Aggregation Of Particles Research Articles

Effect of pyrite on the treatment of chlorophenolic compounds with zero-valent iron-Fenton process under uncontrolled pH conditions: reaction mechanism and biodegradability.

This current study explored the effect of pyrite on the treatment of chlorophenolic compounds (CP) by Fenton process with micron-sized zero-valent iron (ZVI) as the catalyst. The experiments were conducted in batch reactors with 100mg L-1 CP, 0-0.02M H2O2, and variable pyrite and ZVI doses (0-1g L-1). Our findings show that while the reactor with 1g L-1 ZVI as the only catalyst achieved only 10% CP removal efficiency due to rapid ZVI surface passivation and ZVI particle aggregation, the CP removal efficiency increased with increasing pyrite dose and reached 100% within couple of minutes in reactors with 0.8g L-1 pyrite and 0.2g L-1 ZVI. The CP removal was mainly driven by the oxidative treatment of CPs with some strong radicals such as hydroxyl radicals (•OH) while the adsorption onto the catalyst surface was only responsible for 10 to 25% of CP removals, depending on the type of CP studied. The positive impact of pyrite on CP removal by the ZVI/H2O2 system could be attributed to the ability of pyrite to (1) create an acidic environment for optimum Fenton process, (2) provide support material for ZVI to minimize ZVI particle agglomeration, and (3) stimulate iron redox cycling for improved surface site generation. Following oxidative Fenton treatment, the degradation intermediate products of CPs, including some aromatic compounds (benzoquinone, hydroquinone, etc.) and organic acids (e.g., acetic acid), became more biodegradable in comparison to their mother compounds. Overall, the treatment systems with a mixture of ZVI and pyrite as catalyst materials could offer a suitable cost-effective technology for the treatment of wastewater containing biologically non- or low-degradable toxic compounds such as chlorophenols.

Experimental Investigation and Numerical Analysis Regarding the Influence of Cutting Parameters on the Asphalt Milling Process

Abrasion wear is a significant concern for cutting tools, particularly when milling asphalt concrete due to the presence of hard mineral aggregate particles. The pressure exerted on the cutting tool by the chipped material and the resulting cutting forces directly influence tool wear. To estimate the cutting forces in asphalt milling, the authors propose using either laboratory experiments or cost-effective Discrete Element Method (DEM) modeling—by simulating the real conditions—as direct measurement under real conditions is challenging. This article presents results from an original experimental program aimed at determining the cutting forces during asphalt pavement milling. A specialized stand equipped with a moving plate and recording devices was designed to vary milling depth, rotational speed, and advance speed. The experimental results for horizontal force values were compared with numerical results from DEM modeling. It was found that both increasing the milling depth and the advance speed lead to higher cutting forces. Generally, DEM modeling trends align with experimental results, although DEM values are generally higher. The statistical analysis allowed identification of the milling depth as the most significant parameter influencing cutting force and the optimal combination of milling parameters to achieve minimum horizontal force acting on cutting tooth, namely, 15 mm milling depth and 190 mm/min advanced speed.

Research on the enhancement material and culture method of soil aggregates composed of feldspathic sandstone and sand

