combining data from more than one instrument type into one inversion result. To test the algorithm, synthetic data of aircraft payloads sensitive for particle diameters D p < 0.2 μ m and combining a cascade of condensation particle counters (CPSA) with a differential mobility analyser (DMA), a passive cavity aerosol spectrometer probe (PCASP), and a parallel diffusion battery (PDB) are generated. The CPSA/DMA instrument combination retrieves the log-normal parameters of the Aitken-mode ( 0.01 μ m < D p < 0.2 μ m ) with < 1 % uncertainty while the CPSA/PDB combination reaches ∼ 4 % and the CPSA/PCASP combination ∼ 8 % uncertainty. Compared with the CPSA/DMA set-up, the CPSA/PDB and CPSA/PCASP combinations have advantages with respect to temporal resolution and space/weight demands, respectively. The algorithm is extendable to other instrument types and may also serve as a tool for optimising instruments or instrument packages with respect to specific scientific questions.

Combustion aerosol from experimental crown fires in a boreal forest jack pine stand

Combustion aerosol particles from boreal forest fires were quantified to facilitate investigation of the potential effects of increased fire activity caused by global warming, by providing data inputs for global and regional climate modelling of the direct and indirect effects. Aerial sampling was carried out in smoke plumes from 1-ha prescribed burns in mature jack pine stands. The three sampled burns resulted in crown fires, with fuel consumption from 4.2 to 5.8 kg·m–2. Accumulation and coarse mode aerosol (&gt;0.1 µm) was quantified using a passive cavity aerosol spectrometer probe and cascade impactor. The number median diameter of particles in the smoke plume was 0.29 µm, and the peak number and cross-sectional area density occurred around a particle size of 0.4 µm. More than 99% of particles sized had diameters &lt;1.2 µm. Aerosol from flaming combustion was coarser than that from the smouldering phase, with number median diameters of 0.3 and 0.2 µm, respectively.

Comparison of aerosol size distributions, radiative properties, and optical depths determined by aircraft observations and Sun photometers during SAFARI 2000

The Meteorological Office C‐130 aircraft performed a dedicated flight over the Etosha Pan surface‐based Aerosol Robotic Network (AERONET) Sun photometer site on 13 September 2000 during the Southern African Aerosol Regional Science Initiative (SAFARI 2000) intensive measurement campaign. Aerosol optical depths at different wavelengths, τaerλ, are derived from in situ measurements of the scattering and absorption coefficients and from various radiometric measurements and compared to those derived from the Sun photometer site. The estimates of τaerλ from the various measurements are shown to be in good agreement. The exception to this is when τaerλ is derived from the Passive Cavity Aerosol Spectrometer Probe (PCASP), as this method is shown to be extremely sensitive to the pitch angle of the aircraft; therefore, τaerλ differs for profile ascents and profile descents. However, the aerosol size distribution measured by the PCASP and derived from the AERONET site are in excellent agreement over the 0.05–1.0 μm radius range, which contains the majority of the optically active particles. C‐130‐derived refractive indices and single scattering albedos are also shown to be in excellent agreement with those derived from the AERONET site. The consistency between in situ and remotely sensed data suggests that, for aerosol well mixed in the vertical, data from AERONET may be used with confidence in validating satellite measurements and modeling studies of the radiative properties and effects of aerosols.

Evolution of boundary-layer aerosol particles due to in-cloud chemical reactions during the 2nd Lagrangian experiment of ACE-2

The second Aerosol Characterisation Experiment (ACE-2) was aimed at investigating the physical, chemical and radiative properties of aerosol and their evolution in the North Atlantic region. In the 2nd “Lagrangian” experiment, an air mass was tracked over a 30-h period during conditions of extensive stratocumulus cover. Boundary-layer measurements of the aerosol size distribution obtained with a passive cavity aerosol spectrometer probe (PCASP) during the experiment show a gradual growth in size of particles in the 0.1–0.2 μm diameter mode. Simultaneously, SO 2 concentrations were found to decrease sharply from 800 to 20 ppt. The fraction of sulphate in aerosol ionic mass increased from 0.68±0.07 to 0.82±0.09 for small particles (diameter below 1.7 μm) and from 0.21±0.04 to 0.34±0.03 for large particles (diameter above 1.7 μm). The measurements were compared with a multicyclic parcel model of gas phase diffusion into cloud droplets and aqueous phase chemical reactions. The model was able to broadly reproduce the observed transformation in the aerosol spectra and the timescale for the transformation of SO 2 to sulphate aerosol. The modelled SO 2 concentration in the boundary layer fell to below half its initial value over a 6.5-h time period due to a combination of the entrainment of cleaner tropospheric air and cloud chemical reactions. NH 3 and HCl gas were also found to play an important role in cloud processing in the model. DOI: 10.1034/j.1600-0889.2000.00037.x