The Mu Us Sandy Land is a region characterized by wind-blown sand and soil erosion in northern China. To enhance the soil quality of this area, various organic materials were incorporated into the mixed soil at a volume ratio of 1:2 for feldspathic sandstone to sand. Culture was conducted in the field and under constant temperature conditions in laboratory culture chambers. Four treatments were established in the experiment, each calculated based on weight ratio and controlled (with no organic material added, CK); single application of straw (5% straw, P1); single application of biochar (5% biochar, P2); combined application of biochar and straw (5% biochar + 5% straw, P3). After 90 days of culture, soil samples were collected for analysis of various indicators such as soil aggregate particle size distribution, water stability of soil aggregates, mean weight diameter, mean geometric diameter, and fractal dimension using dry sieving and wet sieving methods. The objective is to establish a scientific basis and provide technical support for addressing the challenges associated with compound soil and implementing rational fertilization measures. The research results indicate that: (1) The quantity of aggregates > 0.25 mm under different treatments follows the order CK < P1 < P2 < P3, and the differences between treatments are significant (P < 0.05); (2) Soil water stability, mean weight diameter (MWD), mean geometric diameter (GMD), and fractal dimension of soil aggregates in compound soil with different organic material additions are superior to the control, and the effect of biochar on improving soil aggregates is better than that of corn straw. The combined application of both significantly improves the effect compared to single applications. In both culture modes, under wet sieving, the P3 treatment shows the highest MWD and GMD of soil aggregates, with an increase ranging from 3.45% to 85% and 4.55% to 38.46%, respectively, compared to other treatments. (3) The trend of fractal dimension among treatments is consistent: P3 < P2 < P1 < CK, and the differences between treatments are significant (P < 0.05). Moreover, there is a good negative correlation linear equation relationship between the fractal dimension (y) and WR > 0.25 (x) of compound soil, with a correlation coefficient of up to 0.9851. In conclusion, the incorporation of organic materials can effectively enhance the proportion of macroaggregates in compound soil consisting of Feldspathic sandstone and sand, thereby improving soil stability and erosion resistance. The optimal outcome is achieved through the combined application of biochar and straw. Indoor culture proves to be more effective than field culture, while wet sieving accurately reflects the structural characteristics of compound soil under both dry and wet sieving treatments.

Performance prediction and optimization of nanolubricants for hydrodynamic journal bearings: a data-driven approach for regulating volumetric fraction and aggregate particle size

Performance prediction and optimization of nanolubricants for hydrodynamic journal bearings: a data-driven approach for regulating volumetric fraction and aggregate particle size

The role of divertor pumping combined with full drifts in particle exhaust and divertor plasma

The effect of drifts combined with pumping on particle exhaust is assessed using the SOLPS-ITER code package, considering full drifts. Both drift and pumping speed S can affect particle exhaust. Drifts change the neutral density by influencing plasma flow and the resulting particle recycling. This leads to the accumulation of neutral particles either far away or close to the pump opening location. The particle exhaust is enhanced as S rises. When the pump opening is positioned at the common flux region (CFR) of the outer divertor (referred to as Pump CFR/OD), particle exhaust is suppressed by drifts in forward Bt , while it is enhanced by drifts in reversed Bt , with fixed S. On the other hand, when the pump is situated in the private flux region (PFR) of the OD (referred to as Pump PFR/OD), particle exhaust is enhanced by drifts in both reversed and forward Bt compared to the case without drifts. Moreover, the effective pumping in reversed Bt is stronger than in forward Bt . In the same Bt direction, Pump PFR/OD has a higher effective pumping than Pump CFR/OD. Increased S results in higher particle exhaust in all Bt direction and pump location cases. The plasma detachment is affected by drift, S and pump opening location, respectively. For the specified Bt direction and pump opening location case, higher S suppresses plasma detachment. For identical particle exhaust rates, stronger pumping capacity can promote plasma detachment. Therefore, Pump PFR/OD can more easily achieve OD detachment than Pump CFR/OD in the same Bt direction. Overall, placing the pump at the PFR side of the OD while running in reversed Bt is the best option from the divertor particle exhaust and plasma detachment point of view.

A Gold Nanoparticle-Based Cortisol Aptasensor for Non-Invasive Detection of Fish Stress

Cortisol is a key stress biomarker in humans and animals, including fishes. In aquafarming, stress monitoring using cortisol quantification can help to optimize aquaculture practices for welfare and productivity enhancement. However, most current methods for cortisol detection rely on invasive tissue sampling. In this work, we developed a gold nanoparticle (AuNP)-based cortisol sensor to address the demand of detecting picomolar ranges of cortisol from complex fish tank water matrices as a non-invasive alternative for more effective stress monitoring. We first identified a DNA aptamer with effective binding to cortisol and then conjugated the thiol-labelled aptamer to AuNPs together with a blocker molecule (CALNN) to form an Au-Apt-CALNN conjugate that is stable in fish tank water. The cortisol detection principle is based on magnesium chloride (MgCl2)-induced particle aggregation, where the cortisol-bound aptamer on the AuNPs folds into a tertiary structure and provides greater protection for Au-Apt-CALNN against MgCl2-induced aggregation due to steric stabilization. At an optimum MgCl2 concentration, the differential stability of particles with and without cortisol binding offers a limit of detection (LOD) of 100 pM for cortisol within a 35 min reaction. The aptasensor has been validated on recirculating aquaculture system (RAS) fish tank water samples by the HPLC method and was able to detect changes in water cortisol induced by two different stress paradigms. This on-site deployable and non-invasive sensor offers opportunities for more efficient and real-time fish stress monitoring for the optimization of aquaculture practices.

The Impact of Polyphosphates on the Colloidal Stability of Laponite Particles.

The effect of polyphosphate (polyP) adsorption on the colloidal properties of disc-shaped laponite (LRD) particles was examined in aqueous dispersions with a focus on elucidating the interparticle forces that govern the colloidal stability of the systems. The charge and aggregation rate data of bare LRD exhibited an ionic strength-dependent trend, confirming the presence of double-layer repulsion and van der Waals attraction as major surface interactions. The charge of LRD particles significantly increased in magnitude at elevated polyP concentrations as a result of polyP adsorption and subsequent overcharging of the positively charged sites on the edges of the LRD discs. A transition from stable to unstable LRD colloids was observed with increasing polyP doses indicating the formation of aggregates in the latter systems due to depletion forces and/or bridging interactions induced by dissolved or adsorbed polyP, respectively. The degree of phosphate polymerization influenced neither the charge nor the aggregation mechanism. The findings clearly confirm that polyP adsorption was the driving phenomenon to induce particle aggregation in contrast to other clay types, where phosphate derivatives act as dispersion stabilizing agents. This study provides valuable insights into the early stages of aggregation in colloidal systems involving LRD and polyPs, which have a crucial role in predicting further material properties that are important to designing LRD-polyP composites for applications such as potential phosphate sources in chemical fertilizers.

Development of new numerical approach to the flow and segregation behaviors of fresh concrete considering rebar restraint and its application in reinforced lightweight aggregate concrete

Although there are many studies on flow simulation methods for fresh concrete, there are very few studies on casting simulation of reinforced concrete, and in these studies the reinforcing bars are treated only as static boundaries without their restraining effect on the concrete flowing between them. In this study, we first developed a new numerical method based on the MPS method for simulating the flow and segregation behaviors of fresh concrete during casting reinforced member, considering the restraint of reinforcing bars by applying a normal stress to the concrete. Fresh concrete was treated as the double-phase granular fluid that follows a non-linear rheological model, and was represented by matrix mortar, and coarse aggregate particles with actual sizes and random shapes. Then, as an application of this numerical method, the flow and segregation behaviors of lightweight aggregate concrete (LWAC) in an L-shaped box with rebars were numerically investigated in addition to measurement. The comparison of the numerical and experimental results shows that this numerical method allows the LCA volume fraction to be calculated within 3 % error in predicting the segregation behavior of LCA in reinforced LWAC, and improves the accuracy of the flow simulation of LWAC by about 1.5 times. Furthermore, this numerical method can double the accuracy of concrete flow prediction, compared to treating the reinforcement as a static boundary.

Pressurized water reactor fuel corrosion-related unidentified deposit and its related safety issues – I. Corrosion product deposition and heat transfer

CRUD depositions on fuel cladding are the main cause of power shift and localized corrosion in nuclear power plants. This paper is the first of a three-part study concerning the formation mechanism of CRUD depositions and its related heat transfer issues. In this paper, CRUD depositions are obtained under subcooled boiling conditions in 2 × 2 rod array channels via accelerated deposition method to explore corrosion product deposition and its feedback on heat transfer. Imbalance of deposition and erosion at initial stage causes fouling resistance to increase first and then decrease. CRUD growth is proposed as a relatively pure fouling process combining soluble precipitation and particulate aggregation. Through high-resolution characterizations, boiling chimney diameters span from 3 μm to a dozen microns. Principal components are nickel ferrite and nickel elemental with Fe/Ni ratio of 1.9:1. Static contact angle decreases to less than 30°. Effective CRUD thermal conductivity decreases with the increase of heat flux with 1.3866 W/(m × K) on average. The results of this study provide a precise method for understanding corrosion product deposition and its impact on heat transfer to further establish accurate CRUD-related models and predict CRUD-related safety issues.