Evolution of boundary-layer aerosol particles due to in-cloud chemical reactions during the 2nd Lagrangian experiment of ACE-2

The second Aerosol Characterisation Experiment (ACE-2) was aimed at investigating the physical, chemical and radiative properties of aerosol and their evolution in the North Atlantic region. In the 2nd “Lagrangian” experiment, an air mass was tracked over a 30-h period during conditions of extensive stratocumulus cover. Boundary-layer measurements of the aerosol size distribution obtained with a passive cavity aerosol spectrometer probe (PCASP) during the experiment show a gradual growth in size of particles in the 0.1−0.2 μm diameter mode. Simultaneously, SO2 concentrations were found to decrease sharply from 800 to 20 ppt. The fraction of sulphate in aerosol ionic mass increased from 0.68±0.07 to 0.82±0.09 for small particles (diameter below 1.7 μm) and from 0.21±0.04 to 0.34±0.03 for large particles (diameter above 1.7 μm). The measurements were compared with a multicyclic parcel model of gas phase diffusion into cloud droplets and aqueous phase chemical reactions. The model was able to broadly reproduce the observed transformation in the aerosol spectra and the timescale for the transformation of SO2 to sulphate aerosol. The modelled SO2 concentration in the boundary layer fell to below half its initial value over a 6.5-h time period due to a combination of the entrainment of cleaner tropospheric air and cloud chemical reactions. NH3 and HCl gas were also found to play an important rôle in cloud processing in the model.

Raman lidar measurements of aerosol extinction and backscattering: 2. Derivation of aerosol real refractive index, single‐scattering albedo, and humidification factor using Raman lidar and aircraft size distribution measurements

Aerosol backscattering and extinction profiles measured by the NASA Goddard Space Flight Center Scanning Raman Lidar (SRL) during the remote cloud sensing (RCS) intensive operations period (IOP) at the Department of Energy Atmospheric Radiation Measurement (ARM) southern Great Plains (SGP) site during two nights in April 1994 are discussed. These profiles are shown to be consistent with the simultaneous aerosol size distribution measurements made by a PCASP (Passive Cavity Aerosol Spectrometer Probe) optical particle counter flown on the University of North Dakota Citation aircraft. We describe a technique which uses both lidar and PCASP measurements to derive the dependence of particle size on relative humidity, the aerosol real refractive index n, and estimate the effective single‐scattering albedo ω0. Values of n ranged between 1.4–1.5 (dry) and 1.37–1.47 (wet); ω0 varied between 0.7 and 1.0. The single‐scattering albedo derived from this technique is sensitive to the manner in which absorbing particles are represented in the aerosol mixture; representing the absorbing particles as an internal mixture rather than the external mixture assumed here results in generally higher values of ω0. The lidar measurements indicate that the change in particle size with relative humidity as measured by the PCASP can be represented in the form discussed by Hanel [1976] with the exponent γ = 0.3 ± 0.05. The variations in aerosol optical and physical characteristics captured in the lidar and aircraft size distribution measurements are discussed in the context of the meteorological conditions observed during the experiment.

Response of Particle Measuring Systems Airborne ASASP and PCASP to NaCl and Latex Particles

The response of a Particle Measuring Systems, Inc. (PMS) airborne Passive Cavity Aerosol Spectrometer Probe (PCASP)-100X and a PMS airborne Active Scattering Aerosol Spectrometer Probe (ASASP)-100X to nearly monodisperse aerosols of NaCl and polystyrene latex spheres in the size range 0.074–1.07 μm diameter (± 5%) are examined. Particles < 0.34 μm are size classified by electrical mobility using a Thermo System Inc. Electrostatic Classifier. The particles are also sized with the aid of a scanning electron microscope. Three equivalent diameters for the near cubic NaCl particles are considered: average of length and breadth, and cross section equivalent and volume equivalent diameters. For the linear diameter, the probes' response to latex and NaCl particles is quite similar. However, the use of cross section and volume equivalent diameter leads NaCl to be sized significantly less than the latex spheres consistent with reported differences between spherical (i.e., latex) and cubical geometry (i.e., NaCl). U...