A simple approach to produce hydrophobic biobased coatings using methylcellulose and organosolv lignin.

Substituting plastics with circular and sustainable alternatives has increasingly become a priority. Protective coatings, crucial components in numerous industries, are now in demand for biodegradable options to replace their plastic-based counterparts. Being one of nature's most abundant components, lignin remains underutilized, and this study focuses on investigating its potential for the production of biobased coatings. The method used here involved formulating coating suspensions by mixing methylcellulose and organosolv lignin powders and adding water to the mixture. Glass wafers were coated with the formulated suspensions using spin-coating. The morphology of the coated surfaces was assessed using optical and scanning electron microscopy. In addition, the wettability of the surfaces was examined through water contact angle experiments, and a numerical model was introduced to predict the water contact angle evolution over time. The results revealed that the sample coated with a 2.5 wt% lignin suspension exhibited the highest initial contact angle (114°), with a decreasing trend as the lignin fraction increases. Moreover, coatings with 3.5 wt% lignin and above exhibited lower surface coverage due to lignin particle aggregation and surface defects. By approximating the water droplet on the surface as a spherical cap, the introduced numerical model successfully predicted the time-dependent evolution of the water contact angle by showing strong alignment with experimental results. Taken altogether, we have showcased here a method for modifying coating properties-in a practical sense from water-absorbent to splash-proof-using readily available forest-based materials. This advancement is paving the way for sustainable protective packaging, aiming to replace styrofoam in the electronics and food industries.

Competing Effects of Temperature and Polymer Concentration on Evolution of Re-entrant Interactions in the Nanoparticle-Block Copolymer System.

An interesting evolution of the re-entrant interaction has been observed in an anionic silica nanoparticle (NP)-block copolymer (P85) dispersion due to mutually competing effects of temperature and polymer concentration. It has been demonstrated that a rise in the temperature leads to an evolution of attraction in the system, which interestingly diminishes on increasing the polymer concentration. Consequently, the system exhibits a re-entrant transition from repulsive to attractive and back to repulsive at a given temperature but with respect to the increasing polymer concentration, within a selected region of concentration and temperature. The intriguing observations have been elucidated based on the temperature/concentration-dependent modifications in the interactions governing the system, as probed by contrast-variation small-angle neutron scattering. The initial transition from the repulsive to attractive system is attributed to the temperature-driven enhancement in the hydrophobicity of the amphiphilic triblock copolymer (P85) adsorbed on nanoparticles. The strength and range of this attraction are found to be more than van der Waals attraction while relatively less than electrostatic interaction. At higher polymer concentrations, the saturation of polymer adsorption on nanoparticles introduces additional steric repulsion along with electrostatic interaction between their conjugates, effectively reducing the strength of the attraction. However, with a significant increase in temperature (>75 °C), the attraction again dominates the system, which eventually leads to the particle aggregation at all the measured polymer concentrations (>0.1 wt %). Our study provides useful inputs to develop smart NP-polymer composites having capabilities to respond to external stimuli such as temperature/concentration variation.

Competing Effects of Temperature and Polymer Concentration on Evolution of Re-entrant Interactions in the Nanoparticle-Block Copolymer System.

An interesting evolution of the re-entrant interaction has been observed in an anionic silica nanoparticle (NP)-block copolymer (P85) dispersion due to mutually competing effects of temperature and polymer concentration. It has been demonstrated that a rise in the temperature leads to an evolution of attraction in the system, which interestingly diminishes on increasing the polymer concentration. Consequently, the system exhibits a re-entrant transition from repulsive to attractive and back to repulsive at a given temperature but with respect to the increasing polymer concentration, within a selected region of concentration and temperature. The intriguing observations have been elucidated based on the temperature/concentration-dependent modifications in the interactions governing the system, as probed by contrast-variation small-angle neutron scattering. The initial transition from the repulsive to attractive system is attributed to the temperature-driven enhancement in the hydrophobicity of the amphiphilic triblock copolymer (P85) adsorbed on nanoparticles. The strength and range of this attraction are found to be more than van der Waals attraction while relatively less than electrostatic interaction. At higher polymer concentrations, the saturation of polymer adsorption on nanoparticles introduces additional steric repulsion along with electrostatic interaction between their conjugates, effectively reducing the strength of the attraction. However, with a significant increase in temperature (>75 °C), the attraction again dominates the system, which eventually leads to the particle aggregation at all the measured polymer concentrations (>0.1 wt %). Our study provides useful inputs to develop smart NP-polymer composites having capabilities to respond to external stimuli such as temperature/concentration variation.

Photocatalytic Degradation of Losartan with BiOCl/Sepiolite Nanocomposites

Developing highly active and available, environmentally friendly, and low-cost photocatalytic materials is one of the most popular topics in photocatalytic degradation systems. In the present study, a series of BiOCl/Sepiolite composite photocatalysts were prepared (in the range of 5%BiOCl/Sepiolite–30%BiOCl/Sepiolite). Their characterization was conducted using X-ray diffraction, diffuse reflectance spectroscopy, scanning electron microscopy, nitrogen physical physisorption at the temperature of liquid nitrogen (77 K), and attenuated total reflectance-Fourier transform infrared spectroscopy. Results showed that composite photocatalysts possess superior efficiency than the parent materials for losartan, an antihypertensive agent, degradation in water, with the sample with only 10%wt. BiOCl shows the highest performance. The beneficial effect of the addition of sepiolite to BiOCl is derived from the increase in surface area, the prevention of particle aggregation, and the efficient separation of photogenerated species. Increasing catalyst concentration from 125 mg/L up to 500 mg/L was accompanied by an increase in the apparent kinetic constant from 0.077 min−1 to 0.197 min−1 while varying losartan concentration from 0.25 to 5.00 mg/L slowed down the removal efficiency. In addition, losartan degradation was only partially hampered in the case of bottled water, whereas it was practically stopped in a secondary wastewater effluent. Overall, this study serves as a useful guide for using geopolymers in photocatalytic applications.

Performance Requirements and Optimum Mix Proportion of High-Volume Fly Ash 3D Printable Concrete

In this study, a procedure for mixture design was proposed with the aim of meeting the requirements of extrudability, buildability, and shape stability in 3D printable concrete. Optimum water/binder ratio, sand/binder ratio, binder type, utilization ratio, aggregate particle distribution and quantity, and type and utilization ratio of chemical admixtures were determined for 3D printable concrete in terms of print quality and shape stability criteria. A total of 32 different mixtures were produced. It was determined that mixtures produced using a binder content with approximately 40% fly ash, a w/b ratio of 0.35, and aggregates with Dmax of 1 mm exhibit acceptable characteristics. Investigations were also conducted into the thixotropic behavior, rheological characteristics, and mechanical properties of the mixes that were deemed acceptable. As a result, it was determined that the increase in the amount of fly ash usage positively affected the buildability of the printed layers. Additionally, the dynamic yield stress ranging from 114 to 204 Pa, viscosity ranging from 22 to 43 Pa.s, and structural build-up value ranges suitable for the production of 3D printable concrete mixtures were determined.

Impact of NaCl perturbation on physicochemical and structural properties of preheat–treated egg white protein modulating foaming property

This study aimed to investigate the mechanism of NaCl perturbed preheat–treated egg white proteins' (EWPs) physicochemical and structural properties to modulate the foaming property (FP). The results revealed that NaCl regulated the salinolysis (5 mM) – salt precipitation (50 mM) – gradual or complete coverage with hydrated Na+ of the hydration layer (100–300 mM) – enhanced Cl− hydration repulsion (500 mM) of EWP, showing a gradual decrease in aggregates particle size, and reversibility of structural freedom, including moleculer flexibility and surface hydrophobicity. Whereas preheating temperature affected the secondary structure rearrangement and tertiary conformation exposure, and excessive temperature reduced foaming capacity while enhanced foam stability, with a tight correlation between NaCl–mediated EWPs’ FP and the extent of Na+ covering the hydration layer. The findings provide a theoretical basis for processing factors to modulate the protein hydration layer to influence the functional properties.

Performance Requirements and Optimum Mix Proportion of High-Volume Fly Ash 3D Printable Concrete

In this study, a procedure for mixture design was proposed with the aim of meeting the requirements of extrudability, buildability, and shape stability in 3D printable concrete. Optimum water/binder ratio, sand/binder ratio, binder type, utilization ratio, aggregate particle distribution and quantity, and type and utilization ratio of chemical admixtures were determined for 3D printable concrete in terms of print quality and shape stability criteria. A total of 32 different mixtures were produced. It was determined that mixtures produced using a binder content with approximately 40% fly ash, a w/b ratio of 0.35, and aggregates with Dmax of 1 mm exhibit acceptable characteristics. Investigations were also conducted into the thixotropic behavior, rheological characteristics, and mechanical properties of the mixes that were deemed acceptable. As a result, it was determined that the increase in the amount of fly ash usage positively affected the buildability of the printed layers. Additionally, the dynamic yield stress ranging from 114 to 204 Pa, viscosity ranging from 22 to 43 Pa.s, and structural build-up value ranges suitable for the production of 3D printable concrete mixtures were determined.

Formation of the crust on the surface of cold-climate aeolian quartz grains – A nano-scale study

Sand-sized quartz grains selected from sediments of a Pleistocene inland dune (eastern Poland) were subjected to a series of laboratory analyses, including grain-size distribution, morphoscopy analysis, microtextural analysis using scanning electron microscope (SEM) and nanostructural analysis using transmission electron microscope (TEM). The results indicate the presence of a crust on the surface of all of the studied quartz grains and a surprisingly low number of aeolian-induced mechanical microtextures. The TEM examination identifies illite-smectite assemblages as the main component of the crust, accompanied by amorphous silica, local accumulation of Fe, K, Ca, Mg oxides, and mineral particles (quartz, K-feldspar, chlorite). The thickness of the crust reaches approx. 0.1–0.2 μm and varies from the minimum on micro-protrusions up to the maximum in micro-cavities. Here, we present a new theory on the origin of the crust observed on the surface of cold-climate aeolian quartz grains. We postulate that the crust is formed within a near-surface saltation layer during active aeolian transport of sand-sized grains and clay-sized particles operating under cold-climate conditions. The development of abrasion features and the formation of the crust are interpreted here to occur simultaneously and continuously during the aeolian transport. The formation of the crust results from specific properties of aeolian transport (i.e. self-induced electrification and electrification mechanisms of quartz grains) and the quartz grains themselves (i.e. grain shape and surface microtopography).

Insight into the Effect of Nanobubbles on Fine Muscovite Powder Flotation in Different Dodecylamine Concentrations and Stirring Intensities: Kinetics and Mechanism

Flotation-introduced nanobubbles were expected to be an efficient and economical method to recover fine muscovite. This study aimed to explore the mechanism of the change appearing in flotation after introducing nanobubbles through micro-flotation, particle vision and measurement, flotation kinetics, and induction time measurement. The results of micro-flotation, which respectively feed muscovite or muscovite pretreated with nanobubbles in different concentrations of dodecylamine (DDA), were fitted with four flotation kinetic models using Origin. Different methods were used to examine how the introduction of nanobubbles affected the flotation process. The results showed that nanobubbles improved both the flotation rate and recovery of muscovite. Nanobubbles played different roles in different stirring intensities. At low stirring intensity, nanobubbles did not perform well. In suitable stirring intensity, nanobubbles helped particles aggregate and improved the collision probability between bubbles and minerals. However, at high stirring intensity, shear forces caused by ultra-high fluid velocities could disrupt particle aggregation.

Development of a broad-spectrum therapeutic Fc-nanobody for human noroviruses.

Human norovirus was discovered more than five decades ago and is a widespread cause of outbreaks of acute gastroenteritis. There are no approved vaccines or antivirals currently available. However, norovirus inhibitors, including capsid-specific monoclonal antibodies (Mabs) and nanobodies, have recently shown promising results. Several Mabs and nanobodies were found to inhibit norovirus replication using a human intestinal enteroid (HIE) culture system and/or could block norovirus attachment to histo-blood group antigen (HBGA) co-factors. In our pursuit to develop a single broad-spectrum norovirus therapeutic, we continued our analysis and development of a cross-reactive and HBGA interfering nanobody (NB26). To improve NB26 binding capacity and therapeutic potential, we conjugated NB26 onto a human IgG Fc domain (Fc-NB26). We confirmed that Fc-NB26 cross-reacts with genetically diverse GII genotype capsid protruding (P) domains (GII.8, GII.14, GII.17, GII.24, GII.26, and GII.NA1) using a direct enzyme-linked immunosorbent assay. Furthermore, X-ray crystallography structures of these P domains and structures of other GII genotypes reveal that the NB26 binding site is largely conserved, validating its broad reactivity. We showed that Fc-NB26 has ~100-fold higher affinity toward the norovirus P domain compared to native NB26. We also found that both NB26 and Fc-NB26 neutralize human norovirus replication in the HIE culture system. Furthermore, the mode of inhibition confirmed that like NB26, Fc-NB26 caused norovirus particle disassembly and aggregation. Overall, these new findings demonstrate that structural modifications to nanobodies can improve their therapeutic potential.IMPORTANCEDeveloping vaccines and antivirals against norovirus remains a challenge, mainly due to the constant genetic and antigenic evolution. Moreover, re-infection with genetically related and/or antigenic variants is not uncommon. We further developed our leading norovirus nanobody (NB26) that indirectly interfered with norovirus binding to HBGAs, by converting NB26 into a dimeric Fc-linked Nanobody (Fc-NB26). We found that Fc-NB26 had improved binding affinity and neutralization capacity compared with native NB26. Using X-ray crystallography, we showed this nanobody engaged highly conserved capsid residues among genetically diverse noroviruses. Development of such broadly reactive potent therapeutic nanobodies delivered as a slow-releasing prophylactic could be of exceptional value for norovirus outbreaks, especially for the prevention or treatment of severe acute gastroenteritis in high-risk groups such as the young, elderly, and immunocompromised.

DNA sensing based on aggregation of Janus particles using dynamic light scattering

BackgroundThe aggregation of isotropic particles through interparticle reactions poses a challenge in control due to the ability of all surfaces to bind to each other, rendering the quantitative detection of such interparticle reactions based on particle size difficult. Here, we proposed a novel detection scheme for DNA utilizing an assembly of Janus particles (JPs) employing dynamic light scattering (DLS). DNA molecules are tethered on one hemisphere of the JP, while the other hemisphere retains its hydrophobic properties. ResultsAggregation of JPs was induced by the sandwich hybridization of target DNA between them. The assembly of JPs was effectively monitored by the changes in hydrodynamic diameter detected by DLS, revealing that aggregation peaks at 2–3 particles and further reaction was hindered due to the inability of one hemisphere of the JP to interact with another JP. The target DNA demonstrated detectability at concentrations as low as several tens of pM to several nM using a digital sensing method. The two types of target DNA, such as simple (14 base pairs) and HIV-2 specific sequences (20 base pairs) were detectable at nM and pM levels, respectively. Moreover, we substantiated the robustness of our detection scheme through stoichiometric calculations based on an equilibrium model. The present detection mechanism was well explained based on the binding affinity of DNA hybridization. SignificanceThis detection method harnesses the anisotropic nature of JPs and represents the first detection approach based on aggregation. By altering the modification molecules on JPs to match target molecules, such as proteins and organic compounds, a wide range of versatile molecules can be detected using this scheme with high sensitivity. This underscores the broad applicability of the present method.